MPI initialized with 4 MPI processes MPI initialized with thread support level 3 OMP initialized with 4 OMP threads AMReX (23.04-37-ga6e89ecc1175) initialized Starting run at 05:03:22 UTC on 2023-04-27. Successfully read inputs file ... Castro git describe: 23.04-17-gf9272dfba AMReX git describe: 23.04-37-ga6e89ecc1 Microphysics git describe: 23.04-6-gfc4258c6 reading extern runtime parameters ... Initializing rate table 19 Species: H1 He3 He4 C12 N14 O16 Ne20 Mg24 Si28 S32 Ar36 Ca40 Ti44 Cr48 Fe52 Fe54 Ni56 n p Successfully read inputs file ... Initializing the data at level 0 Done initializing the level 0 data ...estimated hydro-limited timestep at level 0: 1.600525315e-07 ...hydro-limited CFL timestep constrained at (i) = (289) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.600525315e-07 TIME= 0 MASS = 3.2768e+13 TIME= 0 XMOM = 0 TIME= 0 YMOM = 0 TIME= 0 ZMOM = 0 TIME= 0 ANG MOM X = 0 TIME= 0 ANG MOM Y = 0 TIME= 0 ANG MOM Z = 0 TIME= 0 RHO*e = 2.386310753e+31 TIME= 0 RHO*K = 0 TIME= 0 RHO*E = 2.386310753e+31 TIME= 0 CENTER OF MASS X-LOC = 81920 TIME= 0 CENTER OF MASS X-VEL = 0 TIME= 0 CENTER OF MASS Y-LOC = 0 TIME= 0 CENTER OF MASS Y-VEL = 0 TIME= 0 CENTER OF MASS Z-LOC = 0 TIME= 0 CENTER OF MASS Z-VEL = 0 TIME= 0 MAXIMUM TEMPERATURE = 4000000001 TIME= 0 MAXIMUM DENSITY = 200000000 TIME= 0 MAXIMUM T_S / T_E = 0 INITIAL GRIDS Level 0 4 grids 1024 cells 100 % of domain smallest grid: 256 biggest grid: 256 PLOTFILE: file = Detonation-SDC_plt00000 Write plotfile time = 0.01233769 seconds ...estimated hydro-limited timestep at level 0: 1.600525315e-07 ...hydro-limited CFL timestep constrained at (i) = (288) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.600525315e-07 [Level 0 step 1] ADVANCE with dt = 1.600525315e-08  Beginning subcycle 1 starting at time 0 with dt = 1.600525315e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000894004 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.146238225 ...estimated hydro-limited timestep at level 0: 1.595651649e-07 ...hydro-limited CFL timestep constrained at (i) = (290) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.595651649e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000929548 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.146818935 ...estimated hydro-limited timestep at level 0: 1.595651649e-07 ...hydro-limited CFL timestep constrained at (i) = (287) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.595651649e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.003421752498 [Level 0 step 1] Advanced 1024 cells TIME= 1.600525315e-08 MASS = 3.2768e+13 TIME= 1.600525315e-08 XMOM = 4.079271951e+17 TIME= 1.600525315e-08 YMOM = 0 TIME= 1.600525315e-08 ZMOM = 0 TIME= 1.600525315e-08 ANG MOM X = 0 TIME= 1.600525315e-08 ANG MOM Y = 0 TIME= 1.600525315e-08 ANG MOM Z = 0 TIME= 1.600525315e-08 RHO*e = 2.391995444e+31 TIME= 1.600525315e-08 RHO*K = 8.04585677e+23 TIME= 1.600525315e-08 RHO*E = 2.391995524e+31 TIME= 1.600525315e-08 CENTER OF MASS X-LOC = 81920.00012 TIME= 1.600525315e-08 CENTER OF MASS X-VEL = 12448.95005 TIME= 1.600525315e-08 CENTER OF MASS Y-LOC = 0 TIME= 1.600525315e-08 CENTER OF MASS Y-VEL = 0 TIME= 1.600525315e-08 CENTER OF MASS Z-LOC = 0 TIME= 1.600525315e-08 CENTER OF MASS Z-VEL = 0 TIME= 1.600525315e-08 MAXIMUM TEMPERATURE = 4066182871 TIME= 1.600525315e-08 MAXIMUM DENSITY = 200062419.6 TIME= 1.600525315e-08 MAXIMUM T_S / T_E = 0.1962090989 [STEP 1] Coarse TimeStep time: 0.300829329 [STEP 1] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 1 TIME = 1.600525315e-08 DT = 1.600525315e-08 ...estimated hydro-limited timestep at level 0: 1.595651649e-07 ...hydro-limited CFL timestep constrained at (i) = (0) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.595651649e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.595651649e-07 ... but limiting to: 1.680551581e-08 = 1.05 * 1.600525315e-08 [Level 0 step 2] ADVANCE with dt = 1.680551581e-08  Beginning subcycle 1 starting at time 1.600525315e-08 with dt = 1.680551581e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000872919 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.075170135 ...estimated hydro-limited timestep at level 0: 1.581498754e-07 ...hydro-limited CFL timestep constrained at (i) = (291) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.581498754e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000835524 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.075626457 ...estimated hydro-limited timestep at level 0: 1.581498754e-07 ...hydro-limited CFL timestep constrained at (i) = (291) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.581498754e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.006519383688 [Level 0 step 2] Advanced 1024 cells TIME= 3.281076896e-08 MASS = 3.2768e+13 TIME= 3.281076896e-08 XMOM = 8.526775068e+17 TIME= 3.281076896e-08 YMOM = 0 TIME= 3.281076896e-08 ZMOM = 0 TIME= 3.281076896e-08 ANG MOM X = 0 TIME= 3.281076896e-08 ANG MOM Y = 0 TIME= 3.281076896e-08 ANG MOM Z = 0 TIME= 3.281076896e-08 RHO*e = 2.408721533e+31 TIME= 3.281076896e-08 RHO*K = 3.435290002e+24 TIME= 3.281076896e-08 RHO*E = 2.408721877e+31 TIME= 3.281076896e-08 CENTER OF MASS X-LOC = 81920.00052 TIME= 3.281076896e-08 CENTER OF MASS X-VEL = 26021.65243 TIME= 3.281076896e-08 CENTER OF MASS Y-LOC = 0 TIME= 3.281076896e-08 CENTER OF MASS Y-VEL = 0 TIME= 3.281076896e-08 CENTER OF MASS Z-LOC = 0 TIME= 3.281076896e-08 CENTER OF MASS Z-VEL = 0 TIME= 3.281076896e-08 MAXIMUM TEMPERATURE = 4254856236 TIME= 3.281076896e-08 MAXIMUM DENSITY = 200235548.9 TIME= 3.281076896e-08 MAXIMUM T_S / T_E = 0.230689917 [STEP 2] Coarse TimeStep time: 0.158662787 [STEP 2] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 2 TIME = 3.281076896e-08 DT = 1.680551581e-08 ...estimated hydro-limited timestep at level 0: 1.581498754e-07 ...hydro-limited CFL timestep constrained at (i) = (287) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.581498754e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.581498754e-07 ... but limiting to: 1.76457916e-08 = 1.05 * 1.680551581e-08 [Level 0 step 3] ADVANCE with dt = 1.76457916e-08  Beginning subcycle 1 starting at time 3.281076896e-08 with dt = 1.76457916e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000823664 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.101916719 ...estimated hydro-limited timestep at level 0: 1.561477941e-07 ...hydro-limited CFL timestep constrained at (i) = (288) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.561477941e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000996239 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.106072192 ...estimated hydro-limited timestep at level 0: 1.561477941e-07 ...hydro-limited CFL timestep constrained at (i) = (291) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.561477941e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.004780649983 [Level 0 step 3] Advanced 1024 cells TIME= 5.045656057e-08 MASS = 3.2768e+13 