MPI initialized with 16 MPI processes MPI initialized with thread support level 0 AMReX (23.08-31-g435281069858) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = 5peaks_const_grav.dat model file = 5peaks_const_grav.dat reading initial model 1000 points found in the initial model 10 variables found in the initial model WARNING: variable not found: gravity WARNING: variable not found: abar WARNING: variable not found: zbar WARNING: variable not found: gpot WARNING: variable not found: cno model file mapping, level: 0 dr of MAESTRO base state = 93750000.000000 dr of input file data = 10010010.010010 maximum radius (cell-centered) of input model = 10000000000.000000 WARNING: resolution of base state array is not an integer multiple of the initial model's resolution. make sure this is a desired property as this could lead to aliasing when performing the interpolation. modulus = 3659909.909910 setting r_cutoff to 105 radius at r_cutoff 9890625000 Maximum HSE Error = 0.054171 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile test_stability_pltInitData after InitData inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.017177125 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.000191767 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile test_stability_pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.015390164 Call to firstdt for level 0 gives dt_lev = 0.01907406555 Multiplying dt_lev by init_shrink; dt_lev = 0.001907406555 Minimum firstdt over all levels = 0.001907406555 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 4.945354899e-27 MLMG: Initial residual (resid0) = 4.945354899e-27 MLMG: Final Iter. 3 resid, resid/bnorm = 2.357566962e-30, 0.0004767235133 MLMG: Timers: Solve = 0.002471119 Iter = 0.002262375 Bottom = 8.8331e-05 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 1 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #2 Calling nodal solver MLMG: Initial rhs = 2.306075226e-30 MLMG: Initial residual (resid0) = 2.306075226e-30 MLMG: Final Iter. 5 resid, resid/bnorm = 1.933632021e-37, 8.384947719e-08 MLMG: Timers: Solve = 0.003688135 Iter = 0.003493247 Bottom = 0.00014706 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 2 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #3 Calling nodal solver MLMG: Initial rhs = 9.742172191e-32 MLMG: Initial residual (resid0) = 9.742172191e-32 MLMG: Final Iter. 4 resid, resid/bnorm = 7.521071013e-41, 7.720117101e-10 MLMG: Timers: Solve = 0.002992918 Iter = 0.002817143 Bottom = 0.000110362 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 3 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Writing plotfile test_stability_pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.013493071 Doing initial pressure iteration #1 Timestep 0 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.893547601e-20 MLMG: Initial residual (resid0) = 4.893547601e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 4.517319815e-31, 9.231175792e-12 MLMG: Timers: Solve = 0.004144003 Iter = 0.003911941 Bottom = 0.000155222 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.893547507e-20 MLMG: Initial residual (resid0) = 2.477484298e-27 MLMG: Final Iter. 4 resid, resid/bnorm = 4.813594311e-30, 9.836615062e-11 MLMG: Timers: Solve = 0.001866649 Iter = 0.001633809 Bottom = 6.675e-05 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.755411273e-17 MLMG: Initial residual (resid0) = 5.755411273e-17 MLMG: Final Iter. 9 resid, resid/bnorm = 1.02012041e-27, 1.772454411e-11 MLMG: Timers: Solve = 0.006262579 Iter = 0.006041331 Bottom = 0.000250431 Done calling nodal solver Timestep 0 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.006634022 seconds MAC Proj :0.006738119 seconds Nodal Proj :0.006987911 seconds Reactions :0.012542126 seconds Misc :0.001559485 seconds Base State :1.009998414e-07 seconds Time to advance time step: 0.037889445 Writing plotfile 0 after all initialization inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.014082783 Writing checkpoint 0 after all initialization Writing checkpoint chk0000000 Calling Evolve() Timestep 1 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.257776127e-26 MLMG: Initial residual (resid0) = 1.257776127e-26 MLMG: Final Iter. 10 resid, resid/bnorm = 1.092411925e-37, 8.685265223e-12 MLMG: Timers: Solve = 0.006458652 Iter = 0.006091637 Bottom = 0.000158004 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.257776127e-26 MLMG: Initial residual (resid0) = 1.092411925e-37 MLMG: No iterations needed MLMG: Timers: Solve = 0.00035012 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.097790919e-19 MLMG: Initial residual (resid0) = 1.097790919e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.945791097e-30, 1.772460551e-11 MLMG: Timers: Solve = 0.008306908 Iter = 0.007950762 Bottom = 0.000243727 Done calling nodal solver Timestep 1 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.00979022 seconds MAC Proj :0.007666705 seconds Nodal Proj :0.009414992 seconds Reactions :0.022170596 seconds Misc :0.002501609 seconds Base State :9.699988368e-08 seconds Time to advance time step: 0.058147754 Call to estdt for level 0 gives dt_lev = 7.191081337e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 2 gives dt =1e+20 dt_growth factor limits the new dt = 0.002002776883 Timestep 2 starts with TIME = 0.001907406555 DT = 0.002002776883 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.080398705e-27 MLMG: Initial residual (resid0) = 8.080398705e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 1.160441939e-37, 1.436119654e-11 MLMG: Timers: Solve = 0.006250365 Iter = 0.005903343 Bottom = 0.000154946 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.498306209e-27 MLMG: Initial residual (resid0) = 2.601349809e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 8.688832515e-37, 9.14777048e-11 MLMG: Timers: Solve = 0.006252477 Iter = 0.005903835 Bottom = 0.000160689 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.096671578e-19 MLMG: Initial residual (resid0) = 1.096671578e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.008844235e-29, 9.19914635e-11 MLMG: Timers: Solve = 0.007858381 Iter = 0.007492985 Bottom = 0.000247265 Done calling nodal solver Timestep 2 ends with TIME = 0.003910183437 DT = 0.002002776883 Timing summary: Advection :0.009481873 seconds MAC Proj :0.013416178 seconds Nodal Proj :0.008858191 seconds Reactions :0.022323371 seconds Misc :0.002313769 seconds Base State :8.300003174e-08 seconds Time to advance time step: 0.056545444 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 3 gives dt =1e+20 dt_growth factor limits the new dt = 0.002102915727 Timestep 3 starts with TIME = 0.003910183437 DT = 0.002102915727 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 8.320997544e-21 MLMG: Final Iter. 10 resid, resid/bnorm = 7.676109766e-31, 9.22498742e-11 MLMG: Timers: Solve = 0.004327129 Iter = 0.0040987 Bottom = 0.000152633 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 7.676109766e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022534 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.21031446e-19 MLMG: Initial residual (resid0) = 1.21031446e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.145209106e-30, 1.772439458e-11 MLMG: Timers: Solve = 0.006226893 Iter = 0.006039403 Bottom = 0.000271487 Done calling nodal solver Timestep 3 ends with TIME = 0.006013099164 DT = 0.002102915727 Timing summary: Advection :0.005769269 seconds MAC Proj :0.005231434 seconds Nodal Proj :0.006972944 seconds Reactions :0.013039304 seconds Misc :0.001534282 seconds Base State :4.80001745e-08 seconds Time to advance time step: 0.032689249 Call to estdt for level 0 gives dt_lev = 6.528630569e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 4 gives dt =1e+20 dt_growth factor limits the new dt = 0.002208061513 Timestep 4 starts with TIME = 0.006013099164 DT = 0.002208061513 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.308039747e-29 MLMG: Initial residual (resid0) = 1.308039747e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.129752045e-39, 8.636985596e-11 MLMG: Timers: Solve = 0.004126733 Iter = 0.00387122 Bottom = 0.000151572 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.308039747e-29 MLMG: Initial residual (resid0) = 1.129752045e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000222338 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.270830183e-19 MLMG: Initial residual (resid0) = 