MPI initialized with 16 MPI processes MPI initialized with thread support level 0 AMReX (23.09-22-gb2052f2d2e5c) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = 5peaks_const_grav.dat model file = 5peaks_const_grav.dat reading initial model 1000 points found in the initial model 10 variables found in the initial model WARNING: variable not found: gravity WARNING: variable not found: abar WARNING: variable not found: zbar WARNING: variable not found: gpot WARNING: variable not found: cno model file mapping, level: 0 dr of MAESTRO base state = 93750000.000000 dr of input file data = 10010010.010010 maximum radius (cell-centered) of input model = 10000000000.000000 WARNING: resolution of base state array is not an integer multiple of the initial model's resolution. make sure this is a desired property as this could lead to aliasing when performing the interpolation. modulus = 3659909.909910 setting r_cutoff to 105 radius at r_cutoff 9890625000 Maximum HSE Error = 0.054171 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile test_stability_pltInitData after InitData inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.026492668 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.000294203 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile test_stability_pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.015285106 Call to firstdt for level 0 gives dt_lev = 0.01907406555 Multiplying dt_lev by init_shrink; dt_lev = 0.001907406555 Minimum firstdt over all levels = 0.001907406555 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 4.945354899e-27 MLMG: Initial residual (resid0) = 4.945354899e-27 MLMG: Final Iter. 3 resid, resid/bnorm = 2.357566962e-30, 0.0004767235133 MLMG: Timers: Solve = 0.002530518 Iter = 0.002298215 Bottom = 9.2281e-05 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 1 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #2 Calling nodal solver MLMG: Initial rhs = 2.306075226e-30 MLMG: Initial residual (resid0) = 2.306075226e-30 MLMG: Final Iter. 5 resid, resid/bnorm = 1.933632021e-37, 8.384947719e-08 MLMG: Timers: Solve = 0.003594591 Iter = 0.003413684 Bottom = 0.00013506 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 2 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #3 Calling nodal solver MLMG: Initial rhs = 9.742172191e-32 MLMG: Initial residual (resid0) = 9.742172191e-32 MLMG: Final Iter. 4 resid, resid/bnorm = 7.521071013e-41, 7.720117101e-10 MLMG: Timers: Solve = 0.003147994 Iter = 0.002849822 Bottom = 0.000121237 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 3 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Writing plotfile test_stability_pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.013696987 Doing initial pressure iteration #1 Timestep 0 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.893547601e-20 MLMG: Initial residual (resid0) = 4.893547601e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 4.517319815e-31, 9.231175792e-12 MLMG: Timers: Solve = 0.004203078 Iter = 0.003919613 Bottom = 0.000159426 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.893547507e-20 MLMG: Initial residual (resid0) = 2.477484298e-27 MLMG: Final Iter. 4 resid, resid/bnorm = 4.813594311e-30, 9.836615062e-11 MLMG: Timers: Solve = 0.001929411 Iter = 0.001651758 Bottom = 7.803e-05 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.755411273e-17 MLMG: Initial residual (resid0) = 5.755411273e-17 MLMG: Final Iter. 9 resid, resid/bnorm = 1.02012041e-27, 1.772454411e-11 MLMG: Timers: Solve = 0.0063974 Iter = 0.006137179 Bottom = 0.000270665 Done calling nodal solver Timestep 0 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.00651014 seconds MAC Proj :0.006934771 seconds Nodal Proj :0.007197215 seconds Reactions :0.012843755 seconds Misc :0.001960761 seconds Base State :4.599996828e-08 seconds Time to advance time step: 0.03914369 Writing plotfile 0 after all initialization inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.015507386 Writing checkpoint 0 after all initialization Writing checkpoint chk0000000 Calling Evolve() Timestep 1 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.257776127e-26 MLMG: Initial residual (resid0) = 1.257776127e-26 MLMG: Final Iter. 10 resid, resid/bnorm = 1.092411925e-37, 8.685265223e-12 MLMG: Timers: Solve = 0.004110014 Iter = 0.003843239 Bottom = 0.000158453 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.257776127e-26 MLMG: Initial residual (resid0) = 1.092411925e-37 MLMG: No iterations needed MLMG: Timers: Solve = 0.000251466 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.097790919e-19 MLMG: Initial residual (resid0) = 1.097790919e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.945791097e-30, 1.772460551e-11 MLMG: Timers: Solve = 0.006185753 Iter = 0.006016463 Bottom = 0.000244033 Done calling nodal solver Timestep 1 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.006019278 seconds MAC Proj :0.005102983 seconds Nodal Proj :0.006927263 seconds Reactions :0.013677468 seconds Misc :0.001724815 seconds Base State :5.400011105e-08 seconds Time to advance time step: 0.039149991 Call to estdt for level 0 gives dt_lev = 7.191081337e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 2 gives dt =1e+20 dt_growth factor limits the new dt = 0.002002776883 Timestep 2 starts with TIME = 0.001907406555 DT = 0.002002776883 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.080398705e-27 MLMG: Initial residual (resid0) = 8.080398705e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 1.160441939e-37, 1.436119654e-11 MLMG: Timers: Solve = 0.004587144 Iter = 0.004376655 Bottom = 0.000155318 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.498306209e-27 MLMG: Initial residual (resid0) = 2.601349809e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 8.688832515e-37, 9.14777048e-11 MLMG: Timers: Solve = 0.004032795 Iter = 0.003821578 Bottom = 0.000157439 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.096671578e-19 MLMG: Initial residual (resid0) = 1.096671578e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.008844235e-29, 9.19914635e-11 MLMG: Timers: Solve = 0.006218094 Iter = 0.005998452 Bottom = 0.000247078 Done calling nodal solver Timestep 2 ends with TIME = 0.003910183437 DT = 0.002002776883 Timing summary: Advection :0.006187071 seconds MAC Proj :0.009443894 seconds Nodal Proj :0.007281002 seconds Reactions :0.012402692 seconds Misc :0.001452542 seconds Base State :6.200002645e-08 seconds Time to advance time step: 0.036933145 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 3 gives dt =1e+20 dt_growth factor limits the new dt = 0.002102915727 Timestep 3 starts with TIME = 0.003910183437 DT = 0.002102915727 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 8.320997544e-21 MLMG: Final Iter. 10 resid, resid/bnorm = 7.676109766e-31, 9.22498742e-11 MLMG: Timers: Solve = 0.00405591 Iter = 0.003839497 Bottom = 0.000153639 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 7.676109766e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000224087 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.21031446e-19 MLMG: Initial residual (resid0) = 1.21031446e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.145209106e-30, 1.772439458e-11 MLMG: Timers: Solve = 0.006381088 Iter = 0.006171229 Bottom = 0.000254857 Done calling nodal solver Timestep 3 ends with TIME = 0.006013099164 DT = 0.002102915727 Timing summary: Advection :0.005828158 seconds MAC Proj :0.00493948 seconds Nodal Proj :0.007209174 seconds Reactions :0.012534153 seconds Misc :0.001819587 seconds Base State :5.09999154e-08 seconds Time to advance time step: 0.032532281 Call to estdt for level 0 gives dt_lev = 6.528630569e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 4 gives dt =1e+20 dt_growth factor limits the new dt = 0.002208061513 Timestep 4 starts with TIME = 0.006013099164 DT = 0.002208061513 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.308039747e-29 MLMG: Initial residual (resid0) = 1.308039747e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.129752045e-39, 8.636985596e-11 MLMG: Timers: Solve = 0.004086646 Iter = 0.003880554 Bottom = 0.000153902 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.308039747e-29 MLMG: Initial residual (resid0) = 1.129752045e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000249554 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.270830183e-19 MLMG: Initial residual (resid0) = 