Initializing AMReX (v2024-34-g9e8f8d60eca3)... MPI initialized with 16 MPI processes MPI initialized with thread support level 0 AMReX (v2024-34-g9e8f8d60eca3) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = 5peaks_const_grav.dat model file = 5peaks_const_grav.dat reading initial model 1000 points found in the initial model 10 variables found in the initial model WARNING: variable not found: gravity WARNING: variable not found: abar WARNING: variable not found: zbar WARNING: variable not found: gpot WARNING: variable not found: cno model file mapping, level: 0 dr of MAESTRO base state = 93750000.000000 dr of input file data = 10010010.010010 maximum radius (cell-centered) of input model = 10000000000.000000 WARNING: resolution of base state array is not an integer multiple of the initial model's resolution. make sure this is a desired property as this could lead to aliasing when performing the interpolation. modulus = 3659909.909910 setting r_cutoff to 105 radius at r_cutoff 9890625000 Maximum HSE Error = 0.054171 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile test_stability_pltInitData after InitData inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.017075579 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.000341566 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile test_stability_pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.016482059 Call to firstdt for level 0 gives dt_lev = 0.01907406555 Multiplying dt_lev by init_shrink; dt_lev = 0.001907406555 Minimum firstdt over all levels = 0.001907406555 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 4.945354899e-27 MLMG: Initial residual (resid0) = 4.945354899e-27 MLMG: Final Iter. 3 resid, resid/bnorm = 2.357566962e-30, 0.0004767235133 MLMG: Timers: Solve = 0.002902142 Iter = 0.0026545 Bottom = 8.6101e-05 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 1 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #2 Calling nodal solver MLMG: Initial rhs = 2.306075226e-30 MLMG: Initial residual (resid0) = 2.306075226e-30 MLMG: Final Iter. 5 resid, resid/bnorm = 1.933642558e-37, 8.384993415e-08 MLMG: Timers: Solve = 0.0042679 Iter = 0.004049514 Bottom = 0.000162888 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 2 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #3 Calling nodal solver MLMG: Initial rhs = 9.742172194e-32 MLMG: Initial residual (resid0) = 9.742172194e-32 MLMG: Final Iter. 4 resid, resid/bnorm = 7.56277059e-41, 7.76292026e-10 MLMG: Timers: Solve = 0.003308156 Iter = 0.003087118 Bottom = 0.000109907 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 3 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Writing plotfile test_stability_pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.01776397 Doing initial pressure iteration #1 Timestep 0 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.893547601e-20 MLMG: Initial residual (resid0) = 4.893547601e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 4.517319639e-31, 9.231175431e-12 MLMG: Timers: Solve = 0.017191942 Iter = 0.014019852 Bottom = 0.000129475 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.893547507e-20 MLMG: Initial residual (resid0) = 2.477484298e-27 MLMG: Final Iter. 4 resid, resid/bnorm = 4.813594317e-30, 9.836615074e-11 MLMG: Timers: Solve = 0.002371544 Iter = 0.002137146 Bottom = 5.7291e-05 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.755411273e-17 MLMG: Initial residual (resid0) = 5.755411273e-17 MLMG: Final Iter. 9 resid, resid/bnorm = 1.020114247e-27, 1.772443703e-11 MLMG: Timers: Solve = 0.007210692 Iter = 0.006841034 Bottom = 0.000221789 Done calling nodal solver Timestep 0 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.011111906 seconds MAC Proj :0.020500091 seconds Nodal Proj :0.011487949 seconds Reactions :0.01541188 seconds Misc :0.001664587 seconds Base State :5.49998731e-08 seconds Time to advance time step: 0.064493581 Writing plotfile 0 after all initialization inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.013616797 Writing checkpoint 0 after all initialization Writing checkpoint chk0000000 Calling Evolve() Timestep 1 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.257776132e-26 MLMG: Initial residual (resid0) = 1.257776132e-26 MLMG: Final Iter. 10 resid, resid/bnorm = 1.092354528e-37, 8.684808849e-12 MLMG: Timers: Solve = 0.005978992 Iter = 0.005681099 Bottom = 0.000150399 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.257776132e-26 MLMG: Initial residual (resid0) = 1.092354528e-37 MLMG: No iterations needed MLMG: Timers: Solve = 0.000274373 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.097790919e-19 MLMG: Initial residual (resid0) = 1.097790919e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.945791097e-30, 1.772460551e-11 MLMG: Timers: Solve = 0.007423214 Iter = 0.00718173 Bottom = 0.000252288 Done calling nodal solver Timestep 1 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.006828105 seconds MAC Proj :0.007133474 seconds Nodal Proj :0.008229412 seconds Reactions :0.016326873 seconds Misc :0.002056584 seconds Base State :6.00000476e-08 seconds Time to advance time step: 0.047578746 Call to estdt for level 0 gives dt_lev = 7.191087425e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 2 gives dt =1e+20 dt_growth factor limits the new dt = 0.002002776883 Timestep 2 starts with TIME = 0.001907406555 DT = 0.002002776883 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.08039884e-27 MLMG: Initial residual (resid0) = 8.08039884e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 1.160384542e-37, 1.436048597e-11 MLMG: Timers: Solve = 0.005674225 Iter = 0.005148627 Bottom = 0.000123278 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.498306041e-27 MLMG: Initial residual (resid0) = 2.601349809e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 8.687490856e-37, 9.146358118e-11 MLMG: Timers: Solve = 0.010784708 Iter = 0.01038065 Bottom = 0.000157707 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.096671578e-19 MLMG: Initial residual (resid0) = 1.096671578e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.008841827e-29, 9.199124398e-11 