1.270830183e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.252495441e-30, 1.772459822e-11 MLMG: Timers: Solve = 0.006070936 Iter = 0.005867574 Bottom = 0.000245039 Done calling nodal solver Timestep 4 ends with TIME = 0.008221160677 DT = 0.002208061513 Timing summary: Advection :0.005908872 seconds MAC Proj :0.004998785 seconds Nodal Proj :0.006826834 seconds Reactions :0.012638024 seconds Misc :0.001660813 seconds Base State :7.099993127e-08 seconds Time to advance time step: 0.032183404 Call to estdt for level 0 gives dt_lev = 6.226258359e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 5 gives dt =1e+20 dt_growth factor limits the new dt = 0.002318464589 Timestep 5 starts with TIME = 0.008221160677 DT = 0.002318464589 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.295923274e-30 MLMG: Initial residual (resid0) = 3.295923274e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.024366424e-40, 9.176082608e-11 MLMG: Timers: Solve = 0.004030901 Iter = 0.003811545 Bottom = 0.000153986 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.295923274e-30 MLMG: Initial residual (resid0) = 3.024366424e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000223152 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.334371692e-19 MLMG: Initial residual (resid0) = 1.334371692e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.365138268e-30, 1.772473353e-11 MLMG: Timers: Solve = 0.00602014 Iter = 0.005835489 Bottom = 0.000240484 Done calling nodal solver Timestep 5 ends with TIME = 0.01053962527 DT = 0.002318464589 Timing summary: Advection :0.006024782 seconds MAC Proj :0.004909459 seconds Nodal Proj :0.00675492 seconds Reactions :0.012065051 seconds Misc :0.001536139 seconds Base State :4.999992598e-08 seconds Time to advance time step: 0.031427281 Call to estdt for level 0 gives dt_lev = 5.915049504e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 6 gives dt =1e+20 dt_growth factor limits the new dt = 0.002434387818 Timestep 6 starts with TIME = 0.01053962527 DT = 0.002434387818 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.377753945e-30 MLMG: Initial residual (resid0) = 3.377753945e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.175503469e-40, 9.401227921e-11 MLMG: Timers: Solve = 0.004003177 Iter = 0.003778516 Bottom = 0.000157693 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.377753945e-30 MLMG: Initial residual (resid0) = 3.175499966e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000230413 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.401090277e-19 MLMG: Initial residual (resid0) = 1.401090277e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.483342219e-30, 1.772435552e-11 MLMG: Timers: Solve = 0.006068422 Iter = 0.005890236 Bottom = 0.000242985 Done calling nodal solver Timestep 6 ends with TIME = 0.01297401308 DT = 0.002434387818 Timing summary: Advection :0.006178782 seconds MAC Proj :0.004893957 seconds Nodal Proj :0.006815546 seconds Reactions :0.012032642 seconds Misc :0.001556052 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.031614536 Call to estdt for level 0 gives dt_lev = 5.625515433e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 7 gives dt =1e+20 dt_growth factor limits the new dt = 0.002556107209 Timestep 7 starts with TIME = 0.01297401308 DT = 0.002556107209 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.543159178e-30 MLMG: Initial residual (resid0) = 3.543159178e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.334123449e-40, 9.410030095e-11 MLMG: Timers: Solve = 0.004143763 Iter = 0.003924033 Bottom = 0.000156233 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.543159178e-30 MLMG: Initial residual (resid0) = 3.334123449e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000225647 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.471144791e-19 MLMG: Initial residual (resid0) = 1.471144791e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.607516552e-30, 1.772440461e-11 MLMG: Timers: Solve = 0.00611577 Iter = 0.005879109 Bottom = 0.00024429 Done calling nodal solver Timestep 7 ends with TIME = 0.01553012029 DT = 0.002556107209 Timing summary: Advection :0.005897264 seconds MAC Proj :0.005023548 seconds Nodal Proj :0.006869892 seconds Reactions :0.011862698 seconds Misc :0.001602798 seconds Base State :1.409998731e-07 seconds Time to advance time step: 0.031396124 Call to estdt for level 0 gives dt_lev = 5.353255202e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 8 gives dt =1e+20 dt_growth factor limits the new dt = 0.002683912569 Timestep 8 starts with TIME = 0.01553012029 DT = 0.002683912569 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.720271341e-30 MLMG: Initial residual (resid0) = 3.720271341e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.500226363e-40, 9.408524384e-11 MLMG: Timers: Solve = 0.004018947 Iter = 0.003804722 Bottom = 0.000155822 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.720271341e-30 MLMG: Initial residual (resid0) = 3.500226363e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00021522 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.54470203e-19 MLMG: Initial residual (resid0) = 1.54470203e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.737914046e-30, 1.772454488e-11 MLMG: Timers: Solve = 0.00608244 Iter = 0.005898242 Bottom = 0.000260572 Done calling nodal solver Timestep 8 ends with TIME = 0.01821403286 DT = 0.002683912569 Timing summary: Advection :0.006252002 seconds MAC Proj :0.00487014 seconds Nodal Proj :0.00682445 seconds Reactions :0.011796344 seconds Misc :0.001528359 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.031420534 Call to estdt for level 0 gives dt_lev = 5.095618567e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 9 gives dt =1e+20 dt_growth factor limits the new dt = 0.002818108198 Timestep 9 starts with TIME = 0.01821403286 DT = 0.002818108198 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.90613533e-30 MLMG: Initial residual (resid0) = 3.90613533e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.675781034e-40, 9.410275692e-11 MLMG: Timers: Solve = 0.006031624 Iter = 0.004680427 Bottom = 0.000170704 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.90613533e-30 MLMG: Initial residual (resid0) = 3.675781034e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000262813 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.621937132e-19 MLMG: Initial residual (resid0) = 1.621937132e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.874835628e-30, 1.772470444e-11 MLMG: Timers: Solve = 0.006672347 Iter = 0.006451276 Bottom = 0.000244336 Done calling nodal solver Timestep 9 ends with TIME = 0.02103214106 DT = 0.002818108198 Timing summary: Advection :0.009782902 seconds MAC Proj :0.006999768 seconds Nodal Proj :0.007624701 seconds Reactions :0.013360096 seconds Misc :0.001602254 seconds Base State :9.100017451e-08 seconds Time to advance time step: 0.039625815 Call to estdt for level 0 gives dt_lev = 4.851290067e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 10 gives dt =1e+20 dt_growth factor limits the new dt = 0.002959013608 Timestep 10 starts with TIME = 0.02103214106 DT = 0.002959013608 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.101240383e-30 MLMG: Initial residual (resid0) = 4.101240383e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.859393172e-40, 9.410307155e-11 MLMG: Timers: Solve = 0.00409025 Iter = 0.00386682 Bottom = 0.000155705 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.101240383e-30 MLMG: Initial residual (resid0) = 3.859393172e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000232316 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.703033988e-19 MLMG: Initial residual (resid0) = 1.703033988e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.174814859e-29, 6.898364135e-11 MLMG: Timers: Solve = 0.006115887 Iter = 0.005890645 Bottom = 0.000268388 Done calling nodal solver Timestep 10 ends with TIME = 0.02399115467 DT = 0.002959013608 Timing summary: Advection :0.006243138 seconds MAC Proj :0.005000253 seconds Nodal Proj :0.006884195 seconds Reactions :0.012598582 seconds Misc :0.001771902 seconds Base State :7.099993127e-08 seconds Time to advance time step: 0.032652133 Call to estdt for level 0 gives dt_lev = 1.153498162e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 11 gives dt =1e+20 dt_growth factor limits the new dt = 0.003106964288 Timestep 11 starts with TIME = 0.02399115467 DT = 0.003106964288 