1.270830183e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.252495441e-30, 1.772459822e-11 MLMG: Timers: Solve = 0.006110864 Iter = 0.005933153 Bottom = 0.000240285 Done calling nodal solver Timestep 4 ends with TIME = 0.008221160677 DT = 0.002208061513 Timing summary: Advection :0.006271806 seconds MAC Proj :0.005018982 seconds Nodal Proj :0.006841238 seconds Reactions :0.012155849 seconds Misc :0.001567324 seconds Base State :8.400002116e-08 seconds Time to advance time step: 0.032019499 Call to estdt for level 0 gives dt_lev = 6.226258359e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 5 gives dt =1e+20 dt_growth factor limits the new dt = 0.002318464589 Timestep 5 starts with TIME = 0.008221160677 DT = 0.002318464589 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.295923274e-30 MLMG: Initial residual (resid0) = 3.295923274e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.024366424e-40, 9.176082608e-11 MLMG: Timers: Solve = 0.004824624 Iter = 0.004617182 Bottom = 0.000151409 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.295923274e-30 MLMG: Initial residual (resid0) = 3.024366424e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000211012 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.334371692e-19 MLMG: Initial residual (resid0) = 1.334371692e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.365138268e-30, 1.772473353e-11 MLMG: Timers: Solve = 0.006480171 Iter = 0.006314672 Bottom = 0.000240583 Done calling nodal solver Timestep 5 ends with TIME = 0.01053962527 DT = 0.002318464589 Timing summary: Advection :0.006082942 seconds MAC Proj :0.005673332 seconds Nodal Proj :0.00723052 seconds Reactions :0.01227165 seconds Misc :0.001479577 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.032898013 Call to estdt for level 0 gives dt_lev = 5.915049504e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 6 gives dt =1e+20 dt_growth factor limits the new dt = 0.002434387818 Timestep 6 starts with TIME = 0.01053962527 DT = 0.002434387818 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.377753945e-30 MLMG: Initial residual (resid0) = 3.377753945e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.175503469e-40, 9.401227921e-11 MLMG: Timers: Solve = 0.004086612 Iter = 0.003870804 Bottom = 0.000156623 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.377753945e-30 MLMG: Initial residual (resid0) = 3.175499966e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000218054 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.401090277e-19 MLMG: Initial residual (resid0) = 1.401090277e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.483342219e-30, 1.772435552e-11 MLMG: Timers: Solve = 0.00608227 Iter = 0.005896752 Bottom = 0.000241586 Done calling nodal solver Timestep 6 ends with TIME = 0.01297401308 DT = 0.002434387818 Timing summary: Advection :0.006131017 seconds MAC Proj :0.004952298 seconds Nodal Proj :0.006835295 seconds Reactions :0.012282239 seconds Misc :0.001464709 seconds Base State :4.999992598e-08 seconds Time to advance time step: 0.031822627 Call to estdt for level 0 gives dt_lev = 5.625515433e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 7 gives dt =1e+20 dt_growth factor limits the new dt = 0.002556107209 Timestep 7 starts with TIME = 0.01297401308 DT = 0.002556107209 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.543159178e-30 MLMG: Initial residual (resid0) = 3.543159178e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.334123449e-40, 9.410030095e-11 MLMG: Timers: Solve = 0.004065338 Iter = 0.003848544 Bottom = 0.000153761 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.543159178e-30 MLMG: Initial residual (resid0) = 3.334123449e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000219554 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.471144791e-19 MLMG: Initial residual (resid0) = 1.471144791e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.607516552e-30, 1.772440461e-11 MLMG: Timers: Solve = 0.006038471 Iter = 0.005871443 Bottom = 0.000240168 Done calling nodal solver Timestep 7 ends with TIME = 0.01553012029 DT = 0.002556107209 Timing summary: Advection :0.006088859 seconds MAC Proj :0.004919376 seconds Nodal Proj :0.006785273 seconds Reactions :0.013646093 seconds Misc :0.001460422 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.033059996 Call to estdt for level 0 gives dt_lev = 5.353255202e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 8 gives dt =1e+20 dt_growth factor limits the new dt = 0.002683912569 Timestep 8 starts with TIME = 0.01553012029 DT = 0.002683912569 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.720271341e-30 MLMG: Initial residual (resid0) = 3.720271341e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.500226363e-40, 9.408524384e-11 MLMG: Timers: Solve = 0.004610124 Iter = 0.00438489 Bottom = 0.000156582 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.720271341e-30 MLMG: Initial residual (resid0) = 3.500226363e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000211534 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.54470203e-19 MLMG: Initial residual (resid0) = 1.54470203e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.737914046e-30, 1.772454488e-11 MLMG: Timers: Solve = 0.00656899 Iter = 0.00636337 Bottom = 0.00025832 Done calling nodal solver Timestep 8 ends with TIME = 0.01821403286 DT = 0.002683912569 Timing summary: Advection :0.0061157 seconds MAC Proj :0.005578067 seconds Nodal Proj :0.007318537 seconds Reactions :0.012101651 seconds Misc :0.001459393 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.032742505 Call to estdt for level 0 gives dt_lev = 5.095618567e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 9 gives dt =1e+20 dt_growth factor limits the new dt = 0.002818108198 Timestep 9 starts with TIME = 0.01821403286 DT = 0.002818108198 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.90613533e-30 MLMG: Initial residual (resid0) = 3.90613533e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.675781034e-40, 9.410275692e-11 MLMG: Timers: Solve = 0.004060925 Iter = 0.003839495 Bottom = 0.00015337 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.90613533e-30 MLMG: Initial residual (resid0) = 3.675781034e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000216476 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.621937132e-19 MLMG: Initial residual (resid0) = 1.621937132e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.874835628e-30, 1.772470444e-11 MLMG: Timers: Solve = 0.00607653 Iter = 0.005865088 Bottom = 0.000247927 Done calling nodal solver Timestep 9 ends with TIME = 0.02103214106 DT = 0.002818108198 Timing summary: Advection :0.006247733 seconds MAC Proj :0.004946027 seconds Nodal Proj :0.006835254 seconds Reactions :0.012730789 seconds Misc :0.001445325 seconds Base State :4.80001745e-08 seconds Time to advance time step: 0.032403011 Call to estdt for level 0 gives dt_lev = 4.851290067e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 10 gives dt =1e+20 dt_growth factor limits the new dt = 0.002959013608 Timestep 10 starts with TIME = 0.02103214106 DT = 0.002959013608 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.101240383e-30 MLMG: Initial residual (resid0) = 4.101240383e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.859393172e-40, 9.410307155e-11 MLMG: Timers: Solve = 0.00403579 Iter = 0.003817093 Bottom = 0.000154076 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.101240383e-30 MLMG: Initial residual (resid0) = 3.859393172e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000199762 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.703033988e-19 MLMG: Initial residual (resid0) = 1.703033988e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.174814859e-29, 6.898364135e-11 MLMG: Timers: Solve = 0.006044343 Iter = 0.005862703 Bottom = 0.000243738 Done calling nodal solver Timestep 10 ends with TIME = 0.02399115467 DT = 0.002959013608 Timing summary: Advection :0.00603709 seconds MAC Proj :0.004902398 seconds Nodal Proj :0.006824454 seconds Reactions :0.013556066 seconds Misc :0.001458231 seconds Base State :4.900016393e-08 seconds Time to advance time step: 0.032936971 Call to estdt for level 0 gives dt_lev = 1.153498162e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 11 gives dt =1e+20 dt_growth factor limits the new dt = 0.003106964288 Timestep 11 starts with TIME = 0.02399115467 DT = 0.003106964288 