Initializing AMReX (24.02-21-g99b47cb58a3c)... MPI initialized with 16 MPI processes MPI initialized with thread support level 0 AMReX (24.02-21-g99b47cb58a3c) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = 5peaks_const_grav.dat model file = 5peaks_const_grav.dat reading initial model 1000 points found in the initial model 10 variables found in the initial model WARNING: variable not found: gravity WARNING: variable not found: abar WARNING: variable not found: zbar WARNING: variable not found: gpot WARNING: variable not found: cno model file mapping, level: 0 dr of MAESTRO base state = 93750000.000000 dr of input file data = 10010010.010010 maximum radius (cell-centered) of input model = 10000000000.000000 WARNING: resolution of base state array is not an integer multiple of the initial model's resolution. make sure this is a desired property as this could lead to aliasing when performing the interpolation. modulus = 3659909.909910 setting r_cutoff to 105 radius at r_cutoff 9890625000 Maximum HSE Error = 0.054171 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile test_stability_pltInitData after InitData inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.01839457 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.000232569 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile test_stability_pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.01709436 Call to firstdt for level 0 gives dt_lev = 0.01907406555 Multiplying dt_lev by init_shrink; dt_lev = 0.001907406555 Minimum firstdt over all levels = 0.001907406555 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 4.945354899e-27 MLMG: Initial residual (resid0) = 4.945354899e-27 MLMG: Final Iter. 3 resid, resid/bnorm = 2.357566962e-30, 0.0004767235133 MLMG: Timers: Solve = 0.002602329 Iter = 0.002327451 Bottom = 9.5242e-05 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 1 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #2 Calling nodal solver MLMG: Initial rhs = 2.306075226e-30 MLMG: Initial residual (resid0) = 2.306075226e-30 MLMG: Final Iter. 5 resid, resid/bnorm = 1.933632021e-37, 8.384947719e-08 MLMG: Timers: Solve = 0.003799885 Iter = 0.003561931 Bottom = 0.000118566 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 2 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #3 Calling nodal solver MLMG: Initial rhs = 9.742172191e-32 MLMG: Initial residual (resid0) = 9.742172191e-32 MLMG: Final Iter. 4 resid, resid/bnorm = 7.521071013e-41, 7.720117101e-10 MLMG: Timers: Solve = 0.002942497 Iter = 0.002723162 Bottom = 0.000108501 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 3 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Writing plotfile test_stability_pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.016037036 Doing initial pressure iteration #1 Timestep 0 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.893547601e-20 MLMG: Initial residual (resid0) = 4.893547601e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 4.517319815e-31, 9.231175792e-12 MLMG: Timers: Solve = 0.004390136 Iter = 0.004126929 Bottom = 0.00011546 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.893547507e-20 MLMG: Initial residual (resid0) = 2.477484298e-27 MLMG: Final Iter. 4 resid, resid/bnorm = 4.813594311e-30, 9.836615062e-11 MLMG: Timers: Solve = 0.002067049 Iter = 0.001825729 Bottom = 5.2512e-05 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.755411273e-17 MLMG: Initial residual (resid0) = 5.755411273e-17 MLMG: Final Iter. 9 resid, resid/bnorm = 1.02012041e-27, 1.772454411e-11 MLMG: Timers: Solve = 0.006440433 Iter = 0.006215276 Bottom = 0.000208409 Done calling nodal solver Timestep 0 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.006240117 seconds MAC Proj :0.00722899 seconds Nodal Proj :0.007230557 seconds Reactions :0.012051599 seconds Misc :0.001758531 seconds Base State :6.499999472e-08 seconds Time to advance time step: 0.038897046 Writing plotfile 0 after all initialization inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.019899084 Writing checkpoint 0 after all initialization Writing checkpoint chk0000000 Calling Evolve() Timestep 1 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.257776127e-26 MLMG: Initial residual (resid0) = 1.257776127e-26 MLMG: Final Iter. 10 resid, resid/bnorm = 1.092411925e-37, 8.685265223e-12 MLMG: Timers: Solve = 0.004937238 Iter = 0.004389894 Bottom = 0.000124929 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.257776127e-26 MLMG: Initial residual (resid0) = 1.092411925e-37 MLMG: No iterations needed MLMG: Timers: Solve = 0.000242253 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.097790919e-19 MLMG: Initial residual (resid0) = 1.097790919e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.945791097e-30, 1.772460551e-11 MLMG: Timers: Solve = 0.006608202 Iter = 0.006397046 Bottom = 0.000238282 Done calling nodal solver Timestep 1 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.00663857 seconds MAC Proj :0.005951027 seconds Nodal Proj :0.007384644 seconds Reactions :0.012413721 seconds Misc :0.002446524 seconds Base State :6.300001587e-08 seconds Time to advance time step: 0.042482208 Call to estdt for level 0 gives dt_lev = 7.191081337e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 2 gives dt =1e+20 dt_growth factor limits the new dt = 0.002002776883 Timestep 2 starts with TIME = 0.001907406555 DT = 0.002002776883 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.080398705e-27 MLMG: Initial residual (resid0) = 8.080398705e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 1.160441939e-37, 1.436119654e-11 MLMG: Timers: Solve = 0.00428648 Iter = 0.004040079 Bottom = 0.000117368 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.498306209e-27 MLMG: Initial residual (resid0) = 2.601349809e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 8.688832515e-37, 9.14777048e-11 MLMG: Timers: Solve = 0.004268564 Iter = 0.004035207 Bottom = 0.000115259 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.096671578e-19 MLMG: Initial residual (resid0) = 1.096671578e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.008844235e-29, 9.19914635e-11 MLMG: Timers: Solve = 0.006258946 Iter = 0.006002261 Bottom = 0.000209598 Done calling nodal solver Timestep 2 ends with TIME = 0.003910183437 DT = 0.002002776883 Timing summary: Advection :0.005965261 seconds MAC Proj :0.009264666 seconds Nodal Proj :0.007059355 seconds Reactions :0.013827987 seconds Misc :0.001541836 seconds Base State :1.000000793e-07 seconds Time to advance time step: 0.037874954 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 3 gives dt =1e+20 dt_growth factor limits the new dt = 0.002102915727 Timestep 3 starts with TIME = 0.003910183437 DT = 0.002102915727 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 8.320997544e-21 MLMG: Final Iter. 10 resid, resid/bnorm = 7.676109766e-31, 9.22498742e-11 MLMG: Timers: Solve = 0.004218401 Iter = 0.004012422 Bottom = 0.000113163 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 7.676109766e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000210325 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.21031446e-19 MLMG: Initial residual (resid0) = 1.21031446e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.145209106e-30, 1.772439458e-11 MLMG: Timers: Solve = 0.006836945 Iter = 0.006625371 Bottom = 0.000212794 Done calling nodal solver Timestep 3 ends with TIME = 0.006013099164 DT = 0.002102915727 Timing summary: Advection :0.005777847 seconds MAC Proj :0.005108847 seconds Nodal Proj :0.007641926 seconds Reactions :0.012532792 seconds Misc :0.001527659 seconds Base State :1.059997885e-07 seconds Time to advance time step: 0.032818025 Call to estdt for level 0 gives dt_lev = 6.528630569e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 4 gives dt =1e+20 dt_growth factor limits the new dt = 0.002208061513 Timestep 4 starts with TIME = 0.006013099164 DT = 0.002208061513 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.308039747e-29 MLMG: Initial residual (resid0) = 1.308039747e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.129752045e-39, 8.636985596e-11 MLMG: Timers: Solve = 0.005742382 Iter = 0.005541611 Bottom = 0.000116189 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.308039747e-29 MLMG: Initial residual (resid0) = 1.129752045e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000609587 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.270830183e-19 MLMG: Initial residual (resid0) = 