TIME= 5.045656057e-08 XMOM = 1.351460215e+18 TIME= 5.045656057e-08 YMOM = 0 TIME= 5.045656057e-08 ZMOM = 0 TIME= 5.045656057e-08 ANG MOM X = 0 TIME= 5.045656057e-08 ANG MOM Y = 0 TIME= 5.045656057e-08 ANG MOM Z = 0 TIME= 5.045656057e-08 RHO*e = 2.433630847e+31 TIME= 5.045656057e-08 RHO*K = 8.467404748e+24 TIME= 5.045656057e-08 RHO*E = 2.433631694e+31 TIME= 5.045656057e-08 CENTER OF MASS X-LOC = 81920.00124 TIME= 5.045656057e-08 CENTER OF MASS X-VEL = 41243.29269 TIME= 5.045656057e-08 CENTER OF MASS Y-LOC = 0 TIME= 5.045656057e-08 CENTER OF MASS Y-VEL = 0 TIME= 5.045656057e-08 CENTER OF MASS Z-LOC = 0 TIME= 5.045656057e-08 CENTER OF MASS Z-VEL = 0 TIME= 5.045656057e-08 MAXIMUM TEMPERATURE = 4524933071 TIME= 5.045656057e-08 MAXIMUM DENSITY = 200524428.9 TIME= 5.045656057e-08 MAXIMUM T_S / T_E = 0.3403388109 [STEP 3] Coarse TimeStep time: 0.216268795 [STEP 3] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 3 TIME = 5.045656057e-08 DT = 1.76457916e-08 ...estimated hydro-limited timestep at level 0: 1.561477941e-07 ...hydro-limited CFL timestep constrained at (i) = (291) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.561477941e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.561477941e-07 ... but limiting to: 1.852808118e-08 = 1.05 * 1.76457916e-08 [Level 0 step 4] ADVANCE with dt = 1.852808118e-08  Beginning subcycle 1 starting at time 5.045656057e-08 with dt = 1.852808118e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000912287 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.080499419 ...estimated hydro-limited timestep at level 0: 1.540418629e-07 ...hydro-limited CFL timestep constrained at (i) = (305) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.540418629e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.00084027 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.080991925 ...estimated hydro-limited timestep at level 0: 1.540827255e-07 ...hydro-limited CFL timestep constrained at (i) = (305) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.540827255e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.006107877184 [Level 0 step 4] Advanced 1024 cells TIME= 6.898464175e-08 MASS = 3.2768e+13 TIME= 6.898464175e-08 XMOM = 1.912210957e+18 TIME= 6.898464175e-08 YMOM = 0 TIME= 6.898464175e-08 ZMOM = 0 TIME= 6.898464175e-08 ANG MOM X = 0 TIME= 6.898464175e-08 ANG MOM Y = 0 TIME= 6.898464175e-08 ANG MOM Z = 0 TIME= 6.898464175e-08 RHO*e = 2.455626841e+31 TIME= 6.898464175e-08 RHO*K = 1.686660354e+25 TIME= 6.898464175e-08 RHO*E = 2.455628528e+31 TIME= 6.898464175e-08 CENTER OF MASS X-LOC = 81920.00232 TIME= 6.898464175e-08 CENTER OF MASS X-VEL = 58356.04727 TIME= 6.898464175e-08 CENTER OF MASS Y-LOC = 0 TIME= 6.898464175e-08 CENTER OF MASS Y-VEL = 0 TIME= 6.898464175e-08 CENTER OF MASS Z-LOC = 0 TIME= 6.898464175e-08 CENTER OF MASS Z-VEL = 0 TIME= 6.898464175e-08 MAXIMUM TEMPERATURE = 4753569980 TIME= 6.898464175e-08 MAXIMUM DENSITY = 200928989.8 TIME= 6.898464175e-08 MAXIMUM T_S / T_E = 0.3957600964 [STEP 4] Coarse TimeStep time: 0.169223474 [STEP 4] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 4 TIME = 6.898464175e-08 DT = 1.852808118e-08 ...estimated hydro-limited timestep at level 0: 1.540827255e-07 ...hydro-limited CFL timestep constrained at (i) = (305) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.540827255e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.540827255e-07 ... but limiting to: 1.945448524e-08 = 1.05 * 1.852808118e-08 [Level 0 step 5] ADVANCE with dt = 1.945448524e-08  Beginning subcycle 1 starting at time 6.898464175e-08 with dt = 1.945448524e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.00083275 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.066577236 ...estimated hydro-limited timestep at level 0: 1.511322277e-07 ...hydro-limited CFL timestep constrained at (i) = (306) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.511322277e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000832429 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.066549975 ...estimated hydro-limited timestep at level 0: 1.511944194e-07 ...hydro-limited CFL timestep constrained at (i) = (306) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.511944194e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.007360523048 [Level 0 step 5] Advanced 1024 cells TIME= 8.843912699e-08 MASS = 3.2768e+13 TIME= 8.843912699e-08 XMOM = 2.533080098e+18 TIME= 8.843912699e-08 YMOM = 0 TIME= 8.843912699e-08 ZMOM = 0 TIME= 8.843912699e-08 ANG MOM X = 0 TIME= 8.843912699e-08 ANG MOM Y = 0 TIME= 8.843912699e-08 ANG MOM Z = 0 TIME= 8.843912699e-08 RHO*e = 2.473135278e+31 TIME= 8.843912699e-08 RHO*K = 2.995052054e+25 TIME= 8.843912699e-08 RHO*E = 2.473138274e+31 TIME= 8.843912699e-08 CENTER OF MASS X-LOC = 81920.00378 TIME= 8.843912699e-08 CENTER OF MASS X-VEL = 77303.46979 TIME= 8.843912699e-08 CENTER OF MASS Y-LOC = 0 TIME= 8.843912699e-08 CENTER OF MASS Y-VEL = 0 TIME= 8.843912699e-08 CENTER OF MASS Z-LOC = 0 TIME= 8.843912699e-08 CENTER OF MASS Z-VEL = 0 TIME= 8.843912699e-08 MAXIMUM TEMPERATURE = 4928705884 TIME= 8.843912699e-08 MAXIMUM DENSITY = 201443865.6 TIME= 8.843912699e-08 MAXIMUM T_S / T_E = 0.7139219589 [STEP 5] Coarse TimeStep time: 0.140699364 [STEP 5] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 5 TIME = 8.843912699e-08 DT = 1.945448524e-08 ...estimated hydro-limited timestep at level 0: 1.511944194e-07 ...hydro-limited CFL timestep constrained at (i) = (306) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.511944194e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.511944194e-07 ... but limiting to: 2.04272095e-08 = 1.05 * 1.945448524e-08 [Level 0 step 6] ADVANCE with dt = 2.04272095e-08  Beginning subcycle 1 starting at time 8.843912699e-08 with dt = 2.04272095e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000835188 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.057148339 ...estimated hydro-limited timestep at level 0: 1.483837843e-07 ...hydro-limited CFL timestep constrained at (i) = (306) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.483837843e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000926894 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.056627485 ...estimated hydro-limited timestep at level 0: 1.483483879e-07 ...hydro-limited CFL timestep constrained at (i) = (306) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.483483879e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.00853587368 [Level 0 step 6] Advanced 1024 cells TIME= 1.088663365e-07 MASS = 3.2768e+13 TIME= 1.088663365e-07 XMOM = 3.212605726e+18 TIME= 1.088663365e-07 YMOM = 0 TIME= 1.088663365e-07 ZMOM = 0 TIME= 1.088663365e-07 ANG MOM X = 0 TIME= 1.088663365e-07 ANG MOM Y = 0 TIME= 1.088663365e-07 ANG MOM Z = 0 TIME= 1.088663365e-07 RHO*e = 2.488501851e+31 TIME= 1.088663365e-07 RHO*K = 4.670678916e+25 TIME= 1.088663365e-07 RHO*E = 2.488506522e+31 TIME= 1.088663365e-07 CENTER OF MASS X-LOC = 81920.00702 