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 1.271430598e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.310137768e-31, 4.963021794e-11 MLMG: Timers: Solve = 0.004025178 Iter = 0.003832139 Bottom = 0.000153286 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 6.310137768e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000217705 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.788185688e-19 MLMG: Initial residual (resid0) = 1.788185688e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.169478835e-30, 1.772455096e-11 MLMG: Timers: Solve = 0.006442605 Iter = 0.006263341 Bottom = 0.000243456 Done calling nodal solver Timestep 11 ends with TIME = 0.02709811896 DT = 0.003106964288 Timing summary: Advection :0.006405524 seconds MAC Proj :0.004906631 seconds Nodal Proj :0.007175795 seconds Reactions :0.012161063 seconds Misc :0.001461425 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.03226082 Call to estdt for level 0 gives dt_lev = 4.376664086e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 12 gives dt =1e+20 dt_growth factor limits the new dt = 0.003262312503 Timestep 12 starts with TIME = 0.02709811896 DT = 0.003262312503 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.931483508e-30 MLMG: Initial residual (resid0) = 2.931483508e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.211723667e-40, 7.544724916e-11 MLMG: Timers: Solve = 0.004051069 Iter = 0.003847012 Bottom = 0.000154369 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.931483508e-30 MLMG: Initial residual (resid0) = 2.211723667e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00020134 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.877594972e-19 MLMG: Initial residual (resid0) = 1.877594972e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.328006944e-30, 1.772483945e-11 MLMG: Timers: Solve = 0.006608307 Iter = 0.006418226 Bottom = 0.000243467 Done calling nodal solver Timestep 12 ends with TIME = 0.03036043146 DT = 0.003262312503 Timing summary: Advection :0.006673075 seconds MAC Proj :0.004996958 seconds Nodal Proj :0.0074347 seconds Reactions :0.012243159 seconds Misc :0.00148084 seconds Base State :4.900016393e-08 seconds Time to advance time step: 0.033004279 Call to estdt for level 0 gives dt_lev = 4.177466111e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 13 gives dt =1e+20 dt_growth factor limits the new dt = 0.003425428128 Timestep 13 starts with TIME = 0.03036043146 DT = 0.003425428128 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.688771914e-30 MLMG: Initial residual (resid0) = 4.688771914e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.468299394e-40, 9.529786213e-11 MLMG: Timers: Solve = 0.00615328 Iter = 0.005582444 Bottom = 0.000151742 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.688771914e-30 MLMG: Initial residual (resid0) = 4.468299394e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000343393 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.971474721e-19 MLMG: Initial residual (resid0) = 1.971474721e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.494383217e-30, 1.772471734e-11 MLMG: Timers: Solve = 0.006325605 Iter = 0.006131497 Bottom = 0.000246694 Done calling nodal solver Timestep 13 ends with TIME = 0.03378585959 DT = 0.003425428128 Timing summary: Advection :0.008807771 seconds MAC Proj :0.007261501 seconds Nodal Proj :0.007146601 seconds Reactions :0.014689729 seconds Misc :0.001681975 seconds Base State :4.80001745e-08 seconds Time to advance time step: 0.040616449 Call to estdt for level 0 gives dt_lev = 3.982280624e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 14 gives dt =1e+20 dt_growth factor limits the new dt = 0.003596699534 Timestep 14 starts with TIME = 0.03378585959 DT = 0.003596699534 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.983088965e-30 MLMG: Initial residual (resid0) = 4.983088965e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.691428148e-40, 9.414698756e-11 MLMG: Timers: Solve = 0.004061751 Iter = 0.003846852 Bottom = 0.000154783 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.983088965e-30 MLMG: Initial residual (resid0) = 4.691428148e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000204135 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.221658729e-19 MLMG: Initial residual (resid0) = 2.221658729e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.863249975e-30, 3.989474107e-11 MLMG: Timers: Solve = 0.006051036 Iter = 0.005884898 Bottom = 0.000241037 Done calling nodal solver Timestep 14 ends with TIME = 0.03738255912 DT = 0.003596699534 Timing summary: Advection :0.006069075 seconds MAC Proj :0.004920228 seconds Nodal Proj :0.0068212 seconds Reactions :0.012722304 seconds Misc :0.00172513 seconds Base State :5.20001322e-08 seconds Time to advance time step: 0.032413587 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 15 gives dt =1e+20 dt_growth factor limits the new dt = 0.003776534511 Timestep 15 starts with TIME = 0.03738255912 DT = 0.003776534511 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 1.44706648e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 8.547886059e-31, 5.907044478e-11 MLMG: Timers: Solve = 0.004046165 Iter = 0.00383837 Bottom = 0.000158998 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 8.547886059e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000201074 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.279163939e-19 MLMG: Initial residual (resid0) = 2.279163939e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.500906095e-29, 6.585336268e-11 MLMG: Timers: Solve = 0.006076836 Iter = 0.005875585 Bottom = 0.000241938 Done calling nodal solver Timestep 15 ends with TIME = 0.04115909363 DT = 0.003776534511 Timing summary: Advection :0.005838038 seconds MAC Proj :0.004883304 seconds Nodal Proj :0.006822912 seconds Reactions :0.012116743 seconds Misc :0.001490914 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.031326222 Call to estdt for level 0 gives dt_lev = 9.044193233e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 16 gives dt =1e+20 dt_growth factor limits the new dt = 0.003965361236 Timestep 16 starts with TIME = 0.04115909363 DT = 0.003965361236 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 1.62270343e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.18702781e-31, 3.812790245e-11 MLMG: Timers: Solve = 0.004104019 Iter = 0.003903434 Bottom = 0.000153141 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 6.18702781e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000217019 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.282228424e-19 MLMG: Initial residual (resid0) = 2.282228424e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.045151033e-30, 1.772456688e-11 MLMG: Timers: Solve = 0.006107299 Iter = 0.005904106 Bottom = 0.000243633 Done calling nodal solver Timestep 16 ends with TIME = 0.04512445487 DT = 0.003965361236 Timing summary: Advection :0.00564303 seconds MAC Proj :0.004968954 seconds Nodal Proj :0.006872922 seconds Reactions :0.012262008 seconds Misc :0.001470843 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.031373472 Call to estdt for level 0 gives dt_lev = 3.436593485e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 17 gives dt =1e+20 dt_growth factor limits the new dt = 0.004163629298 Timestep 17 starts with TIME = 0.04512445487 DT = 0.004163629298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.754694364e-30 MLMG: Initial residual (resid0) = 3.754694364e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.825939058e-40, 7.526415691e-11 MLMG: Timers: Solve = 0.004042728 Iter = 0.003841835 Bottom = 0.000152874 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.754694364e-30 MLMG: Initial residual (resid0) = 2.825939058e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000203868 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.396339845e-19 MLMG: Initial residual (resid0) = 2.396339845e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.247301455e-30, 1.772411982e-11 MLMG: Timers: Solve = 0.006056611 Iter = 0.005889542 Bottom = 0.000246235 Done calling nodal solver Timestep 17 ends with TIME = 0.04928808417 DT = 0.004163629298 Timing summary: Advection :0.006037746 seconds MAC Proj :0.004928949 seconds Nodal Proj :0.006812132 seconds Reactions :0.012117221 seconds Misc :0.001442026 seconds Base State :5.000015335e-08 seconds Time to advance time step: 0.0315103 Call to estdt for