MLMG: Timers: Solve = 0.007323476 Iter = 0.007010679 Bottom = 0.00022189 Done calling nodal solver Timestep 2 ends with TIME = 0.003910183437 DT = 0.002002776883 Timing summary: Advection :0.011556987 seconds MAC Proj :0.021311795 seconds Nodal Proj :0.008304878 seconds Reactions :0.016314057 seconds Misc :0.001660564 seconds Base State :6.300001587e-08 seconds Time to advance time step: 0.059352907 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 3 gives dt =1e+20 dt_growth factor limits the new dt = 0.002102915727 Timestep 3 starts with TIME = 0.003910183437 DT = 0.002102915727 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 8.320997544e-21 MLMG: Final Iter. 10 resid, resid/bnorm = 7.677524121e-31, 9.226687161e-11 MLMG: Timers: Solve = 0.005729027 Iter = 0.005499118 Bottom = 0.000126094 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 7.677524121e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000233691 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.21031446e-19 MLMG: Initial residual (resid0) = 1.21031446e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.145245217e-30, 1.772469294e-11 MLMG: Timers: Solve = 0.007209857 Iter = 0.00700802 Bottom = 0.0002268 Done calling nodal solver Timestep 3 ends with TIME = 0.006013099164 DT = 0.002102915727 Timing summary: Advection :0.006548959 seconds MAC Proj :0.006703562 seconds Nodal Proj :0.007989881 seconds Reactions :0.012136988 seconds Misc :0.001752072 seconds Base State :5.09999154e-08 seconds Time to advance time step: 0.035274459 Call to estdt for level 0 gives dt_lev = 6.528670715e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 4 gives dt =1e+20 dt_growth factor limits the new dt = 0.002208061513 Timestep 4 starts with TIME = 0.006013099164 DT = 0.002208061513 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.3079729e-29 MLMG: Initial residual (resid0) = 1.3079729e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.129684783e-39, 8.63691276e-11 MLMG: Timers: Solve = 0.005276236 Iter = 0.005061925 Bottom = 0.000119547 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.3079729e-29 MLMG: Initial residual (resid0) = 1.129684783e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000230432 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.270830183e-19 MLMG: Initial residual (resid0) = 1.270830183e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.252519515e-30, 1.772478766e-11 MLMG: Timers: Solve = 0.007246466 Iter = 0.007040087 Bottom = 0.000234053 Done calling nodal solver Timestep 4 ends with TIME = 0.008221160677 DT = 0.002208061513 Timing summary: Advection :0.006525182 seconds MAC Proj :0.006248071 seconds Nodal Proj :0.008111201 seconds Reactions :0.012881121 seconds Misc :0.001483708 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.035419384 Call to estdt for level 0 gives dt_lev = 6.226377027e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 5 gives dt =1e+20 dt_growth factor limits the new dt = 0.002318464589 Timestep 5 starts with TIME = 0.008221160677 DT = 0.002318464589 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.295423824e-30 MLMG: Initial residual (resid0) = 3.295423824e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.024461011e-40, 9.177760352e-11 MLMG: Timers: Solve = 0.005318099 Iter = 0.005095364 Bottom = 0.00012171 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.295423824e-30 MLMG: Initial residual (resid0) = 3.024461011e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000234661 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.334371692e-19 MLMG: Initial residual (resid0) = 1.334371692e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.365126231e-30, 1.772464333e-11 MLMG: Timers: Solve = 0.007230669 Iter = 0.006999934 Bottom = 0.000268323 Done calling nodal solver Timestep 5 ends with TIME = 0.01053962527 DT = 0.002318464589 Timing summary: Advection :0.007093885 seconds MAC Proj :0.006316948 seconds Nodal Proj :0.008033677 seconds Reactions :0.012243681 seconds Misc :0.001520748 seconds Base State :7.599987839e-08 seconds Time to advance time step: 0.035355086 Call to estdt for level 0 gives dt_lev = 5.914991835e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 6 gives dt =1e+20 dt_growth factor limits the new dt = 0.002434387818 Timestep 6 starts with TIME = 0.01053962527 DT = 0.002434387818 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.377300377e-30 MLMG: Initial residual (resid0) = 3.377300377e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.175447418e-40, 9.402324529e-11 MLMG: Timers: Solve = 0.005289575 Iter = 0.005063677 Bottom = 0.00013697 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.377300377e-30 MLMG: Initial residual (resid0) = 3.175443914e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000225466 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.401090277e-19 MLMG: Initial residual (resid0) = 1.401090277e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.483390367e-30, 1.772469917e-11 MLMG: Timers: Solve = 0.007050747 Iter = 0.006824759 Bottom = 0.000217342 Done calling nodal solver Timestep 6 ends with TIME = 0.01297401308 DT = 0.002434387818 Timing summary: Advection :0.006685329 seconds MAC Proj :0.006249982 seconds Nodal Proj :0.007831981 seconds Reactions :0.013272091 seconds Misc :0.001501609 seconds Base State :5.300012162e-08 seconds Time to advance time step: 0.035684771 Call to estdt for level 0 gives dt_lev = 5.625582499e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 7 gives dt =1e+20 dt_growth factor limits the new dt = 0.002556107209 Timestep 7 starts with TIME = 0.01297401308 DT = 0.002556107209 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.542867857e-30 MLMG: Initial residual (resid0) = 3.542867857e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.33382217e-40, 9.409953474e-11 MLMG: Timers: Solve = 0.005754888 Iter = 0.005538155 Bottom = 0.000120804 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.542867857e-30 MLMG: Initial residual (resid0) = 3.33382217e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000215925 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.471144791e-19 