TIME= 1.088663365e-07 CENTER OF MASS X-VEL = 98040.94622 TIME= 1.088663365e-07 CENTER OF MASS Y-LOC = 0 TIME= 1.088663365e-07 CENTER OF MASS Y-VEL = 0 TIME= 1.088663365e-07 CENTER OF MASS Z-LOC = 0 TIME= 1.088663365e-07 CENTER OF MASS Z-VEL = 0 TIME= 1.088663365e-07 MAXIMUM TEMPERATURE = 5079292943 TIME= 1.088663365e-07 MAXIMUM DENSITY = 202541880.8 TIME= 1.088663365e-07 MAXIMUM T_S / T_E = 0.299973781 [STEP 6] Coarse TimeStep time: 0.121602488 [STEP 6] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 6 TIME = 1.088663365e-07 DT = 2.04272095e-08 ...estimated hydro-limited timestep at level 0: 1.483483879e-07 ...hydro-limited CFL timestep constrained at (i) = (306) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.483483879e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.483483879e-07 ... but limiting to: 2.144856998e-08 = 1.05 * 2.04272095e-08 [Level 0 step 7] ADVANCE with dt = 2.144856998e-08  Beginning subcycle 1 starting at time 1.088663365e-07 with dt = 2.144856998e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000821826 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.061205439 ...estimated hydro-limited timestep at level 0: 1.465758654e-07 ...hydro-limited CFL timestep constrained at (i) = (306) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.465758654e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000921089 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.061658026 ...estimated hydro-limited timestep at level 0: 1.465673471e-07 ...hydro-limited CFL timestep constrained at (i) = (306) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.465673471e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.007933350866 [Level 0 step 7] Advanced 1024 cells TIME= 1.303149065e-07 MASS = 3.2768e+13 TIME= 1.303149065e-07 XMOM = 3.951978971e+18 TIME= 1.303149065e-07 YMOM = 0 TIME= 1.303149065e-07 ZMOM = 0 TIME= 1.303149065e-07 ANG MOM X = 0 TIME= 1.303149065e-07 ANG MOM Y = 0 TIME= 1.303149065e-07 ANG MOM Z = 0 TIME= 1.303149065e-07 RHO*e = 2.502696981e+31 TIME= 1.303149065e-07 RHO*K = 6.848727275e+25 TIME= 1.303149065e-07 RHO*E = 2.50270383e+31 TIME= 1.303149065e-07 CENTER OF MASS X-LOC = 81920.01081 TIME= 1.303149065e-07 CENTER OF MASS X-VEL = 120604.827 TIME= 1.303149065e-07 CENTER OF MASS Y-LOC = 0 TIME= 1.303149065e-07 CENTER OF MASS Y-VEL = 0 TIME= 1.303149065e-07 CENTER OF MASS Z-LOC = 0 TIME= 1.303149065e-07 CENTER OF MASS Z-VEL = 0 TIME= 1.303149065e-07 MAXIMUM TEMPERATURE = 5215379415 TIME= 1.303149065e-07 MAXIMUM DENSITY = 203751365.5 TIME= 1.303149065e-07 MAXIMUM T_S / T_E = 0.1427171293 [STEP 7] Coarse TimeStep time: 0.130688922 [STEP 7] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 7 TIME = 1.303149065e-07 DT = 2.144856998e-08 ...estimated hydro-limited timestep at level 0: 1.465673471e-07 ...hydro-limited CFL timestep constrained at (i) = (306) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.465673471e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.465673471e-07 ... but limiting to: 2.252099848e-08 = 1.05 * 2.144856998e-08 [Level 0 step 8] ADVANCE with dt = 2.252099848e-08  Beginning subcycle 1 starting at time 1.303149065e-07 with dt = 2.252099848e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000833817 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.055339658 ...estimated hydro-limited timestep at level 0: 1.449654536e-07 ...hydro-limited CFL timestep constrained at (i) = (306) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.449654536e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.00083465 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.055266214 ...estimated hydro-limited timestep at level 0: 1.449863002e-07 ...hydro-limited CFL timestep constrained at (i) = (306) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.449863002e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.008781481988 [Level 0 step 8] Advanced 1024 cells TIME= 1.528359049e-07 MASS = 3.2768e+13 TIME= 1.528359049e-07 XMOM = 4.753439088e+18 TIME= 1.528359049e-07 YMOM = 0 TIME= 1.528359049e-07 ZMOM = 0 TIME= 1.528359049e-07 ANG MOM X = 0 TIME= 1.528359049e-07 ANG MOM Y = 0 TIME= 1.528359049e-07 ANG MOM Z = 0 TIME= 1.528359049e-07 RHO*e = 2.516134955e+31 TIME= 1.528359049e-07 RHO*K = 9.703263442e+25 TIME= 1.528359049e-07 RHO*E = 2.516144658e+31 TIME= 1.528359049e-07 CENTER OF MASS X-LOC = 81920.01457 TIME= 1.528359049e-07 CENTER OF MASS X-VEL = 145063.4487 TIME= 1.528359049e-07 CENTER OF MASS Y-LOC = 0 TIME= 1.528359049e-07 CENTER OF MASS Y-VEL = 0 TIME= 1.528359049e-07 CENTER OF MASS Z-LOC = 0 TIME= 1.528359049e-07 CENTER OF MASS Z-VEL = 0 TIME= 1.528359049e-07 MAXIMUM TEMPERATURE = 5341041833 TIME= 1.528359049e-07 MAXIMUM DENSITY = 204753949.7 TIME= 1.528359049e-07 MAXIMUM T_S / T_E = 0.232733118 [STEP 8] Coarse TimeStep time: 0.118198153 [STEP 8] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 8 TIME = 1.528359049e-07 DT = 2.252099848e-08 ...estimated hydro-limited timestep at level 0: 1.449863002e-07 ...hydro-limited CFL timestep constrained at (i) = (306) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.449863002e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.449863002e-07 ... but limiting to: 2.36470484e-08 = 1.05 * 2.252099848e-08 [Level 0 step 9] ADVANCE with dt = 2.36470484e-08  Beginning subcycle 1 starting at time 1.528359049e-07 with dt = 2.36470484e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000820062 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.053615617 ...estimated hydro-limited timestep at level 0: 1.362870697e-07 ...hydro-limited CFL timestep constrained at (i) = (307) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.362870697e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000830568 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.053913221 ...estimated hydro-limited timestep at level 0: 1.405187819e-07 ...hydro-limited CFL timestep constrained at (i) = (307) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.405187819e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.009024449834 [Level 0 step 9] Advanced 1024 cells TIME= 1.764829533e-07 MASS = 3.2768e+13 TIME= 1.764829533e-07 XMOM = 5.619783538e+18 TIME= 1.764829533e-07 YMOM = 0 TIME= 1.764829533e-07 ZMOM = 0 TIME= 1.764829533e-07 ANG MOM X = 0 TIME= 1.764829533e-07 ANG MOM Y = 0 TIME= 1.764829533e-07 ANG MOM Z = 0 TIME= 1.764829533e-07 RHO*e = 2.529639038e+31 TIME= 1.764829533e-07 RHO*K = 1.310040251e+26 TIME= 1.764829533e-07 RHO*E = 2.529652138e+31 TIME= 1.764829533e-07 CENTER OF MASS X-LOC = 81920.0187 TIME= 1.764829533e-07 CENTER OF MASS X-VEL = 171502.1832 TIME= 1.764829533e-07 CENTER OF MASS Y-LOC = 0 TIME= 1.764829533e-07 CENTER OF MASS Y-VEL = 0 TIME= 1.764829533e-07 CENTER OF MASS Z-LOC = 0 TIME= 1.764829533e-07 CENTER OF MASS Z-VEL = 0 TIME= 1.764829533e-07 MAXIMUM TEMPERATURE = 5458714438 TIME= 1.764829533e-07 MAXIMUM DENSITY = 206771926.4 TIME= 1.764829533e-07 MAXIMUM T_S / T_E = 1.885907003 [STEP 9] Coarse TimeStep time: 0.115041907 [STEP 9] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 9 TIME = 1.764829533e-07 DT = 2.36470484e-08 ...estimated hydro-limited timestep at level 0: 1.405187819e-07 ...hydro-limited CFL timestep constrained at (i) = (307) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.405187819e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.405187819e-07 ... but limiting to: 2.482940082e-08 = 1.05 * 2.36470484e-08 [Level 0 step 10] ADVANCE with dt = 2.482940082e-08  Beginning subcycle 1 starting at time 1.764829533e-07 with dt = 2.482940082e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.00082238 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.046301631 ...estimated hydro-limited timestep at level 0: 1.346969574e-07 ...hydro-limited CFL timestep constrained at (i) = (307) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.346969574e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000898615 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.046004847 ...estimated hydro-limited timestep at level 0: 1.344713654e-07 ...hydro-limited CFL timestep constrained at (i) = (307) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.344713654e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.01040533939 [Level 0 step 10] Advanced 1024 cells TIME= 2.013123542e-07 MASS = 3.2768e+13 TIME= 2.013123542e-07 XMOM = 6.554245729e+18 TIME= 2.013123542e-07 YMOM = 0 TIME= 2.013123542e-07 ZMOM = 0 TIME= 2.013123542e-07 ANG MOM X = 0 TIME= 2.013123542e-07 ANG MOM Y = 0 TIME= 2.013123542e-07 ANG MOM Z = 0 TIME= 2.013123542e-07 RHO*e = 2.542311011e+31 TIME= 2.013123542e-07 RHO*K = 1.674209474e+26 TIME= 2.013123542e-07 RHO*E = 2.542327753e+31 TIME= 2.013123542e-07 CENTER OF MASS X-LOC = 81920.02543 TIME= 2.013123542e-07 CENTER OF MASS X-VEL = 200019.7061 TIME= 2.013123542e-07 CENTER OF MASS Y-LOC = 0 TIME= 2.013123542e-07 CENTER OF MASS Y-VEL = 0 TIME= 2.013123542e-07 CENTER OF MASS Z-LOC = 0 TIME= 2.013123542e-07 CENTER OF MASS Z-VEL = 0 TIME= 2.013123542e-07 MAXIMUM TEMPERATURE = 6307124871 TIME= 2.013123542e-07 MAXIMUM DENSITY = 209034738.3 TIME= 2.013123542e-07 MAXIMUM T_S / T_E = 0.772845904 [STEP 10] Coarse TimeStep time: 0.100070536 [STEP 10] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 10 TIME = 2.013123542e-07 DT = 2.482940082e-08 ...estimated hydro-limited timestep at level 0: 1.344713654e-07 ...hydro-limited CFL timestep constrained at (i) = (307) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.344713654e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.344713654e-07 ... but limiting to: 2.607087086e-08 = 1.05 * 2.482940082e-08 [Level 0 step 11] ADVANCE with dt = 2.607087086e-08  Beginning subcycle 1 starting at time 2.013123542e-07 with dt = 2.607087086e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000829413 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.046685279 ...estimated hydro-limited timestep at level 0: 1.340289401e-07 ...hydro-limited CFL timestep constrained at (i) = (307) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.340289401e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000890995 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.046900429 ...estimated hydro-limited timestep at level 0: 1.3387069e-07 ...hydro-limited CFL timestep constrained at (i) = (307) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.3387069e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.01027333244 [Level 0 step 11] Advanced 1024 cells TIME= 2.27383225e-07 MASS = 3.2768e+13 TIME= 2.27383225e-07 XMOM = 7.560452571e+18 TIME= 2.27383225e-07 YMOM = 0 TIME= 2.27383225e-07 ZMOM = 0 TIME= 2.27383225e-07 ANG MOM X = 0 TIME= 2.27383225e-07 ANG MOM Y = 0 TIME= 2.27383225e-07 ANG MOM Z = 0 TIME= 2.27383225e-07 RHO*e = 2.554301031e+31 TIME= 2.27383225e-07 RHO*K = 2.139895154e+26 TIME= 2.27383225e-07 RHO*E = 2.55432243e+31 TIME= 2.27383225e-07 CENTER OF MASS X-LOC = 81920.03312 TIME= 2.27383225e-07 CENTER OF MASS X-VEL = 230726.702 TIME= 2.27383225e-07 CENTER OF MASS Y-LOC = 0 TIME= 2.27383225e-07 CENTER OF MASS Y-VEL = 0 TIME= 2.27383225e-07 CENTER OF MASS Z-LOC = 0 TIME= 2.27383225e-07 CENTER OF MASS Z-VEL = 0 TIME= 2.27383225e-07 MAXIMUM TEMPERATURE = 6307074141 TIME= 2.27383225e-07 MAXIMUM DENSITY = 210931834.1 TIME= 2.27383225e-07 MAXIMUM T_S / T_E = 0.1183933389 [STEP 11] Coarse TimeStep time: 0.101265391 [STEP 11] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 11 TIME = 2.27383225e-07 DT = 2.607087086e-08 ...estimated hydro-limited timestep at level 0: 1.3387069e-07 ...hydro-limited CFL timestep constrained at (i) = (307) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.3387069e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.3387069e-07 ... but limiting to: 2.737441441e-08 = 1.05 * 2.607087086e-08 [Level 0 step 12] ADVANCE with dt = 2.737441441e-08  Beginning subcycle 1 starting at time 2.27383225e-07 with dt = 2.737441441e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000892918 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.05132898 ...estimated hydro-limited timestep at level 0: 1.332919203e-07 ...hydro-limited CFL timestep constrained at (i) = (307) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.332919203e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000832157 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.051067765 ...estimated hydro-limited timestep at level 0: 1.333020966e-07 ...hydro-limited CFL timestep constrained at (i) = (307) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.333020966e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.009438186771 [Level 0 step 12] Advanced 1024 cells TIME= 2.547576394e-07 MASS = 3.2768e+13 TIME= 2.547576394e-07 XMOM = 8.642410019e+18 TIME= 2.547576394e-07 YMOM = 0 TIME= 2.547576394e-07 ZMOM = 0 TIME= 2.547576394e-07 ANG MOM X = 0 TIME= 2.547576394e-07 ANG MOM Y = 0 TIME= 2.547576394e-07 ANG MOM Z = 0 TIME= 2.547576394e-07 RHO*e = 2.566050343e+31 TIME= 2.547576394e-07 RHO*K = 2.697912963e+26 TIME= 2.547576394e-07 RHO*E = 2.566077322e+31 TIME= 2.547576394e-07 CENTER OF MASS X-LOC = 81920.04188 TIME= 2.547576394e-07 CENTER OF MASS X-VEL = 263745.4229 TIME= 2.547576394e-07 CENTER OF MASS Y-LOC = 0 TIME= 2.547576394e-07 CENTER OF MASS Y-VEL = 0 TIME= 2.547576394e-07 CENTER OF MASS Z-LOC = 0 TIME= 2.547576394e-07 CENTER OF MASS Z-VEL = 0 TIME= 2.547576394e-07 MAXIMUM TEMPERATURE = 6308465893 TIME= 2.547576394e-07 MAXIMUM DENSITY = 212127350.9 TIME= 2.547576394e-07 MAXIMUM T_S / T_E = 0.1471509377 [STEP 12] Coarse TimeStep time: 0.110188317 [STEP 12] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 12 TIME = 2.547576394e-07 DT = 2.737441441e-08 ...estimated hydro-limited timestep at level 0: 1.333020966e-07 ...hydro-limited CFL timestep constrained at (i) = (307) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.333020966e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.333020966e-07 ... but limiting to: 