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 1.271430598e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.310137768e-31, 4.963021794e-11 MLMG: Timers: Solve = 0.004030756 Iter = 0.003818348 Bottom = 0.000154374 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 6.310137768e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000210449 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.788185688e-19 MLMG: Initial residual (resid0) = 1.788185688e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.169478835e-30, 1.772455096e-11 MLMG: Timers: Solve = 0.00616096 Iter = 0.005948279 Bottom = 0.000250657 Done calling nodal solver Timestep 11 ends with TIME = 0.02709811896 DT = 0.003106964288 Timing summary: Advection :0.005757441 seconds MAC Proj :0.00491715 seconds Nodal Proj :0.006910836 seconds Reactions :0.011993651 seconds Misc :0.001545433 seconds Base State :2.159999895e-07 seconds Time to advance time step: 0.031261582 Call to estdt for level 0 gives dt_lev = 4.376664086e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 12 gives dt =1e+20 dt_growth factor limits the new dt = 0.003262312503 Timestep 12 starts with TIME = 0.02709811896 DT = 0.003262312503 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.931483508e-30 MLMG: Initial residual (resid0) = 2.931483508e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.211723667e-40, 7.544724916e-11 MLMG: Timers: Solve = 0.004041707 Iter = 0.003826942 Bottom = 0.000157438 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.931483508e-30 MLMG: Initial residual (resid0) = 2.211723667e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000213557 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.877594972e-19 MLMG: Initial residual (resid0) = 1.877594972e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.328006944e-30, 1.772483945e-11 MLMG: Timers: Solve = 0.00593954 Iter = 0.005762035 Bottom = 0.000241931 Done calling nodal solver Timestep 12 ends with TIME = 0.03036043146 DT = 0.003262312503 Timing summary: Advection :0.005900404 seconds MAC Proj :0.004943987 seconds Nodal Proj :0.006714001 seconds Reactions :0.011990754 seconds Misc :0.001503101 seconds Base State :4.80001745e-08 seconds Time to advance time step: 0.031187111 Call to estdt for level 0 gives dt_lev = 4.177466111e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 13 gives dt =1e+20 dt_growth factor limits the new dt = 0.003425428128 Timestep 13 starts with TIME = 0.03036043146 DT = 0.003425428128 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.688771914e-30 MLMG: Initial residual (resid0) = 4.688771914e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.468299394e-40, 9.529786213e-11 MLMG: Timers: Solve = 0.004106483 Iter = 0.003900379 Bottom = 0.000207057 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.688771914e-30 MLMG: Initial residual (resid0) = 4.468299394e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000205046 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.971474721e-19 MLMG: Initial residual (resid0) = 1.971474721e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.494383217e-30, 1.772471734e-11 MLMG: Timers: Solve = 0.006107973 Iter = 0.005857083 Bottom = 0.000245612 Done calling nodal solver Timestep 13 ends with TIME = 0.03378585959 DT = 0.003425428128 Timing summary: Advection :0.006048794 seconds MAC Proj :0.004974804 seconds Nodal Proj :0.006856935 seconds Reactions :0.011979609 seconds Misc :0.001559258 seconds Base State :4.80001745e-08 seconds Time to advance time step: 0.031557109 Call to estdt for level 0 gives dt_lev = 3.982280624e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 14 gives dt =1e+20 dt_growth factor limits the new dt = 0.003596699534 Timestep 14 starts with TIME = 0.03378585959 DT = 0.003596699534 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.983088965e-30 MLMG: Initial residual (resid0) = 4.983088965e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.691428148e-40, 9.414698756e-11 MLMG: Timers: Solve = 0.004046567 Iter = 0.003842865 Bottom = 0.000183487 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.983088965e-30 MLMG: Initial residual (resid0) = 4.691428148e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000199129 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.221658729e-19 MLMG: Initial residual (resid0) = 2.221658729e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.863249975e-30, 3.989474107e-11 MLMG: Timers: Solve = 0.006005745 Iter = 0.005826358 Bottom = 0.000242183 Done calling nodal solver Timestep 14 ends with TIME = 0.03738255912 DT = 0.003596699534 Timing summary: Advection :0.005971784 seconds MAC Proj :0.004901727 seconds Nodal Proj :0.006738997 seconds Reactions :0.012074958 seconds Misc :0.001529315 seconds Base State :2.990000212e-07 seconds Time to advance time step: 0.03135943 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 15 gives dt =1e+20 dt_growth factor limits the new dt = 0.003776534511 Timestep 15 starts with TIME = 0.03738255912 DT = 0.003776534511 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 1.44706648e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 8.547886059e-31, 5.907044478e-11 MLMG: Timers: Solve = 0.004068097 Iter = 0.003870151 Bottom = 0.000157559 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 8.547886059e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000198602 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.279163939e-19 MLMG: Initial residual (resid0) = 2.279163939e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.500906095e-29, 6.585336268e-11 MLMG: Timers: Solve = 0.006193615 Iter = 0.006012677 Bottom = 0.000268703 Done calling nodal solver Timestep 15 ends with TIME = 0.04115909363 DT = 0.003776534511 Timing summary: Advection :0.005745228 seconds MAC Proj :0.004949917 seconds Nodal Proj :0.006918166 seconds Reactions :0.011841624 seconds Misc :0.001535138 seconds Base State :4.999992598e-08 seconds Time to advance time step: 0.031122875 Call to estdt for level 0 gives dt_lev = 9.044193233e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 16 gives dt =1e+20 dt_growth factor limits the new dt = 0.003965361236 Timestep 16 starts with TIME = 0.04115909363 DT = 0.003965361236 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 1.62270343e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.18702781e-31, 3.812790245e-11 MLMG: Timers: Solve = 0.004014848 Iter = 0.003806802 Bottom = 0.000153127 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 6.18702781e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000199169 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.282228424e-19 MLMG: Initial residual (resid0) = 2.282228424e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.045151033e-30, 1.772456688e-11 MLMG: Timers: Solve = 0.006016405 Iter = 0.005804234 Bottom = 0.000242655 Done calling nodal solver Timestep 16 ends with TIME = 0.04512445487 DT = 0.003965361236 Timing summary: Advection :0.005715231 seconds MAC Proj :0.00490515 seconds Nodal Proj :0.006758403 seconds Reactions :0.01262101 seconds Misc :0.001539313 seconds Base State :5.100014278e-08 seconds Time to advance time step: 0.03167319 Call to estdt for level 0 gives dt_lev = 3.436593485e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 17 gives dt =1e+20 dt_growth factor limits the new dt = 0.004163629298 Timestep 17 starts with TIME = 0.04512445487 DT = 0.004163629298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.754694364e-30 MLMG: Initial residual (resid0) = 3.754694364e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.825939058e-40, 7.526415691e-11 MLMG: Timers: Solve = 0.004090232 Iter = 0.003892683 Bottom = 0.00016759 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.754694364e-30 MLMG: Initial residual (resid0) = 2.825939058e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000212274 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.396339845e-19 MLMG: Initial residual (resid0) = 2.396339845e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.247301455e-30, 1.772411982e-11 MLMG: Timers: Solve = 0.006029325 Iter = 0.005863358 Bottom = 0.000243549 Done calling nodal solver Timestep 17 ends with TIME = 0.04928808417 DT = 0.004163629298 Timing summary: Advection :0.005919206 seconds MAC Proj :0.004959257 seconds Nodal Proj :0.006797088 seconds Reactions :0.011997855 seconds Misc :0.001588834 seconds Base State :5.09999154e-08 seconds Time to