MPI initialized with 16 MPI processes MPI initialized with thread support level 0 AMReX (23.07-7-g88f03408f18a) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = 5peaks_const_grav.dat model file = 5peaks_const_grav.dat reading initial model 1000 points found in the initial model 10 variables found in the initial model WARNING: variable not found: gravity WARNING: variable not found: abar WARNING: variable not found: zbar WARNING: variable not found: gpot WARNING: variable not found: cno model file mapping, level: 0 dr of MAESTRO base state = 93750000.000000 dr of input file data = 10010010.010010 maximum radius (cell-centered) of input model = 10000000000.000000 WARNING: resolution of base state array is not an integer multiple of the initial model's resolution. make sure this is a desired property as this could lead to aliasing when performing the interpolation. modulus = 3659909.909910 setting r_cutoff to 105 radius at r_cutoff 9890625000 Maximum HSE Error = 0.054171 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile test_stability_pltInitData after InitData inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.022524337 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.00032745 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile test_stability_pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.021696376 Call to firstdt for level 0 gives dt_lev = 0.01907406555 Multiplying dt_lev by init_shrink; dt_lev = 0.001907406555 Minimum firstdt over all levels = 0.001907406555 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 4.945354899e-27 MLMG: Initial residual (resid0) = 4.945354899e-27 MLMG: Final Iter. 3 resid, resid/bnorm = 2.357566962e-30, 0.0004767235133 MLMG: Timers: Solve = 0.002979241 Iter = 0.002738861 Bottom = 0.000101406 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 1 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #2 Calling nodal solver MLMG: Initial rhs = 2.306075226e-30 MLMG: Initial residual (resid0) = 2.306075226e-30 MLMG: Final Iter. 5 resid, resid/bnorm = 1.933632021e-37, 8.384947719e-08 MLMG: Timers: Solve = 0.003954223 Iter = 0.003740373 Bottom = 0.0001446 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 2 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #3 Calling nodal solver MLMG: Initial rhs = 9.742172191e-32 MLMG: Initial residual (resid0) = 9.742172191e-32 MLMG: Final Iter. 4 resid, resid/bnorm = 7.521071013e-41, 7.720117101e-10 MLMG: Timers: Solve = 0.003092084 Iter = 0.002886925 Bottom = 0.000121132 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 3 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Writing plotfile test_stability_pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.014941726 Doing initial pressure iteration #1 Timestep 0 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.893547601e-20 MLMG: Initial residual (resid0) = 4.893547601e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 4.517319815e-31, 9.231175792e-12 MLMG: Timers: Solve = 0.004790824 Iter = 0.004540203 Bottom = 0.00017294 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.893547507e-20 MLMG: Initial residual (resid0) = 2.477484298e-27 MLMG: Final Iter. 4 resid, resid/bnorm = 4.813594311e-30, 9.836615062e-11 MLMG: Timers: Solve = 0.001810195 Iter = 0.001588073 Bottom = 7.0549e-05 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.755411273e-17 MLMG: Initial residual (resid0) = 5.755411273e-17 MLMG: Final Iter. 9 resid, resid/bnorm = 1.02012041e-27, 1.772454411e-11 MLMG: Timers: Solve = 0.00641263 Iter = 0.006201077 Bottom = 0.000258544 Done calling nodal solver Timestep 0 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.006424908 seconds MAC Proj :0.007373253 seconds Nodal Proj :0.007294071 seconds Reactions :0.013710694 seconds Misc :0.001630278 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.040098046 Writing plotfile 0 after all initialization inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.015128079 Writing checkpoint 0 after all initialization Writing checkpoint chk0000000 Calling Evolve() Timestep 1 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.257776127e-26 MLMG: Initial residual (resid0) = 1.257776127e-26 MLMG: Final Iter. 10 resid, resid/bnorm = 1.092411925e-37, 8.685265223e-12 MLMG: Timers: Solve = 0.004414 Iter = 0.003994581 Bottom = 0.000165829 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.257776127e-26 MLMG: Initial residual (resid0) = 1.092411925e-37 MLMG: No iterations needed MLMG: Timers: Solve = 0.000235683 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.097790919e-19 MLMG: Initial residual (resid0) = 1.097790919e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.945791097e-30, 1.772460551e-11 MLMG: Timers: Solve = 0.006459078 Iter = 0.006237015 Bottom = 0.000254161 Done calling nodal solver Timestep 1 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.006480143 seconds MAC Proj :0.005400279 seconds Nodal Proj :0.007429604 seconds Reactions :0.013589837 seconds Misc :0.001826810001 seconds Base State :5.799984137e-08 seconds Time to advance time step: 0.041162399 Call to estdt for level 0 gives dt_lev = 7.191081337e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 2 gives dt =1e+20 dt_growth factor limits the new dt = 0.002002776883 Timestep 2 starts with TIME = 0.001907406555 DT = 0.002002776883 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.080398705e-27 MLMG: Initial residual (resid0) = 8.080398705e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 1.160441939e-37, 1.436119654e-11 MLMG: Timers: Solve = 0.004096591 Iter = 0.003860884 Bottom = 0.000172847 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.498306209e-27 MLMG: Initial residual (resid0) = 2.601349809e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 8.688832515e-37, 9.14777048e-11 MLMG: Timers: Solve = 0.004083178 Iter = 0.00384979 Bottom = 0.000163878 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.096671578e-19 MLMG: Initial residual (resid0) = 1.096671578e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.008844235e-29, 9.19914635e-11 MLMG: Timers: Solve = 0.006879068 Iter = 0.006537099 Bottom = 0.0002561 Done calling nodal solver Timestep 2 ends with TIME = 0.003910183437 DT = 0.002002776883 Timing summary: Advection :0.006771442001 seconds MAC Proj :0.008836886 seconds Nodal Proj :0.00773815 seconds Reactions :0.013592525 seconds Misc :0.00166771 seconds Base State :8.000006346e-08 seconds Time to advance time step: 0.038781968 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 3 gives dt =1e+20 dt_growth factor limits the new dt = 0.002102915727 Timestep 3 starts with TIME = 0.003910183437 DT = 0.002102915727 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 8.320997544e-21 MLMG: Final Iter. 10 resid, resid/bnorm = 7.676109766e-31, 9.22498742e-11 MLMG: Timers: Solve = 0.004059213 Iter = 0.00384722 Bottom = 0.000162292 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 7.676109766e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000231371 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.21031446e-19 MLMG: Initial residual (resid0) = 1.21031446e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.145209106e-30, 1.772439458e-11 MLMG: Timers: Solve = 0.00630349 Iter = 0.006096241 Bottom = 0.000260509 Done calling nodal solver Timestep 3 ends with TIME = 0.006013099164 DT = 0.002102915727 Timing summary: Advection :0.00596979 seconds MAC Proj :0.004974359 seconds Nodal Proj :0.007091668 seconds Reactions :0.013537031 seconds Misc :0.001683782 seconds Base State :5.49998731e-08 seconds Time to advance time step: 0.033453402 Call to estdt for level 0 gives dt_lev = 6.528630569e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 4 gives dt =1e+20 dt_growth factor limits the new dt = 0.002208061513 Timestep 4 starts with TIME = 0.006013099164 DT = 0.002208061513 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.308039747e-29 MLMG: Initial residual (resid0) = 1.308039747e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.129752045e-39, 8.636985596e-11 MLMG: Timers: Solve = 0.004027981 Iter = 0.003799663 Bottom = 0.000164219 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.308039747e-29 MLMG: Initial residual (resid0) = 1.129752045e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000228867 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.270830183e-19 MLMG: Initial residual (resid0) = 1.270830183e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.252495441e-30, 