2.874313513e-08 = 1.05 * 2.737441441e-08 [Level 0 step 13] ADVANCE with dt = 2.874313513e-08  Beginning subcycle 1 starting at time 2.547576394e-07 with dt = 2.874313513e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000829349 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.052911812 ...estimated hydro-limited timestep at level 0: 1.296571772e-07 ...hydro-limited CFL timestep constrained at (i) = (308) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.296571772e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000833592 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.05277684 ...estimated hydro-limited timestep at level 0: 1.335919805e-07 ...hydro-limited CFL timestep constrained at (i) = (307) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.335919805e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.009167549939 [Level 0 step 13] Advanced 1024 cells TIME= 2.835007746e-07 MASS = 3.2768e+13 TIME= 2.835007746e-07 XMOM = 9.804500895e+18 TIME= 2.835007746e-07 YMOM = 0 TIME= 2.835007746e-07 ZMOM = 0 TIME= 2.835007746e-07 ANG MOM X = 0 TIME= 2.835007746e-07 ANG MOM Y = 0 TIME= 2.835007746e-07 ANG MOM Z = 0 TIME= 2.835007746e-07 RHO*e = 2.577796065e+31 TIME= 2.835007746e-07 RHO*K = 3.256548521e+26 TIME= 2.835007746e-07 RHO*E = 2.577828631e+31 TIME= 2.835007746e-07 CENTER OF MASS X-LOC = 81920.0518 TIME= 2.835007746e-07 CENTER OF MASS X-VEL = 299209.622 TIME= 2.835007746e-07 CENTER OF MASS Y-LOC = 0 TIME= 2.835007746e-07 CENTER OF MASS Y-VEL = 0 TIME= 2.835007746e-07 CENTER OF MASS Z-LOC = 0 TIME= 2.835007746e-07 CENTER OF MASS Z-VEL = 0 TIME= 2.835007746e-07 MAXIMUM TEMPERATURE = 6323739862 TIME= 2.835007746e-07 MAXIMUM DENSITY = 214049836.3 TIME= 2.835007746e-07 MAXIMUM T_S / T_E = 0.590975931 [STEP 13] Coarse TimeStep time: 0.113245312 [STEP 13] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 13 TIME = 2.835007746e-07 DT = 2.874313513e-08 ...estimated hydro-limited timestep at level 0: 1.335919805e-07 ...hydro-limited CFL timestep constrained at (i) = (307) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.335919805e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.335919805e-07 ... but limiting to: 3.018029188e-08 = 1.05 * 2.874313513e-08 [Level 0 step 14] ADVANCE with dt = 3.018029188e-08  Beginning subcycle 1 starting at time 2.835007746e-07 with dt = 3.018029188e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.00083247 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.046523932 ...estimated hydro-limited timestep at level 0: 1.27342375e-07 ...hydro-limited CFL timestep constrained at (i) = (308) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.27342375e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000926209 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.066545295 ...estimated hydro-limited timestep at level 0: 1.277380243e-07 ...hydro-limited CFL timestep constrained at (i) = (308) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.277380243e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.008580742652 [Level 0 step 14] Advanced 1024 cells TIME= 3.136810664e-07 MASS = 3.2768e+13 TIME= 3.136810664e-07 XMOM = 1.105148838e+19 TIME= 3.136810664e-07 YMOM = 0 TIME= 3.136810664e-07 ZMOM = 0 TIME= 3.136810664e-07 ANG MOM X = 0 TIME= 3.136810664e-07 ANG MOM Y = 0 TIME= 3.136810664e-07 ANG MOM Z = 0 TIME= 3.136810664e-07 RHO*e = 2.590394724e+31 TIME= 3.136810664e-07 RHO*K = 3.963368745e+26 TIME= 3.136810664e-07 RHO*E = 2.590434358e+31 TIME= 3.136810664e-07 CENTER OF MASS X-LOC = 81920.0628 TIME= 3.136810664e-07 CENTER OF MASS X-VEL = 337264.6601 TIME= 3.136810664e-07 CENTER OF MASS Y-LOC = 0 TIME= 3.136810664e-07 CENTER OF MASS Y-VEL = 0 TIME= 3.136810664e-07 CENTER OF MASS Z-LOC = 0 TIME= 3.136810664e-07 CENTER OF MASS Z-VEL = 0 TIME= 3.136810664e-07 MAXIMUM TEMPERATURE = 6813053119 TIME= 3.136810664e-07 MAXIMUM DENSITY = 218742986.2 TIME= 3.136810664e-07 MAXIMUM T_S / T_E = 1.818198698 [STEP 14] Coarse TimeStep time: 0.120882927 [STEP 14] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 14 TIME = 3.136810664e-07 DT = 3.018029188e-08 ...estimated hydro-limited timestep at level 0: 1.277380243e-07 ...hydro-limited CFL timestep constrained at (i) = (308) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.277380243e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.277380243e-07 ... but limiting to: 3.168930648e-08 = 1.05 * 3.018029188e-08 [Level 0 step 15] ADVANCE with dt = 3.168930648e-08  Beginning subcycle 1 starting at time 3.136810664e-07 with dt = 3.168930648e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000822821 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.045545565 ...estimated hydro-limited timestep at level 0: 1.277609861e-07 ...hydro-limited CFL timestep constrained at (i) = (308) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.277609861e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000832242 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.045139259 ...estimated hydro-limited timestep at level 0: 1.270323981e-07 ...hydro-limited CFL timestep constrained at (i) = (308) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.270323981e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.01059730784 [Level 0 step 15] Advanced 1024 cells TIME= 3.453703729e-07 MASS = 3.2768e+13 TIME= 3.453703729e-07 XMOM = 1.238852147e+19 TIME= 3.453703729e-07 YMOM = 0 TIME= 3.453703729e-07 ZMOM = 0 TIME= 3.453703729e-07 ANG MOM X = 0 TIME= 3.453703729e-07 ANG MOM Y = 0 TIME= 3.453703729e-07 ANG MOM Z = 0 TIME= 3.453703729e-07 RHO*e = 2.601798192e+31 TIME= 3.453703729e-07 RHO*K = 4.757490889e+26 TIME= 3.453703729e-07 RHO*E = 2.601845767e+31 TIME= 3.453703729e-07 CENTER OF MASS X-LOC = 81920.07713 TIME= 3.453703729e-07 CENTER OF MASS X-VEL = 378067.6718 TIME= 3.453703729e-07 CENTER OF MASS Y-LOC = 0 TIME= 3.453703729e-07 CENTER OF MASS Y-VEL = 0 TIME= 3.453703729e-07 CENTER OF MASS Z-LOC = 0 TIME= 3.453703729e-07 CENTER OF MASS Z-VEL = 0 TIME= 3.453703729e-07 MAXIMUM TEMPERATURE = 6794163856 TIME= 3.453703729e-07 MAXIMUM DENSITY = 222111742.1 TIME= 3.453703729e-07 MAXIMUM T_S / T_E = 0.1990732622 [STEP 15] Coarse TimeStep time: 0.098176655 [STEP 15] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 15 TIME = 3.453703729e-07 DT = 3.168930648e-08 ...estimated hydro-limited timestep at level 0: 1.270323981e-07 ...hydro-limited CFL timestep constrained at (i) = (308) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.270323981e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.270323981e-07 ... but limiting to: 3.32737718e-08 = 1.05 * 3.168930648e-08 [Level 0 step 16] ADVANCE with dt = 3.32737718e-08  Beginning subcycle 1 starting at time 3.453703729e-07 with dt = 3.32737718e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000832215 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.041344698 ...estimated hydro-limited timestep at level 0: 1.266286034e-07 ...hydro-limited CFL timestep constrained