advance time step: 0.031400881 Call to estdt for level 0 gives dt_lev = 3.276898941e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 18 gives dt =1e+20 dt_growth factor limits the new dt = 0.004371810763 Timestep 18 starts with TIME = 0.04928808417 DT = 0.004371810763 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.989009514e-30 MLMG: Initial residual (resid0) = 5.989009514e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.702479003e-40, 9.521572791e-11 MLMG: Timers: Solve = 0.00406259 Iter = 0.003861887 Bottom = 0.000155612 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.989009514e-30 MLMG: Initial residual (resid0) = 5.702479003e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00021663 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.516156837e-19 MLMG: Initial residual (resid0) = 2.516156837e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.459755602e-30, 1.772447383e-11 MLMG: Timers: Solve = 0.005980586 Iter = 0.005801688 Bottom = 0.000242428 Done calling nodal solver Timestep 18 ends with TIME = 0.05365989493 DT = 0.004371810763 Timing summary: Advection :0.006015511 seconds MAC Proj :0.004917063 seconds Nodal Proj :0.006729108 seconds Reactions :0.012796637 seconds Misc :0.001519505 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.032124885 Call to estdt for level 0 gives dt_lev = 3.122265826e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 19 gives dt =1e+20 dt_growth factor limits the new dt = 0.004590401301 Timestep 19 starts with TIME = 0.05365989493 DT = 0.004590401301 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.361324287e-30 MLMG: Initial residual (resid0) = 6.361324287e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.987979552e-40, 9.413102181e-11 MLMG: Timers: Solve = 0.004058279 Iter = 0.003796543 Bottom = 0.000154203 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.361324287e-30 MLMG: Initial residual (resid0) = 5.987979552e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000212458 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.641964679e-19 MLMG: Initial residual (resid0) = 2.641964679e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.682802363e-30, 1.772469708e-11 MLMG: Timers: Solve = 0.006201302 Iter = 0.005975454 Bottom = 0.000279803 Done calling nodal solver Timestep 19 ends with TIME = 0.05825029623 DT = 0.004590401301 Timing summary: Advection :0.006090984 seconds MAC Proj :0.00492377 seconds Nodal Proj :0.006951346 seconds Reactions :0.011951749 seconds Misc :0.001543916 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.031607285 Call to estdt for level 0 gives dt_lev = 2.974206455e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 20 gives dt =1e+20 dt_growth factor limits the new dt = 0.004819921366 Timestep 20 starts with TIME = 0.05825029623 DT = 0.004819921366 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.683696559e-30 MLMG: Initial residual (resid0) = 6.683696559e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.287226839e-40, 9.406810713e-11 MLMG: Timers: Solve = 0.004022298 Iter = 0.003816431 Bottom = 0.000153374 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.683696559e-30 MLMG: Initial residual (resid0) = 6.287226839e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000212157 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.774062913e-19 MLMG: Initial residual (resid0) = 2.774062913e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.916899148e-30, 1.772454087e-11 MLMG: Timers: Solve = 0.006374848 Iter = 0.006164751 Bottom = 0.000255497 Done calling nodal solver Timestep 20 ends with TIME = 0.0630702176 DT = 0.004819921366 Timing summary: Advection :0.006156529 seconds MAC Proj :0.004880983 seconds Nodal Proj :0.007125478 seconds Reactions :0.012616171 seconds Misc :0.001549063 seconds Base State :5.300012162e-08 seconds Time to advance time step: 0.032480801 Call to estdt for level 0 gives dt_lev = 2.83287101e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 21 gives dt =1e+20 dt_growth factor limits the new dt = 0.005060917435 Timestep 21 starts with TIME = 0.0630702176 DT = 0.005060917435 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.019131084e-30 MLMG: Initial residual (resid0) = 7.019131084e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.601334897e-40, 9.40477506e-11 MLMG: Timers: Solve = 0.004011252 Iter = 0.003819723 Bottom = 0.000152571 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.019131084e-30 MLMG: Initial residual (resid0) = 6.601334897e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000204681 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.869691725e-19 MLMG: Initial residual (resid0) = 2.869691725e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.297839054e-29, 8.007267937e-11 MLMG: Timers: Solve = 0.00591419 Iter = 0.005732417 Bottom = 0.000245748 Done calling nodal solver Timestep 21 ends with TIME = 0.06813113503 DT = 0.005060917435 Timing summary: Advection :0.006043068 seconds MAC Proj :0.004866943 seconds Nodal Proj :0.006645852 seconds Reactions :0.012433018 seconds Misc :0.001538041 seconds Base State :6.799996299e-08 seconds Time to advance time step: 0.031669253 Call to estdt for level 0 gives dt_lev = 5.895631152e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 22 gives dt =1e+20 dt_growth factor limits the new dt = 0.005313963306 Timestep 22 starts with TIME = 0.06813113503 DT = 0.005313963306 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 2.174577793e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 1.127461332e-30, 5.184736713e-11 MLMG: Timers: Solve = 0.004094111 Iter = 0.003891382 Bottom = 0.000152045 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 1.127461332e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000270802 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.058404362e-19 MLMG: Initial residual (resid0) = 3.058404362e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.420866866e-30, 1.772449364e-11 MLMG: Timers: Solve = 0.006448305 Iter = 0.006234581 Bottom = 0.000293721 Done calling nodal solver Timestep 22 ends with TIME = 0.07344509834 DT = 0.005313963306 Timing summary: Advection :0.00577335 seconds MAC Proj :0.00505021 seconds Nodal Proj :0.007217576 seconds Reactions :0.012071467 seconds Misc :0.001530838 seconds Base State :9.099994713e-08 seconds Time to advance time step: 0.031794914 Call to estdt for level 0 gives dt_lev = 2.554672307e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 23 gives dt =1e+20 dt_growth factor limits the new dt = 0.005579661472 Timestep 23 starts with TIME = 0.07344509834 DT = 0.005579661472 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.733416233e-30 MLMG: Initial residual (resid0) = 7.733416233e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.972214945e-40, 7.722608954e-11 MLMG: Timers: Solve = 0.003974155 Iter = 0.003767913 Bottom = 0.000153604 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.733416233e-30 MLMG: Initial residual (resid0) = 5.972214945e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000208527 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.21132458e-19 MLMG: Initial residual (resid0) = 3.21132458e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.691941506e-30, 1.77245911e-11 MLMG: Timers: Solve = 0.005957526 Iter = 0.005763348 Bottom = 0.000248394 Done calling nodal solver Timestep 23 ends with TIME = 0.07902475981 DT = 0.005579661472 Timing summary: Advection :0.005978474 seconds MAC Proj :0.004860614 seconds Nodal Proj :0.00671197 seconds Reactions :0.011873967 seconds Misc :0.001529331 seconds Base State :4.999992598e-08 seconds Time to advance time step: 0.031095844 Call to estdt for level 0 gives dt_lev = 2.439853595e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 24 gives dt =1e+20 dt_growth factor limits the new dt = 0.005858644545 Timestep 24 starts with TIME = 0.07902475981 DT = 0.005858644545 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.005903751e-30 MLMG: Initial residual (resid0) = 8.005903751e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 7.641995188e-40, 9.54544974e-11 MLMG: Timers: Solve = 0.004292349 Iter = 0.004043954 Bottom = 0.000178983 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.005903751e-30 MLMG: Initial residual (resid0) = 7.641995188e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000270617 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.371890809e-19 MLMG: Initial residual (resid0) = 3.371890809e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.976497655e-30, 1.772446972e-11 MLMG: Timers: Solve = 0.005961826 Iter = 0.005780377 Bottom = 0.000241913 Done calling nodal solver Timestep 24 ends with TIME = 0.08488340435 DT = 0.005858644545 Timing summary: Advection :0.006189989 seconds MAC Proj :0.005289213 seconds Nodal Proj :0.006704257 seconds Reactions :0.012535128 seconds Misc :0.001538955 seconds Base State :5.000015335e-08 seconds Time to advance time step: 0.032391396 Call to estdt for level 0 gives dt_lev = 2.326594909e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 25 gives dt =1e+20 dt_growth factor limits the new dt = 0.006151576773 Timestep 25 starts with TIME = 0.08488340435 DT = 0.006151576773 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.528437685e-30 MLMG: Initial residual (resid0) = 8.528437685e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.023638825e-40, 9.408099257e-11 MLMG: Timers: Solve = 0.004072694 Iter = 0.003851438 Bottom = 0.000152039 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.528437685e-30 MLMG: Initial residual (resid0) = 8.023638825e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000208206 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.540485349e-19 MLMG: Initial residual (resid0) = 3.540485349e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.275401983e-30, 1.772469411e-11 MLMG: Timers: Solve = 0.005938332 Iter = 0.005757824 Bottom = 0.000240842 Done calling nodal solver Timestep 25 ends with TIME = 0.09103498113 DT = 0.006151576773 Timing summary: Advection :0.006052575 seconds MAC Proj :0.004954418 seconds Nodal Proj :0.006691926 seconds Reactions :0.011897001 seconds Misc :0.001554474 seconds Base State :5.20001322e-08 seconds Time to advance time step: 0.031287413 Call to estdt for level 0 gives dt_lev = 2.217290439e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 26 gives dt =1e+20 dt_growth factor limits the new dt = 0.006459155611 Timestep 26 starts with TIME = 0.09103498113 DT = 0.006459155611 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.960898042e-30 MLMG: Initial residual (resid0) = 8.960898042e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.424494264e-40, 9.401395065e-11 MLMG: Timers: Solve = 0.00406547 Iter = 0.003869933 Bottom = 0.000165542 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.960898042e-30 MLMG: Initial residual (resid0) = 8.424494264e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000297436 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.717509617e-19 MLMG: Initial residual (resid0) = 3.717509617e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.589087822e-30, 1.772446746e-11 MLMG: Timers: Solve = 0.005980416 Iter = 0.005789039 Bottom = 0.00024648 Done calling nodal solver Timestep 26 ends with TIME = 0.09749413674 DT = 0.006459155611 Timing summary: Advection :0.006234285 seconds MAC Proj :0.005026886 seconds Nodal Proj :0.00674035 seconds Reactions :0.012078975 seconds Misc :0.001538596 seconds Base State :4.999992598e-08 seconds Time to advance time step: 0.031764308 Call to estdt for level 0 gives dt_lev = 2.112523985e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 27 gives dt =1e+20 dt_growth factor limits the new dt = 0.006782113392 Timestep 27 starts with TIME = 0.09749413674 DT = 0.006782113392 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.409848931e-30 MLMG: Initial residual (resid0) = 9.409848931e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.845794647e-40, 9.400570308e-11 MLMG: Timers: Solve = 0.004139042 Iter = 0.003945771 Bottom = 0.000154911 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.409848931e-30 MLMG: Initial residual (resid0) = 8.845794647e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000196383 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.903385097e-19 MLMG: Initial residual (resid0) = 3.903385097e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.918614436e-30, 1.772465248e-11 MLMG: Timers: Solve = 0.006068915 Iter = 0.005889295 Bottom = 0.000240664 Done calling nodal solver Timestep 27 ends with TIME = 0.1042762501 DT = 0.006782113392 Timing summary: Advection :0.006083869 seconds MAC Proj :0.004997741 seconds Nodal Proj :0.00680469 seconds Reactions :0.011755107 seconds Misc :0.001539898 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.031317157 Call to estdt for level 0 gives dt_lev = 2.01240705e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 28 gives dt =1e+20 dt_growth factor limits the new dt = 0.007121219061 Timestep 28 starts with TIME = 0.1042762501 DT = 0.007121219061 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.87985185e-30 MLMG: Initial residual (resid0) = 9.87985185e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 9.288212598e-40, 9.401165867e-11 MLMG: Timers: Solve = 0.004034975 Iter = 0.003839303 Bottom = 0.000155386 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.87985185e-30 MLMG: Initial residual (resid0) = 9.288212598e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000201449 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.098554352e-19 MLMG: Initial residual (resid0) = 4.098554352e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.264463305e-30, 1.772445277e-11 MLMG: Timers: Solve = 0.00586897 Iter = 0.005680527 Bottom = 0.000244045 Done calling nodal solver Timestep 28 ends with TIME = 0.1113974692 DT = 0.007121219061 Timing summary: Advection :0.005938959 seconds MAC Proj :0.004873011 seconds Nodal Proj :0.006683475 seconds Reactions :0.011921941 seconds Misc :0.001537868 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.031091026 Call to estdt for level 0 gives dt_lev = 1.916892684e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 29 gives dt =1e+20 dt_growth factor limits the new dt = 0.007477280014 Timestep 29 starts with TIME = 0.1113974692 DT = 0.007477280014 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.037509187e-29 MLMG: Initial residual (resid0) = 1.037509187e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 9.752953234e-40, 9.400353609e-11 MLMG: Timers: Solve = 0.004050848 Iter = 0.00385131 Bottom = 0.000155839 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.037509187e-29 MLMG: Initial residual (resid0) = 9.752953234e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00020012 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.30348207e-19 MLMG: Initial residual (resid0) = 4.30348207e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.627789989e-30, 1.772469332e-11 MLMG: Timers: Solve = 0.006008206 Iter = 0.005831106 Bottom = 0.000242011 Done calling nodal solver Timestep 29 ends with TIME = 0.1188747492 DT = 0.007477280014 Timing summary: Advection :0.006019293 seconds MAC Proj :0.004911977 seconds Nodal Proj :0.006760757 seconds Reactions :0.011831707 seconds Misc :0.001528617 seconds Base State :5.000015335e-08 seconds Time to advance time step: 0.031191634 Call to estdt for level 0 gives dt_lev = 1.825810886e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 30 gives dt =1e+20 dt_growth factor limits the new dt = 0.007851144015 Timestep 30 starts with TIME = 0.1188747492 DT = 0.007851144015 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.089501496e-29 MLMG: Initial residual (resid0) = 1.089501496e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.024106753e-39, 9.399773718e-11 MLMG: Timers: Solve = 0.004083157 Iter = 0.003884729 Bottom = 0.000154076 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.089501496e-29 MLMG: Initial residual (resid0) = 1.024106753e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000196305 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.518656173e-19 MLMG: Initial residual (resid0) = 4.518656173e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.00907597e-30, 1.772446423e-11 MLMG: Timers: Solve = 0.006059703 Iter = 0.005862199 Bottom = 0.000260794 Done calling nodal solver Timestep 30 ends with TIME = 0.1267258932 DT = 0.007851144015 Timing summary: Advection :0.006023191999 seconds MAC Proj :0.004922018 seconds Nodal Proj :0.006800072 seconds Reactions :0.0118997 seconds Misc :0.001534841 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.031331338 Call to estdt for level 0 gives dt_lev = 1.738995247e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 31 gives dt =1e+20 dt_growth factor limits the new dt = 0.008243701216 Timestep 31 starts with TIME = 0.1267258932 DT = 