level 0 gives dt_lev = 3.276898941e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 18 gives dt =1e+20 dt_growth factor limits the new dt = 0.004371810763 Timestep 18 starts with TIME = 0.04928808417 DT = 0.004371810763 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.989009514e-30 MLMG: Initial residual (resid0) = 5.989009514e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.702479003e-40, 9.521572791e-11 MLMG: Timers: Solve = 0.004086821 Iter = 0.003877664 Bottom = 0.000152459 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.989009514e-30 MLMG: Initial residual (resid0) = 5.702479003e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000205298 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.516156837e-19 MLMG: Initial residual (resid0) = 2.516156837e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.459755602e-30, 1.772447383e-11 MLMG: Timers: Solve = 0.006210471 Iter = 0.006004702 Bottom = 0.000242629 Done calling nodal solver Timestep 18 ends with TIME = 0.05365989493 DT = 0.004371810763 Timing summary: Advection :0.006190794 seconds MAC Proj :0.004917672 seconds Nodal Proj :0.006977059 seconds Reactions :0.012156358 seconds Misc :0.001466955 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.031869588 Call to estdt for level 0 gives dt_lev = 3.122265826e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 19 gives dt =1e+20 dt_growth factor limits the new dt = 0.004590401301 Timestep 19 starts with TIME = 0.05365989493 DT = 0.004590401301 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.361324287e-30 MLMG: Initial residual (resid0) = 6.361324287e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.987979552e-40, 9.413102181e-11 MLMG: Timers: Solve = 0.004012575 Iter = 0.003816878 Bottom = 0.000154399 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.361324287e-30 MLMG: Initial residual (resid0) = 5.987979552e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000202249 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.641964679e-19 MLMG: Initial residual (resid0) = 2.641964679e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.682802363e-30, 1.772469708e-11 MLMG: Timers: Solve = 0.006110534 Iter = 0.005936422 Bottom = 0.00024069 Done calling nodal solver Timestep 19 ends with TIME = 0.05825029623 DT = 0.004590401301 Timing summary: Advection :0.006165327 seconds MAC Proj :0.00484917 seconds Nodal Proj :0.006853496 seconds Reactions :0.01217048 seconds Misc :0.001446445 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.031658901 Call to estdt for level 0 gives dt_lev = 2.974206455e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 20 gives dt =1e+20 dt_growth factor limits the new dt = 0.004819921366 Timestep 20 starts with TIME = 0.05825029623 DT = 0.004819921366 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.683696559e-30 MLMG: Initial residual (resid0) = 6.683696559e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.287226839e-40, 9.406810713e-11 MLMG: Timers: Solve = 0.004057541 Iter = 0.003856203 Bottom = 0.000154386 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.683696559e-30 MLMG: Initial residual (resid0) = 6.287226839e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000196507 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.774062913e-19 MLMG: Initial residual (resid0) = 2.774062913e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.916899148e-30, 1.772454087e-11 MLMG: Timers: Solve = 0.00632317 Iter = 0.006150688 Bottom = 0.000245568 Done calling nodal solver Timestep 20 ends with TIME = 0.0630702176 DT = 0.004819921366 Timing summary: Advection :0.006145147 seconds MAC Proj :0.004897202 seconds Nodal Proj :0.007055264 seconds Reactions :0.012221064 seconds Misc :0.00144957 seconds Base State :2.220001534e-07 seconds Time to advance time step: 0.031940514 Call to estdt for level 0 gives dt_lev = 2.83287101e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 21 gives dt =1e+20 dt_growth factor limits the new dt = 0.005060917435 Timestep 21 starts with TIME = 0.0630702176 DT = 0.005060917435 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.019131084e-30 MLMG: Initial residual (resid0) = 7.019131084e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.601334897e-40, 9.40477506e-11 MLMG: Timers: Solve = 0.004043071 Iter = 0.003844093 Bottom = 0.000153564 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.019131084e-30 MLMG: Initial residual (resid0) = 6.601334897e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000236954 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.869691725e-19 MLMG: Initial residual (resid0) = 2.869691725e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.297839054e-29, 8.007267937e-11 MLMG: Timers: Solve = 0.006066744 Iter = 0.005888878 Bottom = 0.000246439 Done calling nodal solver Timestep 21 ends with TIME = 0.06813113503 DT = 0.005060917435 Timing summary: Advection :0.006019982 seconds MAC Proj :0.004952306 seconds Nodal Proj :0.006819605 seconds Reactions :0.012401886 seconds Misc :0.001500839 seconds Base State :4.499997885e-08 seconds Time to advance time step: 0.031856435 Call to estdt for level 0 gives dt_lev = 5.895631152e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 22 gives dt =1e+20 dt_growth factor limits the new dt = 0.005313963306 Timestep 22 starts with TIME = 0.06813113503 DT = 0.005313963306 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 2.174577793e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 1.127461332e-30, 5.184736713e-11 MLMG: Timers: Solve = 0.004102447 Iter = 0.003908701 Bottom = 0.000153958 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 1.127461332e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000236709 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.058404362e-19 MLMG: Initial residual (resid0) = 3.058404362e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.420866866e-30, 1.772449364e-11 MLMG: Timers: Solve = 0.006088924 Iter = 0.005880507 Bottom = 0.000255818 Done calling nodal solver Timestep 22 ends with TIME = 0.07344509834 DT = 0.005313963306 Timing summary: Advection :0.00580853 seconds MAC Proj :0.005020646 seconds Nodal Proj :0.006830071 seconds Reactions :0.012221364 seconds Misc :0.001449182 seconds Base State :4.999992598e-08 seconds Time to advance time step: 0.031484183 Call to estdt for level 0 gives dt_lev = 2.554672307e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 23 gives dt =1e+20 dt_growth factor limits the new dt = 0.005579661472 Timestep 23 starts with TIME = 0.07344509834 DT = 0.005579661472 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.733416233e-30 MLMG: Initial residual (resid0) = 7.733416233e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.972214945e-40, 7.722608954e-11 MLMG: Timers: Solve = 0.004076619 Iter = 0.003869989 Bottom = 0.000155588 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.733416233e-30 MLMG: Initial residual (resid0) = 5.972214945e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000198656 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.21132458e-19 MLMG: Initial residual (resid0) = 3.21132458e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.691941506e-30, 1.77245911e-11 MLMG: Timers: Solve = 0.006078708 Iter = 0.005914243 Bottom = 0.000242477 Done calling nodal solver Timestep 23 ends with TIME = 0.07902475981 DT = 0.005579661472 Timing summary: Advection :0.005877891 seconds MAC Proj :0.004967395 seconds Nodal Proj :0.006831461 seconds Reactions :0.012135078 seconds Misc :0.001470148 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.031442869 Call to estdt for level 0 gives dt_lev = 2.439853595e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 24 gives dt =1e+20 dt_growth factor limits the new dt = 0.005858644545 Timestep 24 starts with TIME = 0.07902475981 DT = 0.005858644545 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.005903751e-30 MLMG: Initial residual (resid0) = 8.005903751e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 7.641995188e-40, 9.54544974e-11 MLMG: Timers: Solve = 0.004071074 Iter = 0.003878873 Bottom = 0.000152427 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.005903751e-30 MLMG: Initial residual (resid0) = 7.641995188e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00021038 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.371890809e-19 MLMG: Initial residual (resid0) = 3.371890809e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.976497655e-30, 