1.772459822e-11 MLMG: Timers: Solve = 0.006352479 Iter = 0.006144992 Bottom = 0.0002606 Done calling nodal solver Timestep 4 ends with TIME = 0.008221160677 DT = 0.002208061513 Timing summary: Advection :0.006193981 seconds MAC Proj :0.004924089 seconds Nodal Proj :0.007162633 seconds Reactions :0.013544976 seconds Misc :0.001691602 seconds Base State :8.699998943e-08 seconds Time to advance time step: 0.033683744 Call to estdt for level 0 gives dt_lev = 6.226258359e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 5 gives dt =1e+20 dt_growth factor limits the new dt = 0.002318464589 Timestep 5 starts with TIME = 0.008221160677 DT = 0.002318464589 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.295923274e-30 MLMG: Initial residual (resid0) = 3.295923274e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.024366424e-40, 9.176082608e-11 MLMG: Timers: Solve = 0.004040223 Iter = 0.003819047 Bottom = 0.000166682 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.295923274e-30 MLMG: Initial residual (resid0) = 3.024366424e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022011 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.334371692e-19 MLMG: Initial residual (resid0) = 1.334371692e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.365138268e-30, 1.772473353e-11 MLMG: Timers: Solve = 0.006337414 Iter = 0.00613041 Bottom = 0.00026196 Done calling nodal solver Timestep 5 ends with TIME = 0.01053962527 DT = 0.002318464589 Timing summary: Advection :0.006246929999 seconds MAC Proj :0.00492057 seconds Nodal Proj :0.007149146 seconds Reactions :0.013551178 seconds Misc :0.00165764 seconds Base State :8.999995771e-08 seconds Time to advance time step: 0.033698173 Call to estdt for level 0 gives dt_lev = 5.915049504e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 6 gives dt =1e+20 dt_growth factor limits the new dt = 0.002434387818 Timestep 6 starts with TIME = 0.01053962527 DT = 0.002434387818 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.377753945e-30 MLMG: Initial residual (resid0) = 3.377753945e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.175503469e-40, 9.401227921e-11 MLMG: Timers: Solve = 0.004055865 Iter = 0.003816101 Bottom = 0.00016203 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.377753945e-30 MLMG: Initial residual (resid0) = 3.175499966e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000234094 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.401090277e-19 MLMG: Initial residual (resid0) = 1.401090277e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.483342219e-30, 1.772435552e-11 MLMG: Timers: Solve = 0.006462126 Iter = 0.006231218 Bottom = 0.000255024 Done calling nodal solver Timestep 6 ends with TIME = 0.01297401308 DT = 0.002434387818 Timing summary: Advection :0.006341814001 seconds MAC Proj :0.004955349 seconds Nodal Proj :0.007405456 seconds Reactions :0.013546177 seconds Misc :0.001651089 seconds Base State :7.700009519e-08 seconds Time to advance time step: 0.034074674 Call to estdt for level 0 gives dt_lev = 5.625515433e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 7 gives dt =1e+20 dt_growth factor limits the new dt = 0.002556107209 Timestep 7 starts with TIME = 0.01297401308 DT = 0.002556107209 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.543159178e-30 MLMG: Initial residual (resid0) = 3.543159178e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.334123449e-40, 9.410030095e-11 MLMG: Timers: Solve = 0.007160596 Iter = 0.006784333 Bottom = 0.000168018 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.543159178e-30 MLMG: Initial residual (resid0) = 3.334123449e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000397997 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.471144791e-19 MLMG: Initial residual (resid0) = 1.471144791e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.607516552e-30, 1.772440461e-11 MLMG: Timers: Solve = 0.008523163 Iter = 0.008235615 Bottom = 0.000253186 Done calling nodal solver Timestep 7 ends with TIME = 0.01553012029 DT = 0.002556107209 Timing summary: Advection :0.009681665 seconds MAC Proj :0.008387676 seconds Nodal Proj :0.009634652999 seconds Reactions :0.022381693 seconds Misc :0.002286139 seconds Base State :6.600021152e-08 seconds Time to advance time step: 0.052564464 Call to estdt for level 0 gives dt_lev = 5.353255202e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 8 gives dt =1e+20 dt_growth factor limits the new dt = 0.002683912569 Timestep 8 starts with TIME = 0.01553012029 DT = 0.002683912569 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.720271341e-30 MLMG: Initial residual (resid0) = 3.720271341e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.500226363e-40, 9.408524384e-11 MLMG: Timers: Solve = 0.007673173 Iter = 0.007289934 Bottom = 0.000168177 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.720271341e-30 MLMG: Initial residual (resid0) = 3.500226363e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000239305 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.54470203e-19 MLMG: Initial residual (resid0) = 1.54470203e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.737914046e-30, 1.772454488e-11 MLMG: Timers: Solve = 0.00686713 Iter = 0.006679444 Bottom = 0.000261211 Done calling nodal solver Timestep 8 ends with TIME = 0.01821403286 DT = 0.002683912569 Timing summary: Advection :0.006864200001 seconds MAC Proj :0.008621862 seconds Nodal Proj :0.007665124 seconds Reactions :0.016753523 seconds Misc :0.001635836 seconds Base State :5.89998308e-08 seconds Time to advance time step: 0.041721165 Call to estdt for level 0 gives dt_lev = 5.095618567e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 9 gives dt =1e+20 dt_growth factor limits the new dt = 0.002818108198 Timestep 9 starts with TIME = 0.01821403286 DT = 0.002818108198 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.90613533e-30 MLMG: Initial residual (resid0) = 3.90613533e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.675781034e-40, 9.410275692e-11 MLMG: Timers: Solve = 0.004789049 Iter = 0.004574781 Bottom = 0.000163006 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.90613533e-30 MLMG: Initial residual (resid0) = 3.675781034e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000216665 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.621937132e-19 MLMG: Initial residual (resid0) = 1.621937132e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.874835628e-30, 1.772470444e-11 MLMG: Timers: Solve = 0.006379805 Iter = 0.006199886 Bottom = 0.000288851 Done calling nodal solver Timestep 9 ends with TIME = 0.02103214106 DT = 0.002818108198 Timing summary: Advection :0.006309973 seconds MAC Proj :0.005659275 seconds Nodal Proj :0.007178859 seconds Reactions :0.012547474 seconds Misc :0.001562578001 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.033405673 Call to estdt for level 0 gives dt_lev = 4.851290067e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 10 gives dt =1e+20 dt_growth factor limits the new dt = 0.002959013608 Timestep 10 starts with TIME = 0.02103214106 DT = 0.002959013608 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.101240383e-30 MLMG: Initial residual (resid0) = 4.101240383e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.859393172e-40, 9.410307155e-11 MLMG: Timers: Solve = 0.004275169 Iter = 0.004065022 Bottom = 0.00017354 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.101240383e-30 MLMG: Initial residual (resid0) = 3.859393172e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000222937 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.703033988e-19 MLMG: Initial residual (resid0) = 1.703033988e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.174814859e-29, 6.898364135e-11 MLMG: Timers: Solve = 0.006567449 Iter = 0.00634677 Bottom = 0.000263864 Done calling nodal solver Timestep 10 ends with TIME = 0.02399115467 DT = 0.002959013608 Timing summary: Advection :0.006198182 seconds MAC Proj :0.005121168 seconds Nodal Proj :0.007343339 seconds Reactions :0.012335161 seconds Misc :0.001566895 seconds Base State :5.299989425e-08 seconds Time to advance time step: 0.032725838 Call to estdt for level 0 gives dt_lev = 1.153498162e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 11 gives dt =1e+20 dt_growth factor limits the new dt = 0.003106964288 Timestep 11 starts with TIME = 0.02399115467 DT = 0.003106964288 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 