0.008243701216 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.144079624e-29 MLMG: Initial residual (resid0) = 1.144079624e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.075258351e-39, 9.398457314e-11 MLMG: Timers: Solve = 0.004159052 Iter = 0.003957045 Bottom = 0.000175732 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.144079624e-29 MLMG: Initial residual (resid0) = 1.075258351e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000212805 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.744588982e-19 MLMG: Initial residual (resid0) = 4.744588982e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.409669399e-30, 1.772475852e-11 MLMG: Timers: Solve = 0.006046286 Iter = 0.00584258 Bottom = 0.000248849 Done calling nodal solver Timestep 31 ends with TIME = 0.1349695944 DT = 0.008243701216 Timing summary: Advection :0.00591715 seconds MAC Proj :0.005006492 seconds Nodal Proj :0.006815789 seconds Reactions :0.011891794 seconds Misc :0.001535899 seconds Base State :6.100003702e-08 seconds Time to advance time step: 0.03130481 Call to estdt for level 0 gives dt_lev = 1.656260551e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 32 gives dt =1e+20 dt_growth factor limits the new dt = 0.008655886277 Timestep 32 starts with TIME = 0.1349695944 DT = 0.008655886277 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.201372446e-29 MLMG: Initial residual (resid0) = 1.201372446e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.129010758e-39, 9.397674818e-11 MLMG: Timers: Solve = 0.004199337 Iter = 0.003948659 Bottom = 0.00017492 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.201372446e-29 MLMG: Initial residual (resid0) = 1.129010758e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.0002469 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.981818431e-19 MLMG: Initial residual (resid0) = 4.981818431e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.830148054e-30, 1.772474886e-11 MLMG: Timers: Solve = 0.006226996 Iter = 0.005968964 Bottom = 0.000287691 Done calling nodal solver Timestep 32 ends with TIME = 0.1436254807 DT = 0.008655886277 Timing summary: Advection :0.006252924 seconds MAC Proj :0.005087467 seconds Nodal Proj :0.007079921 seconds Reactions :0.012677436 seconds Misc :0.001683517 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.032941726 Call to estdt for level 0 gives dt_lev = 1.577440861e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 33 gives dt =1e+20 dt_growth factor limits the new dt = 0.00908868059 Timestep 33 starts with TIME = 0.1436254807 DT = 0.00908868059 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.261567528e-29 MLMG: Initial residual (resid0) = 1.261567528e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.185462067e-39, 9.396738906e-11 MLMG: Timers: Solve = 0.00400033 Iter = 0.003803802 Bottom = 0.000156234 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.261567528e-29 MLMG: Initial residual (resid0) = 1.185462067e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000199072 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.230909353e-19 MLMG: Initial residual (resid0) = 5.230909353e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.271474901e-30, 1.772440368e-11 MLMG: Timers: Solve = 0.005924144 Iter = 0.005736949 Bottom = 0.000248014 Done calling nodal solver Timestep 33 ends with TIME = 0.1527141613 DT = 0.00908868059 Timing summary: Advection :0.006061907 seconds MAC Proj :0.004838311 seconds Nodal Proj :0.006668215 seconds Reactions :0.012009502 seconds Misc :0.001550877 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.031283411 Call to estdt for level 0 gives dt_lev = 1.502378414e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 34 gives dt =1e+20 dt_growth factor limits the new dt = 0.00954311462 Timestep 34 starts with TIME = 0.1527141613 DT = 0.00954311462 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.324582667e-29 MLMG: Initial residual (resid0) = 1.324582667e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.244696354e-39, 9.396894474e-11 MLMG: Timers: Solve = 0.004080527 Iter = 0.003873411 Bottom = 0.000162062 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.324582667e-29 MLMG: Initial residual (resid0) = 1.244696354e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000200817 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.49245482e-19 MLMG: Initial residual (resid0) = 5.49245482e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.735238831e-30, 1.772474995e-11 MLMG: Timers: Solve = 0.00607537 Iter = 0.005888589 Bottom = 0.000244909 Done calling nodal solver Timestep 34 ends with TIME = 0.1622572759 DT = 0.00954311462 Timing summary: Advection :0.00605393 seconds MAC Proj :0.004916208 seconds Nodal Proj :0.006808118 seconds Reactions :0.012105226 seconds Misc :0.001548232 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.031596783 Call to estdt for level 0 gives dt_lev = 1.430880358e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 35 gives dt =1e+20 dt_growth factor limits the new dt = 0.01002027035 Timestep 35 starts with TIME = 0.1622572759 DT = 0.01002027035 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.390963587e-29 MLMG: Initial residual (resid0) = 1.390963587e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.306904197e-39, 9.395675121e-11 MLMG: Timers: Solve = 0.004226185 Iter = 0.003968546 Bottom = 0.00017347 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.390963587e-29 MLMG: Initial residual (resid0) = 1.306904197e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000198687 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.681793327e-19 MLMG: Initial residual (resid0) = 5.681793327e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.54956653e-29, 8.00727212e-11 MLMG: Timers: Solve = 0.006055087 Iter = 0.005866076 Bottom = 0.000311016 Done calling nodal solver Timestep 35 ends with TIME = 0.1722775463 DT = 0.01002027035 Timing summary: Advection :0.006177083 seconds MAC Proj :0.005083327 seconds Nodal Proj :0.006839093 seconds Reactions :0.011852225 seconds Misc :0.00155244 seconds Base State :5.400011105e-08 seconds Time to advance time step: 0.031651054 Call to estdt for level 0 gives dt_lev = 2.977695677e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 36 gives dt =1e+20 dt_growth factor limits the new dt = 0.01052128387 Timestep 36 starts with TIME = 0.1722775463 DT = 0.01052128387 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 4.305515288e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.23205761e-30, 5.184182289e-11 MLMG: Timers: Solve = 0.00406352 Iter = 0.003867096 Bottom = 0.000157682 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 2.23205761e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000203485 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.055431439e-19 MLMG: Initial residual (resid0) = 6.055431439e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.073301499e-29, 1.772460822e-11 MLMG: Timers: Solve = 0.006042988 Iter = 0.005816154 Bottom = 0.000243137 Done calling nodal solver Timestep 36 ends with TIME = 0.1827988301 DT = 0.01052128387 Timing summary: Advection :0.005767516 seconds MAC Proj :0.004915491 seconds Nodal Proj :0.00678289 seconds Reactions :0.011932348 seconds Misc :0.001543471 seconds Base State :5.800006875e-08 seconds Time to advance time step: 0.031083771 Call to estdt for level 0 gives dt_lev = 1.290254218e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 37 gives dt =1e+20 dt_growth factor limits the new dt = 0.01104734806 Timestep 37 starts with TIME = 0.1827988301 DT = 0.01104734806 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.53169484e-29 MLMG: Initial residual (resid0) = 1.53169484e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.182368e-39, 7.719344411e-11 MLMG: Timers: Solve = 0.004002074 Iter = 0.003802446 Bottom = 0.000165961 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.53169484e-29 MLMG: Initial residual (resid0) = 1.182368e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000207183 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.264177143e-19 MLMG: Initial residual (resid0) = 6.264177143e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.855307908e-29, 7.75091093e-11 MLMG: Timers: Solve = 0.005936465 Iter = 0.005746858 Bottom = 0.000246919 Done calling nodal solver Timestep 37 ends with TIME = 0.1938461782 DT = 0.01104734806 Timing summary: Advection :0.006003059 seconds