at (i) = (308) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.266286034e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000893024 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.041015145 ...estimated hydro-limited timestep at level 0: 1.26615372e-07 ...hydro-limited CFL timestep constrained at (i) = (308) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.26615372e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.01157568063 [Level 0 step 16] Advanced 1024 cells TIME= 3.786441447e-07 MASS = 3.2768e+13 TIME= 3.786441447e-07 XMOM = 1.38211407e+19 TIME= 3.786441447e-07 YMOM = 0 TIME= 3.786441447e-07 ZMOM = 0 TIME= 3.786441447e-07 ANG MOM X = 0 TIME= 3.786441447e-07 ANG MOM Y = 0 TIME= 3.786441447e-07 ANG MOM Z = 0 TIME= 3.786441447e-07 RHO*e = 2.613150427e+31 TIME= 3.786441447e-07 RHO*K = 5.699506063e+26 TIME= 3.786441447e-07 RHO*E = 2.613207422e+31 TIME= 3.786441447e-07 CENTER OF MASS X-LOC = 81920.09326 TIME= 3.786441447e-07 CENTER OF MASS X-VEL = 421787.7411 TIME= 3.786441447e-07 CENTER OF MASS Y-LOC = 0 TIME= 3.786441447e-07 CENTER OF MASS Y-VEL = 0 TIME= 3.786441447e-07 CENTER OF MASS Z-LOC = 0 TIME= 3.786441447e-07 CENTER OF MASS Z-VEL = 0 TIME= 3.786441447e-07 MAXIMUM TEMPERATURE = 6779843916 TIME= 3.786441447e-07 MAXIMUM DENSITY = 223813295.4 TIME= 3.786441447e-07 MAXIMUM T_S / T_E = 0.1563725361 [STEP 16] Coarse TimeStep time: 0.090008456 [STEP 16] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 16 TIME = 3.786441447e-07 DT = 3.32737718e-08 ...estimated hydro-limited timestep at level 0: 1.26615372e-07 ...hydro-limited CFL timestep constrained at (i) = (308) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.26615372e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.26615372e-07 ... but limiting to: 3.493746039e-08 = 1.05 * 3.32737718e-08 [Level 0 step 17] ADVANCE with dt = 3.493746039e-08  Beginning subcycle 1 starting at time 3.786441447e-07 with dt = 3.493746039e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000829026 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.048313462 ...estimated hydro-limited timestep at level 0: 1.266125966e-07 ...hydro-limited CFL timestep constrained at (i) = (308) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.266125966e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000916147 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.049101826 ...estimated hydro-limited timestep at level 0: 1.27140613e-07 ...hydro-limited CFL timestep constrained at (i) = (308) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.27140613e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.009881081665 [Level 0 step 17] Advanced 1024 cells TIME= 4.135816051e-07 MASS = 3.2768e+13 TIME= 4.135816051e-07 XMOM = 1.535528316e+19 TIME= 4.135816051e-07 YMOM = 0 TIME= 4.135816051e-07 ZMOM = 0 TIME= 4.135816051e-07 ANG MOM X = 0 TIME= 4.135816051e-07 ANG MOM Y = 0 TIME= 4.135816051e-07 ANG MOM Z = 0 TIME= 4.135816051e-07 RHO*e = 2.624670794e+31 TIME= 4.135816051e-07 RHO*K = 6.645632972e+26 TIME= 4.135816051e-07 RHO*E = 2.62473725e+31 TIME= 4.135816051e-07 CENTER OF MASS X-LOC = 81920.11112 TIME= 4.135816051e-07 CENTER OF MASS X-VEL = 468606.0535 TIME= 4.135816051e-07 CENTER OF MASS Y-LOC = 0 TIME= 4.135816051e-07 CENTER OF MASS Y-VEL = 0 TIME= 4.135816051e-07 CENTER OF MASS Z-LOC = 0 TIME= 4.135816051e-07 CENTER OF MASS Z-VEL = 0 TIME= 4.135816051e-07 MAXIMUM TEMPERATURE = 6773235516 TIME= 4.135816051e-07 MAXIMUM DENSITY = 221988284.6 TIME= 4.135816051e-07 MAXIMUM T_S / T_E = 0.4935899253 [STEP 17] Coarse TimeStep time: 0.105226209 [STEP 17] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 17 TIME = 4.135816051e-07 DT = 3.493746039e-08 ...estimated hydro-limited timestep at level 0: 1.27140613e-07 ...hydro-limited CFL timestep constrained at (i) = (308) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.27140613e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.27140613e-07 ... but limiting to: 3.668433341e-08 = 1.05 * 3.493746039e-08 [Level 0 step 18] ADVANCE with dt = 3.668433341e-08  Beginning subcycle 1 starting at time 4.135816051e-07 with dt = 3.668433341e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000831453 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.048111106 ...estimated hydro-limited timestep at level 0: 1.238741157e-07 ...hydro-limited CFL timestep constrained at (i) = (309) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.238741157e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000942153 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.047408575 ...estimated hydro-limited timestep at level 0: 1.243512822e-07 ...hydro-limited CFL timestep constrained at (i) = (309) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.243512822e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.01007742672 [Level 0 step 18] Advanced 1024 cells TIME= 4.502659385e-07 MASS = 3.2768e+13 TIME= 4.502659385e-07 XMOM = 1.699728686e+19 TIME= 4.502659385e-07 YMOM = 0 TIME= 4.502659385e-07 ZMOM = 0 TIME= 4.502659385e-07 ANG MOM X = 0 TIME= 4.502659385e-07 ANG MOM Y = 0 TIME= 4.502659385e-07 ANG MOM Z = 0 TIME= 4.502659385e-07 RHO*e = 2.637022136e+31 TIME= 4.502659385e-07 RHO*K = 7.7520104e+26 TIME= 4.502659385e-07 RHO*E = 2.637099656e+31 TIME= 4.502659385e-07 CENTER OF MASS X-LOC = 81920.13066 TIME= 4.502659385e-07 CENTER OF MASS X-VEL = 518716.0298 TIME= 4.502659385e-07 CENTER OF MASS Y-LOC = 0 TIME= 4.502659385e-07 CENTER OF MASS Y-VEL = 0 TIME= 4.502659385e-07 CENTER OF MASS Z-LOC = 0 TIME= 4.502659385e-07 CENTER OF MASS Z-VEL = 0 TIME= 4.502659385e-07 MAXIMUM TEMPERATURE = 6770858758 TIME= 4.502659385e-07 MAXIMUM DENSITY = 225678510.2 TIME= 4.502659385e-07 MAXIMUM T_S / T_E = 1.29405688 [STEP 18] Coarse TimeStep time: 0.103244363 [STEP 18] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 18 TIME = 4.502659385e-07 DT = 3.668433341e-08 ...estimated hydro-limited timestep at level 0: 1.243512822e-07 ...hydro-limited CFL timestep constrained at (i) = (309) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.243512822e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.243512822e-07 ... but limiting to: 3.851855008e-08 = 1.05 * 3.668433341e-08 [Level 0 step 19] ADVANCE with dt = 3.851855008e-08  Beginning subcycle 1 starting at time 4.502659385e-07 with dt = 3.851855008e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000830905 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.051495292 ...estimated hydro-limited timestep at level 0: 1.243020066e-07 ...hydro-limited CFL timestep constrained at (i) = (309) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.243020066e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000925532 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.051403976 ...estimated hydro-limited timestep at level 0: 1.23513361e-07 ...hydro-limited CFL timestep constrained at (i) = (309) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.23513361e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.00938259269 [Level 0 step 19] Advanced 1024 cells TIME= 4.887844886e-07 MASS = 3.2768e+13 TIME= 4.887844886e-07 XMOM = 1.875389548e+19 TIME= 4.887844886e-07 YMOM = 0 TIME= 4.887844886e-07 ZMOM = 0 TIME= 4.887844886e-07 ANG MOM X = 0 TIME= 4.887844886e-07 ANG MOM Y = 0 TIME= 4.887844886e-07 ANG MOM Z = 0 TIME= 4.887844886e-07 RHO*e = 2.648394407e+31 TIME= 4.887844886e-07 RHO*K = 8.950695879e+26 TIME= 4.887844886e-07 RHO*E = 2.648483914e+31 TIME= 4.887844886e-07 CENTER OF MASS X-LOC = 81920.15591 TIME= 4.887844886e-07 CENTER OF MASS X-VEL = 572323.4705 TIME= 4.887844886e-07 CENTER OF MASS Y-LOC = 0 TIME= 4.887844886e-07 CENTER OF MASS Y-VEL = 0 TIME= 4.887844886e-07 CENTER OF MASS Z-LOC = 0 TIME= 4.887844886e-07 CENTER OF MASS Z-VEL = 0 TIME= 4.887844886e-07 MAXIMUM TEMPERATURE = 6766902530 TIME= 4.887844886e-07 MAXIMUM DENSITY = 229775772.9 TIME= 4.887844886e-07 MAXIMUM T_S / T_E = 0.1679166936 [STEP 19] Coarse TimeStep time: 0.110711304 [STEP 19] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 19 TIME = 4.887844886e-07 DT = 3.851855008e-08 ...estimated hydro-limited timestep at level 0: 1.23513361e-07 ...hydro-limited CFL timestep constrained at (i) = (309) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.23513361e-07 Castro::compute_new_dt : limiting dt at level 0 ... new dt computed: 1.23513361e-07 ... but limiting to: 4.044447758e-08 = 1.05 * 3.851855008e-08 [Level 0 step 20] ADVANCE with dt = 4.044447758e-08  Beginning subcycle 1 starting at time 4.887844886e-07 with dt = 4.044447758e-08 Estimated number of subcycles remaining: 1 Beginning SDC iteration 1 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000833258 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.047797942 ...estimated hydro-limited timestep at level 0: 1.232606181e-07 ...hydro-limited CFL timestep constrained at (i) = (309) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.232606181e-07 Ending SDC iteration 1 of 2. Beginning SDC iteration 2 of 2. ... Entering construct_ctu_hydro_source() ... Leaving construct_ctu_hydro_source() Castro::construct_ctu_hydro_source() time = 0.000924437 ... Entering burner and doing full timestep of burning. ... Leaving burner after completing full timestep of burning. Castro::react_state() time = 0.047350059 ...estimated hydro-limited timestep at level 0: 1.233404626e-07 ...hydro-limited CFL timestep constrained at (i) = (309) Castro::estTimeStep (hydro-limited) at level 0: estdt = 1.233404626e-07 Ending SDC iteration 2 of 2.  Subcycle completed Subcycling complete Zones advanced per microsecond at this level: 0.01010142063 [Level 0 step 20] Advanced 1024 cells TIME= 5.292289662e-07 MASS = 3.2768e+13 TIME= 5.292289662e-07 XMOM = 2.063226413e+19 TIME= 5.292289662e-07 YMOM = 0 TIME= 5.292289662e-07 ZMOM = 0 TIME= 5.292289662e-07 ANG MOM X = 0 TIME= 5.292289662e-07 ANG MOM Y = 0 TIME= 5.292289662e-07 ANG MOM Z = 0 TIME= 5.292289662e-07 RHO*e = 2.659873825e+31 TIME= 5.292289662e-07 RHO*K = 1.035061454e+27 TIME= 5.292289662e-07 RHO*E = 2.659977331e+31 TIME= 5.292289662e-07 CENTER OF MASS X-LOC = 81920.18379 TIME= 5.292289662e-07 CENTER OF MASS X-VEL = 629646.7326 TIME= 5.292289662e-07 CENTER OF MASS Y-LOC = 0 TIME= 5.292289662e-07 CENTER OF MASS Y-VEL = 0 TIME= 5.292289662e-07 CENTER OF MASS Z-LOC = 0 TIME= 5.292289662e-07 CENTER OF MASS Z-VEL = 0 TIME= 5.292289662e-07 MAXIMUM TEMPERATURE = 6756603409 TIME= 5.292289662e-07 MAXIMUM DENSITY = 231116839.9 TIME= 5.292289662e-07 MAXIMUM T_S / T_E = 0.3136665492 [STEP 20] Coarse TimeStep time: 0.102954446 [STEP 20] FAB kilobyte spread across MPI nodes: [843 ... 843] STEP = 20 TIME = 5.292289662e-07 DT = 4.044447758e-08 PLOTFILE: file = Detonation-SDC_plt00020 Write plotfile time = 0.011064865 seconds Ending run at 05:03:26 UTC on 2023-04-27. Run time = 3.884340775 Run time without initialization = 2.639516177 Average number of zones advanced per microsecond: 0.008 Average number of zones advanced per microsecond per rank: 0.002 TinyProfiler total time across processes [min...avg...max]: 3.884 ... 3.884 ... 3.884 ------------------------------------------------------------------------------------------- Name NCalls Excl. Min Excl. Avg Excl. Max Max % ------------------------------------------------------------------------------------------- Castro::react_state() 40 2.4637 2.4649 2.4655 63.47% Amr::InitAmr() 1 1.228 1.229 1.229 31.64% Castro::computeTemp() 163 0.02829 0.03367 0.04658 1.20% Castro::construct_ctu_hydro_source() 40 0.02753 0.02977 0.03491 0.90% Castro::estTimeStep() 61 0.01598 0.0279 0.03285 0.85% Castro::reset_internal_energy(Fab) 163 0.01535 0.01635 0.01878 0.48% Castro::sum_integrated_quantities() 21 0.01072 0.01251 0.01323 0.34% Castro::do_advance_ctu() 40 0.00137 0.007556 0.01182 0.30% Amr::writePlotFile() 2 0.005743 0.009688 0.01108 0.29% VisMF::Write(FabArray) 2 0.003628 0.004794 0.008171 0.21% FabArray::ParallelCopy_finish() 574 0.001938 0.005619 0.008038 0.21% Castro::normalize_species() 162 0.005982 0.006341 0.006744 0.17% amrex::Copy() 1024 0.004984 0.005249 0.00583 0.15% FabArray::setDomainBndry() 454 0.005162 0.005536 0.005793 0.15% Castro::derive() 178 0.004901 0.005149 0.005686 0.15% FabArray::ParallelCopy_nowait() 454 0.002759 0.003125 0.003477 0.09% Castro::volWgtSum() 609 0.002902 0.003062 0.003396 0.09% StateDataPhysBCFunct::() 454 0.001836 0.001973 0.002197 0.06% FabArray::setVal() 293 0.001805 0.001862 0.002005 0.05% Amr::coarseTimeStep() 20 0.001045 0.0017 0.001976 0.05% MultiFab::contains_nan() 120 0.001164 0.001309 0.001684 0.04% FillPatchIterator::Initialize 454 0.001504 0.00157 0.001675 0.04% Castro::enforce_min_density() 162 0.0008421 0.001001 0.00141 0.04% Castro::subcycle_advance_ctu() 20 0.0001277 0.0003805 0.001118 0.03% Castro::reset_internal_energy(MultiFab) 163 0.0008334 0.0008689 0.0009454 0.02% DistributionMapping::LeastUsedCPUs() 1 1.331e-05 0.0003156 0.0005861 0.02% Castro::computeNewDt() 19 1.092e-05 0.0001249 0.00046 0.01% Castro::finalize_advance() 20 0.0002989 0.0003314 0.0004147 0.01% Castro::locWgtSum() 63 0.0003095 0.0003316 0.0003649 0.01% FillPatchSingleLevel 454 0.0002437 0.0002871 0.0003476 0.01% StateData::FillBoundary(geom) 66 0 0.0001352 0.0003144 0.01% main() 1 0.0002604 0.0002767 0.0003055 0.01% FabArray::ParallelCopy() 454 0.0002217 0.0002402 0.0002695 0.01% Amr::timeStep() 20 0.0001428 0.0001704 0.0002495 0.01% Castro::initialize_do_advance() 40 0.0002127 0.0002296 0.000244 0.01% Castro::clean_state() 162 0.0001402 0.000169 0.0002372 0.01% Castro::initData() 1 0.0001517 0.0001769 0.0001915 0.00% Castro::initMFs() 1 0.0001453 0.0001528 0.0001641 0.00% StateData::define() 4 7.696e-05 9.254e-05 0.0001325 0.00% Amr::defBaseLevel() 1 0.0001052 0.0001108 0.0001207 0.00% Castro::initialize_advance() 20 0.0001031 0.0001122 0.0001207 0.00% Castro::expand_state() 40 8.527e-05 9.333e-05 0.0001033 0.00% Castro::finalize_do_advance() 40 5.349e-05 5.929e-05 