1.270830183e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.252495441e-30, 1.772459822e-11 MLMG: Timers: Solve = 0.007184664 Iter = 0.006810162 Bottom = 0.000211879 Done calling nodal solver Timestep 4 ends with TIME = 0.008221160677 DT = 0.002208061513 Timing summary: Advection :0.008858369 seconds MAC Proj :0.007436292 seconds Nodal Proj :0.008386651 seconds Reactions :0.018448975 seconds Misc :0.002370635 seconds Base State :9.199993656e-08 seconds Time to advance time step: 0.045747604 Call to estdt for level 0 gives dt_lev = 6.226258359e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 5 gives dt =1e+20 dt_growth factor limits the new dt = 0.002318464589 Timestep 5 starts with TIME = 0.008221160677 DT = 0.002318464589 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.295923274e-30 MLMG: Initial residual (resid0) = 3.295923274e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.024366424e-40, 9.176082608e-11 MLMG: Timers: Solve = 0.004546397 Iter = 0.004301681 Bottom = 0.000118399 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.295923274e-30 MLMG: Initial residual (resid0) = 3.024366424e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000208747 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.334371692e-19 MLMG: Initial residual (resid0) = 1.334371692e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.365138268e-30, 1.772473353e-11 MLMG: Timers: Solve = 0.006049176 Iter = 0.005851756 Bottom = 0.000210447 Done calling nodal solver Timestep 5 ends with TIME = 0.01053962527 DT = 0.002318464589 Timing summary: Advection :0.006120229 seconds MAC Proj :0.00544483 seconds Nodal Proj :0.006819037 seconds Reactions :0.011924426 seconds Misc :0.001572441 seconds Base State :8.100005289e-08 seconds Time to advance time step: 0.03208295 Call to estdt for level 0 gives dt_lev = 5.915049504e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 6 gives dt =1e+20 dt_growth factor limits the new dt = 0.002434387818 Timestep 6 starts with TIME = 0.01053962527 DT = 0.002434387818 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.377753945e-30 MLMG: Initial residual (resid0) = 3.377753945e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.175503469e-40, 9.401227921e-11 MLMG: Timers: Solve = 0.00428314 Iter = 0.00405988 Bottom = 0.000116591 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.377753945e-30 MLMG: Initial residual (resid0) = 3.175499966e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000216981 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.401090277e-19 MLMG: Initial residual (resid0) = 1.401090277e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.483342219e-30, 1.772435552e-11 MLMG: Timers: Solve = 0.006088817 Iter = 0.005891251 Bottom = 0.000207491 Done calling nodal solver Timestep 6 ends with TIME = 0.01297401308 DT = 0.002434387818 Timing summary: Advection :0.006038518 seconds MAC Proj :0.005230437 seconds Nodal Proj :0.006854574 seconds Reactions :0.011942521 seconds Misc :0.001562352001 seconds Base State :9.800010048e-08 seconds Time to advance time step: 0.031833242 Call to estdt for level 0 gives dt_lev = 5.625515433e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 7 gives dt =1e+20 dt_growth factor limits the new dt = 0.002556107209 Timestep 7 starts with TIME = 0.01297401308 DT = 0.002556107209 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.543159178e-30 MLMG: Initial residual (resid0) = 3.543159178e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.334123449e-40, 9.410030095e-11 MLMG: Timers: Solve = 0.004231323 Iter = 0.004011588 Bottom = 0.000116382 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.543159178e-30 MLMG: Initial residual (resid0) = 3.334123449e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000222649 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.471144791e-19 MLMG: Initial residual (resid0) = 1.471144791e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.607516552e-30, 1.772440461e-11 MLMG: Timers: Solve = 0.006161943 Iter = 0.005921881 Bottom = 0.000208022 Done calling nodal solver Timestep 7 ends with TIME = 0.01553012029 DT = 0.002556107209 Timing summary: Advection :0.006126295 seconds MAC Proj :0.005147332 seconds Nodal Proj :0.006978328 seconds Reactions :0.012005922 seconds Misc :0.001557363 seconds Base State :9.300015336e-08 seconds Time to advance time step: 0.032025928 Call to estdt for level 0 gives dt_lev = 5.353255202e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 8 gives dt =1e+20 dt_growth factor limits the new dt = 0.002683912569 Timestep 8 starts with TIME = 0.01553012029 DT = 0.002683912569 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.720271341e-30 MLMG: Initial residual (resid0) = 3.720271341e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.500226363e-40, 9.408524384e-11 MLMG: Timers: Solve = 0.004212576 Iter = 0.004016172 Bottom = 0.00011294 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.720271341e-30 MLMG: Initial residual (resid0) = 3.500226363e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000208939 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.54470203e-19 MLMG: Initial residual (resid0) = 1.54470203e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.737914046e-30, 1.772454488e-11 MLMG: Timers: Solve = 0.006342151 Iter = 0.00613296 Bottom = 0.000210501 Done calling nodal solver Timestep 8 ends with TIME = 0.01821403286 DT = 0.002683912569 Timing summary: Advection :0.006106161 seconds MAC Proj :0.005124501 seconds Nodal Proj :0.00709359 seconds Reactions :0.011839737 seconds Misc :0.001557089 seconds Base State :9.90000899e-08 seconds Time to advance time step: 0.031922508 Call to estdt for level 0 gives dt_lev = 5.095618567e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 9 gives dt =1e+20 dt_growth factor limits the new dt = 0.002818108198 Timestep 9 starts with TIME = 0.01821403286 DT = 0.002818108198 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.90613533e-30 MLMG: Initial residual (resid0) = 3.90613533e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.675781034e-40, 9.410275692e-11 MLMG: Timers: Solve = 0.004202278 Iter = 0.003993828 Bottom = 0.000113909 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.90613533e-30 MLMG: Initial residual (resid0) = 3.675781034e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000213133 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.621937132e-19 MLMG: Initial residual (resid0) = 1.621937132e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.874835628e-30, 1.772470444e-11 MLMG: Timers: Solve = 0.006035365 Iter = 0.005829988 Bottom = 0.000206386 Done calling nodal solver Timestep 9 ends with TIME = 0.02103214106 DT = 0.002818108198 Timing summary: Advection :0.0060302 seconds MAC Proj :0.005098077 seconds Nodal Proj :0.006816282 seconds Reactions :0.011902121 seconds Misc :0.001544997 seconds Base State :9.299992598e-08 seconds Time to advance time step: 0.031590865 Call to estdt for level 0 gives dt_lev = 4.851290067e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 10 gives dt =1e+20 dt_growth factor limits the new dt = 0.002959013608 Timestep 10 starts with TIME = 0.02103214106 DT = 0.002959013608 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.101240383e-30 MLMG: Initial residual (resid0) = 4.101240383e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.859393172e-40, 9.410307155e-11 MLMG: Timers: Solve = 0.004287729 Iter = 0.004067058 Bottom = 0.000116779 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.101240383e-30 MLMG: Initial residual (resid0) = 3.859393172e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000214643 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.703033988e-19 MLMG: Initial residual (resid0) = 1.703033988e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.174814859e-29, 6.898364135e-11 MLMG: Timers: Solve = 0.006406849 Iter = 0.00620014 Bottom = 0.000222095 Done calling nodal solver Timestep 10 ends with TIME = 0.02399115467 DT = 0.002959013608 Timing summary: Advection :0.005969871 seconds MAC Proj :0.005187781 seconds Nodal Proj :0.007146558 seconds Reactions :0.011826502 seconds Misc :0.001564998 seconds Base State :9.300015336e-08 seconds Time to advance time step: 0.031895095 Call to estdt for level 0 gives dt_lev = 1.153498162e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 11 gives dt =1e+20 dt_growth factor limits the new dt = 0.003106964288 Timestep 11 starts with TIME = 0.02399115467 DT = 