MPI initialized with 16 MPI processes MPI initialized with thread support level 0 AMReX (23.03-1-gb96f6e5bd13d) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = 5peaks_const_grav.dat model file = 5peaks_const_grav.dat reading initial model 1000 points found in the initial model 10 variables found in the initial model WARNING: variable not found: gravity WARNING: variable not found: abar WARNING: variable not found: zbar WARNING: variable not found: gpot WARNING: variable not found: cno model file mapping, level: 0 dr of MAESTRO base state = 93750000.000000 dr of input file data = 10010010.010010 maximum radius (cell-centered) of input model = 10000000000.000000 WARNING: resolution of base state array is not an integer multiple of the initial model's resolution. make sure this is a desired property as this could lead to aliasing when performing the interpolation. modulus = 3659909.909910 setting r_cutoff to 105 radius at r_cutoff 9890625000 Maximum HSE Error = 0.054171 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile test_stability_pltInitData after InitData inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.018384263 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.000294124 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile test_stability_pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.015544378 Call to firstdt for level 0 gives dt_lev = 0.01907406555 Multiplying dt_lev by init_shrink; dt_lev = 0.001907406555 Minimum firstdt over all levels = 0.001907406555 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 4.945354899e-27 MLMG: Initial residual (resid0) = 4.945354899e-27 MLMG: Final Iter. 3 resid, resid/bnorm = 2.357566962e-30, 0.0004767235133 MLMG: Timers: Solve = 0.002767747 Iter = 0.002325042 Bottom = 9.4206e-05 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 1 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #2 Calling nodal solver MLMG: Initial rhs = 2.306075226e-30 MLMG: Initial residual (resid0) = 2.306075226e-30 MLMG: Final Iter. 5 resid, resid/bnorm = 1.933632021e-37, 8.384947719e-08 MLMG: Timers: Solve = 0.003477738 Iter = 0.003319348 Bottom = 0.000140972 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 2 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #3 Calling nodal solver MLMG: Initial rhs = 9.742172191e-32 MLMG: Initial residual (resid0) = 9.742172191e-32 MLMG: Final Iter. 4 resid, resid/bnorm = 7.521071013e-41, 7.720117101e-10 MLMG: Timers: Solve = 0.003521547 Iter = 0.003366259 Bottom = 0.000124197 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 3 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Writing plotfile test_stability_pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.018196192 Doing initial pressure iteration #1 Timestep 0 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.893547601e-20 MLMG: Initial residual (resid0) = 4.893547601e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 4.517319815e-31, 9.231175792e-12 MLMG: Timers: Solve = 0.006638555 Iter = 0.006196587 Bottom = 0.000154018 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.893547507e-20 MLMG: Initial residual (resid0) = 2.477484298e-27 MLMG: Final Iter. 4 resid, resid/bnorm = 4.813594311e-30, 9.836615062e-11 MLMG: Timers: Solve = 0.001780645 Iter = 0.001577736 Bottom = 6.86e-05 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.755411273e-17 MLMG: Initial residual (resid0) = 5.755411273e-17 MLMG: Final Iter. 9 resid, resid/bnorm = 1.02012041e-27, 1.772454411e-11 MLMG: Timers: Solve = 0.006353404 Iter = 0.006182273 Bottom = 0.000248183 Done calling nodal solver Timestep 0 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.006987028 seconds MAC Proj :0.009317772 seconds Nodal Proj :0.007294498 seconds Reactions :0.014825225 seconds Misc :0.002105578 seconds Base State :5.600031727e-08 seconds Time to advance time step: 0.04428787 Writing plotfile 0 after all initialization inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.014485363 Writing checkpoint 0 after all initialization Writing checkpoint chk0000000 Calling Evolve() Timestep 1 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.257776127e-26 MLMG: Initial residual (resid0) = 1.257776127e-26 MLMG: Final Iter. 10 resid, resid/bnorm = 1.092411925e-37, 8.685265223e-12 MLMG: Timers: Solve = 0.008465847 Iter = 0.007879452 Bottom = 0.000159575 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.257776127e-26 MLMG: Initial residual (resid0) = 1.092411925e-37 MLMG: No iterations needed MLMG: Timers: Solve = 0.000509887 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.097790919e-19 MLMG: Initial residual (resid0) = 1.097790919e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.945791097e-30, 1.772460551e-11 MLMG: Timers: Solve = 0.008712408 Iter = 0.008386171 Bottom = 0.000252614 Done calling nodal solver Timestep 1 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.010631434 seconds MAC Proj :0.010173125 seconds Nodal Proj :0.009955018 seconds Reactions :0.022273788 seconds Misc :0.002730646 seconds Base State :1.230000635e-07 seconds Time to advance time step: 0.062704335 Call to estdt for level 0 gives dt_lev = 7.191081337e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 2 gives dt =1e+20 dt_growth factor limits the new dt = 0.002002776883 Timestep 2 starts with TIME = 0.001907406555 DT = 0.002002776883 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.080398705e-27 MLMG: Initial residual (resid0) = 8.080398705e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 1.160441939e-37, 1.436119654e-11 MLMG: Timers: Solve = 0.007102436 Iter = 0.006712522 Bottom = 0.000154888 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.498306209e-27 MLMG: Initial residual (resid0) = 2.601349809e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 8.688832515e-37, 9.14777048e-11 MLMG: Timers: Solve = 0.007324815 Iter = 0.006952638 Bottom = 0.00017293 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.096671578e-19 MLMG: Initial residual (resid0) = 1.096671578e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.008844235e-29, 9.19914635e-11 MLMG: Timers: Solve = 0.008873047 Iter = 0.008597507 Bottom = 0.000249514 Done calling nodal solver Timestep 2 ends with TIME = 0.003910183437 DT = 0.002002776883 Timing summary: Advection :0.009449981 seconds MAC Proj :0.015293651 seconds Nodal Proj :0.009910664 seconds Reactions :0.019336403 seconds Misc :0.002193668 seconds Base State :1.100002009e-07 seconds Time to advance time step: 0.056394206 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 3 gives dt =1e+20 dt_growth factor limits the new dt = 0.002102915727 Timestep 3 starts with TIME = 0.003910183437 DT = 0.002102915727 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 8.320997544e-21 MLMG: Final Iter. 10 resid, resid/bnorm = 7.676109766e-31, 9.22498742e-11 MLMG: Timers: Solve = 0.004831654 Iter = 0.004595798 Bottom = 0.000153463 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 7.676109766e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000232996 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.21031446e-19 MLMG: Initial residual (resid0) = 1.21031446e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.145209106e-30, 1.772439458e-11 MLMG: Timers: Solve = 0.006189912 Iter = 0.006022803 Bottom = 0.000244616 Done calling nodal solver Timestep 3 ends with TIME = 0.006013099164 DT = 0.002102915727 Timing summary: Advection :0.006031919001 seconds MAC Proj :0.005738289 seconds Nodal Proj :0.006946856 seconds Reactions :0.014097019 seconds Misc :0.001609194001 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.034607616 Call to estdt for level 0 gives dt_lev = 6.528630569e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 4 gives dt =1e+20 dt_growth factor limits the new dt = 0.002208061513 Timestep 4 starts with TIME = 0.006013099164 DT = 0.002208061513 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.308039747e-29 MLMG: Initial residual (resid0) = 1.308039747e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.129752045e-39, 8.636985596e-11 MLMG: Timers: Solve = 0.005081232 Iter = 0.004839814 Bottom = 0.000154683 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.308039747e-29 MLMG: Initial residual (resid0) = 1.129752045e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000210391 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.270830183e-19 MLMG: Initial residual (resid0) = 