1.271430598e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.310137768e-31, 4.963021794e-11 MLMG: Timers: Solve = 0.004385103 Iter = 0.004181127 Bottom = 0.000165746 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 6.310137768e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000218711 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.788185688e-19 MLMG: Initial residual (resid0) = 1.788185688e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.169478835e-30, 1.772455096e-11 MLMG: Timers: Solve = 0.006293068 Iter = 0.006114871 Bottom = 0.000254881 Done calling nodal solver Timestep 11 ends with TIME = 0.02709811896 DT = 0.003106964288 Timing summary: Advection :0.005958976 seconds MAC Proj :0.005254912 seconds Nodal Proj :0.007085192 seconds Reactions :0.012204333 seconds Misc :0.001568347 seconds Base State :5.800029612e-08 seconds Time to advance time step: 0.032228413 Call to estdt for level 0 gives dt_lev = 4.376664086e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 12 gives dt =1e+20 dt_growth factor limits the new dt = 0.003262312503 Timestep 12 starts with TIME = 0.02709811896 DT = 0.003262312503 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.931483508e-30 MLMG: Initial residual (resid0) = 2.931483508e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.211723667e-40, 7.544724916e-11 MLMG: Timers: Solve = 0.004319509 Iter = 0.004112323 Bottom = 0.000163941 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.931483508e-30 MLMG: Initial residual (resid0) = 2.211723667e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000273756 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.877594972e-19 MLMG: Initial residual (resid0) = 1.877594972e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.328006944e-30, 1.772483945e-11 MLMG: Timers: Solve = 0.006560349 Iter = 0.006348539 Bottom = 0.000269911 Done calling nodal solver Timestep 12 ends with TIME = 0.03036043146 DT = 0.003262312503 Timing summary: Advection :0.009883956001 seconds MAC Proj :0.005274307 seconds Nodal Proj :0.007704317 seconds Reactions :0.015026076 seconds Misc :0.001663600001 seconds Base State :5.09999154e-08 seconds Time to advance time step: 0.039885149 Call to estdt for level 0 gives dt_lev = 4.177466111e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 13 gives dt =1e+20 dt_growth factor limits the new dt = 0.003425428128 Timestep 13 starts with TIME = 0.03036043146 DT = 0.003425428128 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.688771914e-30 MLMG: Initial residual (resid0) = 4.688771914e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.468299394e-40, 9.529786213e-11 MLMG: Timers: Solve = 0.004372971 Iter = 0.004163969 Bottom = 0.000162929 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.688771914e-30 MLMG: Initial residual (resid0) = 4.468299394e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000204974 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.971474721e-19 MLMG: Initial residual (resid0) = 1.971474721e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.494383217e-30, 1.772471734e-11 MLMG: Timers: Solve = 0.006246683 Iter = 0.006071037 Bottom = 0.000261627 Done calling nodal solver Timestep 13 ends with TIME = 0.03378585959 DT = 0.003425428128 Timing summary: Advection :0.006550776 seconds MAC Proj :0.005228085 seconds Nodal Proj :0.007018031 seconds Reactions :0.013171247 seconds Misc :0.002433938 seconds Base State :6.000027497e-08 seconds Time to advance time step: 0.034587959 Call to estdt for level 0 gives dt_lev = 3.982280624e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 14 gives dt =1e+20 dt_growth factor limits the new dt = 0.003596699534 Timestep 14 starts with TIME = 0.03378585959 DT = 0.003596699534 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.983088965e-30 MLMG: Initial residual (resid0) = 4.983088965e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.691428148e-40, 9.414698756e-11 MLMG: Timers: Solve = 0.004292216 Iter = 0.00407917 Bottom = 0.000164612 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.983088965e-30 MLMG: Initial residual (resid0) = 4.691428148e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000220531 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.221658729e-19 MLMG: Initial residual (resid0) = 2.221658729e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.863249975e-30, 3.989474107e-11 MLMG: Timers: Solve = 0.006389311 Iter = 0.00621142 Bottom = 0.000262315 Done calling nodal solver Timestep 14 ends with TIME = 0.03738255912 DT = 0.003596699534 Timing summary: Advection :0.006153896999 seconds MAC Proj :0.005134079 seconds Nodal Proj :0.0071452 seconds Reactions :0.012715925 seconds Misc :0.001568729999 seconds Base State :4.999992598e-08 seconds Time to advance time step: 0.032876115 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 15 gives dt =1e+20 dt_growth factor limits the new dt = 0.003776534511 Timestep 15 starts with TIME = 0.03738255912 DT = 0.003776534511 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 1.44706648e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 8.547886059e-31, 5.907044478e-11 MLMG: Timers: Solve = 0.004280801 Iter = 0.004075806 Bottom = 0.000162467 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 8.547886059e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000262173 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.279163939e-19 MLMG: Initial residual (resid0) = 2.279163939e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.500906095e-29, 6.585336268e-11 MLMG: Timers: Solve = 0.006210613 Iter = 0.006021152 Bottom = 0.000266591 Done calling nodal solver Timestep 15 ends with TIME = 0.04115909363 DT = 0.003776534511 Timing summary: Advection :0.006183255 seconds MAC Proj :0.00518161 seconds Nodal Proj :0.006968479 seconds Reactions :0.012346739 seconds Misc :0.001570803 seconds Base State :5.89998308e-08 seconds Time to advance time step: 0.032405297 Call to estdt for level 0 gives dt_lev = 9.044193233e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 16 gives dt =1e+20 dt_growth factor limits the new dt = 0.003965361236 Timestep 16 starts with TIME = 0.04115909363 DT = 0.003965361236 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 1.62270343e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.18702781e-31, 3.812790245e-11 MLMG: Timers: Solve = 0.004376872 Iter = 0.00418018 Bottom = 0.000163293 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 6.18702781e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000210887 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.282228424e-19 MLMG: Initial residual (resid0) = 2.282228424e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.045151033e-30, 1.772456688e-11 MLMG: Timers: Solve = 0.006258147 Iter = 0.006075075 Bottom = 0.000268668 Done calling nodal solver Timestep 16 ends with TIME = 0.04512445487 DT = 0.003965361236 Timing summary: Advection :0.005962349 seconds MAC Proj :0.005221079 seconds Nodal Proj :0.007024191 seconds Reactions :0.012266988 seconds Misc :0.001549656 seconds Base State :9.899986253e-08 seconds Time to advance time step: 0.032201271 Call to estdt for level 0 gives dt_lev = 3.436593485e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 17 gives dt =1e+20 dt_growth factor limits the new dt = 0.004163629298 Timestep 17 starts with TIME = 0.04512445487 DT = 0.004163629298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.754694364e-30 MLMG: Initial residual (resid0) = 3.754694364e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.825939058e-40, 7.526415691e-11 MLMG: Timers: Solve = 0.004400388 Iter = 0.004211715 Bottom = 0.00016814 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.754694364e-30 MLMG: Initial residual (resid0) = 2.825939058e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000202636 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.396339845e-19 MLMG: Initial residual (resid0) = 2.396339845e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.247301455e-30, 1.772411982e-11 MLMG: Timers: Solve = 0.006317301 Iter = 0.00612669 Bottom = 0.000259863 Done calling nodal solver Timestep 17 ends with TIME = 0.04928808417 DT = 0.004163629298 Timing summary: Advection :0.006032216 seconds MAC Proj :0.005233201 seconds Nodal Proj :0.007063219 seconds Reactions :0.012292599 seconds Misc :0.001620472 seconds Base State :8.000006346e-08 seconds Time to advance time step: 0.03240576 Call to estdt for level 0 gives dt_lev = 