0.003106964288 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 1.271430598e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.310137768e-31, 4.963021794e-11 MLMG: Timers: Solve = 0.00420884 Iter = 0.004004344 Bottom = 0.000114739 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 6.310137768e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.00024857 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.788185688e-19 MLMG: Initial residual (resid0) = 1.788185688e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.169478835e-30, 1.772455096e-11 MLMG: Timers: Solve = 0.006953516 Iter = 0.006757631 Bottom = 0.000210936 Done calling nodal solver Timestep 11 ends with TIME = 0.02709811896 DT = 0.003106964288 Timing summary: Advection :0.005769599 seconds MAC Proj :0.00515309 seconds Nodal Proj :0.007796041 seconds Reactions :0.011825507 seconds Misc :0.001548211 seconds Base State :9.200016393e-08 seconds Time to advance time step: 0.032323665 Call to estdt for level 0 gives dt_lev = 4.376664086e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 12 gives dt =1e+20 dt_growth factor limits the new dt = 0.003262312503 Timestep 12 starts with TIME = 0.02709811896 DT = 0.003262312503 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.931483508e-30 MLMG: Initial residual (resid0) = 2.931483508e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.211723667e-40, 7.544724916e-11 MLMG: Timers: Solve = 0.004623222 Iter = 0.004382139 Bottom = 0.000113188 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.931483508e-30 MLMG: Initial residual (resid0) = 2.211723667e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00051513 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.877594972e-19 MLMG: Initial residual (resid0) = 1.877594972e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.328006944e-30, 1.772483945e-11 MLMG: Timers: Solve = 0.007794292 Iter = 0.007564422 Bottom = 0.000232718 Done calling nodal solver Timestep 12 ends with TIME = 0.03036043146 DT = 0.003262312503 Timing summary: Advection :0.008002161 seconds MAC Proj :0.006060597 seconds Nodal Proj :0.008688108 seconds Reactions :0.016033146 seconds Misc :0.002015646 seconds Base State :9.399991541e-08 seconds Time to advance time step: 0.041038875 Call to estdt for level 0 gives dt_lev = 4.177466111e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 13 gives dt =1e+20 dt_growth factor limits the new dt = 0.003425428128 Timestep 13 starts with TIME = 0.03036043146 DT = 0.003425428128 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.688771914e-30 MLMG: Initial residual (resid0) = 4.688771914e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.468299394e-40, 9.529786213e-11 MLMG: Timers: Solve = 0.004650087 Iter = 0.004422101 Bottom = 0.000118877 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.688771914e-30 MLMG: Initial residual (resid0) = 4.468299394e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000251136 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.971474721e-19 MLMG: Initial residual (resid0) = 1.971474721e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.494383217e-30, 1.772471734e-11 MLMG: Timers: Solve = 0.006898119 Iter = 0.006696236 Bottom = 0.000221792 Done calling nodal solver Timestep 13 ends with TIME = 0.03378585959 DT = 0.003425428128 Timing summary: Advection :0.006660757 seconds MAC Proj :0.00564376 seconds Nodal Proj :0.007790498 seconds Reactions :0.01427855 seconds Misc :0.001642131 seconds Base State :8.400002116e-08 seconds Time to advance time step: 0.036256375 Call to estdt for level 0 gives dt_lev = 3.982280624e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 14 gives dt =1e+20 dt_growth factor limits the new dt = 0.003596699534 Timestep 14 starts with TIME = 0.03378585959 DT = 0.003596699534 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.983088965e-30 MLMG: Initial residual (resid0) = 4.983088965e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.691428148e-40, 9.414698756e-11 MLMG: Timers: Solve = 0.004700747 Iter = 0.00447751 Bottom = 0.000120244 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.983088965e-30 MLMG: Initial residual (resid0) = 4.691428148e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000351043 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.221658729e-19 MLMG: Initial residual (resid0) = 2.221658729e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.863249975e-30, 3.989474107e-11 MLMG: Timers: Solve = 0.006686502 Iter = 0.006489217 Bottom = 0.000211305 Done calling nodal solver Timestep 14 ends with TIME = 0.03738255912 DT = 0.003596699534 Timing summary: Advection :0.006951305 seconds MAC Proj :0.005821189 seconds Nodal Proj :0.007517648 seconds Reactions :0.013673001 seconds Misc :0.00158774 seconds Base State :9.699988368e-08 seconds Time to advance time step: 0.035768392 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 15 gives dt =1e+20 dt_growth factor limits the new dt = 0.003776534511 Timestep 15 starts with TIME = 0.03738255912 DT = 0.003776534511 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 1.44706648e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 8.547886059e-31, 5.907044478e-11 MLMG: Timers: Solve = 0.004609795 Iter = 0.00438763 Bottom = 0.000116404 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 8.547886059e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022247 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.279163939e-19 MLMG: Initial residual (resid0) = 2.279163939e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.500906095e-29, 6.585336268e-11 MLMG: Timers: Solve = 0.006717613 Iter = 0.00652003 Bottom = 0.000262121 Done calling nodal solver Timestep 15 ends with TIME = 0.04115909363 DT = 0.003776534511 Timing summary: Advection :0.006167437 seconds MAC Proj :0.005576221 seconds Nodal Proj :0.007538437 seconds Reactions :0.013805562 seconds Misc :0.001576378 seconds Base State :1.030000476e-07 seconds Time to advance time step: 0.034877707 Call to estdt for level 0 gives dt_lev = 9.044193233e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 16 gives dt =1e+20 dt_growth factor limits the new dt = 0.003965361236 Timestep 16 starts with TIME = 0.04115909363 DT = 0.003965361236 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 1.62270343e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.18702781e-31, 3.812790245e-11 MLMG: Timers: Solve = 0.004970188 Iter = 0.004744124 Bottom = 0.000116708 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 6.18702781e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000236589 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.282228424e-19 MLMG: Initial residual (resid0) = 2.282228424e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.045151033e-30, 1.772456688e-11 MLMG: Timers: Solve = 0.006839667 Iter = 0.00664373 Bottom = 0.000210813 Done calling nodal solver Timestep 16 ends with TIME = 0.04512445487 DT = 0.003965361236 Timing summary: Advection :0.006209507 seconds MAC Proj :0.005989522 seconds Nodal Proj :0.007650945 seconds Reactions :0.013524861 seconds Misc :0.001576444 seconds Base State :9.099994713e-08 seconds Time to advance time step: 0.0351668 Call to estdt for level 0 gives dt_lev = 3.436593485e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 17 gives dt =1e+20 dt_growth factor limits the new dt = 0.004163629298 Timestep 17 starts with TIME = 0.04512445487 DT = 0.004163629298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.754694364e-30 MLMG: Initial residual (resid0) = 3.754694364e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.825939058e-40, 7.526415691e-11 MLMG: Timers: Solve = 0.00460561 Iter = 0.004381516 Bottom = 0.000119318 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.754694364e-30 MLMG: Initial residual (resid0) = 2.825939058e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000237953 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.396339845e-19 MLMG: Initial residual (resid0) = 2.396339845e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.247301455e-30, 1.772411982e-11 MLMG: Timers: Solve = 0.006891452 Iter = 0.006694836 Bottom = 0.000224212 Done calling nodal solver Timestep 17 ends with TIME = 0.04928808417 DT = 0.004163629298 Timing summary: Advection :0.006301809 seconds MAC Proj :0.005611894 seconds Nodal Proj :0.007732275 seconds Reactions :0.013538982 seconds Misc :0.001900406 seconds Base State :9.600012163e-08 seconds Time to advance time step: 0.035295668 