1.270830183e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.252495441e-30, 1.772459822e-11 MLMG: Timers: Solve = 0.00669556 Iter = 0.006493504 Bottom = 0.000246069 Done calling nodal solver Timestep 4 ends with TIME = 0.008221160677 DT = 0.002208061513 Timing summary: Advection :0.005783159 seconds MAC Proj :0.005930555 seconds Nodal Proj :0.00747635 seconds Reactions :0.012100044 seconds Misc :0.001605331001 seconds Base State :9.800032785e-08 seconds Time to advance time step: 0.033091892 Call to estdt for level 0 gives dt_lev = 6.226258359e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 5 gives dt =1e+20 dt_growth factor limits the new dt = 0.002318464589 Timestep 5 starts with TIME = 0.008221160677 DT = 0.002318464589 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.295923274e-30 MLMG: Initial residual (resid0) = 3.295923274e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.024366424e-40, 9.176082608e-11 MLMG: Timers: Solve = 0.004344275 Iter = 0.004117673 Bottom = 0.000158347 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.295923274e-30 MLMG: Initial residual (resid0) = 3.024366424e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000212898 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.334371692e-19 MLMG: Initial residual (resid0) = 1.334371692e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.365138268e-30, 1.772473353e-11 MLMG: Timers: Solve = 0.006206956 Iter = 0.006034911 Bottom = 0.000244611 Done calling nodal solver Timestep 5 ends with TIME = 0.01053962527 DT = 0.002318464589 Timing summary: Advection :0.006062188 seconds MAC Proj :0.005262239 seconds Nodal Proj :0.00693993 seconds Reactions :0.01414535 seconds Misc :0.001750586001 seconds Base State :1.240000529e-07 seconds Time to advance time step: 0.034349793 Call to estdt for level 0 gives dt_lev = 5.915049504e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 6 gives dt =1e+20 dt_growth factor limits the new dt = 0.002434387818 Timestep 6 starts with TIME = 0.01053962527 DT = 0.002434387818 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.377753945e-30 MLMG: Initial residual (resid0) = 3.377753945e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.175503469e-40, 9.401227921e-11 MLMG: Timers: Solve = 0.004366298 Iter = 0.004161116 Bottom = 0.000154543 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.377753945e-30 MLMG: Initial residual (resid0) = 3.175499966e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000198924 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.401090277e-19 MLMG: Initial residual (resid0) = 1.401090277e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.483342219e-30, 1.772435552e-11 MLMG: Timers: Solve = 0.006121717 Iter = 0.005943844 Bottom = 0.000247151 Done calling nodal solver Timestep 6 ends with TIME = 0.01297401308 DT = 0.002434387818 Timing summary: Advection :0.005887851999 seconds MAC Proj :0.005203883 seconds Nodal Proj :0.006876525 seconds Reactions :0.013067878 seconds Misc :0.002013904 seconds Base State :5.399988368e-08 seconds Time to advance time step: 0.033259035 Call to estdt for level 0 gives dt_lev = 5.625515433e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 7 gives dt =1e+20 dt_growth factor limits the new dt = 0.002556107209 Timestep 7 starts with TIME = 0.01297401308 DT = 0.002556107209 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.543159178e-30 MLMG: Initial residual (resid0) = 3.543159178e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.334123449e-40, 9.410030095e-11 MLMG: Timers: Solve = 0.004984183 Iter = 0.004790469 Bottom = 0.000156179 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.543159178e-30 MLMG: Initial residual (resid0) = 3.334123449e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000203561 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.471144791e-19 MLMG: Initial residual (resid0) = 1.471144791e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.607516552e-30, 1.772440461e-11 MLMG: Timers: Solve = 0.006783651 Iter = 0.006616324 Bottom = 0.000248945 Done calling nodal solver Timestep 7 ends with TIME = 0.01553012029 DT = 0.002556107209 Timing summary: Advection :0.005931593 seconds MAC Proj :0.005849141 seconds Nodal Proj :0.007691547 seconds Reactions :0.01201382 seconds Misc :0.001620065 seconds Base State :4.260000424e-07 seconds Time to advance time step: 0.033334193 Call to estdt for level 0 gives dt_lev = 5.353255202e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 8 gives dt =1e+20 dt_growth factor limits the new dt = 0.002683912569 Timestep 8 starts with TIME = 0.01553012029 DT = 0.002683912569 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.720271341e-30 MLMG: Initial residual (resid0) = 3.720271341e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.500226363e-40, 9.408524384e-11 MLMG: Timers: Solve = 0.010355223 Iter = 0.009928871 Bottom = 0.000157205 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.720271341e-30 MLMG: Initial residual (resid0) = 3.500226363e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00042038 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.54470203e-19 MLMG: Initial residual (resid0) = 1.54470203e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.737914046e-30, 1.772454488e-11 MLMG: Timers: Solve = 0.008701983 Iter = 0.008295192 Bottom = 0.000252247 Done calling nodal solver Timestep 8 ends with TIME = 0.01821403286 DT = 0.002683912569 Timing summary: Advection :0.011296727 seconds MAC Proj :0.01195287 seconds Nodal Proj :0.009881020001 seconds Reactions :0.022185673 seconds Misc :0.002740494 seconds Base State :6.700020094e-08 seconds Time to advance time step: 0.058346899 Call to estdt for level 0 gives dt_lev = 5.095618567e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 9 gives dt =1e+20 dt_growth factor limits the new dt = 0.002818108198 Timestep 9 starts with TIME = 0.01821403286 DT = 0.002818108198 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.90613533e-30 MLMG: Initial residual (resid0) = 3.90613533e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.675781034e-40, 9.410275692e-11 MLMG: Timers: Solve = 0.006562589 Iter = 0.00616806 Bottom = 0.000155845 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.90613533e-30 MLMG: Initial residual (resid0) = 3.675781034e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000472197 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.621937132e-19 MLMG: Initial residual (resid0) = 1.621937132e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.874835628e-30, 1.772470444e-11 MLMG: Timers: Solve = 0.006641312 Iter = 0.006433432 Bottom = 0.00025328 Done calling nodal solver Timestep 9 ends with TIME = 0.02103214106 DT = 0.002818108198 Timing summary: Advection :0.009252011 seconds MAC Proj :0.0079019 seconds Nodal Proj :0.007395264 seconds Reactions :0.020794735 seconds Misc :0.002687181 seconds Base State :6.29997885e-08 seconds Time to advance time step: 0.048202109 Call to estdt for level 0 gives dt_lev = 4.851290067e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 10 gives dt =1e+20 dt_growth factor limits the new dt = 0.002959013608 Timestep 10 starts with TIME = 0.02103214106 DT = 0.002959013608 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.101240383e-30 MLMG: Initial residual (resid0) = 4.101240383e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.859393172e-40, 9.410307155e-11 MLMG: Timers: Solve = 0.004604574 Iter = 0.004354685 Bottom = 0.000160491 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.101240383e-30 MLMG: Initial residual (resid0) = 3.859393172e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000247128 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.703033988e-19 MLMG: Initial residual (resid0) = 1.703033988e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.174814859e-29, 6.898364135e-11 MLMG: Timers: Solve = 0.006400336 Iter = 0.006204989 Bottom = 0.000253173 Done calling nodal solver Timestep 10 ends with TIME = 0.02399115467 DT = 0.002959013608 Timing summary: Advection :0.006230881001 seconds MAC Proj :0.005484099 seconds Nodal Proj :0.007127015 seconds Reactions :0.013073683 seconds Misc :0.001463989 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.033516338 Call to estdt for level 0 gives dt_lev = 1.153498162e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 11 gives dt =1e+20 dt_growth factor limits the new dt = 0.003106964288 Timestep 11 starts with TIME = 0.02399115467 DT = 0.003106964288 