MLMG: Initial residual (resid0) = 1.471144791e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.607576737e-30, 1.772481372e-11 MLMG: Timers: Solve = 0.007178399 Iter = 0.006804539 Bottom = 0.000217506 Done calling nodal solver Timestep 7 ends with TIME = 0.01553012029 DT = 0.002556107209 Timing summary: Advection :0.006578933 seconds MAC Proj :0.006720497 seconds Nodal Proj :0.008036031 seconds Reactions :0.012056178 seconds Misc :0.001495799 seconds Base State :3.279999419e-07 seconds Time to advance time step: 0.035030325 Call to estdt for level 0 gives dt_lev = 5.353302437e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 8 gives dt =1e+20 dt_growth factor limits the new dt = 0.002683912569 Timestep 8 starts with TIME = 0.01553012029 DT = 0.002683912569 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.719890133e-30 MLMG: Initial residual (resid0) = 3.719890133e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.500289421e-40, 9.409658071e-11 MLMG: Timers: Solve = 0.005293742 Iter = 0.005071521 Bottom = 0.000124789 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.719890133e-30 MLMG: Initial residual (resid0) = 3.500289421e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000262928 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.54470203e-19 MLMG: Initial residual (resid0) = 1.54470203e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.737926083e-30, 1.77246228e-11 MLMG: Timers: Solve = 0.007520818 Iter = 0.00728528 Bottom = 0.000239001 Done calling nodal solver Timestep 8 ends with TIME = 0.01821403286 DT = 0.002683912569 Timing summary: Advection :0.006832893 seconds MAC Proj :0.006321628 seconds Nodal Proj :0.008300646 seconds Reactions :0.013422527 seconds Misc :0.001686497 seconds Base State :5.299989425e-08 seconds Time to advance time step: 0.036702122 Call to estdt for level 0 gives dt_lev = 5.095587997e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 9 gives dt =1e+20 dt_growth factor limits the new dt = 0.002818108198 Timestep 9 starts with TIME = 0.01821403286 DT = 0.002818108198 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.905661102e-30 MLMG: Initial residual (resid0) = 3.905661102e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.676397606e-40, 9.412996953e-11 MLMG: Timers: Solve = 0.005336784 Iter = 0.005085934 Bottom = 0.000121633 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.905661102e-30 MLMG: Initial residual (resid0) = 3.676397606e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022235 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.621937132e-19 MLMG: Initial residual (resid0) = 1.621937132e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.874823591e-30, 1.772463022e-11 MLMG: Timers: Solve = 0.006922743 Iter = 0.006722962 Bottom = 0.000227637 Done calling nodal solver Timestep 9 ends with TIME = 0.02103214106 DT = 0.002818108198 Timing summary: Advection :0.006641533 seconds MAC Proj :0.006310708 seconds Nodal Proj :0.007731258 seconds Reactions :0.012810545 seconds Misc :0.001488554 seconds Base State :5.900005817e-08 seconds Time to advance time step: 0.035119812 Call to estdt for level 0 gives dt_lev = 4.851262359e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 10 gives dt =1e+20 dt_growth factor limits the new dt = 0.002959013608 Timestep 10 starts with TIME = 0.02103214106 DT = 0.002959013608 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.100939546e-30 MLMG: Initial residual (resid0) = 4.100939546e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.860100828e-40, 9.412723071e-11 MLMG: Timers: Solve = 0.005287888 Iter = 0.005069875 Bottom = 0.000120824 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.100939546e-30 MLMG: Initial residual (resid0) = 3.860100828e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000231257 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.703033988e-19 MLMG: Initial residual (resid0) = 1.703033988e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.174813655e-29, 6.898357067e-11 MLMG: Timers: Solve = 0.007189991 Iter = 0.006991047 Bottom = 0.000224036 Done calling nodal solver Timestep 10 ends with TIME = 0.02399115467 DT = 0.002959013608 Timing summary: Advection :0.006680165 seconds MAC Proj :0.006294988 seconds Nodal Proj :0.007986894 seconds Reactions :0.013030518 seconds Misc :0.001743021 seconds Base State :5.000015335e-08 seconds Time to advance time step: 0.035880297 Call to estdt for level 0 gives dt_lev = 1.153494089e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 11 gives dt =1e+20 dt_growth factor limits the new dt = 0.003106964288 Timestep 11 starts with TIME = 0.02399115467 DT = 0.003106964288 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 1.271430598e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.310351499e-31, 4.963189897e-11 MLMG: Timers: Solve = 0.005757227 Iter = 0.005521685 Bottom = 0.000122488 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 6.310351499e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000215182 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.788185688e-19 MLMG: Initial residual (resid0) = 1.788185688e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.169478835e-30, 1.772455096e-11 MLMG: Timers: Solve = 0.006979583 Iter = 0.006760416 Bottom = 0.000224625 Done calling nodal solver Timestep 11 ends with TIME = 0.02709811896 DT = 0.003106964288 Timing summary: Advection :0.006436764 seconds MAC Proj :0.006710801 seconds Nodal Proj :0.008095221 seconds Reactions :0.012389458 seconds Misc :0.001510795 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.035291308 Call to estdt for level 0 gives dt_lev = 4.376646045e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 12 gives dt =1e+20 dt_growth factor limits the new dt = 0.003262312503 Timestep 12 starts with TIME = 0.02709811896 DT = 0.003262312503 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.931087603e-30 MLMG: Initial residual (resid0) = 2.931087603e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.211756947e-40, 7.545857536e-11 MLMG: Timers: Solve = 0.005391322 Iter = 0.005173684 Bottom = 0.000122042 