Call to estdt for level 0 gives dt_lev = 3.276898941e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 18 gives dt =1e+20 dt_growth factor limits the new dt = 0.004371810763 Timestep 18 starts with TIME = 0.04928808417 DT = 0.004371810763 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.989009514e-30 MLMG: Initial residual (resid0) = 5.989009514e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.702479003e-40, 9.521572791e-11 MLMG: Timers: Solve = 0.006761929 Iter = 0.006549015 Bottom = 0.000117071 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.989009514e-30 MLMG: Initial residual (resid0) = 5.702479003e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000591105 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.516156837e-19 MLMG: Initial residual (resid0) = 2.516156837e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.459755602e-30, 1.772447383e-11 MLMG: Timers: Solve = 0.007765879 Iter = 0.007333364 Bottom = 0.000217646 Done calling nodal solver Timestep 18 ends with TIME = 0.05365989493 DT = 0.004371810763 Timing summary: Advection :0.00927508 seconds MAC Proj :0.008404214 seconds Nodal Proj :0.009068591 seconds Reactions :0.019043703 seconds Misc :0.00226905 seconds Base State :9.699988368e-08 seconds Time to advance time step: 0.04836908 Call to estdt for level 0 gives dt_lev = 3.122265826e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 19 gives dt =1e+20 dt_growth factor limits the new dt = 0.004590401301 Timestep 19 starts with TIME = 0.05365989493 DT = 0.004590401301 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.361324287e-30 MLMG: Initial residual (resid0) = 6.361324287e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.987979552e-40, 9.413102181e-11 MLMG: Timers: Solve = 0.005103553 Iter = 0.004883871 Bottom = 0.000116684 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.361324287e-30 MLMG: Initial residual (resid0) = 5.987979552e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000224587 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.641964679e-19 MLMG: Initial residual (resid0) = 2.641964679e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.682802363e-30, 1.772469708e-11 MLMG: Timers: Solve = 0.007396851 Iter = 0.007089636 Bottom = 0.00022011 Done calling nodal solver Timestep 19 ends with TIME = 0.05825029623 DT = 0.004590401301 Timing summary: Advection :0.006668619 seconds MAC Proj :0.006095468 seconds Nodal Proj :0.008363052 seconds Reactions :0.014663885 seconds Misc :0.001762479 seconds Base State :1.000000793e-07 seconds Time to advance time step: 0.037770971 Call to estdt for level 0 gives dt_lev = 2.974206455e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 20 gives dt =1e+20 dt_growth factor limits the new dt = 0.004819921366 Timestep 20 starts with TIME = 0.05825029623 DT = 0.004819921366 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.683696559e-30 MLMG: Initial residual (resid0) = 6.683696559e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.287226839e-40, 9.406810713e-11 MLMG: Timers: Solve = 0.004962079 Iter = 0.004730147 Bottom = 0.000115097 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.683696559e-30 MLMG: Initial residual (resid0) = 6.287226839e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000219419 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.774062913e-19 MLMG: Initial residual (resid0) = 2.774062913e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.916899148e-30, 1.772454087e-11 MLMG: Timers: Solve = 0.006874635 Iter = 0.006669594 Bottom = 0.000209544 Done calling nodal solver Timestep 20 ends with TIME = 0.0630702176 DT = 0.004819921366 Timing summary: Advection :0.00728958 seconds MAC Proj :0.005949138 seconds Nodal Proj :0.007685419 seconds Reactions :0.013794032 seconds Misc :0.001645802 seconds Base State :9.199993656e-08 seconds Time to advance time step: 0.036561927 Call to estdt for level 0 gives dt_lev = 2.83287101e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 21 gives dt =1e+20 dt_growth factor limits the new dt = 0.005060917435 Timestep 21 starts with TIME = 0.0630702176 DT = 0.005060917435 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.019131084e-30 MLMG: Initial residual (resid0) = 7.019131084e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.601334897e-40, 9.40477506e-11 MLMG: Timers: Solve = 0.004633866 Iter = 0.004415332 Bottom = 0.000115818 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.019131084e-30 MLMG: Initial residual (resid0) = 6.601334897e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000221709 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.869691725e-19 MLMG: Initial residual (resid0) = 2.869691725e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.297839054e-29, 8.007267937e-11 MLMG: Timers: Solve = 0.006753841 Iter = 0.006527695 Bottom = 0.000233407 Done calling nodal solver Timestep 21 ends with TIME = 0.06813113503 DT = 0.005060917435 Timing summary: Advection :0.006386408 seconds MAC Proj :0.005609465 seconds Nodal Proj :0.007625175 seconds Reactions :0.013762053 seconds Misc :0.001669635 seconds Base State :9.100017451e-08 seconds Time to advance time step: 0.035282848 Call to estdt for level 0 gives dt_lev = 5.895631152e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 22 gives dt =1e+20 dt_growth factor limits the new dt = 0.005313963306 Timestep 22 starts with TIME = 0.06813113503 DT = 0.005313963306 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 2.174577793e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 1.127461332e-30, 5.184736713e-11 MLMG: Timers: Solve = 0.004604587 Iter = 0.004371293 Bottom = 0.000114532 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 1.127461332e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000221002 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.058404362e-19 MLMG: Initial residual (resid0) = 3.058404362e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.420866866e-30, 1.772449364e-11 MLMG: Timers: Solve = 0.006649007 Iter = 0.006443277 Bottom = 0.000209696 Done calling nodal solver Timestep 22 ends with TIME = 0.07344509834 DT = 0.005313963306 Timing summary: Advection :0.006413345 seconds MAC Proj :0.005650621 seconds Nodal Proj :0.007451341 seconds Reactions :0.013543114 seconds Misc :0.001553951 seconds Base State :1.010000688e-07 seconds Time to advance time step: 0.03482669 Call to estdt for level 0 gives dt_lev = 2.554672307e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 23 gives dt =1e+20 dt_growth factor limits the new dt = 0.005579661472 Timestep 23 starts with TIME = 0.07344509834 DT = 0.005579661472 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.733416233e-30 MLMG: Initial residual (resid0) = 7.733416233e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.972214945e-40, 7.722608954e-11 MLMG: Timers: Solve = 0.00479132 Iter = 0.004404225 Bottom = 0.00011656 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.733416233e-30 MLMG: Initial residual (resid0) = 5.972214945e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000198808 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.21132458e-19 MLMG: Initial residual (resid0) = 3.21132458e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.691941506e-30, 1.77245911e-11 MLMG: Timers: Solve = 0.006251222 Iter = 0.00601269 Bottom = 0.000211992 Done calling nodal solver Timestep 23 ends with TIME = 0.07902475981 DT = 0.005579661472 Timing summary: Advection :0.006380939 seconds MAC Proj :0.00573857 seconds Nodal Proj :0.007070163 seconds Reactions :0.012906612 seconds Misc :0.001552885 seconds Base State :9.199993656e-08 seconds Time to advance time step: 0.033859477 Call to estdt for level 0 gives dt_lev = 2.439853595e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 24 gives dt =1e+20 dt_growth factor limits the new dt = 0.005858644545 Timestep 24 starts with TIME = 0.07902475981 DT = 0.005858644545 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.005903751e-30 MLMG: Initial residual (resid0) = 8.005903751e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 7.641995188e-40, 9.54544974e-11 MLMG: Timers: Solve = 0.004052324 Iter = 0.003850325 Bottom = 0.000115835 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.005903751e-30 MLMG: Initial residual (resid0) = 7.641995188e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000210266 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.371890809e-19 MLMG: Initial residual (resid0) = 