3.276898941e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 18 gives dt =1e+20 dt_growth factor limits the new dt = 0.004371810763 Timestep 18 starts with TIME = 0.04928808417 DT = 0.004371810763 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.989009514e-30 MLMG: Initial residual (resid0) = 5.989009514e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.702479003e-40, 9.521572791e-11 MLMG: Timers: Solve = 0.004341532 Iter = 0.004139264 Bottom = 0.00016674 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.989009514e-30 MLMG: Initial residual (resid0) = 5.702479003e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00021733 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.516156837e-19 MLMG: Initial residual (resid0) = 2.516156837e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.459755602e-30, 1.772447383e-11 MLMG: Timers: Solve = 0.00612294 Iter = 0.005951789 Bottom = 0.000262641 Done calling nodal solver Timestep 18 ends with TIME = 0.05365989493 DT = 0.004371810763 Timing summary: Advection :0.006221731001 seconds MAC Proj :0.005191588 seconds Nodal Proj :0.006884225 seconds Reactions :0.012380312 seconds Misc :0.001562268 seconds Base State :5.600031727e-08 seconds Time to advance time step: 0.032399444 Call to estdt for level 0 gives dt_lev = 3.122265826e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 19 gives dt =1e+20 dt_growth factor limits the new dt = 0.004590401301 Timestep 19 starts with TIME = 0.05365989493 DT = 0.004590401301 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.361324287e-30 MLMG: Initial residual (resid0) = 6.361324287e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.987979552e-40, 9.413102181e-11 MLMG: Timers: Solve = 0.004345582 Iter = 0.004132407 Bottom = 0.000165962 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.361324287e-30 MLMG: Initial residual (resid0) = 5.987979552e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000207715 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.641964679e-19 MLMG: Initial residual (resid0) = 2.641964679e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.682802363e-30, 1.772469708e-11 MLMG: Timers: Solve = 0.006401437 Iter = 0.006222044 Bottom = 0.000265737 Done calling nodal solver Timestep 19 ends with TIME = 0.05825029623 DT = 0.004590401301 Timing summary: Advection :0.006284744999 seconds MAC Proj :0.005193524999 seconds Nodal Proj :0.007153824 seconds Reactions :0.012290684 seconds Misc :0.001608828 seconds Base State :5.900028555e-08 seconds Time to advance time step: 0.032675866 Call to estdt for level 0 gives dt_lev = 2.974206455e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 20 gives dt =1e+20 dt_growth factor limits the new dt = 0.004819921366 Timestep 20 starts with TIME = 0.05825029623 DT = 0.004819921366 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.683696559e-30 MLMG: Initial residual (resid0) = 6.683696559e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.287226839e-40, 9.406810713e-11 MLMG: Timers: Solve = 0.004296992 Iter = 0.004089576 Bottom = 0.000164553 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.683696559e-30 MLMG: Initial residual (resid0) = 6.287226839e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000230325 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.774062913e-19 MLMG: Initial residual (resid0) = 2.774062913e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.916899148e-30, 1.772454087e-11 MLMG: Timers: Solve = 0.006483773 Iter = 0.006307747 Bottom = 0.000254963 Done calling nodal solver Timestep 20 ends with TIME = 0.0630702176 DT = 0.004819921366 Timing summary: Advection :0.006080866001 seconds MAC Proj :0.005147265 seconds Nodal Proj :0.007404388 seconds Reactions :0.012101553 seconds Misc :0.001535732 seconds Base State :5.100037015e-08 seconds Time to advance time step: 0.032470448 Call to estdt for level 0 gives dt_lev = 2.83287101e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 21 gives dt =1e+20 dt_growth factor limits the new dt = 0.005060917435 Timestep 21 starts with TIME = 0.0630702176 DT = 0.005060917435 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.019131084e-30 MLMG: Initial residual (resid0) = 7.019131084e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.601334897e-40, 9.40477506e-11 MLMG: Timers: Solve = 0.004372729 Iter = 0.004171944 Bottom = 0.000167711 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.019131084e-30 MLMG: Initial residual (resid0) = 6.601334897e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000201725 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.869691725e-19 MLMG: Initial residual (resid0) = 2.869691725e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.297839054e-29, 8.007267937e-11 MLMG: Timers: Solve = 0.006316658 Iter = 0.00613218 Bottom = 0.000255853 Done calling nodal solver Timestep 21 ends with TIME = 0.06813113503 DT = 0.005060917435 Timing summary: Advection :0.006226354999 seconds MAC Proj :0.005224165 seconds Nodal Proj :0.007112396 seconds Reactions :0.01290735 seconds Misc :0.001641156 seconds Base State :1.160001375e-07 seconds Time to advance time step: 0.033270452 Call to estdt for level 0 gives dt_lev = 5.895631152e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 22 gives dt =1e+20 dt_growth factor limits the new dt = 0.005313963306 Timestep 22 starts with TIME = 0.06813113503 DT = 0.005313963306 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 2.174577793e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 1.127461332e-30, 5.184736713e-11 MLMG: Timers: Solve = 0.004384083 Iter = 0.004179595 Bottom = 0.000163195 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 1.127461332e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.00019553 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.058404362e-19 MLMG: Initial residual (resid0) = 3.058404362e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.420866866e-30, 1.772449364e-11 MLMG: Timers: Solve = 0.006352255 Iter = 0.00617938 Bottom = 0.000255383 Done calling nodal solver Timestep 22 ends with TIME = 0.07344509834 DT = 0.005313963306 Timing summary: Advection :0.005945458 seconds MAC Proj :0.005233212 seconds Nodal Proj :0.007158063 seconds Reactions :0.012146856 seconds Misc :0.00149654 seconds Base State :5.800029612e-08 seconds Time to advance time step: 0.032123187 Call to estdt for level 0 gives dt_lev = 2.554672307e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 23 gives dt =1e+20 dt_growth factor limits the new dt = 0.005579661472 Timestep 23 starts with TIME = 0.07344509834 DT = 0.005579661472 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.733416233e-30 MLMG: Initial residual (resid0) = 7.733416233e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.972214945e-40, 7.722608954e-11 MLMG: Timers: Solve = 0.004359258 Iter = 0.004165927 Bottom = 0.000163687 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.733416233e-30 MLMG: Initial residual (resid0) = 5.972214945e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000198612 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.21132458e-19 MLMG: Initial residual (resid0) = 3.21132458e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.691941506e-30, 1.77245911e-11 MLMG: Timers: Solve = 0.006221744 Iter = 0.006045249 Bottom = 0.000264531 Done calling nodal solver Timestep 23 ends with TIME = 0.07902475981 DT = 0.005579661472 Timing summary: Advection :0.006067821 seconds MAC Proj :0.0052157 seconds Nodal Proj :0.007009371 seconds Reactions :0.012137816 seconds Misc :0.001577927 seconds Base State :5.399988368e-08 seconds Time to advance time step: 0.032146187 Call to estdt for level 0 gives dt_lev = 2.439853595e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 24 gives dt =1e+20 dt_growth factor limits the new dt = 0.005858644545 Timestep 24 starts with TIME = 0.07902475981 DT = 0.005858644545 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.005903751e-30 MLMG: Initial residual (resid0) = 8.005903751e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 7.641995188e-40, 9.54544974e-11 MLMG: Timers: Solve = 0.0043352 Iter = 0.004133871 Bottom = 0.000167396 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.005903751e-30 MLMG: Initial residual (resid0) = 7.641995188e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000204036 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.371890809e-19 MLMG: Initial residual (resid0) = 3.371890809e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.976497655e-30, 