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.931087603e-30 MLMG: Initial residual (resid0) = 2.211756947e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00020878 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.877594972e-19 MLMG: Initial residual (resid0) = 1.877594972e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.327886573e-30, 1.772419836e-11 MLMG: Timers: Solve = 0.007234928 Iter = 0.007035132 Bottom = 0.000227066 Done calling nodal solver Timestep 12 ends with TIME = 0.03036043146 DT = 0.003262312503 Timing summary: Advection :0.006750607 seconds MAC Proj :0.006446142 seconds Nodal Proj :0.008023732 seconds Reactions :0.012096353 seconds Misc :0.001522936 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.034981387 Call to estdt for level 0 gives dt_lev = 4.177453783e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 13 gives dt =1e+20 dt_growth factor limits the new dt = 0.003425428128 Timestep 13 starts with TIME = 0.03036043146 DT = 0.003425428128 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.688248856e-30 MLMG: Initial residual (resid0) = 4.688248856e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.467598744e-40, 9.52935495e-11 MLMG: Timers: Solve = 0.005352234 Iter = 0.005139899 Bottom = 0.000118676 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.688248856e-30 MLMG: Initial residual (resid0) = 4.467598744e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000219964 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.971474721e-19 MLMG: Initial residual (resid0) = 1.971474721e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.494310995e-30, 1.7724351e-11 MLMG: Timers: Solve = 0.00718184 Iter = 0.00697869 Bottom = 0.000227185 Done calling nodal solver Timestep 13 ends with TIME = 0.03378585959 DT = 0.003425428128 Timing summary: Advection :0.006566019 seconds MAC Proj :0.00632766 seconds Nodal Proj :0.00796989 seconds Reactions :0.012921248 seconds Misc :0.001494002 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.035415741 Call to estdt for level 0 gives dt_lev = 3.982247017e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 14 gives dt =1e+20 dt_growth factor limits the new dt = 0.003596699534 Timestep 14 starts with TIME = 0.03378585959 DT = 0.003596699534 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.98227213e-30 MLMG: Initial residual (resid0) = 4.98227213e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.691855544e-40, 9.417100114e-11 MLMG: Timers: Solve = 0.005275486 Iter = 0.00504789 Bottom = 0.00012114 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.98227213e-30 MLMG: Initial residual (resid0) = 4.691855544e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000229317 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.221658729e-19 MLMG: Initial residual (resid0) = 2.221658729e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.863225901e-30, 3.989463271e-11 MLMG: Timers: Solve = 0.007039323 Iter = 0.006840095 Bottom = 0.000236813 Done calling nodal solver Timestep 14 ends with TIME = 0.03738255912 DT = 0.003596699534 Timing summary: Advection :0.007131258 seconds MAC Proj :0.006268602 seconds Nodal Proj :0.007817403 seconds Reactions :0.012911771 seconds Misc :0.001563035 seconds Base State :4.599996828e-08 seconds Time to advance time step: 0.035833124 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 15 gives dt =1e+20 dt_growth factor limits the new dt = 0.003776534511 Timestep 15 starts with TIME = 0.03738255912 DT = 0.003776534511 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 1.44706648e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 8.546351457e-31, 5.905983986e-11 MLMG: Timers: Solve = 0.005283754 Iter = 0.005073649 Bottom = 0.000123367 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 8.546351457e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000216456 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.279163939e-19 MLMG: Initial residual (resid0) = 2.279163939e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.500913317e-29, 6.585367956e-11 MLMG: Timers: Solve = 0.007204326 Iter = 0.00698269 Bottom = 0.000222249 Done calling nodal solver Timestep 15 ends with TIME = 0.04115909363 DT = 0.003776534511 Timing summary: Advection :0.006492962 seconds MAC Proj :0.00622355 seconds Nodal Proj :0.008011216 seconds Reactions :0.013690881 seconds Misc :0.001540845 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.036101696 Call to estdt for level 0 gives dt_lev = 9.044183602e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 16 gives dt =1e+20 dt_growth factor limits the new dt = 0.003965361236 Timestep 16 starts with TIME = 0.04115909363 DT = 0.003965361236 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 1.62270343e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.18605137e-31, 3.812188509e-11 MLMG: Timers: Solve = 0.005703357 Iter = 0.00549111 Bottom = 0.000118778 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 6.18605137e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000231657 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.282228424e-19 MLMG: Initial residual (resid0) = 2.282228424e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.045223255e-30, 1.772488333e-11 MLMG: Timers: Solve = 0.007241299 Iter = 0.007035626 Bottom = 0.000222079 Done calling nodal solver Timestep 16 ends with TIME = 0.04512445487 DT = 0.003965361236 Timing summary: Advection :0.006376193 seconds MAC Proj :0.006711305 seconds Nodal Proj :0.008022122 seconds Reactions :0.01222901 seconds Misc :0.001524075 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.034999676 Call to estdt for level 0 gives dt_lev = 3.436635199e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 17 gives dt =1e+20 dt_growth factor limits the new dt = 0.004163629298 Timestep 17 starts with TIME = 0.04512445487 DT = 0.004163629298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.754712132e-30 MLMG: Initial residual (resid0) = 3.754712132e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.82584447e-40, 7.526128158e-11 MLMG: Timers: Solve = 0.005271633 Iter = 0.005061105 Bottom = 0.000138035 