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 1.271430598e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.310137768e-31, 4.963021794e-11 MLMG: Timers: Solve = 0.004335155 Iter = 0.004117144 Bottom = 0.000159055 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 6.310137768e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000200795 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.788185688e-19 MLMG: Initial residual (resid0) = 1.788185688e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.169478835e-30, 1.772455096e-11 MLMG: Timers: Solve = 0.006187203 Iter = 0.006031179 Bottom = 0.000260622 Done calling nodal solver Timestep 11 ends with TIME = 0.02709811896 DT = 0.003106964288 Timing summary: Advection :0.005437878 seconds MAC Proj :0.00514606 seconds Nodal Proj :0.006870744 seconds Reactions :0.012034701 seconds Misc :0.001359683 seconds Base State :5.49998731e-08 seconds Time to advance time step: 0.031007404 Call to estdt for level 0 gives dt_lev = 4.376664086e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 12 gives dt =1e+20 dt_growth factor limits the new dt = 0.003262312503 Timestep 12 starts with TIME = 0.02709811896 DT = 0.003262312503 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.931483508e-30 MLMG: Initial residual (resid0) = 2.931483508e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.211723667e-40, 7.544724916e-11 MLMG: Timers: Solve = 0.004287495 Iter = 0.004098685 Bottom = 0.000160515 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.931483508e-30 MLMG: Initial residual (resid0) = 2.211723667e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000210142 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.877594972e-19 MLMG: Initial residual (resid0) = 1.877594972e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.328006944e-30, 1.772483945e-11 MLMG: Timers: Solve = 0.006340452 Iter = 0.00618039 Bottom = 0.000257501 Done calling nodal solver Timestep 12 ends with TIME = 0.03036043146 DT = 0.003262312503 Timing summary: Advection :0.005873922 seconds MAC Proj :0.005124781 seconds Nodal Proj :0.007023991 seconds Reactions :0.011886414 seconds Misc :0.001495038 seconds Base State :2.39000201e-07 seconds Time to advance time step: 0.03155141 Call to estdt for level 0 gives dt_lev = 4.177466111e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 13 gives dt =1e+20 dt_growth factor limits the new dt = 0.003425428128 Timestep 13 starts with TIME = 0.03036043146 DT = 0.003425428128 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.688771914e-30 MLMG: Initial residual (resid0) = 4.688771914e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.468299394e-40, 9.529786213e-11 MLMG: Timers: Solve = 0.004315321 Iter = 0.004066281 Bottom = 0.000160511 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.688771914e-30 MLMG: Initial residual (resid0) = 4.468299394e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000194124 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.971474721e-19 MLMG: Initial residual (resid0) = 1.971474721e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.494383217e-30, 1.772471734e-11 MLMG: Timers: Solve = 0.006299098 Iter = 0.006134659 Bottom = 0.00025567 Done calling nodal solver Timestep 13 ends with TIME = 0.03378585959 DT = 0.003425428128 Timing summary: Advection :0.006702936001 seconds MAC Proj :0.005115967 seconds Nodal Proj :0.006964105999 seconds Reactions :0.014850745 seconds Misc :0.001947932999 seconds Base State :5.89998308e-08 seconds Time to advance time step: 0.035724803 Call to estdt for level 0 gives dt_lev = 3.982280624e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 14 gives dt =1e+20 dt_growth factor limits the new dt = 0.003596699534 Timestep 14 starts with TIME = 0.03378585959 DT = 0.003596699534 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.983088965e-30 MLMG: Initial residual (resid0) = 4.983088965e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.691428148e-40, 9.414698756e-11 MLMG: Timers: Solve = 0.004982168 Iter = 0.004785118 Bottom = 0.000161646 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.983088965e-30 MLMG: Initial residual (resid0) = 4.691428148e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000201367 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.221658729e-19 MLMG: Initial residual (resid0) = 2.221658729e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.863249975e-30, 3.989474107e-11 MLMG: Timers: Solve = 0.00628197 Iter = 0.006108113 Bottom = 0.000253192 Done calling nodal solver Timestep 14 ends with TIME = 0.03738255912 DT = 0.003596699534 Timing summary: Advection :0.006074484 seconds MAC Proj :0.005932838 seconds Nodal Proj :0.007086911 seconds Reactions :0.01213426 seconds Misc :0.001424971001 seconds Base State :4.999992598e-08 seconds Time to advance time step: 0.032796325 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 15 gives dt =1e+20 dt_growth factor limits the new dt = 0.003776534511 Timestep 15 starts with TIME = 0.03738255912 DT = 0.003776534511 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 1.44706648e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 8.547886059e-31, 5.907044478e-11 MLMG: Timers: Solve = 0.004264732 Iter = 0.004068783 Bottom = 0.000158011 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 8.547886059e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000189772 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.279163939e-19 MLMG: Initial residual (resid0) = 2.279163939e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.500906095e-29, 6.585336268e-11 MLMG: Timers: Solve = 0.006244934 Iter = 0.006058747 Bottom = 0.000256752 Done calling nodal solver Timestep 15 ends with TIME = 0.04115909363 DT = 0.003776534511 Timing summary: Advection :0.005644158 seconds MAC Proj :0.005106362 seconds Nodal Proj :0.006943233 seconds Reactions :0.012947163 seconds Misc :0.001324804 seconds Base State :4.300000001e-08 seconds Time to advance time step: 0.032111798 Call to estdt for level 0 gives dt_lev = 9.044193233e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 16 gives dt =1e+20 dt_growth factor limits the new dt = 0.003965361236 Timestep 16 starts with TIME = 0.04115909363 DT = 0.003965361236 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 1.62270343e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.18702781e-31, 3.812790245e-11 MLMG: Timers: Solve = 0.004674617 Iter = 0.004470047 Bottom = 0.000159974 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 6.18702781e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000213282 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.282228424e-19 MLMG: Initial residual (resid0) = 2.282228424e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.045151033e-30, 1.772456688e-11 MLMG: Timers: Solve = 0.006289359 Iter = 0.006125979 Bottom = 0.000258868 Done calling nodal solver Timestep 16 ends with TIME = 0.04512445487 DT = 0.003965361236 Timing summary: Advection :0.005648522001 seconds MAC Proj :0.005518397 seconds Nodal Proj :0.007005155 seconds Reactions :0.013423436 seconds Misc :0.001540209 seconds Base State :4.69999577e-08 seconds Time to advance time step: 0.033283711 Call to estdt for level 0 gives dt_lev = 3.436593485e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 17 gives dt =1e+20 dt_growth factor limits the new dt = 0.004163629298 Timestep 17 starts with TIME = 0.04512445487 DT = 0.004163629298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.754694364e-30 MLMG: Initial residual (resid0) = 3.754694364e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.825939058e-40, 7.526415691e-11 MLMG: Timers: Solve = 0.004305181 Iter = 0.004117048 Bottom = 0.000169152 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.754694364e-30 MLMG: Initial residual (resid0) = 2.825939058e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000190104 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.396339845e-19 MLMG: Initial residual (resid0) = 2.396339845e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.247301455e-30, 1.772411982e-11 MLMG: Timers: Solve = 0.006207937 Iter = 0.006046143 Bottom = 0.000262133 Done calling nodal solver Timestep 17 ends with TIME = 0.04928808417 DT = 0.004163629298 Timing summary: Advection :0.005827924 seconds MAC Proj :0.005141865 seconds Nodal Proj :0.006930711 seconds Reactions :0.012188452 seconds Misc :0.001514381 seconds Base State :5.600031727e-08 seconds Time to advance