3.371890809e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.976497655e-30, 1.772446972e-11 MLMG: Timers: Solve = 0.00610924 Iter = 0.005918753 Bottom = 0.000234671 Done calling nodal solver Timestep 24 ends with TIME = 0.08488340435 DT = 0.005858644545 Timing summary: Advection :0.006309361 seconds MAC Proj :0.004975217 seconds Nodal Proj :0.006956913 seconds Reactions :0.011713726 seconds Misc :0.001687058 seconds Base State :9.799987311e-08 seconds Time to advance time step: 0.03186363 Call to estdt for level 0 gives dt_lev = 2.326594909e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 25 gives dt =1e+20 dt_growth factor limits the new dt = 0.006151576773 Timestep 25 starts with TIME = 0.08488340435 DT = 0.006151576773 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.528437685e-30 MLMG: Initial residual (resid0) = 8.528437685e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.023638825e-40, 9.408099257e-11 MLMG: Timers: Solve = 0.004083573 Iter = 0.003871886 Bottom = 0.000114008 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.528437685e-30 MLMG: Initial residual (resid0) = 8.023638825e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000212472 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.540485349e-19 MLMG: Initial residual (resid0) = 3.540485349e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.275401983e-30, 1.772469411e-11 MLMG: Timers: Solve = 0.00683771 Iter = 0.006347348 Bottom = 0.000236844 Done calling nodal solver Timestep 25 ends with TIME = 0.09103498113 DT = 0.006151576773 Timing summary: Advection :0.00630874 seconds MAC Proj :0.005027071 seconds Nodal Proj :0.008060088 seconds Reactions :0.012892207 seconds Misc :0.001878774 seconds Base State :9.200016393e-08 seconds Time to advance time step: 0.034412483 Call to estdt for level 0 gives dt_lev = 2.217290439e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 26 gives dt =1e+20 dt_growth factor limits the new dt = 0.006459155611 Timestep 26 starts with TIME = 0.09103498113 DT = 0.006459155611 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.960898042e-30 MLMG: Initial residual (resid0) = 8.960898042e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.424494264e-40, 9.401395065e-11 MLMG: Timers: Solve = 0.004397149 Iter = 0.003955661 Bottom = 0.000117336 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.960898042e-30 MLMG: Initial residual (resid0) = 8.424494264e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000581973 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.717509617e-19 MLMG: Initial residual (resid0) = 3.717509617e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.589087822e-30, 1.772446746e-11 MLMG: Timers: Solve = 0.007751704 Iter = 0.007374921 Bottom = 0.000235187 Done calling nodal solver Timestep 26 ends with TIME = 0.09749413674 DT = 0.006459155611 Timing summary: Advection :0.007901446 seconds MAC Proj :0.005960754 seconds Nodal Proj :0.009003099 seconds Reactions :0.015323275 seconds Misc :0.002026413 seconds Base State :1.959999736e-07 seconds Time to advance time step: 0.040534194 Call to estdt for level 0 gives dt_lev = 2.112523985e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 27 gives dt =1e+20 dt_growth factor limits the new dt = 0.006782113392 Timestep 27 starts with TIME = 0.09749413674 DT = 0.006782113392 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.409848931e-30 MLMG: Initial residual (resid0) = 9.409848931e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.845794647e-40, 9.400570308e-11 MLMG: Timers: Solve = 0.004495718 Iter = 0.004215216 Bottom = 0.000118604 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.409848931e-30 MLMG: Initial residual (resid0) = 8.845794647e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000212704 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.903385097e-19 MLMG: Initial residual (resid0) = 3.903385097e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.918614436e-30, 1.772465248e-11 MLMG: Timers: Solve = 0.006252367 Iter = 0.006058275 Bottom = 0.000225929 Done calling nodal solver Timestep 27 ends with TIME = 0.1042762501 DT = 0.006782113392 Timing summary: Advection :0.006336607 seconds MAC Proj :0.00545856 seconds Nodal Proj :0.007227246 seconds Reactions :0.012790501 seconds Misc :0.001760937 seconds Base State :9.500013221e-08 seconds Time to advance time step: 0.033784433 Call to estdt for level 0 gives dt_lev = 2.01240705e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 28 gives dt =1e+20 dt_growth factor limits the new dt = 0.007121219061 Timestep 28 starts with TIME = 0.1042762501 DT = 0.007121219061 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.87985185e-30 MLMG: Initial residual (resid0) = 9.87985185e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 9.288212598e-40, 9.401165867e-11 MLMG: Timers: Solve = 0.004094749 Iter = 0.003883852 Bottom = 0.000115327 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.87985185e-30 MLMG: Initial residual (resid0) = 9.288212598e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000213746 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.098554352e-19 MLMG: Initial residual (resid0) = 4.098554352e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.264463305e-30, 1.772445277e-11 MLMG: Timers: Solve = 0.007038302 Iter = 0.006757541 Bottom = 0.000226221 Done calling nodal solver Timestep 28 ends with TIME = 0.1113974692 DT = 0.007121219061 Timing summary: Advection :0.007015049 seconds MAC Proj :0.005053814 seconds Nodal Proj :0.007831474 seconds Reactions :0.012625109 seconds Misc :0.001663959 seconds Base State :9.299992598e-08 seconds Time to advance time step: 0.034402316 Call to estdt for level 0 gives dt_lev = 1.916892684e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 29 gives dt =1e+20 dt_growth factor limits the new dt = 0.007477280014 Timestep 29 starts with TIME = 0.1113974692 DT = 0.007477280014 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.037509187e-29 MLMG: Initial residual (resid0) = 1.037509187e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 9.752953234e-40, 9.400353609e-11 MLMG: Timers: Solve = 0.00435676 Iter = 0.003970014 Bottom = 0.000123174 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.037509187e-29 MLMG: Initial residual (resid0) = 9.752953234e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00020889 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.30348207e-19 MLMG: Initial residual (resid0) = 4.30348207e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.627789989e-30, 1.772469332e-11 MLMG: Timers: Solve = 0.005985933 Iter = 0.005800368 Bottom = 0.000209553 Done calling nodal solver Timestep 29 ends with TIME = 0.1188747492 DT = 0.007477280014 Timing summary: Advection :0.006463376 seconds MAC Proj :0.005284962 seconds Nodal Proj :0.006874469 seconds Reactions :0.013510679 seconds Misc :0.001578484 seconds Base State :9.500013221e-08 seconds Time to advance time step: 0.033967649 Call to estdt for level 0 gives dt_lev = 1.825810886e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 30 gives dt =1e+20 dt_growth factor limits the new dt = 0.007851144015 Timestep 30 starts with TIME = 0.1188747492 DT = 0.007851144015 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.089501496e-29 MLMG: Initial residual (resid0) = 1.089501496e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.024106753e-39, 9.399773718e-11 MLMG: Timers: Solve = 0.004151183 Iter = 0.003943067 Bottom = 0.000114216 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.089501496e-29 MLMG: Initial residual (resid0) = 1.024106753e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00020707 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.518656173e-19 MLMG: Initial residual (resid0) = 4.518656173e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.00907597e-30, 1.772446423e-11 MLMG: Timers: Solve = 0.005942172 Iter = 0.005752877 Bottom = 0.000222121 Done calling nodal solver Timestep 30 ends with TIME = 0.1267258932 DT = 0.007851144015 Timing summary: Advection :0.006074322 seconds MAC Proj :0.005131174 seconds Nodal Proj :0.006747357 seconds Reactions :0.011924957 seconds Misc :0.001912936 seconds Base State :9.299992598e-08 seconds Time to advance time step: 0.032024367 Call to estdt for level 0 gives dt_lev = 1.738995247e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 31 gives dt =1e+20 dt_growth factor limits the new dt = 0.008243701216 Timestep 31 starts with TIME = 0.1267258932 DT = 0.008243701216 