1.772446972e-11 MLMG: Timers: Solve = 0.00628968 Iter = 0.006104978 Bottom = 0.000250857 Done calling nodal solver Timestep 24 ends with TIME = 0.08488340435 DT = 0.005858644545 Timing summary: Advection :0.006208358 seconds MAC Proj :0.005202609 seconds Nodal Proj :0.007089665 seconds Reactions :0.012131706 seconds Misc :0.001546649 seconds Base State :5.399988368e-08 seconds Time to advance time step: 0.032312858 Call to estdt for level 0 gives dt_lev = 2.326594909e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 25 gives dt =1e+20 dt_growth factor limits the new dt = 0.006151576773 Timestep 25 starts with TIME = 0.08488340435 DT = 0.006151576773 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.528437685e-30 MLMG: Initial residual (resid0) = 8.528437685e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.023638825e-40, 9.408099257e-11 MLMG: Timers: Solve = 0.004359301 Iter = 0.00417036 Bottom = 0.000160086 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.528437685e-30 MLMG: Initial residual (resid0) = 8.023638825e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000194461 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.540485349e-19 MLMG: Initial residual (resid0) = 3.540485349e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.275401983e-30, 1.772469411e-11 MLMG: Timers: Solve = 0.00639003 Iter = 0.006205033 Bottom = 0.000257104 Done calling nodal solver Timestep 25 ends with TIME = 0.09103498113 DT = 0.006151576773 Timing summary: Advection :0.006196125999 seconds MAC Proj :0.005211451 seconds Nodal Proj :0.007173229 seconds Reactions :0.012196691 seconds Misc :0.001662357 seconds Base State :5.299989425e-08 seconds Time to advance time step: 0.032574857 Call to estdt for level 0 gives dt_lev = 2.217290439e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 26 gives dt =1e+20 dt_growth factor limits the new dt = 0.006459155611 Timestep 26 starts with TIME = 0.09103498113 DT = 0.006459155611 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.960898042e-30 MLMG: Initial residual (resid0) = 8.960898042e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.424494264e-40, 9.401395065e-11 MLMG: Timers: Solve = 0.004415805 Iter = 0.004227548 Bottom = 0.000162488 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.960898042e-30 MLMG: Initial residual (resid0) = 8.424494264e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.0001963 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.717509617e-19 MLMG: Initial residual (resid0) = 3.717509617e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.589087822e-30, 1.772446746e-11 MLMG: Timers: Solve = 0.006171854 Iter = 0.005991695 Bottom = 0.000243336 Done calling nodal solver Timestep 26 ends with TIME = 0.09749413674 DT = 0.006459155611 Timing summary: Advection :0.006098538 seconds MAC Proj :0.00524299 seconds Nodal Proj :0.006930621 seconds Reactions :0.012174519 seconds Misc :0.001512715 seconds Base State :5.799984137e-08 seconds Time to advance time step: 0.032100587 Call to estdt for level 0 gives dt_lev = 2.112523985e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 27 gives dt =1e+20 dt_growth factor limits the new dt = 0.006782113392 Timestep 27 starts with TIME = 0.09749413674 DT = 0.006782113392 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.409848931e-30 MLMG: Initial residual (resid0) = 9.409848931e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.845794647e-40, 9.400570308e-11 MLMG: Timers: Solve = 0.004356343 Iter = 0.004158268 Bottom = 0.000162295 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.409848931e-30 MLMG: Initial residual (resid0) = 8.845794647e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000202261 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.903385097e-19 MLMG: Initial residual (resid0) = 3.903385097e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.918614436e-30, 1.772465248e-11 MLMG: Timers: Solve = 0.0061553 Iter = 0.005972728 Bottom = 0.000251495 Done calling nodal solver Timestep 27 ends with TIME = 0.1042762501 DT = 0.006782113392 Timing summary: Advection :0.006293594 seconds MAC Proj :0.005194865 seconds Nodal Proj :0.006921904 seconds Reactions :0.012136303 seconds Misc :0.001724744 seconds Base State :5.800029612e-08 seconds Time to advance time step: 0.032410319 Call to estdt for level 0 gives dt_lev = 2.01240705e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 28 gives dt =1e+20 dt_growth factor limits the new dt = 0.007121219061 Timestep 28 starts with TIME = 0.1042762501 DT = 0.007121219061 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.87985185e-30 MLMG: Initial residual (resid0) = 9.87985185e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 9.288212598e-40, 9.401165867e-11 MLMG: Timers: Solve = 0.004345011 Iter = 0.004149012 Bottom = 0.000159463 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.87985185e-30 MLMG: Initial residual (resid0) = 9.288212598e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000206485 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.098554352e-19 MLMG: Initial residual (resid0) = 4.098554352e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.264463305e-30, 1.772445277e-11 MLMG: Timers: Solve = 0.006420637 Iter = 0.006246152 Bottom = 0.000247938 Done calling nodal solver Timestep 28 ends with TIME = 0.1113974692 DT = 0.007121219061 Timing summary: Advection :0.006158806 seconds MAC Proj :0.005192475 seconds Nodal Proj :0.007200659 seconds Reactions :0.012064972 seconds Misc :0.001502931 seconds Base State :5.599986252e-08 seconds Time to advance time step: 0.03226648 Call to estdt for level 0 gives dt_lev = 1.916892684e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 29 gives dt =1e+20 dt_growth factor limits the new dt = 0.007477280014 Timestep 29 starts with TIME = 0.1113974692 DT = 0.007477280014 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.037509187e-29 MLMG: Initial residual (resid0) = 1.037509187e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 9.752953234e-40, 9.400353609e-11 MLMG: Timers: Solve = 0.004371515 Iter = 0.004176182 Bottom = 0.000160481 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.037509187e-29 MLMG: Initial residual (resid0) = 9.752953234e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000208169 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.30348207e-19 MLMG: Initial residual (resid0) = 4.30348207e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.627789989e-30, 1.772469332e-11 MLMG: Timers: Solve = 0.006310726 Iter = 0.006129574 Bottom = 0.000248551 Done calling nodal solver Timestep 29 ends with TIME = 0.1188747492 DT = 0.007477280014 Timing summary: Advection :0.006139372 seconds MAC Proj :0.005219689 seconds Nodal Proj :0.007119852 seconds Reactions :0.01222801 seconds Misc :0.001503405999 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.032346349 Call to estdt for level 0 gives dt_lev = 1.825810886e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 30 gives dt =1e+20 dt_growth factor limits the new dt = 0.007851144015 Timestep 30 starts with TIME = 0.1188747492 DT = 0.007851144015 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.089501496e-29 MLMG: Initial residual (resid0) = 1.089501496e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.024106753e-39, 9.399773718e-11 MLMG: Timers: Solve = 0.004339226 Iter = 0.004146944 Bottom = 0.000160114 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.089501496e-29 MLMG: Initial residual (resid0) = 1.024106753e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000189755 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.518656173e-19 MLMG: Initial residual (resid0) = 4.518656173e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.00907597e-30, 1.772446423e-11 MLMG: Timers: Solve = 0.006184682 Iter = 0.006016009 Bottom = 0.000246086 Done calling nodal solver Timestep 30 ends with TIME = 0.1267258932 DT = 0.007851144015 Timing summary: Advection :0.006244149 seconds MAC Proj :0.0051857 seconds Nodal Proj :0.006943959 seconds Reactions :0.01214966 seconds Misc :0.001568300001 seconds Base State :5.699985195e-08 seconds Time to advance time step: 0.032225356 Call to estdt for level 0 gives dt_lev = 1.738995247e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 31 gives dt =1e+20 dt_growth factor limits the new dt = 0.008243701216 Timestep 31 starts with TIME = 0.1267258932 DT = 0.008243701216 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.144079624e-29 