MAC Proj :0.004856262 seconds Nodal Proj :0.00668917 seconds Reactions :0.01208259 seconds Misc :0.001540428 seconds Base State :4.900016393e-08 seconds Time to advance time step: 0.031306834 Call to estdt for level 0 gives dt_lev = 2.789559822e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 38 gives dt =1e+20 dt_growth factor limits the new dt = 0.01159971547 Timestep 38 starts with TIME = 0.1938461782 DT = 0.01159971547 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 4.746830605e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.490741235e-30, 5.247166883e-11 MLMG: Timers: Solve = 0.004068405 Iter = 0.003871772 Bottom = 0.000161013 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 2.490741235e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000200337 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.676113162e-19 MLMG: Initial residual (resid0) = 6.676113162e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.183315432e-29, 1.772461615e-11 MLMG: Timers: Solve = 0.005964107 Iter = 0.005791797 Bottom = 0.000249036 Done calling nodal solver Timestep 38 ends with TIME = 0.2054458937 DT = 0.01159971547 Timing summary: Advection :0.005896669 seconds MAC Proj :0.004929836 seconds Nodal Proj :0.006740158 seconds Reactions :0.011849173 seconds Misc :0.001551995 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.031121574 Call to estdt for level 0 gives dt_lev = 1.168429834e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 39 gives dt =1e+20 dt_growth factor limits the new dt = 0.01217970124 Timestep 39 starts with TIME = 0.2054458937 DT = 0.01217970124 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.536277128e-29 MLMG: Initial residual (resid0) = 1.536277128e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.179416865e-39, 7.677110101e-11 MLMG: Timers: Solve = 0.00399975 Iter = 0.003799621 Bottom = 0.000155195 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.536277128e-29 MLMG: Initial residual (resid0) = 1.179416865e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000202381 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.00991882e-19 MLMG: Initial residual (resid0) = 7.00991882e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.242475185e-29, 1.77245303e-11 MLMG: Timers: Solve = 0.005922575 Iter = 0.005735745 Bottom = 0.00024526 Done calling nodal solver Timestep 39 ends with TIME = 0.2176255949 DT = 0.01217970124 Timing summary: Advection :0.005856873 seconds MAC Proj :0.004846919 seconds Nodal Proj :0.006667174 seconds Reactions :0.011936891 seconds Misc :0.001533474 seconds Base State :4.999992598e-08 seconds Time to advance time step: 0.030996688 Call to estdt for level 0 gives dt_lev = 1.116506554e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 40 gives dt =1e+20 dt_growth factor limits the new dt = 0.0127886863 Timestep 40 starts with TIME = 0.2176255949 DT = 0.0127886863 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.750089547e-29 MLMG: Initial residual (resid0) = 1.750089547e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.668229006e-39, 9.532249417e-11 MLMG: Timers: Solve = 0.004038379 Iter = 0.003837579 Bottom = 0.000155891 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.750089547e-29 MLMG: Initial residual (resid0) = 1.668229006e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000206647 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.360414761e-19 MLMG: Initial residual (resid0) = 7.360414761e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.304586426e-29, 1.772436022e-11 MLMG: Timers: Solve = 0.006278306 Iter = 0.006090035 Bottom = 0.000246968 Done calling nodal solver Timestep 40 ends with TIME = 0.2304142812 DT = 0.0127886863 Timing summary: Advection :0.006058479 seconds MAC Proj :0.004906105 seconds Nodal Proj :0.007017371 seconds Reactions :0.012120025 seconds Misc :0.001558529 seconds Base State :5.000015335e-08 seconds Time to advance time step: 0.031818077 Call to estdt for level 0 gives dt_lev = 1.065037272e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 41 gives dt =1e+20 dt_growth factor limits the new dt = 0.01342812062 Timestep 41 starts with TIME = 0.2304142812 DT = 0.01342812062 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.862969069e-29 MLMG: Initial residual (resid0) = 1.862969069e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.751653909e-39, 9.402485193e-11 MLMG: Timers: Solve = 0.00415307 Iter = 0.003942538 Bottom = 0.000159769 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.862969069e-29 MLMG: Initial residual (resid0) = 1.751653909e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000203372 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.728435499e-19 MLMG: Initial residual (resid0) = 7.728435499e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.369817673e-29, 1.772438514e-11 MLMG: Timers: Solve = 0.006218193 Iter = 0.005990601 Bottom = 0.000245243 Done calling nodal solver Timestep 41 ends with TIME = 0.2438424018 DT = 0.01342812062 Timing summary: Advection :0.00605438 seconds MAC Proj :0.004988907 seconds Nodal Proj :0.006990262 seconds Reactions :0.011888599 seconds Misc :0.001552692 seconds Base State :4.900016393e-08 seconds Time to advance time step: 0.031623935 Call to estdt for level 0 gives dt_lev = 1.015215791e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 42 gives dt =1e+20 dt_growth factor limits the new dt = 0.01409952665 Timestep 42 starts with TIME = 0.2438424018 DT = 0.01409952665 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.957338259e-29 MLMG: Initial residual (resid0) = 1.957338259e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.839075315e-39, 9.395797107e-11 MLMG: Timers: Solve = 0.003992097 Iter = 0.003780392 Bottom = 0.00015779 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.957338259e-29 MLMG: Initial residual (resid0) = 1.839075315e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000200236 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.114857274e-19 MLMG: Initial residual (resid0) = 8.114857274e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.43835189e-29, 1.772491914e-11 MLMG: Timers: Solve = 0.005975544 Iter = 0.005750845 Bottom = 0.00024414 Done calling nodal solver Timestep 42 ends with TIME = 0.2579419285 DT = 0.01409952665 Timing summary: Advection :0.00624061 seconds MAC Proj :0.004838355 seconds Nodal Proj :0.006756012 seconds Reactions :0.012001512 seconds Misc :0.001544252 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.031552343 Call to estdt for level 0 gives dt_lev = 9.67369433e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 43 gives dt =1e+20 dt_growth factor limits the new dt = 0.01480450298 Timestep 43 starts with TIME = 0.2579419285 DT = 0.01480450298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.055380727e-29 MLMG: Initial residual (resid0) = 2.055380727e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.931014507e-39, 9.394923682e-11 MLMG: Timers: Solve = 0.004001208 Iter = 0.003798969 Bottom = 0.000154425 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.055380727e-29 MLMG: Initial residual (resid0) = 1.931014507e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000202777 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.520600138e-19 MLMG: Initial residual (resid0) = 8.520600138e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.510227596e-29, 1.772442752e-11 MLMG: Timers: Solve = 0.006158147 Iter = 0.005879276 Bottom = 0.000245091 Done calling nodal solver Timestep 43 ends with TIME = 0.2727464314 DT = 0.01480450298 Timing summary: Advection :0.006068453 seconds MAC Proj :0.004848075 seconds Nodal Proj :0.006914925 seconds Reactions :0.012017969 seconds Misc :0.00155006 seconds Base State :5.100014278e-08 seconds Time to advance time step: 0.031551734 Call to estdt for level 0 gives dt_lev = 9.21627116e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 44 gives dt =1e+20 dt_growth factor limits the new dt = 0.01554472813 Timestep 44 starts with TIME = 0.2727464314 DT = 0.01554472813 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.158317685e-29 MLMG: Initial residual (resid0) = 2.158317685e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.027620023e-39, 9.394446598e-11 MLMG: Timers: Solve = 0.004053139 Iter = 0.003859377 Bottom = 0.000156381 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.158317685e-29 MLMG: Initial residual (resid0) = 2.027620023e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000202206 