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.144079624e-29 MLMG: Initial residual (resid0) = 1.144079624e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.075258351e-39, 9.398457314e-11 MLMG: Timers: Solve = 0.004079656 Iter = 0.003865533 Bottom = 0.000118355 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.144079624e-29 MLMG: Initial residual (resid0) = 1.075258351e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000199462 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.744588982e-19 MLMG: Initial residual (resid0) = 4.744588982e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.409669399e-30, 1.772475852e-11 MLMG: Timers: Solve = 0.006092401 Iter = 0.005847793 Bottom = 0.00021754 Done calling nodal solver Timestep 31 ends with TIME = 0.1349695944 DT = 0.008243701216 Timing summary: Advection :0.005986159 seconds MAC Proj :0.004969628 seconds Nodal Proj :0.006860729 seconds Reactions :0.012064208 seconds Misc :0.001485684 seconds Base State :1.980001798e-07 seconds Time to advance time step: 0.031568839 Call to estdt for level 0 gives dt_lev = 1.656260551e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 32 gives dt =1e+20 dt_growth factor limits the new dt = 0.008655886277 Timestep 32 starts with TIME = 0.1349695944 DT = 0.008655886277 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.201372446e-29 MLMG: Initial residual (resid0) = 1.201372446e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.129010758e-39, 9.397674818e-11 MLMG: Timers: Solve = 0.004105565 Iter = 0.003871573 Bottom = 0.000114925 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.201372446e-29 MLMG: Initial residual (resid0) = 1.129010758e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000215103 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.981818431e-19 MLMG: Initial residual (resid0) = 4.981818431e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.830148054e-30, 1.772474886e-11 MLMG: Timers: Solve = 0.006561163 Iter = 0.006373448 Bottom = 0.000218361 Done calling nodal solver Timestep 32 ends with TIME = 0.1436254807 DT = 0.008655886277 Timing summary: Advection :0.006320266 seconds MAC Proj :0.004989508 seconds Nodal Proj :0.007363283 seconds Reactions :0.011855068 seconds Misc :0.001466102 seconds Base State :8.999995771e-08 seconds Time to advance time step: 0.032230644 Call to estdt for level 0 gives dt_lev = 1.577440861e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 33 gives dt =1e+20 dt_growth factor limits the new dt = 0.00908868059 Timestep 33 starts with TIME = 0.1436254807 DT = 0.00908868059 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.261567528e-29 MLMG: Initial residual (resid0) = 1.261567528e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.185462067e-39, 9.396738906e-11 MLMG: Timers: Solve = 0.004586986 Iter = 0.004382469 Bottom = 0.000113816 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.261567528e-29 MLMG: Initial residual (resid0) = 1.185462067e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00021318 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.230909353e-19 MLMG: Initial residual (resid0) = 5.230909353e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.271474901e-30, 1.772440368e-11 MLMG: Timers: Solve = 0.008760283 Iter = 0.0082967 Bottom = 0.000242222 Done calling nodal solver Timestep 33 ends with TIME = 0.1527141613 DT = 0.00908868059 Timing summary: Advection :0.006273289 seconds MAC Proj :0.005472141 seconds Nodal Proj :0.0100824 seconds Reactions :0.013064126 seconds Misc :0.00146517 seconds Base State :9.199993656e-08 seconds Time to advance time step: 0.036616382 Call to estdt for level 0 gives dt_lev = 1.502378414e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 34 gives dt =1e+20 dt_growth factor limits the new dt = 0.00954311462 Timestep 34 starts with TIME = 0.1527141613 DT = 0.00954311462 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.324582667e-29 MLMG: Initial residual (resid0) = 1.324582667e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.244696354e-39, 9.396894474e-11 MLMG: Timers: Solve = 0.005078831 Iter = 0.004837818 Bottom = 0.000118401 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.324582667e-29 MLMG: Initial residual (resid0) = 1.244696354e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000211793 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.49245482e-19 MLMG: Initial residual (resid0) = 5.49245482e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.735238831e-30, 1.772474995e-11 MLMG: Timers: Solve = 0.006249815 Iter = 0.006023121 Bottom = 0.000209485 Done calling nodal solver Timestep 34 ends with TIME = 0.1622572759 DT = 0.00954311462 Timing summary: Advection :0.006796882 seconds MAC Proj :0.005992507 seconds Nodal Proj :0.007280132 seconds Reactions :0.015989359 seconds Misc :0.001801912 seconds Base State :8.899996828e-08 seconds Time to advance time step: 0.038076199 Call to estdt for level 0 gives dt_lev = 1.430880358e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 35 gives dt =1e+20 dt_growth factor limits the new dt = 0.01002027035 Timestep 35 starts with TIME = 0.1622572759 DT = 0.01002027035 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.390963587e-29 MLMG: Initial residual (resid0) = 1.390963587e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.306904197e-39, 9.395675121e-11 MLMG: Timers: Solve = 0.004132945 Iter = 0.003923615 Bottom = 0.000118481 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.390963587e-29 MLMG: Initial residual (resid0) = 1.306904197e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000205231 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.681793327e-19 MLMG: Initial residual (resid0) = 5.681793327e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.54956653e-29, 8.00727212e-11 MLMG: Timers: Solve = 0.006418405 Iter = 0.006216949 Bottom = 0.000223471 Done calling nodal solver Timestep 35 ends with TIME = 0.1722775463 DT = 0.01002027035 Timing summary: Advection :0.005984809 seconds MAC Proj :0.005003111 seconds Nodal Proj :0.00730228 seconds Reactions :0.012121683 seconds Misc :0.001907868 seconds Base State :8.999995771e-08 seconds Time to advance time step: 0.032557128 Call to estdt for level 0 gives dt_lev = 2.977695677e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 36 gives dt =1e+20 dt_growth factor limits the new dt = 0.01052128387 Timestep 36 starts with TIME = 0.1722775463 DT = 0.01052128387 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 4.305515288e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.23205761e-30, 5.184182289e-11 MLMG: Timers: Solve = 0.004084501 Iter = 0.003885021 Bottom = 0.000117018 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 2.23205761e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000202598 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.055431439e-19 MLMG: Initial residual (resid0) = 6.055431439e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.073301499e-29, 1.772460822e-11 MLMG: Timers: Solve = 0.006126089 Iter = 0.005938414 Bottom = 0.000227808 Done calling nodal solver Timestep 36 ends with TIME = 0.1827988301 DT = 0.01052128387 Timing summary: Advection :0.005605956 seconds MAC Proj :0.004962491 seconds Nodal Proj :0.006906272 seconds Reactions :0.012682792 seconds Misc :0.001494055 seconds Base State :9.600012163e-08 seconds Time to advance time step: 0.031861025 Call to estdt for level 0 gives dt_lev = 1.290254218e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 37 gives dt =1e+20 dt_growth factor limits the new dt = 0.01104734806 Timestep 37 starts with TIME = 0.1827988301 DT = 0.01104734806 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.53169484e-29 MLMG: Initial residual (resid0) = 1.53169484e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.182368e-39, 7.719344411e-11 MLMG: Timers: Solve = 0.004615506 Iter = 0.004414135 Bottom = 0.000115109 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.53169484e-29 MLMG: Initial residual (resid0) = 1.182368e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022982 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.264177143e-19 MLMG: Initial residual (resid0) = 6.264177143e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.855307908e-29, 7.75091093e-11 MLMG: Timers: Solve = 0.006424012 Iter = 0.006223734 Bottom = 0.000214385 Done calling nodal solver Timestep 37 ends with TIME = 0.1938461782 DT = 0.01104734806 Timing summary: Advection :0.005793001 seconds MAC