MLMG: Initial residual (resid0) = 1.144079624e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.075258351e-39, 9.398457314e-11 MLMG: Timers: Solve = 0.004356616 Iter = 0.004166645 Bottom = 0.000158997 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.144079624e-29 MLMG: Initial residual (resid0) = 1.075258351e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000208547 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.744588982e-19 MLMG: Initial residual (resid0) = 4.744588982e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.409669399e-30, 1.772475852e-11 MLMG: Timers: Solve = 0.006323513 Iter = 0.006121727 Bottom = 0.00025885 Done calling nodal solver Timestep 31 ends with TIME = 0.1349695944 DT = 0.008243701216 Timing summary: Advection :0.006308413 seconds MAC Proj :0.005200224 seconds Nodal Proj :0.007098704 seconds Reactions :0.012172671 seconds Misc :0.001529578001 seconds Base State :5.89998308e-08 seconds Time to advance time step: 0.032458395 Call to estdt for level 0 gives dt_lev = 1.656260551e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 32 gives dt =1e+20 dt_growth factor limits the new dt = 0.008655886277 Timestep 32 starts with TIME = 0.1349695944 DT = 0.008655886277 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.201372446e-29 MLMG: Initial residual (resid0) = 1.201372446e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.129010758e-39, 9.397674818e-11 MLMG: Timers: Solve = 0.004355656 Iter = 0.004165939 Bottom = 0.000163694 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.201372446e-29 MLMG: Initial residual (resid0) = 1.129010758e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000197031 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.981818431e-19 MLMG: Initial residual (resid0) = 4.981818431e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.830148054e-30, 1.772474886e-11 MLMG: Timers: Solve = 0.00625074 Iter = 0.006074448 Bottom = 0.000250697 Done calling nodal solver Timestep 32 ends with TIME = 0.1436254807 DT = 0.008655886277 Timing summary: Advection :0.006144125 seconds MAC Proj :0.005191638 seconds Nodal Proj :0.007016877 seconds Reactions :0.012190159 seconds Misc :0.001544388 seconds Base State :5.09999154e-08 seconds Time to advance time step: 0.032227522 Call to estdt for level 0 gives dt_lev = 1.577440861e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 33 gives dt =1e+20 dt_growth factor limits the new dt = 0.00908868059 Timestep 33 starts with TIME = 0.1436254807 DT = 0.00908868059 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.261567528e-29 MLMG: Initial residual (resid0) = 1.261567528e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.185462067e-39, 9.396738906e-11 MLMG: Timers: Solve = 0.004321801 Iter = 0.004130915 Bottom = 0.000162766 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.261567528e-29 MLMG: Initial residual (resid0) = 1.185462067e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000189833 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.230909353e-19 MLMG: Initial residual (resid0) = 5.230909353e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.271474901e-30, 1.772440368e-11 MLMG: Timers: Solve = 0.006252367 Iter = 0.006054949 Bottom = 0.000246769 Done calling nodal solver Timestep 33 ends with TIME = 0.1527141613 DT = 0.00908868059 Timing summary: Advection :0.006277602 seconds MAC Proj :0.005147915 seconds Nodal Proj :0.007041433 seconds Reactions :0.012074765 seconds Misc :0.001568386 seconds Base State :5.799984137e-08 seconds Time to advance time step: 0.032246986 Call to estdt for level 0 gives dt_lev = 1.502378414e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 34 gives dt =1e+20 dt_growth factor limits the new dt = 0.00954311462 Timestep 34 starts with TIME = 0.1527141613 DT = 0.00954311462 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.324582667e-29 MLMG: Initial residual (resid0) = 1.324582667e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.244696354e-39, 9.396894474e-11 MLMG: Timers: Solve = 0.004319124 Iter = 0.004131405 Bottom = 0.000161969 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.324582667e-29 MLMG: Initial residual (resid0) = 1.244696354e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000201392 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.49245482e-19 MLMG: Initial residual (resid0) = 5.49245482e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.735238831e-30, 1.772474995e-11 MLMG: Timers: Solve = 0.006243715 Iter = 0.00606396 Bottom = 0.00024757 Done calling nodal solver Timestep 34 ends with TIME = 0.1622572759 DT = 0.00954311462 Timing summary: Advection :0.006108888 seconds MAC Proj :0.005157497 seconds Nodal Proj :0.007008472 seconds Reactions :0.012110203 seconds Misc :0.001554014 seconds Base State :5.399988368e-08 seconds Time to advance time step: 0.032072638 Call to estdt for level 0 gives dt_lev = 1.430880358e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 35 gives dt =1e+20 dt_growth factor limits the new dt = 0.01002027035 Timestep 35 starts with TIME = 0.1622572759 DT = 0.01002027035 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.390963587e-29 MLMG: Initial residual (resid0) = 1.390963587e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.306904197e-39, 9.395675121e-11 MLMG: Timers: Solve = 0.004346983 Iter = 0.004148065 Bottom = 0.000162212 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.390963587e-29 MLMG: Initial residual (resid0) = 1.306904197e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000191388 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.681793327e-19 MLMG: Initial residual (resid0) = 5.681793327e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.54956653e-29, 8.00727212e-11 MLMG: Timers: Solve = 0.006323663 Iter = 0.006079513 Bottom = 0.000255308 Done calling nodal solver Timestep 35 ends with TIME = 0.1722775463 DT = 0.01002027035 Timing summary: Advection :0.006228377999 seconds MAC Proj :0.005190276 seconds Nodal Proj :0.007120125999 seconds Reactions :0.012130987 seconds Misc :0.001510466 seconds Base State :5.49998731e-08 seconds Time to advance time step: 0.03233333 Call to estdt for level 0 gives dt_lev = 2.977695677e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 36 gives dt =1e+20 dt_growth factor limits the new dt = 0.01052128387 Timestep 36 starts with TIME = 0.1722775463 DT = 0.01052128387 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 4.305515288e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.23205761e-30, 5.184182289e-11 MLMG: Timers: Solve = 0.004316833 Iter = 0.004126181 Bottom = 0.000163599 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 2.23205761e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000191941 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.055431439e-19 MLMG: Initial residual (resid0) = 6.055431439e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.073301499e-29, 1.772460822e-11 MLMG: Timers: Solve = 0.006277697 Iter = 0.006105007 Bottom = 0.000257258 Done calling nodal solver Timestep 36 ends with TIME = 0.1827988301 DT = 0.01052128387 Timing summary: Advection :0.005954063 seconds MAC Proj :0.005166427 seconds Nodal Proj :0.007072708 seconds Reactions :0.012145993 seconds Misc :0.001579878 seconds Base State :5.500032785e-08 seconds Time to advance time step: 0.032065099 Call to estdt for level 0 gives dt_lev = 1.290254218e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 37 gives dt =1e+20 dt_growth factor limits the new dt = 0.01104734806 Timestep 37 starts with TIME = 0.1827988301 DT = 0.01104734806 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.53169484e-29 MLMG: Initial residual (resid0) = 1.53169484e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.182368e-39, 7.719344411e-11 MLMG: Timers: Solve = 0.004340098 Iter = 0.004149556 Bottom = 0.000162883 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.53169484e-29 MLMG: Initial residual (resid0) = 1.182368e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000197474 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.264177143e-19 MLMG: Initial residual (resid0) = 6.264177143e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.855307908e-29, 7.75091093e-11 MLMG: Timers: Solve = 0.006224624 Iter = 0.006039576 Bottom = 0.000249296 Done calling nodal solver Timestep 37 ends with TIME = 0.1938461782 DT = 0.01104734806 Timing summary: Advection :0.006073913 seconds MAC Proj :0.005247293 