6.733e-05 0.00% Castro::check_for_nan() 120 4.621e-05 5.299e-05 6.718e-05 0.00% Castro::enforce_speed_limit() 162 4.599e-05 5.143e-05 6.656e-05 0.00% Castro::buildMetrics() 1 1.991e-05 3.286e-05 6.225e-05 0.00% FabArrayBase::getCPC() 132 5.061e-05 5.568e-05 5.817e-05 0.00% Amr::writeSmallPlotFile() 1 3.427e-05 4.344e-05 5.293e-05 0.00% Amr::FinalizeInit() 1 1.73e-06 1.325e-05 4.662e-05 0.00% Castro::swap_state_time_levels() 20 2.93e-05 3.278e-05 3.849e-05 0.00% Castro::advance() 20 3.04e-05 3.279e-05 3.531e-05 0.00% Castro::post_timestep() 20 2.037e-05 2.31e-05 2.61e-05 0.00% FabArrayBase::CPC::define() 2 9.476e-06 1.286e-05 1.634e-05 0.00% AmrLevel::AmrLevel(dm) 1 1.065e-05 1.306e-05 1.591e-05 0.00% Castro::create_source_corrector() 40 1.187e-05 1.304e-05 1.455e-05 0.00% Castro::FluxRegCrseInit 20 7.21e-06 1.144e-05 1.347e-05 0.00% DistributionMapping::SFCProcessorMapDoIt() 1 3.492e-06 6.571e-06 1.19e-05 0.00% Amr::initSubcycle() 1 9.865e-06 1.072e-05 1.183e-05 0.00% Castro::Castro() 1 7.933e-06 8.929e-06 1.078e-05 0.00% Castro::retry_advance_ctu() 20 5.366e-06 6.273e-06 7.424e-06 0.00% Amr::InitializeInit() 1 2.534e-06 3.933e-06 7.054e-06 0.00% Castro::FluxRegFineAdd() 20 3.812e-06 4.918e-06 5.783e-06 0.00% Castro::enforce_consistent_e() 1 4.007e-06 4.787e-06 5.483e-06 0.00% Castro::computeInitialDt() 2 1.61e-06 2.154e-06 2.664e-06 0.00% Amr::init() 1 1.391e-06 1.825e-06 2.467e-06 0.00% Amr::initialInit() 1 9.07e-07 1.289e-06 1.597e-06 0.00% Castro::post_regrid() 1 1.066e-06 1.21e-06 1.359e-06 0.00% DistributionMapping::Distribute() 1 7.69e-07 1.009e-06 1.195e-06 0.00% Castro::post_init() 1 7.47e-07 9.193e-07 1.176e-06 0.00% ------------------------------------------------------------------------------------------- ------------------------------------------------------------------------------------------- Name NCalls Incl. Min Incl. Avg Incl. Max Max % ------------------------------------------------------------------------------------------- main() 1 3.884 3.884 3.884 100.00% Amr::coarseTimeStep() 20 2.628 2.628 2.628 67.66% Amr::timeStep() 20 2.621 2.622 2.622 67.50% Castro::advance() 20 2.595 2.595 2.595 66.81% Castro::subcycle_advance_ctu() 20 2.586 2.587 2.587 66.61% Castro::do_advance_ctu() 40 2.585 2.587 2.587 66.61% Castro::react_state() 40 2.471 2.472 2.472 63.65% Amr::InitAmr() 1 1.228 1.229 1.229 31.64% Castro::clean_state() 162 0.05123 0.05817 0.07432 1.91% Castro::computeTemp() 163 0.04448 0.05089 0.0663 1.71% Castro::construct_ctu_hydro_source() 40 0.02753 0.02977 0.03491 0.90% Castro::estTimeStep() 61 0.01598 0.0279 0.03285 0.85% Castro::post_timestep() 20 0.02611 0.02627 0.02648 0.68% Amr::writePlotFile() 2 0.02366 0.02373 0.02376 0.61% FillPatchIterator::Initialize 454 0.01776 0.02005 0.02189 0.56% Castro::sum_integrated_quantities() 21 0.01975 0.02057 0.02095 0.54% Castro::reset_internal_energy(MultiFab) 163 0.01619 0.01722 0.01972 0.51% Castro::reset_internal_energy(Fab) 163 0.01535 0.01635 0.01878 0.48% Castro::initialize_do_advance() 40 0.01578 0.01745 0.01822 0.47% Amr::init() 1 0.01569 0.01601 0.0163 0.42% FillPatchSingleLevel 454 0.0103 0.01294 0.01503 0.39% Castro::derive() 178 0.0126 0.01308 0.01404 0.36% FabArray::ParallelCopy() 454 0.007437 0.01055 0.01285 0.33% FabArray::ParallelCopy_nowait() 454 0.006236 0.00761 0.01068 0.27% Castro::initialize_advance() 20 0.007216 0.007641 0.008646 0.22% VisMF::Write(FabArray) 2 0.003628 0.004794 0.008171 0.21% FabArray::ParallelCopy_finish() 574 0.001938 0.005619 0.008038 0.21% Castro::normalize_species() 162 0.005982 0.006341 0.006744 0.17% amrex::Copy() 1024 0.004984 0.005249 0.00583 0.15% FabArray::setDomainBndry() 454 0.005162 0.005536 0.005793 0.15% Castro::computeNewDt() 19 0.004598 0.004735 0.005121 0.13% Castro::expand_state() 40 0.002543 0.003794 0.004962 0.13% Amr::initialInit() 1 0.003074 0.003418 0.00378 0.10% Castro::volWgtSum() 609 0.002902 0.003062 0.003396 0.09% StateDataPhysBCFunct::() 454 0.001836 0.002108 0.002511 0.06% Amr::InitializeInit() 1 0.001366 0.001701 0.002099 0.05% Amr::defBaseLevel() 1 0.001363 0.001697 0.002092 0.05% FabArray::setVal() 293 0.001805 0.001862 0.002005 0.05% Amr::FinalizeInit() 1 0.001677 0.001716 0.001799 0.05% Castro::check_for_nan() 120 0.001214 0.001362 0.001751 0.05% MultiFab::contains_nan() 120 0.001164 0.001309 0.001684 0.04% Castro::enforce_min_density() 162 0.0008421 0.001001 0.00141 0.04% Castro::post_init() 1 0.0009306 0.0009608 0.0009754 0.03% Castro::initData() 1 0.0008255 0.0008931 0.0009387 0.02% Castro::computeInitialDt() 2 0.0005535 0.000658 0.0007607 0.02% DistributionMapping::SFCProcessorMapDoIt() 1 1.757e-05 0.0003231 0.0005991 0.02% DistributionMapping::LeastUsedCPUs() 1 1.331e-05 0.0003156 0.0005861 0.02% Castro::finalize_advance() 20 0.0004034 0.0004522 0.0005447 0.01% Castro::locWgtSum() 63 0.0003095 0.0003316 0.0003649 0.01% Castro::post_regrid() 1 0.0003104 0.0003377 0.0003593 0.01% Castro::Castro() 1 0.0002436 0.0002647 0.0003145 0.01% StateData::FillBoundary(geom) 66 0 0.0001352 0.0003144 0.01% Castro::initMFs() 1 0.0001496 0.0001574 0.0001691 0.00% AmrLevel::AmrLevel(dm) 1 8.761e-05 0.0001056 0.0001484 0.00% StateData::define() 4 7.696e-05 9.254e-05 0.0001325 0.00% Castro::buildMetrics() 1 6.037e-05 7.154e-05 9.963e-05 0.00% FabArrayBase::getCPC() 132 6.654e-05 6.854e-05 7.165e-05 0.00% Castro::finalize_do_advance() 40 5.349e-05 5.929e-05 6.733e-05 0.00% Castro::enforce_speed_limit() 162 4.599e-05 5.143e-05 6.656e-05 0.00% Amr::writeSmallPlotFile() 1 3.427e-05 4.344e-05 5.293e-05 0.00% Castro::swap_state_time_levels() 20 2.93e-05 3.278e-05 3.849e-05 0.00% FabArrayBase::CPC::define() 2 9.476e-06 1.286e-05 1.634e-05 0.00% Castro::create_source_corrector() 40 1.187e-05 1.304e-05 1.455e-05 0.00% Castro::FluxRegCrseInit 20 7.21e-06 1.144e-05 1.347e-05 0.00% Amr::initSubcycle() 1 9.865e-06 1.072e-05 1.183e-05 0.00% Castro::retry_advance_ctu() 20 5.366e-06 6.273e-06 7.424e-06 0.00% Castro::FluxRegFineAdd() 20 3.812e-06 4.918e-06 5.783e-06 0.00% Castro::enforce_consistent_e() 1 4.007e-06 4.787e-06 5.483e-06 0.00% DistributionMapping::Distribute() 1 7.69e-07 1.009e-06 1.195e-06 0.00% ------------------------------------------------------------------------------------------- Unused ParmParse Variables: [TOP]::amr.ref_ratio(nvals = 4) :: [2, 2, 2, 2] [TOP]::amr.regrid_int(nvals = 4) :: [2, 2, 2, 2] Pinned Memory Usage: --------------------------------------------------------------------------------------------------------------------- Name Nalloc Nfree AvgMem min AvgMem avg AvgMem max MaxMem min MaxMem avg MaxMem max --------------------------------------------------------------------------------------------------------------------- The_Pinned_Arena::Initialize() 4 4 30 B 34 B 37 B 8192 KiB 8192 KiB 8192 KiB --------------------------------------------------------------------------------------------------------------------- AMReX (23.04-37-ga6e89ecc1175) finalized