1.772446972e-11 MLMG: Timers: Solve = 0.006132476 Iter = 0.005960936 Bottom = 0.000245408 Done calling nodal solver Timestep 24 ends with TIME = 0.08488340435 DT = 0.005858644545 Timing summary: Advection :0.006003932 seconds MAC Proj :0.004937375 seconds Nodal Proj :0.006847148 seconds Reactions :0.012041451 seconds Misc :0.001457794 seconds Base State :4.80001745e-08 seconds Time to advance time step: 0.031448411 Call to estdt for level 0 gives dt_lev = 2.326594909e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 25 gives dt =1e+20 dt_growth factor limits the new dt = 0.006151576773 Timestep 25 starts with TIME = 0.08488340435 DT = 0.006151576773 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.528437685e-30 MLMG: Initial residual (resid0) = 8.528437685e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.023638825e-40, 9.408099257e-11 MLMG: Timers: Solve = 0.00401182 Iter = 0.00381797 Bottom = 0.000152974 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.528437685e-30 MLMG: Initial residual (resid0) = 8.023638825e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000201611 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.540485349e-19 MLMG: Initial residual (resid0) = 3.540485349e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.275401983e-30, 1.772469411e-11 MLMG: Timers: Solve = 0.006103535 Iter = 0.005929907 Bottom = 0.00024418 Done calling nodal solver Timestep 25 ends with TIME = 0.09103498113 DT = 0.006151576773 Timing summary: Advection :0.006035851 seconds MAC Proj :0.004867837 seconds Nodal Proj :0.00682882 seconds Reactions :0.012074566 seconds Misc :0.00145058 seconds Base State :4.900016393e-08 seconds Time to advance time step: 0.031418271 Call to estdt for level 0 gives dt_lev = 2.217290439e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 26 gives dt =1e+20 dt_growth factor limits the new dt = 0.006459155611 Timestep 26 starts with TIME = 0.09103498113 DT = 0.006459155611 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.960898042e-30 MLMG: Initial residual (resid0) = 8.960898042e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.424494264e-40, 9.401395065e-11 MLMG: Timers: Solve = 0.004055052 Iter = 0.003863474 Bottom = 0.000151444 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.960898042e-30 MLMG: Initial residual (resid0) = 8.424494264e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000211273 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.717509617e-19 MLMG: Initial residual (resid0) = 3.717509617e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.589087822e-30, 1.772446746e-11 MLMG: Timers: Solve = 0.006009557 Iter = 0.005835676 Bottom = 0.000246358 Done calling nodal solver Timestep 26 ends with TIME = 0.09749413674 DT = 0.006459155611 Timing summary: Advection :0.006026339 seconds MAC Proj :0.004898845 seconds Nodal Proj :0.006739797 seconds Reactions :0.01207134 seconds Misc :0.001474083 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.031373569 Call to estdt for level 0 gives dt_lev = 2.112523985e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 27 gives dt =1e+20 dt_growth factor limits the new dt = 0.006782113392 Timestep 27 starts with TIME = 0.09749413674 DT = 0.006782113392 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.409848931e-30 MLMG: Initial residual (resid0) = 9.409848931e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.845794647e-40, 9.400570308e-11 MLMG: Timers: Solve = 0.004033246 Iter = 0.003846888 Bottom = 0.000153415 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.409848931e-30 MLMG: Initial residual (resid0) = 8.845794647e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000194223 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.903385097e-19 MLMG: Initial residual (resid0) = 3.903385097e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.918614436e-30, 1.772465248e-11 MLMG: Timers: Solve = 0.006058566 Iter = 0.005885481 Bottom = 0.000241299 Done calling nodal solver Timestep 27 ends with TIME = 0.1042762501 DT = 0.006782113392 Timing summary: Advection :0.006145981 seconds MAC Proj :0.004862994 seconds Nodal Proj :0.006825209 seconds Reactions :0.012163365 seconds Misc :0.001471828 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.031623373 Call to estdt for level 0 gives dt_lev = 2.01240705e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 28 gives dt =1e+20 dt_growth factor limits the new dt = 0.007121219061 Timestep 28 starts with TIME = 0.1042762501 DT = 0.007121219061 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.87985185e-30 MLMG: Initial residual (resid0) = 9.87985185e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 9.288212598e-40, 9.401165867e-11 MLMG: Timers: Solve = 0.004036733 Iter = 0.003839966 Bottom = 0.000151791 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.87985185e-30 MLMG: Initial residual (resid0) = 9.288212598e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000194336 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.098554352e-19 MLMG: Initial residual (resid0) = 4.098554352e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.264463305e-30, 1.772445277e-11 MLMG: Timers: Solve = 0.006161517 Iter = 0.005986695 Bottom = 0.000241412 Done calling nodal solver Timestep 28 ends with TIME = 0.1113974692 DT = 0.007121219061 Timing summary: Advection :0.006080383 seconds MAC Proj :0.004888736 seconds Nodal Proj :0.006908555 seconds Reactions :0.012350605 seconds Misc :0.001454907 seconds Base State :4.80001745e-08 seconds Time to advance time step: 0.031846027 Call to estdt for level 0 gives dt_lev = 1.916892684e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 29 gives dt =1e+20 dt_growth factor limits the new dt = 0.007477280014 Timestep 29 starts with TIME = 0.1113974692 DT = 0.007477280014 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.037509187e-29 MLMG: Initial residual (resid0) = 1.037509187e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 9.752953234e-40, 9.400353609e-11 MLMG: Timers: Solve = 0.004042044 Iter = 0.003848177 Bottom = 0.000153264 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.037509187e-29 MLMG: Initial residual (resid0) = 9.752953234e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00019653 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.30348207e-19 MLMG: Initial residual (resid0) = 4.30348207e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.627789989e-30, 1.772469332e-11 MLMG: Timers: Solve = 0.006105899 Iter = 0.005928793 Bottom = 0.000247744 Done calling nodal solver Timestep 29 ends with TIME = 0.1188747492 DT = 0.007477280014 Timing summary: Advection :0.006122888 seconds MAC Proj :0.004886252 seconds Nodal Proj :0.006873215 seconds Reactions :0.012244979 seconds Misc :0.001437265 seconds Base State :5.20001322e-08 seconds Time to advance time step: 0.031721182 Call to estdt for level 0 gives dt_lev = 1.825810886e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 30 gives dt =1e+20 dt_growth factor limits the new dt = 0.007851144015 Timestep 30 starts with TIME = 0.1188747492 DT = 0.007851144015 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.089501496e-29 MLMG: Initial residual (resid0) = 1.089501496e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.024106753e-39, 9.399773718e-11 MLMG: Timers: Solve = 0.004065335 Iter = 0.003876835 Bottom = 0.000151499 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.089501496e-29 MLMG: Initial residual (resid0) = 1.024106753e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000195197 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.518656173e-19 MLMG: Initial residual (resid0) = 4.518656173e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.00907597e-30, 1.772446423e-11 MLMG: Timers: Solve = 0.005986343 Iter = 0.005816807 Bottom = 0.000240057 Done calling nodal solver Timestep 30 ends with TIME = 0.1267258932 DT = 0.007851144015 Timing summary: Advection :0.006094819 seconds MAC Proj :0.004915474 seconds Nodal Proj :0.006703952 seconds Reactions :0.012256353 seconds Misc :0.001468284 seconds Base State :5.100014278e-08 seconds Time to advance time step: 0.031594595 Call to estdt for level 0 gives dt_lev = 1.738995247e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 31 gives dt =1e+20 dt_growth factor limits the new dt = 0.008243701216 Timestep 31 starts with TIME = 0.1267258932 DT = 0.008243701216 