seconds Nodal Proj :0.007020975 seconds Reactions :0.012432927 seconds Misc :0.001546561001 seconds Base State :5.09999154e-08 seconds Time to advance time step: 0.032488221 Call to estdt for level 0 gives dt_lev = 2.789559822e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 38 gives dt =1e+20 dt_growth factor limits the new dt = 0.01159971547 Timestep 38 starts with TIME = 0.1938461782 DT = 0.01159971547 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 4.746830605e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.490741235e-30, 5.247166883e-11 MLMG: Timers: Solve = 0.004305634 Iter = 0.004112894 Bottom = 0.000158158 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 2.490741235e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000201496 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.676113162e-19 MLMG: Initial residual (resid0) = 6.676113162e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.183315432e-29, 1.772461615e-11 MLMG: Timers: Solve = 0.006266596 Iter = 0.006091025 Bottom = 0.000265983 Done calling nodal solver Timestep 38 ends with TIME = 0.2054458937 DT = 0.01159971547 Timing summary: Advection :0.005821681999 seconds MAC Proj :0.005159439 seconds Nodal Proj :0.007021595 seconds Reactions :0.012067496 seconds Misc :0.001566188 seconds Base State :5.09999154e-08 seconds Time to advance time step: 0.03178065 Call to estdt for level 0 gives dt_lev = 1.168429834e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 39 gives dt =1e+20 dt_growth factor limits the new dt = 0.01217970124 Timestep 39 starts with TIME = 0.2054458937 DT = 0.01217970124 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.536277128e-29 MLMG: Initial residual (resid0) = 1.536277128e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.179416865e-39, 7.677110101e-11 MLMG: Timers: Solve = 0.004294237 Iter = 0.004106117 Bottom = 0.000160214 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.536277128e-29 MLMG: Initial residual (resid0) = 1.179416865e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000203491 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.00991882e-19 MLMG: Initial residual (resid0) = 7.00991882e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.242475185e-29, 1.77245303e-11 MLMG: Timers: Solve = 0.006182463 Iter = 0.006007539 Bottom = 0.000246563 Done calling nodal solver Timestep 39 ends with TIME = 0.2176255949 DT = 0.01217970124 Timing summary: Advection :0.006130440001 seconds MAC Proj :0.005138537 seconds Nodal Proj :0.006978844001 seconds Reactions :0.012571789 seconds Misc :0.001527527999 seconds Base State :5.800029612e-08 seconds Time to advance time step: 0.032482148 Call to estdt for level 0 gives dt_lev = 1.116506554e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 40 gives dt =1e+20 dt_growth factor limits the new dt = 0.0127886863 Timestep 40 starts with TIME = 0.2176255949 DT = 0.0127886863 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.750089547e-29 MLMG: Initial residual (resid0) = 1.750089547e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.668229006e-39, 9.532249417e-11 MLMG: Timers: Solve = 0.004382611 Iter = 0.004185409 Bottom = 0.000162242 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.750089547e-29 MLMG: Initial residual (resid0) = 1.668229006e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000190445 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.360414761e-19 MLMG: Initial residual (resid0) = 7.360414761e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.304586426e-29, 1.772436022e-11 MLMG: Timers: Solve = 0.006209229 Iter = 0.006023104 Bottom = 0.00024636 Done calling nodal solver Timestep 40 ends with TIME = 0.2304142812 DT = 0.0127886863 Timing summary: Advection :0.006186998 seconds MAC Proj :0.005211566 seconds Nodal Proj :0.007023005001 seconds Reactions :0.012130343 seconds Misc :0.001549619 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.032247984 Call to estdt for level 0 gives dt_lev = 1.065037272e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 41 gives dt =1e+20 dt_growth factor limits the new dt = 0.01342812062 Timestep 41 starts with TIME = 0.2304142812 DT = 0.01342812062 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.862969069e-29 MLMG: Initial residual (resid0) = 1.862969069e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.751653909e-39, 9.402485193e-11 MLMG: Timers: Solve = 0.004347396 Iter = 0.004157955 Bottom = 0.000159466 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.862969069e-29 MLMG: Initial residual (resid0) = 1.751653909e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000203373 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.728435499e-19 MLMG: Initial residual (resid0) = 7.728435499e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.369817673e-29, 1.772438514e-11 MLMG: Timers: Solve = 0.006324436 Iter = 0.00614014 Bottom = 0.000252581 Done calling nodal solver Timestep 41 ends with TIME = 0.2438424018 DT = 0.01342812062 Timing summary: Advection :0.006054161 seconds MAC Proj :0.005171858 seconds Nodal Proj :0.007083863 seconds Reactions :0.012273274 seconds Misc :0.001526771 seconds Base State :6.800019037e-08 seconds Time to advance time step: 0.032256338 Call to estdt for level 0 gives dt_lev = 1.015215791e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 42 gives dt =1e+20 dt_growth factor limits the new dt = 0.01409952665 Timestep 42 starts with TIME = 0.2438424018 DT = 0.01409952665 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.957338259e-29 MLMG: Initial residual (resid0) = 1.957338259e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.839075315e-39, 9.395797107e-11 MLMG: Timers: Solve = 0.004308952 Iter = 0.004119028 Bottom = 0.000162441 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.957338259e-29 MLMG: Initial residual (resid0) = 1.839075315e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000199416 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.114857274e-19 MLMG: Initial residual (resid0) = 8.114857274e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.43835189e-29, 1.772491914e-11 MLMG: Timers: Solve = 0.006258842 Iter = 0.006078532 Bottom = 0.0002442 Done calling nodal solver Timestep 42 ends with TIME = 0.2579419285 DT = 0.01409952665 Timing summary: Advection :0.006267549001 seconds MAC Proj :0.005143979 seconds Nodal Proj :0.007050848 seconds Reactions :0.012834862 seconds Misc :0.001528674999 seconds Base State :5.699985195e-08 seconds Time to advance time step: 0.032961637 Call to estdt for level 0 gives dt_lev = 9.67369433e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 43 gives dt =1e+20 dt_growth factor limits the new dt = 0.01480450298 Timestep 43 starts with TIME = 0.2579419285 DT = 0.01480450298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.055380727e-29 MLMG: Initial residual (resid0) = 2.055380727e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.931014507e-39, 9.394923682e-11 MLMG: Timers: Solve = 0.004633211 Iter = 0.004434097 Bottom = 0.000158912 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.055380727e-29 MLMG: Initial residual (resid0) = 1.931014507e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000187976 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.520600138e-19 MLMG: Initial residual (resid0) = 8.520600138e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.510227596e-29, 1.772442752e-11 MLMG: Timers: Solve = 0.006245445 Iter = 0.006055657 Bottom = 0.00027075 Done calling nodal solver Timestep 43 ends with TIME = 0.2727464314 DT = 0.01480450298 Timing summary: Advection :0.006163825 seconds MAC Proj :0.005469733 seconds Nodal Proj :0.007015989 seconds Reactions :0.012311526 seconds Misc :0.001565358999 seconds Base State :5.70003067e-08 seconds Time to advance time step: 0.032666201 Call to estdt for level 0 gives dt_lev = 9.21627116e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 44 gives dt =1e+20 dt_growth factor limits the new dt = 0.01554472813 Timestep 44 starts with TIME = 0.2727464314 DT = 0.01554472813 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.158317685e-29 MLMG: Initial residual (resid0) = 2.158317685e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.027620023e-39, 9.394446598e-11 MLMG: Timers: Solve = 0.004317945 Iter = 0.004124004 Bottom = 0.000160582 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.158317685e-29 MLMG: Initial residual (resid0) = 2.027620023e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000193131 