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.754712132e-30 MLMG: Initial residual (resid0) = 2.82584447e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000229868 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.396339845e-19 MLMG: Initial residual (resid0) = 2.396339845e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.247421825e-30, 1.772462213e-11 MLMG: Timers: Solve = 0.007164817 Iter = 0.006960167 Bottom = 0.000212775 Done calling nodal solver Timestep 17 ends with TIME = 0.04928808417 DT = 0.004163629298 Timing summary: Advection :0.006501766 seconds MAC Proj :0.006249601 seconds Nodal Proj :0.007933478 seconds Reactions :0.013028807 seconds Misc :0.001507907 seconds Base State :5.399988368e-08 seconds Time to advance time step: 0.0353649 Call to estdt for level 0 gives dt_lev = 3.276873657e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 18 gives dt =1e+20 dt_growth factor limits the new dt = 0.004371810763 Timestep 18 starts with TIME = 0.04928808417 DT = 0.004371810763 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.988437125e-30 MLMG: Initial residual (resid0) = 5.988437125e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.701673257e-40, 9.521137381e-11 MLMG: Timers: Solve = 0.005276138 Iter = 0.005055295 Bottom = 0.000122423 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.988437125e-30 MLMG: Initial residual (resid0) = 5.701673257e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000267436 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.516156837e-19 MLMG: Initial residual (resid0) = 2.516156837e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.459779676e-30, 1.772456951e-11 MLMG: Timers: Solve = 0.006923497 Iter = 0.006691339 Bottom = 0.000214327 Done calling nodal solver Timestep 18 ends with TIME = 0.05365989493 DT = 0.004371810763 Timing summary: Advection :0.007174095 seconds MAC Proj :0.006321082 seconds Nodal Proj :0.00770585 seconds Reactions :0.012468217 seconds Misc :0.001494491 seconds Base State :4.900016393e-08 seconds Time to advance time step: 0.035304307 Call to estdt for level 0 gives dt_lev = 3.122293372e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 19 gives dt =1e+20 dt_growth factor limits the new dt = 0.004590401301 Timestep 19 starts with TIME = 0.05365989493 DT = 0.004590401301 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.361637466e-30 MLMG: Initial residual (resid0) = 6.361637466e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.987748338e-40, 9.41227533e-11 MLMG: Timers: Solve = 0.005478923 Iter = 0.005222519 Bottom = 0.000143051 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.361637466e-30 MLMG: Initial residual (resid0) = 5.987748338e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000274517 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.641964679e-19 MLMG: Initial residual (resid0) = 2.641964679e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.68289866e-30, 1.772506157e-11 MLMG: Timers: Solve = 0.007085191 Iter = 0.006848936 Bottom = 0.000237484 Done calling nodal solver Timestep 19 ends with TIME = 0.05825029623 DT = 0.004590401301 Timing summary: Advection :0.006695636 seconds MAC Proj :0.006563637 seconds Nodal Proj :0.007899125 seconds Reactions :0.013908472 seconds Misc :0.001524218 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.036728828 Call to estdt for level 0 gives dt_lev = 2.974235616e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 20 gives dt =1e+20 dt_growth factor limits the new dt = 0.004819921366 Timestep 20 starts with TIME = 0.05825029623 DT = 0.004819921366 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.682786498e-30 MLMG: Initial residual (resid0) = 6.682786498e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.287114735e-40, 9.407923982e-11 MLMG: Timers: Solve = 0.005726427 Iter = 0.005506203 Bottom = 0.000122611 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.682786498e-30 MLMG: Initial residual (resid0) = 6.287114735e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000240248 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.774062913e-19 MLMG: Initial residual (resid0) = 2.774062913e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.916875074e-30, 1.772445409e-11 MLMG: Timers: Solve = 0.007072528 Iter = 0.006830054 Bottom = 0.000216241 Done calling nodal solver Timestep 20 ends with TIME = 0.0630702176 DT = 0.004819921366 Timing summary: Advection :0.006967126 seconds MAC Proj :0.006732896 seconds Nodal Proj :0.008187752 seconds Reactions :0.011993365 seconds Misc :0.001518971 seconds Base State :5.60000899e-08 seconds Time to advance time step: 0.035535041 Call to estdt for level 0 gives dt_lev = 2.832901245e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 21 gives dt =1e+20 dt_growth factor limits the new dt = 0.005060917435 Timestep 21 starts with TIME = 0.0630702176 DT = 0.005060917435 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.017767486e-30 MLMG: Initial residual (resid0) = 7.017767486e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.601040624e-40, 9.406183144e-11 MLMG: Timers: Solve = 0.005282149 Iter = 0.005070892 Bottom = 0.000120746 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.017767486e-30 MLMG: Initial residual (resid0) = 6.601040624e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000231753 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.869691725e-19 MLMG: Initial residual (resid0) = 2.869691725e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.297839054e-29, 8.007267937e-11 MLMG: Timers: Solve = 0.00752765 Iter = 0.007311389 Bottom = 0.000220783 Done calling nodal solver Timestep 21 ends with TIME = 0.06813113503 DT = 0.005060917435 Timing summary: Advection :0.00729575 seconds MAC Proj :0.006298962 seconds Nodal Proj :0.008324363 seconds Reactions :0.012672867 seconds Misc :0.001474362 seconds Base State :4.80001745e-08 seconds Time to advance time step: 0.03621921 Call to estdt for level 0 gives dt_lev = 5.895649157e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 22 gives dt =1e+20 dt_growth factor limits the new dt = 0.005313963306 Timestep 22 starts with TIME = 0.06813113503 