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.946630145e-19 MLMG: Initial residual (resid0) = 8.946630145e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.585752938e-29, 1.772458359e-11 MLMG: Timers: Solve = 0.006199765 Iter = 0.006010403 Bottom = 0.000254053 Done calling nodal solver Timestep 44 ends with TIME = 0.2882911596 DT = 0.01554472813 Timing summary: Advection :0.00612111 seconds MAC Proj :0.004909101 seconds Nodal Proj :0.006925526 seconds Reactions :0.011996996 seconds Misc :0.001541699 seconds Base State :6.699997357e-08 seconds Time to advance time step: 0.031659049 Call to estdt for level 0 gives dt_lev = 8.779341895e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 45 gives dt =1e+20 dt_growth factor limits the new dt = 0.01632196453 Timestep 45 starts with TIME = 0.2882911596 DT = 0.01632196453 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.266393495e-29 MLMG: Initial residual (resid0) = 2.266393495e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.128720905e-39, 9.392547718e-11 MLMG: Timers: Solve = 0.003992507 Iter = 0.003796882 Bottom = 0.000154389 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.266393495e-29 MLMG: Initial residual (resid0) = 2.128720905e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000206998 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.053842861e-18 MLMG: Initial residual (resid0) = 1.053842861e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 6.6812532e-29, 6.339895109e-11 MLMG: Timers: Solve = 0.006048277 Iter = 0.005816522 Bottom = 0.000249666 Done calling nodal solver Timestep 45 ends with TIME = 0.3046131241 DT = 0.01632196453 Timing summary: Advection :0.006093174 seconds MAC Proj :0.004868058 seconds Nodal Proj :0.00680784 seconds Reactions :0.011905282 seconds Misc :0.001529683 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.031347892 Call to estdt for level 0 gives dt_lev = 2.02744569e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 46 gives dt =1e+20 dt_growth factor limits the new dt = 0.01713806276 Timestep 46 starts with TIME = 0.3046131241 DT = 0.01713806276 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 7.013230718e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.386529476e-30, 4.828772376e-11 MLMG: Timers: Solve = 0.003997509 Iter = 0.003796889 Bottom = 0.000156043 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 3.386529476e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000200163 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 9.863659735e-19 MLMG: Initial residual (resid0) = 9.863659735e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.748311055e-29, 1.772477054e-11 MLMG: Timers: Solve = 0.006014774 Iter = 0.005800531 Bottom = 0.000251231 Done calling nodal solver Timestep 46 ends with TIME = 0.3217511869 DT = 0.01713806276 Timing summary: Advection :0.005671168 seconds MAC Proj :0.004844615 seconds Nodal Proj :0.00675291 seconds Reactions :0.011939319 seconds Misc :0.001544815 seconds Base State :6.999994184e-08 seconds Time to advance time step: 0.030897092 Call to estdt for level 0 gives dt_lev = 7.924349732e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 47 gives dt =1e+20 dt_growth factor limits the new dt = 0.0179949659 Timestep 47 starts with TIME = 0.3217511869 DT = 0.0179949659 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.807852852e-29 MLMG: Initial residual (resid0) = 1.807852852e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.37289975e-39, 7.594090129e-11 MLMG: Timers: Solve = 0.004098204 Iter = 0.003899741 Bottom = 0.000165167 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.807852852e-29 MLMG: Initial residual (resid0) = 1.37289975e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000204579 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.035684272e-18 MLMG: Initial residual (resid0) = 1.035684272e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.835690497e-29, 1.772442188e-11 MLMG: Timers: Solve = 0.005943623 Iter = 0.005758316 Bottom = 0.000246856 Done calling nodal solver Timestep 47 ends with TIME = 0.3397461528 DT = 0.0179949659 Timing summary: Advection :0.00599837 seconds MAC Proj :0.004939921 seconds Nodal Proj :0.006690106 seconds Reactions :0.011910001 seconds Misc :0.001563618 seconds Base State :4.900016393e-08 seconds Time to advance time step: 0.031267438 Call to estdt for level 0 gives dt_lev = 7.566055076e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 48 gives dt =1e+20 dt_growth factor limits the new dt = 0.01889471419 Timestep 48 starts with TIME = 0.3397461528 DT = 0.01889471419 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.590190152e-29 MLMG: Initial residual (resid0) = 2.590190152e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.464371124e-39, 9.514247908e-11 MLMG: Timers: Solve = 0.004121458 Iter = 0.00391576 Bottom = 0.000161895 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.590190152e-29 MLMG: Initial residual (resid0) = 2.464371124e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000200765 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.087468486e-18 MLMG: Initial residual (resid0) = 1.087468486e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.927461059e-29, 1.772429348e-11 MLMG: Timers: Solve = 0.006129572 Iter = 0.005942487 Bottom = 0.000276354 Done calling nodal solver Timestep 48 ends with TIME = 0.358640867 DT = 0.01889471419 Timing summary: Advection :0.006025477 seconds MAC Proj :0.004955367 seconds Nodal Proj :0.006874782 seconds Reactions :0.01186686 seconds Misc :0.001541491 seconds Base State :5.299989425e-08 seconds Time to advance time step: 0.031407545 Call to estdt for level 0 gives dt_lev = 7.214019049e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 49 gives dt =1e+20 dt_growth factor limits the new dt = 0.0198394499 Timestep 49 starts with TIME = 0.358640867 DT = 0.0198394499 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.753963702e-29 MLMG: Initial residual (resid0) = 2.753963702e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.587705007e-39, 9.396293077e-11 MLMG: Timers: Solve = 0.004065875 Iter = 0.003860885 Bottom = 0.000159891 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.753963702e-29 MLMG: Initial residual (resid0) = 2.587682586e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000224486 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.086359695e-18 MLMG: Initial residual (resid0) = 1.086359695e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 4.015978009e-29, 3.69672957e-11 MLMG: Timers: Solve = 0.005969229 Iter = 0.005775382 Bottom = 0.000248033 Done calling nodal solver Timestep 49 ends with TIME = 0.3784803169 DT = 0.0198394499 Timing summary: Advection :0.006045362 seconds MAC Proj :0.004952019 seconds Nodal Proj :0.006738057 seconds Reactions :0.011938695 seconds Misc :0.00153749 seconds Base State :5.000015335e-08 seconds Time to advance time step: 0.031347281 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 50 gives dt =1e+20 dt_growth factor limits the new dt = 0.0208314224 Timestep 50 starts with TIME = 0.3784803169 DT = 0.0208314224 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 8.242756114e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.779842146e-30, 4.585653262e-11 MLMG: Timers: Solve = 0.004320432 Iter = 0.004109352 Bottom = 0.000156065 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 3.779842146e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000206131 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.198934006e-18 MLMG: Initial residual (resid0) = 1.198934006e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 2.12508073e-29, 1.772475149e-11 MLMG: Timers: Solve = 0.00611619 Iter = 0.005928054 Bottom = 0.000247029 Done calling nodal solver Timestep 50 ends with TIME = 0.3993117393 DT = 0.0208314224 Timing summary: Advection :0.005896769 seconds MAC Proj :0.005168711 seconds Nodal Proj :0.006854546 seconds Reactions :0.011823597 seconds Misc :0.001540959 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.031431 Writing plotfile 50 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.01509023 Writing checkpoint 50 Writing checkpoint chk0000050 Total Time: 3.24395831 Unused ParmParse Variables: [TOP]::maestro.v(nvals = 1) :: [1] [TOP]::amr.check_file(nvals = 1) :: [test_stability_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] AMReX (23.08-31-g435281069858) finalized