time step: 0.031760639 Call to estdt for level 0 gives dt_lev = 3.276898941e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 18 gives dt =1e+20 dt_growth factor limits the new dt = 0.004371810763 Timestep 18 starts with TIME = 0.04928808417 DT = 0.004371810763 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.989009514e-30 MLMG: Initial residual (resid0) = 5.989009514e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.702479003e-40, 9.521572791e-11 MLMG: Timers: Solve = 0.004306538 Iter = 0.004122944 Bottom = 0.000167376 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.989009514e-30 MLMG: Initial residual (resid0) = 5.702479003e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000191398 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.516156837e-19 MLMG: Initial residual (resid0) = 2.516156837e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.459755602e-30, 1.772447383e-11 MLMG: Timers: Solve = 0.00626432 Iter = 0.006098108 Bottom = 0.000254514 Done calling nodal solver Timestep 18 ends with TIME = 0.05365989493 DT = 0.004371810763 Timing summary: Advection :0.005963516001 seconds MAC Proj :0.005137677 seconds Nodal Proj :0.007012426 seconds Reactions :0.011975181 seconds Misc :0.001528126 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.031787152 Call to estdt for level 0 gives dt_lev = 3.122265826e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 19 gives dt =1e+20 dt_growth factor limits the new dt = 0.004590401301 Timestep 19 starts with TIME = 0.05365989493 DT = 0.004590401301 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.361324287e-30 MLMG: Initial residual (resid0) = 6.361324287e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.987979552e-40, 9.413102181e-11 MLMG: Timers: Solve = 0.004324171 Iter = 0.004128211 Bottom = 0.000161117 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.361324287e-30 MLMG: Initial residual (resid0) = 5.987979552e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000206304 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.641964679e-19 MLMG: Initial residual (resid0) = 2.641964679e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.682802363e-30, 1.772469708e-11 MLMG: Timers: Solve = 0.006961047 Iter = 0.006786354 Bottom = 0.000259476 Done calling nodal solver Timestep 19 ends with TIME = 0.05825029623 DT = 0.004590401301 Timing summary: Advection :0.006291345 seconds MAC Proj :0.005212319 seconds Nodal Proj :0.007682887 seconds Reactions :0.011851595 seconds Misc :0.001525084001 seconds Base State :4.599996828e-08 seconds Time to advance time step: 0.03272181 Call to estdt for level 0 gives dt_lev = 2.974206455e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 20 gives dt =1e+20 dt_growth factor limits the new dt = 0.004819921366 Timestep 20 starts with TIME = 0.05825029623 DT = 0.004819921366 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.683696559e-30 MLMG: Initial residual (resid0) = 6.683696559e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.287226839e-40, 9.406810713e-11 MLMG: Timers: Solve = 0.004279703 Iter = 0.004088671 Bottom = 0.000165707 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.683696559e-30 MLMG: Initial residual (resid0) = 6.287226839e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000624857 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.774062913e-19 MLMG: Initial residual (resid0) = 2.774062913e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.916899148e-30, 1.772454087e-11 MLMG: Timers: Solve = 0.006282404 Iter = 0.006121055 Bottom = 0.000255503 Done calling nodal solver Timestep 20 ends with TIME = 0.0630702176 DT = 0.004819921366 Timing summary: Advection :0.006563326 seconds MAC Proj :0.005729504 seconds Nodal Proj :0.006988285 seconds Reactions :0.012387165 seconds Misc :0.001607115 seconds Base State :4.499997885e-08 seconds Time to advance time step: 0.033423406 Call to estdt for level 0 gives dt_lev = 2.83287101e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 21 gives dt =1e+20 dt_growth factor limits the new dt = 0.005060917435 Timestep 21 starts with TIME = 0.0630702176 DT = 0.005060917435 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.019131084e-30 MLMG: Initial residual (resid0) = 7.019131084e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.601334897e-40, 9.40477506e-11 MLMG: Timers: Solve = 0.004506139 Iter = 0.004260204 Bottom = 0.000159355 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.019131084e-30 MLMG: Initial residual (resid0) = 6.601334897e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00020346 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.869691725e-19 MLMG: Initial residual (resid0) = 2.869691725e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.297839054e-29, 8.007267937e-11 MLMG: Timers: Solve = 0.006264616 Iter = 0.006092586 Bottom = 0.00025214 Done calling nodal solver Timestep 21 ends with TIME = 0.06813113503 DT = 0.005060917435 Timing summary: Advection :0.005872074 seconds MAC Proj :0.005341739 seconds Nodal Proj :0.006971447 seconds Reactions :0.01181833 seconds Misc :0.001503349 seconds Base State :4.499997885e-08 seconds Time to advance time step: 0.031661728 Call to estdt for level 0 gives dt_lev = 5.895631152e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 22 gives dt =1e+20 dt_growth factor limits the new dt = 0.005313963306 Timestep 22 starts with TIME = 0.06813113503 DT = 0.005313963306 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 2.174577793e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 1.127461332e-30, 5.184736713e-11 MLMG: Timers: Solve = 0.004281967 Iter = 0.004089789 Bottom = 0.000169544 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 1.127461332e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000189379 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.058404362e-19 MLMG: Initial residual (resid0) = 3.058404362e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.420866866e-30, 1.772449364e-11 MLMG: Timers: Solve = 0.006161166 Iter = 0.005983945 Bottom = 0.000253844 Done calling nodal solver Timestep 22 ends with TIME = 0.07344509834 DT = 0.005313963306 Timing summary: Advection :0.005632258 seconds MAC Proj :0.005082383 seconds Nodal Proj :0.006855135 seconds Reactions :0.01149903 seconds Misc :0.001538904 seconds Base State :4.300000001e-08 seconds Time to advance time step: 0.030762592 Call to estdt for level 0 gives dt_lev = 2.554672307e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 23 gives dt =1e+20 dt_growth factor limits the new dt = 0.005579661472 Timestep 23 starts with TIME = 0.07344509834 DT = 0.005579661472 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.733416233e-30 MLMG: Initial residual (resid0) = 7.733416233e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.972214945e-40, 7.722608954e-11 MLMG: Timers: Solve = 0.004331053 Iter = 0.004147697 Bottom = 0.000166336 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.733416233e-30 MLMG: Initial residual (resid0) = 5.972214945e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000202007 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.21132458e-19 MLMG: Initial residual (resid0) = 3.21132458e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.691941506e-30, 1.77245911e-11 MLMG: Timers: Solve = 0.006266837 Iter = 0.006075798 Bottom = 0.000254416 Done calling nodal solver Timestep 23 ends with TIME = 0.07902475981 DT = 0.005579661472 Timing summary: Advection :0.005808493 seconds MAC Proj :0.005149087 seconds Nodal Proj :0.006982375 seconds Reactions :0.011701447 seconds Misc :0.001517056 seconds Base State :5.09999154e-08 seconds Time to advance time step: 0.031312171 Call to estdt for level 0 gives dt_lev = 2.439853595e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 24 gives dt =1e+20 dt_growth factor limits the new dt = 0.005858644545 Timestep 24 starts with TIME = 0.07902475981 DT = 0.005858644545 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.005903751e-30 MLMG: Initial residual (resid0) = 8.005903751e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 7.641995188e-40, 9.54544974e-11 MLMG: Timers: Solve = 0.004322606 Iter = 0.004120834 Bottom = 0.000165744 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.005903751e-30 MLMG: Initial residual (resid0) = 7.641995188e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00020207 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.371890809e-19 MLMG: Initial