DT = 0.005313963306 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 2.174577793e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 1.127453232e-30, 5.184699467e-11 MLMG: Timers: Solve = 0.005720787 Iter = 0.005485032 Bottom = 0.000122308 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 1.127453232e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000220909 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.058404362e-19 MLMG: Initial residual (resid0) = 3.058404362e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.420842792e-30, 1.772441493e-11 MLMG: Timers: Solve = 0.00724569 Iter = 0.007043976 Bottom = 0.000235688 Done calling nodal solver Timestep 22 ends with TIME = 0.07344509834 DT = 0.005313963306 Timing summary: Advection :0.006598931 seconds MAC Proj :0.006700092 seconds Nodal Proj :0.008088885 seconds Reactions :0.014008556 seconds Misc :0.001502968 seconds Base State :5.20001322e-08 seconds Time to advance time step: 0.037083539 Call to estdt for level 0 gives dt_lev = 2.554660013e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 23 gives dt =1e+20 dt_growth factor limits the new dt = 0.005579661472 Timestep 23 starts with TIME = 0.07344509834 DT = 0.005579661472 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.73348257e-30 MLMG: Initial residual (resid0) = 7.73348257e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.972845529e-40, 7.723358105e-11 MLMG: Timers: Solve = 0.005268436 Iter = 0.005056974 Bottom = 0.000121342 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.73348257e-30 MLMG: Initial residual (resid0) = 5.972845529e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00033662 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.21132458e-19 MLMG: Initial residual (resid0) = 3.21132458e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.691941506e-30, 1.77245911e-11 MLMG: Timers: Solve = 0.00705016 Iter = 0.006848336 Bottom = 0.000224629 Done calling nodal solver Timestep 23 ends with TIME = 0.07902475981 DT = 0.005579661472 Timing summary: Advection :0.006898005 seconds MAC Proj :0.006389008 seconds Nodal Proj :0.007854533 seconds Reactions :0.012380585 seconds Misc :0.001543236 seconds Base State :3.249999736e-07 seconds Time to advance time step: 0.035204667 Call to estdt for level 0 gives dt_lev = 2.439862005e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 24 gives dt =1e+20 dt_growth factor limits the new dt = 0.005858644545 Timestep 24 starts with TIME = 0.07902475981 DT = 0.005858644545 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.00564811e-30 MLMG: Initial residual (resid0) = 8.00564811e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 7.641742954e-40, 9.545439482e-11 MLMG: Timers: Solve = 0.005283729 Iter = 0.005061516 Bottom = 0.000120905 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.00564811e-30 MLMG: Initial residual (resid0) = 7.641742954e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000214179 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.371890809e-19 MLMG: Initial residual (resid0) = 3.371890809e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.976593952e-30, 1.772475531e-11 MLMG: Timers: Solve = 0.007129642 Iter = 0.006881713 Bottom = 0.000228128 Done calling nodal solver Timestep 24 ends with TIME = 0.08488340435 DT = 0.005858644545 Timing summary: Advection :0.006507345 seconds MAC Proj :0.006246008 seconds Nodal Proj :0.007933322 seconds Reactions :0.013274123 seconds Misc :0.001788179 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.035885251 Call to estdt for level 0 gives dt_lev = 2.326582163e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 25 gives dt =1e+20 dt_growth factor limits the new dt = 0.006151576773 Timestep 25 starts with TIME = 0.08488340435 DT = 0.006151576773 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.527771313e-30 MLMG: Initial residual (resid0) = 8.527771313e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.024857955e-40, 9.410264019e-11 MLMG: Timers: Solve = 0.005742049 Iter = 0.005520494 Bottom = 0.000120546 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.527771313e-30 MLMG: Initial residual (resid0) = 8.024857955e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000222159 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.540485349e-19 MLMG: Initial residual (resid0) = 3.540485349e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.275353834e-30, 1.772455812e-11 MLMG: Timers: Solve = 0.007391394 Iter = 0.007028844 Bottom = 0.000217212 Done calling nodal solver Timestep 25 ends with TIME = 0.09103498113 DT = 0.006151576773 Timing summary: Advection :0.006534737 seconds MAC Proj :0.006700781 seconds Nodal Proj :0.008235562 seconds Reactions :0.012409368 seconds Misc :0.001509646999 seconds Base State :4.900016393e-08 seconds Time to advance time step: 0.035542942 Call to estdt for level 0 gives dt_lev = 2.21729507e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 26 gives dt =1e+20 dt_growth factor limits the new dt = 0.006459155611 Timestep 26 starts with TIME = 0.09103498113 DT = 0.006459155611 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.960012316e-30 MLMG: Initial residual (resid0) = 8.960012316e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.424844588e-40, 9.402715411e-11 MLMG: Timers: Solve = 0.005284058 Iter = 0.00507189 Bottom = 0.000120867 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.960012316e-30 MLMG: Initial residual (resid0) = 8.424844588e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000495668 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.717509617e-19 MLMG: Initial residual (resid0) = 3.717509617e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.58913597e-30, 1.772459698e-11 MLMG: Timers: Solve = 0.007259439 Iter = 0.007059047 Bottom = 0.000230701 Done calling nodal solver Timestep 26 ends with TIME = 0.09749413674 DT = 0.006459155611 Timing summary: Advection :0.0069674 seconds MAC Proj :0.006643424 seconds Nodal Proj :0.008046265 seconds Reactions :0.012294824 seconds Misc :0.00156247 seconds Base State :4.69999577e-08 seconds Time to advance time step: 0.035654095 Call