Proj :0.005512936 seconds Nodal Proj :0.007212643 seconds Reactions :0.012006437 seconds Misc :0.001419332001 seconds Base State :9.700011105e-08 seconds Time to advance time step: 0.032149789 Call to estdt for level 0 gives dt_lev = 2.789559822e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 38 gives dt =1e+20 dt_growth factor limits the new dt = 0.01159971547 Timestep 38 starts with TIME = 0.1938461782 DT = 0.01159971547 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 4.746830605e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.490741235e-30, 5.247166883e-11 MLMG: Timers: Solve = 0.004091166 Iter = 0.003885686 Bottom = 0.000116222 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 2.490741235e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.00020535 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.676113162e-19 MLMG: Initial residual (resid0) = 6.676113162e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.183315432e-29, 1.772461615e-11 MLMG: Timers: Solve = 0.006057909 Iter = 0.005868585 Bottom = 0.000211505 Done calling nodal solver Timestep 38 ends with TIME = 0.2054458937 DT = 0.01159971547 Timing summary: Advection :0.006152903 seconds MAC Proj :0.004992916 seconds Nodal Proj :0.006852783 seconds Reactions :0.011970049 seconds Misc :0.001470347 seconds Base State :7.800008461e-08 seconds Time to advance time step: 0.031648205 Call to estdt for level 0 gives dt_lev = 1.168429834e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 39 gives dt =1e+20 dt_growth factor limits the new dt = 0.01217970124 Timestep 39 starts with TIME = 0.2054458937 DT = 0.01217970124 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.536277128e-29 MLMG: Initial residual (resid0) = 1.536277128e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.179416865e-39, 7.677110101e-11 MLMG: Timers: Solve = 0.004133191 Iter = 0.003893128 Bottom = 0.000113912 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.536277128e-29 MLMG: Initial residual (resid0) = 1.179416865e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000198699 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.00991882e-19 MLMG: Initial residual (resid0) = 7.00991882e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.242475185e-29, 1.77245303e-11 MLMG: Timers: Solve = 0.005973749 Iter = 0.005774012 Bottom = 0.000222728 Done calling nodal solver Timestep 39 ends with TIME = 0.2176255949 DT = 0.01217970124 Timing summary: Advection :0.006088821 seconds MAC Proj :0.004998906 seconds Nodal Proj :0.007110772 seconds Reactions :0.0124996 seconds Misc :0.001542537 seconds Base State :8.899996828e-08 seconds Time to advance time step: 0.032460391 Call to estdt for level 0 gives dt_lev = 1.116506554e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 40 gives dt =1e+20 dt_growth factor limits the new dt = 0.0127886863 Timestep 40 starts with TIME = 0.2176255949 DT = 0.0127886863 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.750089547e-29 MLMG: Initial residual (resid0) = 1.750089547e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.668229006e-39, 9.532249417e-11 MLMG: Timers: Solve = 0.004067643 Iter = 0.003864558 Bottom = 0.000116499 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.750089547e-29 MLMG: Initial residual (resid0) = 1.668229006e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000508896 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.360414761e-19 MLMG: Initial residual (resid0) = 7.360414761e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.304586426e-29, 1.772436022e-11 MLMG: Timers: Solve = 0.006418566 Iter = 0.006159626 Bottom = 0.000211079 Done calling nodal solver Timestep 40 ends with TIME = 0.2304142812 DT = 0.0127886863 Timing summary: Advection :0.007673578 seconds MAC Proj :0.005435299 seconds Nodal Proj :0.007321134 seconds Reactions :0.016187619 seconds Misc :0.002250451 seconds Base State :9.299992598e-08 seconds Time to advance time step: 0.039110647 Call to estdt for level 0 gives dt_lev = 1.065037272e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 41 gives dt =1e+20 dt_growth factor limits the new dt = 0.01342812062 Timestep 41 starts with TIME = 0.2304142812 DT = 0.01342812062 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.862969069e-29 MLMG: Initial residual (resid0) = 1.862969069e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.751653909e-39, 9.402485193e-11 MLMG: Timers: Solve = 0.004062242 Iter = 0.003850381 Bottom = 0.000116188 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.862969069e-29 MLMG: Initial residual (resid0) = 1.751653909e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.0002003 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.728435499e-19 MLMG: Initial residual (resid0) = 7.728435499e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.369817673e-29, 1.772438514e-11 MLMG: Timers: Solve = 0.008657809 Iter = 0.008197036 Bottom = 0.00021603 Done calling nodal solver Timestep 41 ends with TIME = 0.2438424018 DT = 0.01342812062 Timing summary: Advection :0.006332204 seconds MAC Proj :0.004927022 seconds Nodal Proj :0.009932978 seconds Reactions :0.014746123 seconds Misc :0.001566708 seconds Base State :9.399991541e-08 seconds Time to advance time step: 0.037772826 Call to estdt for level 0 gives dt_lev = 1.015215791e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 42 gives dt =1e+20 dt_growth factor limits the new dt = 0.01409952665 Timestep 42 starts with TIME = 0.2438424018 DT = 0.01409952665 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.957338259e-29 MLMG: Initial residual (resid0) = 1.957338259e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.839075315e-39, 9.395797107e-11 MLMG: Timers: Solve = 0.004439988 Iter = 0.004201172 Bottom = 0.000121386 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.957338259e-29 MLMG: Initial residual (resid0) = 1.839075315e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.0003726 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.114857274e-19 MLMG: Initial residual (resid0) = 8.114857274e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.43835189e-29, 1.772491914e-11 MLMG: Timers: Solve = 0.006531579 Iter = 0.006327386 Bottom = 0.000232808 Done calling nodal solver Timestep 42 ends with TIME = 0.2579419285 DT = 0.01409952665 Timing summary: Advection :0.006313154 seconds MAC Proj :0.00556915 seconds Nodal Proj :0.007305947 seconds Reactions :0.01540831 seconds Misc :0.001784757 seconds Base State :8.400002116e-08 seconds Time to advance time step: 0.036607743 Call to estdt for level 0 gives dt_lev = 9.67369433e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 43 gives dt =1e+20 dt_growth factor limits the new dt = 0.01480450298 Timestep 43 starts with TIME = 0.2579419285 DT = 0.01480450298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.055380727e-29 MLMG: Initial residual (resid0) = 2.055380727e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.931014507e-39, 9.394923682e-11 MLMG: Timers: Solve = 0.004104641 Iter = 0.003904174 Bottom = 0.000115889 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.055380727e-29 MLMG: Initial residual (resid0) = 1.931014507e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000198478 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.520600138e-19 MLMG: Initial residual (resid0) = 8.520600138e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.510227596e-29, 1.772442752e-11 MLMG: Timers: Solve = 0.005976043 Iter = 0.005768459 Bottom = 0.000208888 Done calling nodal solver Timestep 43 ends with TIME = 0.2727464314 DT = 0.01480450298 Timing summary: Advection :0.00629739 seconds MAC Proj :0.004983437 seconds Nodal Proj :0.006755337 seconds Reactions :0.0119507 seconds Misc :0.001617451 seconds Base State :8.500001059e-08 seconds Time to advance time step: 0.031810021 Call to estdt for level 0 gives dt_lev = 9.21627116e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 44 gives dt =1e+20 dt_growth factor limits the new dt = 0.01554472813 Timestep 44 starts with TIME = 0.2727464314 DT = 0.01554472813 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.158317685e-29 MLMG: Initial residual (resid0) = 2.158317685e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.027620023e-39, 9.394446598e-11 MLMG: Timers: Solve = 0.00460642 Iter = 0.004401986 Bottom = 0.000116602 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.158317685e-29 MLMG: Initial residual (resid0) = 2.027620023e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000206583 