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.144079624e-29 MLMG: Initial residual (resid0) = 1.144079624e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.075258351e-39, 9.398457314e-11 MLMG: Timers: Solve = 0.004053419 Iter = 0.003843618 Bottom = 0.000152802 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.144079624e-29 MLMG: Initial residual (resid0) = 1.075258351e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000195827 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.744588982e-19 MLMG: Initial residual (resid0) = 4.744588982e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.409669399e-30, 1.772475852e-11 MLMG: Timers: Solve = 0.006047386 Iter = 0.005879034 Bottom = 0.000248162 Done calling nodal solver Timestep 31 ends with TIME = 0.1349695944 DT = 0.008243701216 Timing summary: Advection :0.006030206 seconds MAC Proj :0.004891115 seconds Nodal Proj :0.006819511 seconds Reactions :0.012304144 seconds Misc :0.001455155 seconds Base State :4.80001745e-08 seconds Time to advance time step: 0.031659413 Call to estdt for level 0 gives dt_lev = 1.656260551e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 32 gives dt =1e+20 dt_growth factor limits the new dt = 0.008655886277 Timestep 32 starts with TIME = 0.1349695944 DT = 0.008655886277 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.201372446e-29 MLMG: Initial residual (resid0) = 1.201372446e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.129010758e-39, 9.397674818e-11 MLMG: Timers: Solve = 0.004022064 Iter = 0.00383158 Bottom = 0.000151387 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.201372446e-29 MLMG: Initial residual (resid0) = 1.129010758e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000199588 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.981818431e-19 MLMG: Initial residual (resid0) = 4.981818431e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.830148054e-30, 1.772474886e-11 MLMG: Timers: Solve = 0.00624849 Iter = 0.006041243 Bottom = 0.000259152 Done calling nodal solver Timestep 32 ends with TIME = 0.1436254807 DT = 0.008655886277 Timing summary: Advection :0.005955194 seconds MAC Proj :0.00485815 seconds Nodal Proj :0.007009575 seconds Reactions :0.01220209 seconds Misc :0.001467852 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.031659892 Call to estdt for level 0 gives dt_lev = 1.577440861e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 33 gives dt =1e+20 dt_growth factor limits the new dt = 0.00908868059 Timestep 33 starts with TIME = 0.1436254807 DT = 0.00908868059 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.261567528e-29 MLMG: Initial residual (resid0) = 1.261567528e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.185462067e-39, 9.396738906e-11 MLMG: Timers: Solve = 0.004027954 Iter = 0.003831868 Bottom = 0.000154818 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.261567528e-29 MLMG: Initial residual (resid0) = 1.185462067e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000196712 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.230909353e-19 MLMG: Initial residual (resid0) = 5.230909353e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.271474901e-30, 1.772440368e-11 MLMG: Timers: Solve = 0.006027738 Iter = 0.005856053 Bottom = 0.000245835 Done calling nodal solver Timestep 33 ends with TIME = 0.1527141613 DT = 0.00908868059 Timing summary: Advection :0.006075894 seconds MAC Proj :0.004855892 seconds Nodal Proj :0.006756533 seconds Reactions :0.012020489 seconds Misc :0.001456639 seconds Base State :4.900016393e-08 seconds Time to advance time step: 0.0313231 Call to estdt for level 0 gives dt_lev = 1.502378414e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 34 gives dt =1e+20 dt_growth factor limits the new dt = 0.00954311462 Timestep 34 starts with TIME = 0.1527141613 DT = 0.00954311462 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.324582667e-29 MLMG: Initial residual (resid0) = 1.324582667e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.244696354e-39, 9.396894474e-11 MLMG: Timers: Solve = 0.004019592 Iter = 0.003821243 Bottom = 0.000152513 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.324582667e-29 MLMG: Initial residual (resid0) = 1.244696354e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000193457 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.49245482e-19 MLMG: Initial residual (resid0) = 5.49245482e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.735238831e-30, 1.772474995e-11 MLMG: Timers: Solve = 0.006194472 Iter = 0.006025397 Bottom = 0.000241654 Done calling nodal solver Timestep 34 ends with TIME = 0.1622572759 DT = 0.00954311462 Timing summary: Advection :0.006002787 seconds MAC Proj :0.00488039 seconds Nodal Proj :0.006991378 seconds Reactions :0.01225521 seconds Misc :0.001455364 seconds Base State :4.900016393e-08 seconds Time to advance time step: 0.031751183 Call to estdt for level 0 gives dt_lev = 1.430880358e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 35 gives dt =1e+20 dt_growth factor limits the new dt = 0.01002027035 Timestep 35 starts with TIME = 0.1622572759 DT = 0.01002027035 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.390963587e-29 MLMG: Initial residual (resid0) = 1.390963587e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.306904197e-39, 9.395675121e-11 MLMG: Timers: Solve = 0.004076022 Iter = 0.003887449 Bottom = 0.000153113 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.390963587e-29 MLMG: Initial residual (resid0) = 1.306904197e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000194307 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.681793327e-19 MLMG: Initial residual (resid0) = 5.681793327e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.54956653e-29, 8.00727212e-11 MLMG: Timers: Solve = 0.00603276 Iter = 0.005861036 Bottom = 0.000247118 Done calling nodal solver Timestep 35 ends with TIME = 0.1722775463 DT = 0.01002027035 Timing summary: Advection :0.005971171 seconds MAC Proj :0.004932351 seconds Nodal Proj :0.00675703 seconds Reactions :0.012232521 seconds Misc :0.001457055 seconds Base State :5.100014278e-08 seconds Time to advance time step: 0.031517572 Call to estdt for level 0 gives dt_lev = 2.977695677e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 36 gives dt =1e+20 dt_growth factor limits the new dt = 0.01052128387 Timestep 36 starts with TIME = 0.1722775463 DT = 0.01052128387 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 4.305515288e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.23205761e-30, 5.184182289e-11 MLMG: Timers: Solve = 0.004110068 Iter = 0.003908375 Bottom = 0.000153429 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 2.23205761e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000195009 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.055431439e-19 MLMG: Initial residual (resid0) = 6.055431439e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.073301499e-29, 1.772460822e-11 MLMG: Timers: Solve = 0.006159567 Iter = 0.005965765 Bottom = 0.000242074 Done calling nodal solver Timestep 36 ends with TIME = 0.1827988301 DT = 0.01052128387 Timing summary: Advection :0.005961598 seconds MAC Proj :0.00494656 seconds Nodal Proj :0.007280372 seconds Reactions :0.01366237 seconds Misc :0.002022567 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.034047157 Call to estdt for level 0 gives dt_lev = 1.290254218e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 37 gives dt =1e+20 dt_growth factor limits the new dt = 0.01104734806 Timestep 37 starts with TIME = 0.1827988301 DT = 0.01104734806 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.53169484e-29 MLMG: Initial residual (resid0) = 1.53169484e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.182368e-39, 7.719344411e-11 MLMG: Timers: Solve = 0.004013017 Iter = 0.003815634 Bottom = 0.000153585 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.53169484e-29 MLMG: Initial residual (resid0) = 1.182368e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000198661 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.264177143e-19 MLMG: Initial residual (resid0) = 6.264177143e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.855307908e-29, 7.75091093e-11 MLMG: Timers: Solve = 0.0064552 Iter = 0.006285795 Bottom = 0.000247231 Done calling nodal solver Timestep 37 ends with TIME = 0.1938461782 DT = 0.01104734806 Timing summary: Advection :0.006133763 seconds MAC