to estdt for level 0 gives dt_lev = 2.112511375e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 27 gives dt =1e+20 dt_growth factor limits the new dt = 0.006782113392 Timestep 27 starts with TIME = 0.09749413674 DT = 0.006782113392 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.408830982e-30 MLMG: Initial residual (resid0) = 9.408830982e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.846691478e-40, 9.402540544e-11 MLMG: Timers: Solve = 0.005285553 Iter = 0.005072266 Bottom = 0.000120496 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.408830982e-30 MLMG: Initial residual (resid0) = 8.846691478e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000218346 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.903385097e-19 MLMG: Initial residual (resid0) = 3.903385097e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.918614436e-30, 1.772465248e-11 MLMG: Timers: Solve = 0.007248676 Iter = 0.007037837 Bottom = 0.00022581 Done calling nodal solver Timestep 27 ends with TIME = 0.1042762501 DT = 0.006782113392 Timing summary: Advection :0.006614291 seconds MAC Proj :0.006234596 seconds Nodal Proj :0.008056338 seconds Reactions :0.012755186 seconds Misc :0.001503117 seconds Base State :5.100014278e-08 seconds Time to advance time step: 0.035306212 Call to estdt for level 0 gives dt_lev = 2.0124204e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 28 gives dt =1e+20 dt_growth factor limits the new dt = 0.007121219061 Timestep 28 starts with TIME = 0.1042762501 DT = 0.007121219061 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.880130395e-30 MLMG: Initial residual (resid0) = 9.880130395e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 9.288520884e-40, 9.40121285e-11 MLMG: Timers: Solve = 0.005267558 Iter = 0.005054437 Bottom = 0.000118796 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.880130395e-30 MLMG: Initial residual (resid0) = 9.288520884e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000238373 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.098554352e-19 MLMG: Initial residual (resid0) = 4.098554352e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.264511454e-30, 1.772457025e-11 MLMG: Timers: Solve = 0.006993676 Iter = 0.006784017 Bottom = 0.000226837 Done calling nodal solver Timestep 28 ends with TIME = 0.1113974692 DT = 0.007121219061 Timing summary: Advection :0.006836476 seconds MAC Proj :0.00630078 seconds Nodal Proj :0.007760509 seconds Reactions :0.012729627 seconds Misc :0.001589254 seconds Base State :6.799996299e-08 seconds Time to advance time step: 0.035351567 Call to estdt for level 0 gives dt_lev = 1.916904797e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 29 gives dt =1e+20 dt_growth factor limits the new dt = 0.007477280014 Timestep 29 starts with TIME = 0.1113974692 DT = 0.007477280014 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.037425901e-29 MLMG: Initial residual (resid0) = 1.037425901e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 9.752925208e-40, 9.401081271e-11 MLMG: Timers: Solve = 0.005741772 Iter = 0.005305995 Bottom = 0.000120204 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.037425901e-29 MLMG: Initial residual (resid0) = 9.752925208e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000229471 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.30348207e-19 MLMG: Initial residual (resid0) = 4.30348207e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.627838138e-30, 1.77248052e-11 MLMG: Timers: Solve = 0.007169184 Iter = 0.006960082 Bottom = 0.000223629 Done calling nodal solver Timestep 29 ends with TIME = 0.1188747492 DT = 0.007477280014 Timing summary: Advection :0.006619927 seconds MAC Proj :0.006805382 seconds Nodal Proj :0.007976377 seconds Reactions :0.012909815 seconds Misc :0.001524278001 seconds Base State :5.700007932e-08 seconds Time to advance time step: 0.035981707 Call to estdt for level 0 gives dt_lev = 1.825812456e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 30 gives dt =1e+20 dt_growth factor limits the new dt = 0.007851144015 Timestep 30 starts with TIME = 0.1188747492 DT = 0.007851144015 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.08944873e-29 MLMG: Initial residual (resid0) = 1.08944873e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.023977833e-39, 9.399045635e-11 MLMG: Timers: Solve = 0.00575813 Iter = 0.005546607 Bottom = 0.000121295 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.08944873e-29 MLMG: Initial residual (resid0) = 1.023977833e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000229529 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.518656173e-19 MLMG: Initial residual (resid0) = 4.518656173e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.00907597e-30, 1.772446423e-11 MLMG: Timers: Solve = 0.007086128 Iter = 0.006878799 Bottom = 0.000221005 Done calling nodal solver Timestep 30 ends with TIME = 0.1267258932 DT = 0.007851144015 Timing summary: Advection :0.006617879 seconds MAC Proj :0.00676521 seconds Nodal Proj :0.00787376 seconds Reactions :0.011969943 seconds Misc :0.001533606 seconds Base State :5.400011105e-08 seconds Time to advance time step: 0.034902231 Call to estdt for level 0 gives dt_lev = 1.738989551e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 31 gives dt =1e+20 dt_growth factor limits the new dt = 0.008243701216 Timestep 31 starts with TIME = 0.1267258932 DT = 0.008243701216 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.143997884e-29 MLMG: Initial residual (resid0) = 1.143997884e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.075244338e-39, 9.399006352e-11 MLMG: Timers: Solve = 0.005277563 Iter = 0.005069101 Bottom = 0.000118166 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.143997884e-29 MLMG: Initial residual (resid0) = 1.075244338e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000219064 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.744588982e-19 MLMG: Initial residual (resid0) = 4.744588982e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.409524954e-30, 1.772445408e-11 MLMG: Timers: Solve = 0.007036507 Iter = 0.006836531 Bottom = 0.00021831 Done