residual (resid0) = 3.371890809e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.976497655e-30, 1.772446972e-11 MLMG: Timers: Solve = 0.006123834 Iter = 0.005944961 Bottom = 0.000255809 Done calling nodal solver Timestep 24 ends with TIME = 0.08488340435 DT = 0.005858644545 Timing summary: Advection :0.005879120999 seconds MAC Proj :0.005156218 seconds Nodal Proj :0.006876527 seconds Reactions :0.0120377 seconds Misc :0.001520067 seconds Base State :5.09999154e-08 seconds Time to advance time step: 0.031623035 Call to estdt for level 0 gives dt_lev = 2.326594909e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 25 gives dt =1e+20 dt_growth factor limits the new dt = 0.006151576773 Timestep 25 starts with TIME = 0.08488340435 DT = 0.006151576773 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.528437685e-30 MLMG: Initial residual (resid0) = 8.528437685e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.023638825e-40, 9.408099257e-11 MLMG: Timers: Solve = 0.004304776 Iter = 0.004113043 Bottom = 0.00016786 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.528437685e-30 MLMG: Initial residual (resid0) = 8.023638825e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000200378 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.540485349e-19 MLMG: Initial residual (resid0) = 3.540485349e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.275401983e-30, 1.772469411e-11 MLMG: Timers: Solve = 0.006238808 Iter = 0.006073298 Bottom = 0.0002584 Done calling nodal solver Timestep 25 ends with TIME = 0.09103498113 DT = 0.006151576773 Timing summary: Advection :0.006074774 seconds MAC Proj :0.005132379 seconds Nodal Proj :0.006996524 seconds Reactions :0.011689074 seconds Misc :0.001438857999 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.031493215 Call to estdt for level 0 gives dt_lev = 2.217290439e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 26 gives dt =1e+20 dt_growth factor limits the new dt = 0.006459155611 Timestep 26 starts with TIME = 0.09103498113 DT = 0.006459155611 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.960898042e-30 MLMG: Initial residual (resid0) = 8.960898042e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.424494264e-40, 9.401395065e-11 MLMG: Timers: Solve = 0.004263397 Iter = 0.004075968 Bottom = 0.000167312 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.960898042e-30 MLMG: Initial residual (resid0) = 8.424494264e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000199142 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.717509617e-19 MLMG: Initial residual (resid0) = 3.717509617e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.589087822e-30, 1.772446746e-11 MLMG: Timers: Solve = 0.006303142 Iter = 0.006138385 Bottom = 0.000254862 Done calling nodal solver Timestep 26 ends with TIME = 0.09749413674 DT = 0.006459155611 Timing summary: Advection :0.005810418 seconds MAC Proj :0.005091713 seconds Nodal Proj :0.006996521 seconds Reactions :0.011769664 seconds Misc :0.001536252 seconds Base State :4.599996828e-08 seconds Time to advance time step: 0.031357405 Call to estdt for level 0 gives dt_lev = 2.112523985e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 27 gives dt =1e+20 dt_growth factor limits the new dt = 0.006782113392 Timestep 27 starts with TIME = 0.09749413674 DT = 0.006782113392 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.409848931e-30 MLMG: Initial residual (resid0) = 9.409848931e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.845794647e-40, 9.400570308e-11 MLMG: Timers: Solve = 0.004334902 Iter = 0.004126361 Bottom = 0.00016857 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.409848931e-30 MLMG: Initial residual (resid0) = 8.845794647e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000294708 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.903385097e-19 MLMG: Initial residual (resid0) = 3.903385097e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.918614436e-30, 1.772465248e-11 MLMG: Timers: Solve = 0.006216092 Iter = 0.00603487 Bottom = 0.000254505 Done calling nodal solver Timestep 27 ends with TIME = 0.1042762501 DT = 0.006782113392 Timing summary: Advection :0.005936833 seconds MAC Proj :0.005244621 seconds Nodal Proj :0.006917522 seconds Reactions :0.01177027 seconds Misc :0.001446198 seconds Base State :5.500032785e-08 seconds Time to advance time step: 0.031473307 Call to estdt for level 0 gives dt_lev = 2.01240705e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 28 gives dt =1e+20 dt_growth factor limits the new dt = 0.007121219061 Timestep 28 starts with TIME = 0.1042762501 DT = 0.007121219061 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.87985185e-30 MLMG: Initial residual (resid0) = 9.87985185e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 9.288212598e-40, 9.401165867e-11 MLMG: Timers: Solve = 0.004445338 Iter = 0.004256837 Bottom = 0.000186819 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.87985185e-30 MLMG: Initial residual (resid0) = 9.288212598e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000210518 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.098554352e-19 MLMG: Initial residual (resid0) = 4.098554352e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.264463305e-30, 1.772445277e-11 MLMG: Timers: Solve = 0.006350546 Iter = 0.006183453 Bottom = 0.000255224 Done calling nodal solver Timestep 28 ends with TIME = 0.1113974692 DT = 0.007121219061 Timing summary: Advection :0.005932968 seconds MAC Proj :0.005290858 seconds Nodal Proj :0.007055179 seconds Reactions :0.011772096 seconds Misc :0.001518303 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.031731377 Call to estdt for level 0 gives dt_lev = 1.916892684e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 29 gives dt =1e+20 dt_growth factor limits the new dt = 0.007477280014 Timestep 29 starts with TIME = 0.1113974692 DT = 0.007477280014 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.037509187e-29 MLMG: Initial residual (resid0) = 1.037509187e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 9.752953234e-40, 9.400353609e-11 MLMG: Timers: Solve = 0.004248635 Iter = 0.004056637 Bottom = 0.000162847 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.037509187e-29 MLMG: Initial residual (resid0) = 9.752953234e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000200747 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.30348207e-19 MLMG: Initial residual (resid0) = 4.30348207e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.627789989e-30, 1.772469332e-11 MLMG: Timers: Solve = 0.006226759 Iter = 0.006034891 Bottom = 0.00025406 Done calling nodal solver Timestep 29 ends with TIME = 0.1188747492 DT = 0.007477280014 Timing summary: Advection :0.005962632 seconds MAC Proj :0.005082174 seconds Nodal Proj :0.006923194 seconds Reactions :0.011831401 seconds Misc :0.001553035999 seconds Base State :5.3000349e-08 seconds Time to advance time step: 0.031493769 Call to estdt for level 0 gives dt_lev = 1.825810886e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 30 gives dt =1e+20 dt_growth factor limits the new dt = 0.007851144015 Timestep 30 starts with TIME = 0.1188747492 DT = 0.007851144015 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.089501496e-29 MLMG: Initial residual (resid0) = 1.089501496e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.024106753e-39, 9.399773718e-11 MLMG: Timers: Solve = 0.004342886 Iter = 0.004159169 Bottom = 0.000172937 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.089501496e-29 MLMG: Initial residual (resid0) = 1.024106753e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000188942 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.518656173e-19 MLMG: Initial residual (resid0) = 4.518656173e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.00907597e-30, 1.772446423e-11 MLMG: Timers: Solve = 0.00627912 Iter = 0.006086878 Bottom = 0.000258476 Done calling nodal solver Timestep 30 ends with TIME = 0.1267258932 DT = 0.007851144015 Timing summary: Advection :0.005842949 seconds MAC Proj :0.005173125 seconds Nodal Proj :0.006973265 seconds Reactions :0.011739011 seconds Misc :0.001502627 seconds Base State :6.29997885e-08 seconds Time to advance time step: 0.031387204 Call to estdt for level 0 gives dt_lev = 1.738995247e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 31 gives dt =1e+20 dt_growth factor limits the new dt = 0.008243701216 Timestep 31 starts with TIME = 0.1267258932 