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.946630145e-19 MLMG: Initial residual (resid0) = 8.946630145e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.585752938e-29, 1.772458359e-11 MLMG: Timers: Solve = 0.006191402 Iter = 0.005998464 Bottom = 0.000205221 Done calling nodal solver Timestep 44 ends with TIME = 0.2882911596 DT = 0.01554472813 Timing summary: Advection :0.005904042 seconds MAC Proj :0.005471922 seconds Nodal Proj :0.006948941 seconds Reactions :0.011802024 seconds Misc :0.001475352 seconds Base State :9.699988368e-08 seconds Time to advance time step: 0.031816275 Call to estdt for level 0 gives dt_lev = 8.779341895e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 45 gives dt =1e+20 dt_growth factor limits the new dt = 0.01632196453 Timestep 45 starts with TIME = 0.2882911596 DT = 0.01632196453 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.266393495e-29 MLMG: Initial residual (resid0) = 2.266393495e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.128720905e-39, 9.392547718e-11 MLMG: Timers: Solve = 0.004074177 Iter = 0.003873335 Bottom = 0.000114734 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.266393495e-29 MLMG: Initial residual (resid0) = 2.128720905e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000205059 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.053842861e-18 MLMG: Initial residual (resid0) = 1.053842861e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 6.6812532e-29, 6.339895109e-11 MLMG: Timers: Solve = 0.005932969 Iter = 0.005729834 Bottom = 0.000209249 Done calling nodal solver Timestep 45 ends with TIME = 0.3046131241 DT = 0.01632196453 Timing summary: Advection :0.006073845 seconds MAC Proj :0.004945103 seconds Nodal Proj :0.006711692 seconds Reactions :0.012232758 seconds Misc :0.001521422 seconds Base State :8.200004231e-08 seconds Time to advance time step: 0.031698565 Call to estdt for level 0 gives dt_lev = 2.02744569e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 46 gives dt =1e+20 dt_growth factor limits the new dt = 0.01713806276 Timestep 46 starts with TIME = 0.3046131241 DT = 0.01713806276 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 7.013230718e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.386529476e-30, 4.828772376e-11 MLMG: Timers: Solve = 0.004105031 Iter = 0.003904272 Bottom = 0.00011394 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 3.386529476e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000200001 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 9.863659735e-19 MLMG: Initial residual (resid0) = 9.863659735e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.748311055e-29, 1.772477054e-11 MLMG: Timers: Solve = 0.005927006 Iter = 0.005737242 Bottom = 0.000222568 Done calling nodal solver Timestep 46 ends with TIME = 0.3217511869 DT = 0.01713806276 Timing summary: Advection :0.005664204 seconds MAC Proj :0.004997846 seconds Nodal Proj :0.006682667 seconds Reactions :0.013317573 seconds Misc :0.00146113 seconds Base State :8.000006346e-08 seconds Time to advance time step: 0.032338519 Call to estdt for level 0 gives dt_lev = 7.924349732e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 47 gives dt =1e+20 dt_growth factor limits the new dt = 0.0179949659 Timestep 47 starts with TIME = 0.3217511869 DT = 0.0179949659 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.807852852e-29 MLMG: Initial residual (resid0) = 1.807852852e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.37289975e-39, 7.594090129e-11 MLMG: Timers: Solve = 0.004087289 Iter = 0.003872859 Bottom = 0.000118095 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.807852852e-29 MLMG: Initial residual (resid0) = 1.37289975e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000197887 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.035684272e-18 MLMG: Initial residual (resid0) = 1.035684272e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.835690497e-29, 1.772442188e-11 MLMG: Timers: Solve = 0.006373293 Iter = 0.006181744 Bottom = 0.000210081 Done calling nodal solver Timestep 47 ends with TIME = 0.3397461528 DT = 0.0179949659 Timing summary: Advection :0.006250039 seconds MAC Proj :0.004950444 seconds Nodal Proj :0.007206323 seconds Reactions :0.011792731 seconds Misc :0.001558806 seconds Base State :8.600000001e-08 seconds Time to advance time step: 0.031976407 Call to estdt for level 0 gives dt_lev = 7.566055076e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 48 gives dt =1e+20 dt_growth factor limits the new dt = 0.01889471419 Timestep 48 starts with TIME = 0.3397461528 DT = 0.01889471419 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.590190152e-29 MLMG: Initial residual (resid0) = 2.590190152e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.464371124e-39, 9.514247908e-11 MLMG: Timers: Solve = 0.004070799 Iter = 0.003868852 Bottom = 0.000113383 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.590190152e-29 MLMG: Initial residual (resid0) = 2.464371124e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000198797 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.087468486e-18 MLMG: Initial residual (resid0) = 1.087468486e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.927461059e-29, 1.772429348e-11 MLMG: Timers: Solve = 0.008808347 Iter = 0.008335899 Bottom = 0.000246414 Done calling nodal solver Timestep 48 ends with TIME = 0.358640867 DT = 0.01889471419 Timing summary: Advection :0.006287464 seconds MAC Proj :0.004948748 seconds Nodal Proj :0.010048754 seconds Reactions :0.011977962 seconds Misc :0.001550246 seconds Base State :7.199992069e-08 seconds Time to advance time step: 0.03508903 Call to estdt for level 0 gives dt_lev = 7.214019049e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 49 gives dt =1e+20 dt_growth factor limits the new dt = 0.0198394499 Timestep 49 starts with TIME = 0.358640867 DT = 0.0198394499 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.753963702e-29 MLMG: Initial residual (resid0) = 2.753963702e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.587705007e-39, 9.396293077e-11 MLMG: Timers: Solve = 0.005907711 Iter = 0.005405459 Bottom = 0.000119293 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.753963702e-29 MLMG: Initial residual (resid0) = 2.587682586e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000243561 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.086359695e-18 MLMG: Initial residual (resid0) = 1.086359695e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 4.015978009e-29, 3.69672957e-11 MLMG: Timers: Solve = 0.006273561 Iter = 0.006079259 Bottom = 0.0002239 Done calling nodal solver Timestep 49 ends with TIME = 0.3784803169 DT = 0.0198394499 Timing summary: Advection :0.006659618 seconds MAC Proj :0.00687828 seconds Nodal Proj :0.007058134 seconds Reactions :0.015750707 seconds Misc :0.001797618 seconds Base State :9.200016393e-08 seconds Time to advance time step: 0.038369809 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 50 gives dt =1e+20 dt_growth factor limits the new dt = 0.0208314224 Timestep 50 starts with TIME = 0.3784803169 DT = 0.0208314224 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 8.242756114e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.779842146e-30, 4.585653262e-11 MLMG: Timers: Solve = 0.004133163 Iter = 0.003922712 Bottom = 0.00012092 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 3.779842146e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.0002092 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.198934006e-18 MLMG: Initial residual (resid0) = 1.198934006e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 2.12508073e-29, 1.772475149e-11 MLMG: Timers: Solve = 0.006173199 Iter = 0.005941572 Bottom = 0.000213365 Done calling nodal solver Timestep 50 ends with TIME = 0.3993117393 DT = 0.0208314224 Timing summary: Advection :0.005843593 seconds MAC Proj :0.005043401 seconds Nodal Proj :0.006930513 seconds Reactions :0.012315022 seconds Misc :0.001619744 seconds Base State :1.119999524e-07 seconds Time to advance time step: 0.03197146 Writing plotfile 50 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.016823259 Writing checkpoint 50 Writing checkpoint chk0000050 Total Time: 3.68946266 Unused ParmParse Variables: [TOP]::maestro.v(nvals = 1) :: [1] [TOP]::amr.check_file(nvals = 1) :: [test_stability_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] AMReX (24.02-21-g99b47cb58a3c) finalized