Proj :0.004872197 seconds Nodal Proj :0.007208409 seconds Reactions :0.013596235 seconds Misc :0.002072419 seconds Base State :4.999992598e-08 seconds Time to advance time step: 0.03403079 Call to estdt for level 0 gives dt_lev = 2.789559822e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 38 gives dt =1e+20 dt_growth factor limits the new dt = 0.01159971547 Timestep 38 starts with TIME = 0.1938461782 DT = 0.01159971547 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 4.746830605e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.490741235e-30, 5.247166883e-11 MLMG: Timers: Solve = 0.00403773 Iter = 0.003840698 Bottom = 0.000155838 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 2.490741235e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000205682 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.676113162e-19 MLMG: Initial residual (resid0) = 6.676113162e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.183315432e-29, 1.772461615e-11 MLMG: Timers: Solve = 0.006128836 Iter = 0.005922615 Bottom = 0.000240855 Done calling nodal solver Timestep 38 ends with TIME = 0.2054458937 DT = 0.01159971547 Timing summary: Advection :0.005777817 seconds MAC Proj :0.004889146 seconds Nodal Proj :0.00686857 seconds Reactions :0.013472781 seconds Misc :0.001522182 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.032680322 Call to estdt for level 0 gives dt_lev = 1.168429834e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 39 gives dt =1e+20 dt_growth factor limits the new dt = 0.01217970124 Timestep 39 starts with TIME = 0.2054458937 DT = 0.01217970124 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.536277128e-29 MLMG: Initial residual (resid0) = 1.536277128e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.179416865e-39, 7.677110101e-11 MLMG: Timers: Solve = 0.004100281 Iter = 0.00385264 Bottom = 0.000152552 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.536277128e-29 MLMG: Initial residual (resid0) = 1.179416865e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000197312 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.00991882e-19 MLMG: Initial residual (resid0) = 7.00991882e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.242475185e-29, 1.77245303e-11 MLMG: Timers: Solve = 0.006078228 Iter = 0.005904031 Bottom = 0.000245522 Done calling nodal solver Timestep 39 ends with TIME = 0.2176255949 DT = 0.01217970124 Timing summary: Advection :0.006533762 seconds MAC Proj :0.004992351 seconds Nodal Proj :0.006831699 seconds Reactions :0.014625969 seconds Misc :0.001499954 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.034645423 Call to estdt for level 0 gives dt_lev = 1.116506554e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 40 gives dt =1e+20 dt_growth factor limits the new dt = 0.0127886863 Timestep 40 starts with TIME = 0.2176255949 DT = 0.0127886863 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.750089547e-29 MLMG: Initial residual (resid0) = 1.750089547e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.668229006e-39, 9.532249417e-11 MLMG: Timers: Solve = 0.004155946 Iter = 0.003960002 Bottom = 0.000154716 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.750089547e-29 MLMG: Initial residual (resid0) = 1.668229006e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000197484 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.360414761e-19 MLMG: Initial residual (resid0) = 7.360414761e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.304586426e-29, 1.772436022e-11 MLMG: Timers: Solve = 0.006249185 Iter = 0.006078491 Bottom = 0.000248983 Done calling nodal solver Timestep 40 ends with TIME = 0.2304142812 DT = 0.0127886863 Timing summary: Advection :0.006685583 seconds MAC Proj :0.00516236 seconds Nodal Proj :0.006982644 seconds Reactions :0.01344787 seconds Misc :0.001512175 seconds Base State :5.300012162e-08 seconds Time to advance time step: 0.033948524 Call to estdt for level 0 gives dt_lev = 1.065037272e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 41 gives dt =1e+20 dt_growth factor limits the new dt = 0.01342812062 Timestep 41 starts with TIME = 0.2304142812 DT = 0.01342812062 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.862969069e-29 MLMG: Initial residual (resid0) = 1.862969069e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.751653909e-39, 9.402485193e-11 MLMG: Timers: Solve = 0.004033769 Iter = 0.00383724 Bottom = 0.000154441 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.862969069e-29 MLMG: Initial residual (resid0) = 1.751653909e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000202983 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.728435499e-19 MLMG: Initial residual (resid0) = 7.728435499e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.369817673e-29, 1.772438514e-11 MLMG: Timers: Solve = 0.005998582 Iter = 0.005816713 Bottom = 0.000247783 Done calling nodal solver Timestep 41 ends with TIME = 0.2438424018 DT = 0.01342812062 Timing summary: Advection :0.006557666001 seconds MAC Proj :0.004881281 seconds Nodal Proj :0.006738584 seconds Reactions :0.012157133 seconds Misc :0.001443127 seconds Base State :5.299989425e-08 seconds Time to advance time step: 0.031930579 Call to estdt for level 0 gives dt_lev = 1.015215791e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 42 gives dt =1e+20 dt_growth factor limits the new dt = 0.01409952665 Timestep 42 starts with TIME = 0.2438424018 DT = 0.01409952665 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.957338259e-29 MLMG: Initial residual (resid0) = 1.957338259e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.839075315e-39, 9.395797107e-11 MLMG: Timers: Solve = 0.004004273 Iter = 0.003807694 Bottom = 0.000153204 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.957338259e-29 MLMG: Initial residual (resid0) = 1.839075315e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000205302 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.114857274e-19 MLMG: Initial residual (resid0) = 8.114857274e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.43835189e-29, 1.772491914e-11 MLMG: Timers: Solve = 0.005889733 Iter = 0.005717095 Bottom = 0.000244773 Done calling nodal solver Timestep 42 ends with TIME = 0.2579419285 DT = 0.01409952665 Timing summary: Advection :0.006307084 seconds MAC Proj :0.004844936 seconds Nodal Proj :0.006946893 seconds Reactions :0.012253826 seconds Misc :0.001308122 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.031822163 Call to estdt for level 0 gives dt_lev = 9.67369433e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 43 gives dt =1e+20 dt_growth factor limits the new dt = 0.01480450298 Timestep 43 starts with TIME = 0.2579419285 DT = 0.01480450298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.055380727e-29 MLMG: Initial residual (resid0) = 2.055380727e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.931014507e-39, 9.394923682e-11 MLMG: Timers: Solve = 0.004027914 Iter = 0.003830521 Bottom = 0.000154785 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.055380727e-29 MLMG: Initial residual (resid0) = 1.931014507e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000199699 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.520600138e-19 MLMG: Initial residual (resid0) = 8.520600138e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.510227596e-29, 1.772442752e-11 MLMG: Timers: Solve = 0.005956462 Iter = 0.005780147 Bottom = 0.000245201 Done calling nodal solver Timestep 43 ends with TIME = 0.2727464314 DT = 0.01480450298 Timing summary: Advection :0.005870187 seconds MAC Proj :0.004864392 seconds Nodal Proj :0.006695432 seconds Reactions :0.012309431 seconds Misc :0.001581768 seconds Base State :4.700018508e-08 seconds Time to advance time step: 0.031485054 Call to estdt for level 0 gives dt_lev = 9.21627116e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 44 gives dt =1e+20 dt_growth factor limits the new dt = 0.01554472813 Timestep 44 starts with TIME = 0.2727464314 DT = 0.01554472813 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.158317685e-29 MLMG: Initial residual (resid0) = 2.158317685e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.027620023e-39, 9.394446598e-11 MLMG: Timers: Solve = 0.003996714 Iter = 0.003808878 Bottom = 0.000157899 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.158317685e-29 MLMG: Initial residual (resid0) = 2.027620023e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000201348 