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.946630145e-19 MLMG: Initial residual (resid0) = 8.946630145e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.585752938e-29, 1.772458359e-11 MLMG: Timers: Solve = 0.006299061 Iter = 0.006109329 Bottom = 0.000253591 Done calling nodal solver Timestep 44 ends with TIME = 0.2882911596 DT = 0.01554472813 Timing summary: Advection :0.006159057 seconds MAC Proj :0.005154828 seconds Nodal Proj :0.007118885 seconds Reactions :0.011912936 seconds Misc :0.001539354 seconds Base State :5.89998308e-08 seconds Time to advance time step: 0.032020349 Call to estdt for level 0 gives dt_lev = 8.779341895e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 45 gives dt =1e+20 dt_growth factor limits the new dt = 0.01632196453 Timestep 45 starts with TIME = 0.2882911596 DT = 0.01632196453 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.266393495e-29 MLMG: Initial residual (resid0) = 2.266393495e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.128720905e-39, 9.392547718e-11 MLMG: Timers: Solve = 0.004346584 Iter = 0.004147312 Bottom = 0.000159926 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.266393495e-29 MLMG: Initial residual (resid0) = 2.128720905e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000191138 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.053842861e-18 MLMG: Initial residual (resid0) = 1.053842861e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 6.6812532e-29, 6.339895109e-11 MLMG: Timers: Solve = 0.006212923 Iter = 0.006031967 Bottom = 0.000247599 Done calling nodal solver Timestep 45 ends with TIME = 0.3046131241 DT = 0.01632196453 Timing summary: Advection :0.006187763001 seconds MAC Proj :0.005166578 seconds Nodal Proj :0.006930805001 seconds Reactions :0.011889065 seconds Misc :0.001515999 seconds Base State :5.49998731e-08 seconds Time to advance time step: 0.031841006 Call to estdt for level 0 gives dt_lev = 2.02744569e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 46 gives dt =1e+20 dt_growth factor limits the new dt = 0.01713806276 Timestep 46 starts with TIME = 0.3046131241 DT = 0.01713806276 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 7.013230718e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.386529476e-30, 4.828772376e-11 MLMG: Timers: Solve = 0.004303888 Iter = 0.004111165 Bottom = 0.00016182 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 3.386529476e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000194936 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 9.863659735e-19 MLMG: Initial residual (resid0) = 9.863659735e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.748311055e-29, 1.772477054e-11 MLMG: Timers: Solve = 0.006270977 Iter = 0.006088493 Bottom = 0.00024581 Done calling nodal solver Timestep 46 ends with TIME = 0.3217511869 DT = 0.01713806276 Timing summary: Advection :0.005894016 seconds MAC Proj :0.005135871 seconds Nodal Proj :0.007030697 seconds Reactions :0.012111705 seconds Misc :0.001574071 seconds Base State :6.900017979e-08 seconds Time to advance time step: 0.031879793 Call to estdt for level 0 gives dt_lev = 7.924349732e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 47 gives dt =1e+20 dt_growth factor limits the new dt = 0.0179949659 Timestep 47 starts with TIME = 0.3217511869 DT = 0.0179949659 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.807852852e-29 MLMG: Initial residual (resid0) = 1.807852852e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.37289975e-39, 7.594090129e-11 MLMG: Timers: Solve = 0.004515021 Iter = 0.004169263 Bottom = 0.00015939 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.807852852e-29 MLMG: Initial residual (resid0) = 1.37289975e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000191483 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.035684272e-18 MLMG: Initial residual (resid0) = 1.035684272e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.835690497e-29, 1.772442188e-11 MLMG: Timers: Solve = 0.006317215 Iter = 0.006138597 Bottom = 0.000243693 Done calling nodal solver Timestep 47 ends with TIME = 0.3397461528 DT = 0.0179949659 Timing summary: Advection :0.006107975 seconds MAC Proj :0.005341954 seconds Nodal Proj :0.007098979 seconds Reactions :0.012618924 seconds Misc :0.001561351 seconds Base State :5.49998731e-08 seconds Time to advance time step: 0.032894951 Call to estdt for level 0 gives dt_lev = 7.566055076e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 48 gives dt =1e+20 dt_growth factor limits the new dt = 0.01889471419 Timestep 48 starts with TIME = 0.3397461528 DT = 0.01889471419 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.590190152e-29 MLMG: Initial residual (resid0) = 2.590190152e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.464371124e-39, 9.514247908e-11 MLMG: Timers: Solve = 0.004336642 Iter = 0.004145273 Bottom = 0.00017727 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.590190152e-29 MLMG: Initial residual (resid0) = 2.464371124e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000199578 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.087468486e-18 MLMG: Initial residual (resid0) = 1.087468486e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.927461059e-29, 1.772429348e-11 MLMG: Timers: Solve = 0.006221 Iter = 0.006041993 Bottom = 0.000247757 Done calling nodal solver Timestep 48 ends with TIME = 0.358640867 DT = 0.01889471419 Timing summary: Advection :0.00587627 seconds MAC Proj :0.005169379 seconds Nodal Proj :0.006984826 seconds Reactions :0.012076104 seconds Misc :0.00155887 seconds Base State :5.399988368e-08 seconds Time to advance time step: 0.031801546 Call to estdt for level 0 gives dt_lev = 7.214019049e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 49 gives dt =1e+20 dt_growth factor limits the new dt = 0.0198394499 Timestep 49 starts with TIME = 0.358640867 DT = 0.0198394499 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.753963702e-29 MLMG: Initial residual (resid0) = 2.753963702e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.587705007e-39, 9.396293077e-11 MLMG: Timers: Solve = 0.004308868 Iter = 0.004116584 Bottom = 0.000161894 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.753963702e-29 MLMG: Initial residual (resid0) = 2.587682586e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000192733 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.086359695e-18 MLMG: Initial residual (resid0) = 1.086359695e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 4.015978009e-29, 3.69672957e-11 MLMG: Timers: Solve = 0.006215946 Iter = 0.006029543 Bottom = 0.000250784 Done calling nodal solver Timestep 49 ends with TIME = 0.3784803169 DT = 0.0198394499 Timing summary: Advection :0.006027885 seconds MAC Proj :0.005158634 seconds Nodal Proj :0.006983671 seconds Reactions :0.012094021 seconds Misc :0.001544926 seconds Base State :5.09999154e-08 seconds Time to advance time step: 0.031955953 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 50 gives dt =1e+20 dt_growth factor limits the new dt = 0.0208314224 Timestep 50 starts with TIME = 0.3784803169 DT = 0.0208314224 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 8.242756114e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.779842146e-30, 4.585653262e-11 MLMG: Timers: Solve = 0.004341699 Iter = 0.00415153 Bottom = 0.000161837 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 3.779842146e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.00019684 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.198934006e-18 MLMG: Initial residual (resid0) = 1.198934006e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 2.12508073e-29, 1.772475149e-11 MLMG: Timers: Solve = 0.006267675 Iter = 0.006092024 Bottom = 0.000256401 Done calling nodal solver Timestep 50 ends with TIME = 0.3993117393 DT = 0.0208314224 Timing summary: Advection :0.00569395 seconds MAC Proj :0.005179678 seconds Nodal Proj :0.007022149 seconds Reactions :0.01202362 seconds Misc :0.00155194 seconds Base State :5.600031727e-08 seconds Time to advance time step: 0.031610367 Writing plotfile 50 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.015836543 Writing checkpoint 50 Writing checkpoint chk0000050 Total Time: 3.223815965 Unused ParmParse Variables: [TOP]::maestro.v(nvals = 1) :: [1] [TOP]::amr.check_file(nvals = 1) :: [test_stability_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] AMReX (23.07-7-g88f03408f18a) finalized