DT = 0.008243701216 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.144079624e-29 MLMG: Initial residual (resid0) = 1.144079624e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.075258351e-39, 9.398457314e-11 MLMG: Timers: Solve = 0.004305113 Iter = 0.00410967 Bottom = 0.000163692 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.144079624e-29 MLMG: Initial residual (resid0) = 1.075258351e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000199946 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.744588982e-19 MLMG: Initial residual (resid0) = 4.744588982e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.409669399e-30, 1.772475852e-11 MLMG: Timers: Solve = 0.00629946 Iter = 0.00612347 Bottom = 0.000252377 Done calling nodal solver Timestep 31 ends with TIME = 0.1349695944 DT = 0.008243701216 Timing summary: Advection :0.006088703 seconds MAC Proj :0.005148112 seconds Nodal Proj :0.007027043 seconds Reactions :0.011921774 seconds Misc :0.00151261 seconds Base State :4.69999577e-08 seconds Time to advance time step: 0.031855209 Call to estdt for level 0 gives dt_lev = 1.656260551e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 32 gives dt =1e+20 dt_growth factor limits the new dt = 0.008655886277 Timestep 32 starts with TIME = 0.1349695944 DT = 0.008655886277 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.201372446e-29 MLMG: Initial residual (resid0) = 1.201372446e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.129010758e-39, 9.397674818e-11 MLMG: Timers: Solve = 0.004269148 Iter = 0.004062267 Bottom = 0.000161279 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.201372446e-29 MLMG: Initial residual (resid0) = 1.129010758e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000206019 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.981818431e-19 MLMG: Initial residual (resid0) = 4.981818431e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.830148054e-30, 1.772474886e-11 MLMG: Timers: Solve = 0.006220719 Iter = 0.006049198 Bottom = 0.000252832 Done calling nodal solver Timestep 32 ends with TIME = 0.1436254807 DT = 0.008655886277 Timing summary: Advection :0.005884628001 seconds MAC Proj :0.005104853 seconds Nodal Proj :0.00691626 seconds Reactions :0.012032339 seconds Misc :0.001487936999 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.031589713 Call to estdt for level 0 gives dt_lev = 1.577440861e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 33 gives dt =1e+20 dt_growth factor limits the new dt = 0.00908868059 Timestep 33 starts with TIME = 0.1436254807 DT = 0.00908868059 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.261567528e-29 MLMG: Initial residual (resid0) = 1.261567528e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.185462067e-39, 9.396738906e-11 MLMG: Timers: Solve = 0.004353671 Iter = 0.004152773 Bottom = 0.000170092 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.261567528e-29 MLMG: Initial residual (resid0) = 1.185462067e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000192463 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.230909353e-19 MLMG: Initial residual (resid0) = 5.230909353e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.271474901e-30, 1.772440368e-11 MLMG: Timers: Solve = 0.006312883 Iter = 0.006149401 Bottom = 0.000250647 Done calling nodal solver Timestep 33 ends with TIME = 0.1527141613 DT = 0.00908868059 Timing summary: Advection :0.005855676 seconds MAC Proj :0.005166984 seconds Nodal Proj :0.007020998 seconds Reactions :0.011665256 seconds Misc :0.001510497999 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.031386113 Call to estdt for level 0 gives dt_lev = 1.502378414e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 34 gives dt =1e+20 dt_growth factor limits the new dt = 0.00954311462 Timestep 34 starts with TIME = 0.1527141613 DT = 0.00954311462 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.324582667e-29 MLMG: Initial residual (resid0) = 1.324582667e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.244696354e-39, 9.396894474e-11 MLMG: Timers: Solve = 0.004352907 Iter = 0.004163953 Bottom = 0.000165908 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.324582667e-29 MLMG: Initial residual (resid0) = 1.244696354e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00019731 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.49245482e-19 MLMG: Initial residual (resid0) = 5.49245482e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.735238831e-30, 1.772474995e-11 MLMG: Timers: Solve = 0.0063368 Iter = 0.006159738 Bottom = 0.000252904 Done calling nodal solver Timestep 34 ends with TIME = 0.1622572759 DT = 0.00954311462 Timing summary: Advection :0.006022881001 seconds MAC Proj :0.005194559 seconds Nodal Proj :0.007055424 seconds Reactions :0.012021155 seconds Misc :0.00154559 seconds Base State :4.599996828e-08 seconds Time to advance time step: 0.031984007 Call to estdt for level 0 gives dt_lev = 1.430880358e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 35 gives dt =1e+20 dt_growth factor limits the new dt = 0.01002027035 Timestep 35 starts with TIME = 0.1622572759 DT = 0.01002027035 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.390963587e-29 MLMG: Initial residual (resid0) = 1.390963587e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.306904197e-39, 9.395675121e-11 MLMG: Timers: Solve = 0.004315941 Iter = 0.004127452 Bottom = 0.000170447 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.390963587e-29 MLMG: Initial residual (resid0) = 1.306904197e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000192158 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.681793327e-19 MLMG: Initial residual (resid0) = 5.681793327e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.54956653e-29, 8.00727212e-11 MLMG: Timers: Solve = 0.006221277 Iter = 0.006055636 Bottom = 0.000253964 Done calling nodal solver Timestep 35 ends with TIME = 0.1722775463 DT = 0.01002027035 Timing summary: Advection :0.005865183 seconds MAC Proj :0.005134213 seconds Nodal Proj :0.00692718 seconds Reactions :0.011936252 seconds Misc :0.001518152 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.031531236 Call to estdt for level 0 gives dt_lev = 2.977695677e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 36 gives dt =1e+20 dt_growth factor limits the new dt = 0.01052128387 Timestep 36 starts with TIME = 0.1722775463 DT = 0.01052128387 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 4.305515288e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.23205761e-30, 5.184182289e-11 MLMG: Timers: Solve = 0.004268227 Iter = 0.0040737 Bottom = 0.000161009 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 2.23205761e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000207728 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.055431439e-19 MLMG: Initial residual (resid0) = 6.055431439e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.073301499e-29, 1.772460822e-11 MLMG: Timers: Solve = 0.006391009 Iter = 0.00620977 Bottom = 0.000252793 Done calling nodal solver Timestep 36 ends with TIME = 0.1827988301 DT = 0.01052128387 Timing summary: Advection :0.005495536 seconds MAC Proj :0.005107463001 seconds Nodal Proj :0.007108012 seconds Reactions :0.011951729 seconds Misc :0.001506557 seconds Base State :5.999982022e-08 seconds Time to advance time step: 0.031330732 Call to estdt for level 0 gives dt_lev = 1.290254218e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 37 gives dt =1e+20 dt_growth factor limits the new dt = 0.01104734806 Timestep 37 starts with TIME = 0.1827988301 DT = 0.01104734806 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.53169484e-29 MLMG: Initial residual (resid0) = 1.53169484e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.182368e-39, 7.719344411e-11 MLMG: Timers: Solve = 0.00425744 Iter = 0.004072494 Bottom = 0.000160875 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.53169484e-29 MLMG: Initial residual (resid0) = 1.182368e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000192676 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.264177143e-19 MLMG: Initial residual (resid0) = 6.264177143e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.855307908e-29, 7.75091093e-11 MLMG: Timers: Solve = 0.006185439 Iter = 0.006020217 Bottom = 0.000249373 Done calling nodal solver Timestep 37 ends with TIME = 0.1938461782 DT = 0.01104734806 Timing summary: Advection :0.005855094 