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.946630145e-19 MLMG: Initial residual (resid0) = 8.946630145e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.585752938e-29, 1.772458359e-11 MLMG: Timers: Solve = 0.005947652 Iter = 0.005738917 Bottom = 0.000246478 Done calling nodal solver Timestep 44 ends with TIME = 0.2882911596 DT = 0.01554472813 Timing summary: Advection :0.005836907 seconds MAC Proj :0.004850526 seconds Nodal Proj :0.006685609 seconds Reactions :0.012962845 seconds Misc :0.001797482 seconds Base State :7.400012692e-08 seconds Time to advance time step: 0.032299447 Call to estdt for level 0 gives dt_lev = 8.779341895e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 45 gives dt =1e+20 dt_growth factor limits the new dt = 0.01632196453 Timestep 45 starts with TIME = 0.2882911596 DT = 0.01632196453 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.266393495e-29 MLMG: Initial residual (resid0) = 2.266393495e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.128720905e-39, 9.392547718e-11 MLMG: Timers: Solve = 0.004359273 Iter = 0.004156447 Bottom = 0.000153046 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.266393495e-29 MLMG: Initial residual (resid0) = 2.128720905e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000199239 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.053842861e-18 MLMG: Initial residual (resid0) = 1.053842861e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 6.6812532e-29, 6.339895109e-11 MLMG: Timers: Solve = 0.006483681 Iter = 0.006266531 Bottom = 0.000267909 Done calling nodal solver Timestep 45 ends with TIME = 0.3046131241 DT = 0.01632196453 Timing summary: Advection :0.005891518 seconds MAC Proj :0.005329601 seconds Nodal Proj :0.007251801 seconds Reactions :0.011736313 seconds Misc :0.001325717 seconds Base State :4.999992598e-08 seconds Time to advance time step: 0.03170198 Call to estdt for level 0 gives dt_lev = 2.02744569e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 46 gives dt =1e+20 dt_growth factor limits the new dt = 0.01713806276 Timestep 46 starts with TIME = 0.3046131241 DT = 0.01713806276 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 7.013230718e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.386529476e-30, 4.828772376e-11 MLMG: Timers: Solve = 0.00406208 Iter = 0.003858305 Bottom = 0.000157332 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 3.386529476e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000208287 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 9.863659735e-19 MLMG: Initial residual (resid0) = 9.863659735e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.748311055e-29, 1.772477054e-11 MLMG: Timers: Solve = 0.005907967 Iter = 0.005698918 Bottom = 0.00024033 Done calling nodal solver Timestep 46 ends with TIME = 0.3217511869 DT = 0.01713806276 Timing summary: Advection :0.006285115 seconds MAC Proj :0.004957647 seconds Nodal Proj :0.006630099 seconds Reactions :0.012058543 seconds Misc :0.001378403 seconds Base State :4.999992598e-08 seconds Time to advance time step: 0.031469351 Call to estdt for level 0 gives dt_lev = 7.924349732e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 47 gives dt =1e+20 dt_growth factor limits the new dt = 0.0179949659 Timestep 47 starts with TIME = 0.3217511869 DT = 0.0179949659 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.807852852e-29 MLMG: Initial residual (resid0) = 1.807852852e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.37289975e-39, 7.594090129e-11 MLMG: Timers: Solve = 0.004371434 Iter = 0.003934394 Bottom = 0.000154691 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.807852852e-29 MLMG: Initial residual (resid0) = 1.37289975e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000208055 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.035684272e-18 MLMG: Initial residual (resid0) = 1.035684272e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.835690497e-29, 1.772442188e-11 MLMG: Timers: Solve = 0.006105258 Iter = 0.005770699 Bottom = 0.000244934 Done calling nodal solver Timestep 47 ends with TIME = 0.3397461528 DT = 0.0179949659 Timing summary: Advection :0.006142829 seconds MAC Proj :0.005279959 seconds Nodal Proj :0.006870709 seconds Reactions :0.011757217 seconds Misc :0.001394749 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.031609232 Call to estdt for level 0 gives dt_lev = 7.566055076e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 48 gives dt =1e+20 dt_growth factor limits the new dt = 0.01889471419 Timestep 48 starts with TIME = 0.3397461528 DT = 0.01889471419 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.590190152e-29 MLMG: Initial residual (resid0) = 2.590190152e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.464371124e-39, 9.514247908e-11 MLMG: Timers: Solve = 0.004013492 Iter = 0.003816629 Bottom = 0.000154469 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.590190152e-29 MLMG: Initial residual (resid0) = 2.464371124e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000209664 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.087468486e-18 MLMG: Initial residual (resid0) = 1.087468486e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.927461059e-29, 1.772429348e-11 MLMG: Timers: Solve = 0.005923155 Iter = 0.005754892 Bottom = 0.000242063 Done calling nodal solver Timestep 48 ends with TIME = 0.358640867 DT = 0.01889471419 Timing summary: Advection :0.005790788 seconds MAC Proj :0.004870026 seconds Nodal Proj :0.006644727 seconds Reactions :0.012641224 seconds Misc :0.001397084 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.031497178 Call to estdt for level 0 gives dt_lev = 7.214019049e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 49 gives dt =1e+20 dt_growth factor limits the new dt = 0.0198394499 Timestep 49 starts with TIME = 0.358640867 DT = 0.0198394499 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.753963702e-29 MLMG: Initial residual (resid0) = 2.753963702e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.587705007e-39, 9.396293077e-11 MLMG: Timers: Solve = 0.004240255 Iter = 0.003997074 Bottom = 0.000171719 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.753963702e-29 MLMG: Initial residual (resid0) = 2.587682586e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000198823 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.086359695e-18 MLMG: Initial residual (resid0) = 1.086359695e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 4.015978009e-29, 3.69672957e-11 MLMG: Timers: Solve = 0.005899101 Iter = 0.005725607 Bottom = 0.000245112 Done calling nodal solver Timestep 49 ends with TIME = 0.3784803169 DT = 0.0198394499 Timing summary: Advection :0.006130993 seconds MAC Proj :0.005104404 seconds Nodal Proj :0.006619111 seconds Reactions :0.013347304 seconds Misc :0.001457413 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.032819347 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 50 gives dt =1e+20 dt_growth factor limits the new dt = 0.0208314224 Timestep 50 starts with TIME = 0.3784803169 DT = 0.0208314224 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 8.242756114e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.779842146e-30, 4.585653262e-11 MLMG: Timers: Solve = 0.004238641 Iter = 0.004048801 Bottom = 0.000155722 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 3.779842146e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000215565 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.198934006e-18 MLMG: Initial residual (resid0) = 1.198934006e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 2.12508073e-29, 1.772475149e-11 MLMG: Timers: Solve = 0.006431636 Iter = 0.006211157 Bottom = 0.000271842 Done calling nodal solver Timestep 50 ends with TIME = 0.3993117393 DT = 0.0208314224 Timing summary: Advection :0.005748812 seconds MAC Proj :0.005235707 seconds Nodal Proj :0.007186017 seconds Reactions :0.011860501 seconds Misc :0.001404781 seconds Base State :4.700018508e-08 seconds Time to advance time step: 0.031578931 Writing plotfile 50 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.031056907 Writing checkpoint 50 Writing checkpoint chk0000050 Total Time: 3.156902382 Unused ParmParse Variables: [TOP]::maestro.v(nvals = 1) :: [1] [TOP]::amr.check_file(nvals = 1) :: [test_stability_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] AMReX (23.09-22-gb2052f2d2e5c) finalized