seconds MAC Proj :0.005074186 seconds Nodal Proj :0.006892349 seconds Reactions :0.01187598 seconds Misc :0.001516329 seconds Base State :4.399998943e-08 seconds Time to advance time step: 0.03136235 Call to estdt for level 0 gives dt_lev = 2.789559822e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 38 gives dt =1e+20 dt_growth factor limits the new dt = 0.01159971547 Timestep 38 starts with TIME = 0.1938461782 DT = 0.01159971547 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 4.746830605e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.490741235e-30, 5.247166883e-11 MLMG: Timers: Solve = 0.004283169 Iter = 0.004074223 Bottom = 0.000162923 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 2.490741235e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000199637 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.676113162e-19 MLMG: Initial residual (resid0) = 6.676113162e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.183315432e-29, 1.772461615e-11 MLMG: Timers: Solve = 0.00633877 Iter = 0.00615948 Bottom = 0.000254744 Done calling nodal solver Timestep 38 ends with TIME = 0.2054458937 DT = 0.01159971547 Timing summary: Advection :0.005868885 seconds MAC Proj :0.005105846 seconds Nodal Proj :0.007060437 seconds Reactions :0.011849765 seconds Misc :0.001531756 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.031583705 Call to estdt for level 0 gives dt_lev = 1.168429834e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 39 gives dt =1e+20 dt_growth factor limits the new dt = 0.01217970124 Timestep 39 starts with TIME = 0.2054458937 DT = 0.01217970124 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.536277128e-29 MLMG: Initial residual (resid0) = 1.536277128e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.179416865e-39, 7.677110101e-11 MLMG: Timers: Solve = 0.004356972 Iter = 0.004089306 Bottom = 0.000158551 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.536277128e-29 MLMG: Initial residual (resid0) = 1.179416865e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000282447 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.00991882e-19 MLMG: Initial residual (resid0) = 7.00991882e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.242475185e-29, 1.77245303e-11 MLMG: Timers: Solve = 0.006175491 Iter = 0.006010001 Bottom = 0.00025287 Done calling nodal solver Timestep 39 ends with TIME = 0.2176255949 DT = 0.01217970124 Timing summary: Advection :0.006423265 seconds MAC Proj :0.005252746 seconds Nodal Proj :0.00686972 seconds Reactions :0.011723153 seconds Misc :0.001508813 seconds Base State :4.499997885e-08 seconds Time to advance time step: 0.031942686 Call to estdt for level 0 gives dt_lev = 1.116506554e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 40 gives dt =1e+20 dt_growth factor limits the new dt = 0.0127886863 Timestep 40 starts with TIME = 0.2176255949 DT = 0.0127886863 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.750089547e-29 MLMG: Initial residual (resid0) = 1.750089547e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.668229006e-39, 9.532249417e-11 MLMG: Timers: Solve = 0.004260811 Iter = 0.004070583 Bottom = 0.000164684 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.750089547e-29 MLMG: Initial residual (resid0) = 1.668229006e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000238784 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.360414761e-19 MLMG: Initial residual (resid0) = 7.360414761e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.304586426e-29, 1.772436022e-11 MLMG: Timers: Solve = 0.006304584 Iter = 0.006131243 Bottom = 0.000255261 Done calling nodal solver Timestep 40 ends with TIME = 0.2304142812 DT = 0.0127886863 Timing summary: Advection :0.005992862 seconds MAC Proj :0.00514118 seconds Nodal Proj :0.007015769 seconds Reactions :0.011861352 seconds Misc :0.001516741 seconds Base State :5.399988368e-08 seconds Time to advance time step: 0.03167633 Call to estdt for level 0 gives dt_lev = 1.065037272e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 41 gives dt =1e+20 dt_growth factor limits the new dt = 0.01342812062 Timestep 41 starts with TIME = 0.2304142812 DT = 0.01342812062 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.862969069e-29 MLMG: Initial residual (resid0) = 1.862969069e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.751653909e-39, 9.402485193e-11 MLMG: Timers: Solve = 0.004320241 Iter = 0.004074943 Bottom = 0.000166212 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.862969069e-29 MLMG: Initial residual (resid0) = 1.751653909e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000204843 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.728435499e-19 MLMG: Initial residual (resid0) = 7.728435499e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.369817673e-29, 1.772438514e-11 MLMG: Timers: Solve = 0.00623607 Iter = 0.006070214 Bottom = 0.000258799 Done calling nodal solver Timestep 41 ends with TIME = 0.2438424018 DT = 0.01342812062 Timing summary: Advection :0.005806942 seconds MAC Proj :0.005146959 seconds Nodal Proj :0.00692484 seconds Reactions :0.011627959 seconds Misc :0.001523102999 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.031178447 Call to estdt for level 0 gives dt_lev = 1.015215791e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 42 gives dt =1e+20 dt_growth factor limits the new dt = 0.01409952665 Timestep 42 starts with TIME = 0.2438424018 DT = 0.01409952665 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.957338259e-29 MLMG: Initial residual (resid0) = 1.957338259e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.839075315e-39, 9.395797107e-11 MLMG: Timers: Solve = 0.004277041 Iter = 0.004088431 Bottom = 0.00016944 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.957338259e-29 MLMG: Initial residual (resid0) = 1.839075315e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000193735 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.114857274e-19 MLMG: Initial residual (resid0) = 8.114857274e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.43835189e-29, 1.772491914e-11 MLMG: Timers: Solve = 0.006292198 Iter = 0.006122096 Bottom = 0.000254151 Done calling nodal solver Timestep 42 ends with TIME = 0.2579419285 DT = 0.01409952665 Timing summary: Advection :0.005989173 seconds MAC Proj :0.005109319 seconds Nodal Proj :0.006990058 seconds Reactions :0.011771173 seconds Misc :0.001511027 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.031514899 Call to estdt for level 0 gives dt_lev = 9.67369433e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 43 gives dt =1e+20 dt_growth factor limits the new dt = 0.01480450298 Timestep 43 starts with TIME = 0.2579419285 DT = 0.01480450298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.055380727e-29 MLMG: Initial residual (resid0) = 2.055380727e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.931014507e-39, 9.394923682e-11 MLMG: Timers: Solve = 0.004325659 Iter = 0.004137231 Bottom = 0.000170115 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.055380727e-29 MLMG: Initial residual (resid0) = 1.931014507e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000201871 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.520600138e-19 MLMG: Initial residual (resid0) = 8.520600138e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.510227596e-29, 1.772442752e-11 MLMG: Timers: Solve = 0.006244141 Iter = 0.006059461 Bottom = 0.000256329 Done calling nodal solver Timestep 43 ends with TIME = 0.2727464314 DT = 0.01480450298 Timing summary: Advection :0.00595046 seconds MAC Proj :0.005150901 seconds Nodal Proj :0.006947178 seconds Reactions :0.011972879 seconds Misc :0.001514378 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.031697667 Call to estdt for level 0 gives dt_lev = 9.21627116e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 44 gives dt =1e+20 dt_growth factor limits the new dt = 0.01554472813 Timestep 44 starts with TIME = 0.2727464314 DT = 0.01554472813 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.158317685e-29 MLMG: Initial residual (resid0) = 2.158317685e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.027620023e-39, 9.394446598e-11 MLMG: Timers: Solve = 0.004266522 Iter = 0.004076372 Bottom = 0.000160633 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.158317685e-29 MLMG: Initial residual (resid0) = 2.027620023e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000192802 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.946630145e-19 MLMG: Initial residual (resid0) = 8.946630145e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.585752938e-29, 1.772458359e-11 MLMG: Timers: Solve = 0.006165127 Iter = 0.006000202 Bottom = 0.000254127 Done calling nodal solver Timestep 44 ends with TIME = 0.2882911596 DT = 0.01554472813 Timing summary: Advection :0.005818852 seconds MAC Proj :0.005079791 seconds Nodal Proj :0.006888301 seconds Reactions :0.011846415 seconds Misc :0.001530103 seconds Base State :5.799984137e-08 seconds Time to advance time step: 0.031327905 Call to estdt for level 0 gives dt_lev = 8.779341895e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 45 gives dt =1e+20 dt_growth factor limits the new dt = 0.01632196453 Timestep 45 starts with TIME = 0.2882911596 DT = 0.01632196453 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.266393495e-29 MLMG: Initial residual (resid0) = 2.266393495e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.128720905e-39, 9.392547718e-11 MLMG: Timers: Solve = 0.004344148 Iter = 0.004150212 Bottom = 0.000158759 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.266393495e-29 MLMG: Initial residual (resid0) = 2.128720905e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000197506 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.053842861e-18 MLMG: Initial residual (resid0) = 1.053842861e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 6.6812532e-29, 6.339895109e-11 MLMG: Timers: Solve = 0.006219819 Iter = 0.006043887 Bottom = 0.000252072 Done calling nodal solver Timestep 45 ends with TIME = 0.3046131241 DT = 0.01632196453 Timing summary: Advection :0.005856027001 seconds MAC Proj :0.005172986 seconds Nodal Proj :0.006930898001 seconds Reactions :0.011794101 seconds Misc :0.001525519 seconds Base State :4.600042303e-08 seconds Time to advance time step: 0.031424956 Call to estdt for level 0 gives dt_lev = 2.02744569e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 46 gives dt =1e+20 dt_growth factor limits the new dt = 0.01713806276 Timestep 46 starts with TIME = 0.3046131241 DT = 0.01713806276 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 7.013230718e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.386529476e-30, 4.828772376e-11 MLMG: Timers: Solve = 0.004267729 Iter = 0.004079463 Bottom = 0.000161807 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 3.386529476e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000210838 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 9.863659735e-19 MLMG: Initial residual (resid0) = 9.863659735e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.748311055e-29, 1.772477054e-11 MLMG: Timers: Solve = 0.00625117 Iter = 0.006084446 Bottom = 0.000258604 Done calling nodal solver Timestep 46 ends with TIME = 0.3217511869 DT = 0.01713806276 Timing summary: Advection :0.005620873 seconds MAC Proj :0.005117457 seconds Nodal Proj :0.006969317999 seconds Reactions :0.011712842 seconds Misc :0.001517155 seconds Base State :5.09999154e-08 seconds Time to advance time step: 0.031089532 Call to estdt for level 0 gives dt_lev = 7.924349732e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 47 gives dt =1e+20 dt_growth factor limits the new dt = 0.0179949659 Timestep 47 starts with TIME = 0.3217511869 DT = 0.0179949659 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.807852852e-29 MLMG: Initial residual (resid0) = 1.807852852e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.37289975e-39, 7.594090129e-11 MLMG: Timers: Solve = 0.004348138 Iter = 0.004157589 Bottom = 0.000160117 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.807852852e-29 MLMG: Initial residual (resid0) = 1.37289975e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000191589 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.035684272e-18 MLMG: Initial residual (resid0) = 1.035684272e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.835690497e-29, 1.772442188e-11 MLMG: Timers: Solve = 0.006307584 Iter = 0.006137124 Bottom = 0.000254628 Done calling nodal solver Timestep 47 ends with TIME = 0.3397461528 DT = 0.0179949659 Timing summary: Advection :0.005719177 seconds MAC Proj :0.005164349 seconds Nodal Proj :0.007020947 seconds Reactions :0.011893082 seconds Misc :0.001502258001 seconds Base State :9.399991541e-08 seconds Time to advance time step: 0.03144921 Call to estdt for level 0 gives dt_lev = 7.566055076e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 48 gives dt =1e+20 dt_growth factor limits the new dt = 0.01889471419 Timestep 48 starts with TIME = 0.3397461528 DT = 0.01889471419 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.590190152e-29 MLMG: Initial residual (resid0) = 2.590190152e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.464371124e-39, 9.514247908e-11 MLMG: Timers: Solve = 0.004282858 Iter = 0.004091736 Bottom = 0.000161601 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.590190152e-29 MLMG: Initial residual (resid0) = 2.464371124e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000195259 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.087468486e-18 MLMG: Initial residual (resid0) = 1.087468486e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.927461059e-29, 1.772429348e-11 MLMG: Timers: Solve = 0.006145574 Iter = 0.005977082 Bottom = 0.00025042 Done calling nodal solver Timestep 48 ends with TIME = 0.358640867 DT = 0.01889471419 Timing summary: Advection :0.005909054 seconds MAC Proj :0.005084009 seconds Nodal Proj :0.006835291 seconds Reactions :0.011807008 seconds Misc :0.001576982 seconds Base State :5.299989425e-08 seconds Time to advance time step: 0.031362326 Call to estdt for level 0 gives dt_lev = 7.214019049e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 49 gives dt =1e+20 dt_growth factor limits the new dt = 0.0198394499 Timestep 49 starts with TIME = 0.358640867 DT = 0.0198394499 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.753963702e-29 MLMG: Initial residual (resid0) = 2.753963702e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.587705007e-39, 9.396293077e-11 MLMG: Timers: Solve = 0.00428841 Iter = 0.004102002 Bottom = 0.00016947 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.753963702e-29 MLMG: Initial residual (resid0) = 2.587682586e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000246386 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.086359695e-18 MLMG: Initial residual (resid0) = 1.086359695e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 4.015978009e-29, 3.69672957e-11 MLMG: Timers: Solve = 0.006215132 Iter = 0.006036505 Bottom = 0.00025364 Done calling nodal solver Timestep 49 ends with TIME = 0.3784803169 DT = 0.0198394499 Timing summary: Advection :0.005909446999 seconds MAC Proj :0.005165479 seconds Nodal Proj :0.006935094 seconds Reactions :0.011726732 seconds Misc :0.001519969001 seconds Base State :5.299989425e-08 seconds Time to advance time step: 0.031397139 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 50 gives dt =1e+20 dt_growth factor limits the new dt = 0.0208314224 Timestep 50 starts with TIME = 0.3784803169 DT = 0.0208314224 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 8.242756114e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.779842146e-30, 4.585653262e-11 MLMG: Timers: Solve = 0.004279326 Iter = 0.004089328 Bottom = 0.000159869 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 3.779842146e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000191667 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.198934006e-18 MLMG: Initial residual (resid0) = 1.198934006e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 2.12508073e-29, 1.772475149e-11 MLMG: Timers: Solve = 0.006260457 Iter = 0.006097183 Bottom = 0.000252659 Done calling nodal solver Timestep 50 ends with TIME = 0.3993117393 DT = 0.0208314224 Timing summary: Advection :0.005605371 seconds MAC Proj :0.005093505 seconds Nodal Proj :0.006956079999 seconds Reactions :0.011879302 seconds Misc :0.001512783 seconds Base State :4.69999577e-08 seconds Time to advance time step: 0.03129689 Writing plotfile 50 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.018682848 Writing checkpoint 50 Writing checkpoint chk0000050 Total Time: 3.292346676 Unused ParmParse Variables: [TOP]::maestro.v(nvals = 1) :: [1] [TOP]::amr.check_file(nvals = 1) :: [test_stability_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] AMReX (23.03-1-gb96f6e5bd13d) finalized