calling nodal solver Timestep 31 ends with TIME = 0.1349695944 DT = 0.008243701216 Timing summary: Advection :0.006382291 seconds MAC Proj :0.006219143 seconds Nodal Proj :0.007892085 seconds Reactions :0.012731816 seconds Misc :0.00150931 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.034905934 Call to estdt for level 0 gives dt_lev = 1.656272178e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 32 gives dt =1e+20 dt_growth factor limits the new dt = 0.008655886277 Timestep 32 starts with TIME = 0.1349695944 DT = 0.008655886277 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.20132055e-29 MLMG: Initial residual (resid0) = 1.20132055e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.128845405e-39, 9.396704365e-11 MLMG: Timers: Solve = 0.005277605 Iter = 0.005060153 Bottom = 0.000138348 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.20132055e-29 MLMG: Initial residual (resid0) = 1.128845405e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000213824 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.981818431e-19 MLMG: Initial residual (resid0) = 4.981818431e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.830051757e-30, 1.772455556e-11 MLMG: Timers: Solve = 0.006983626 Iter = 0.006781926 Bottom = 0.000223016 Done calling nodal solver Timestep 32 ends with TIME = 0.1436254807 DT = 0.008655886277 Timing summary: Advection :0.00686665 seconds MAC Proj :0.006206337 seconds Nodal Proj :0.007766216 seconds Reactions :0.012010003 seconds Misc :0.001559735 seconds Base State :8.300003174e-08 seconds Time to advance time step: 0.034564453 Call to estdt for level 0 gives dt_lev = 1.57745258e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 33 gives dt =1e+20 dt_growth factor limits the new dt = 0.00908868059 Timestep 33 starts with TIME = 0.1436254807 DT = 0.00908868059 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.261518372e-29 MLMG: Initial residual (resid0) = 1.261518372e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.185446653e-39, 9.396982869e-11 MLMG: Timers: Solve = 0.005691802 Iter = 0.005242104 Bottom = 0.000122507 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.261518372e-29 MLMG: Initial residual (resid0) = 1.185446653e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000216035 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.230909353e-19 MLMG: Initial residual (resid0) = 5.230909353e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.271571197e-30, 1.772458778e-11 MLMG: Timers: Solve = 0.007113939 Iter = 0.006909681 Bottom = 0.000230115 Done calling nodal solver Timestep 33 ends with TIME = 0.1527141613 DT = 0.00908868059 Timing summary: Advection :0.006677802 seconds MAC Proj :0.006670798 seconds Nodal Proj :0.008118521 seconds Reactions :0.012272352 seconds Misc :0.001497175 seconds Base State :4.700018508e-08 seconds Time to advance time step: 0.035379721 Call to estdt for level 0 gives dt_lev = 1.502382666e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 34 gives dt =1e+20 dt_growth factor limits the new dt = 0.00954311462 Timestep 34 starts with TIME = 0.1527141613 DT = 0.00954311462 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.324617027e-29 MLMG: Initial residual (resid0) = 1.324617027e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.244727183e-39, 9.396883457e-11 MLMG: Timers: Solve = 0.005703676 Iter = 0.005497488 Bottom = 0.000123541 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.324617027e-29 MLMG: Initial residual (resid0) = 1.244727183e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00021406 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.49245482e-19 MLMG: Initial residual (resid0) = 5.49245482e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.735142535e-30, 1.772457463e-11 MLMG: Timers: Solve = 0.007235134 Iter = 0.007038791 Bottom = 0.000228515 Done calling nodal solver Timestep 34 ends with TIME = 0.1622572759 DT = 0.00954311462 Timing summary: Advection :0.006494942 seconds MAC Proj :0.00667845 seconds Nodal Proj :0.008049228 seconds Reactions :0.012446432 seconds Misc :0.001516289 seconds Base State :5.09999154e-08 seconds Time to advance time step: 0.035329222 Call to estdt for level 0 gives dt_lev = 1.430870716e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 35 gives dt =1e+20 dt_growth factor limits the new dt = 0.01002027035 Timestep 35 starts with TIME = 0.1622572759 DT = 0.01002027035 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.390880152e-29 MLMG: Initial residual (resid0) = 1.390880152e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.307016301e-39, 9.397044739e-11 MLMG: Timers: Solve = 0.00527672 Iter = 0.005056152 Bottom = 0.000120728 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.390880152e-29 MLMG: Initial residual (resid0) = 1.307016301e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022242 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.681793327e-19 MLMG: Initial residual (resid0) = 5.681793327e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.549561715e-29, 8.007263646e-11 MLMG: Timers: Solve = 0.007284596 Iter = 0.007096271 Bottom = 0.000218515 Done calling nodal solver Timestep 35 ends with TIME = 0.1722775463 DT = 0.01002027035 Timing summary: Advection :0.006509249 seconds MAC Proj :0.006219266 seconds Nodal Proj :0.008150394 seconds Reactions :0.012792001 seconds Misc :0.001515533 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.035361143 Call to estdt for level 0 gives dt_lev = 2.977709039e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 36 gives dt =1e+20 dt_growth factor limits the new dt = 0.01052128387 Timestep 36 starts with TIME = 0.1722775463 DT = 0.01052128387 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 4.305515288e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.232267053e-30, 5.184668742e-11 MLMG: Timers: Solve = 0.005285494 Iter = 0.005072268 Bottom = 0.000122726 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 2.232267053e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000214218 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.055431439e-19 MLMG: Initial residual (resid0) = 6.055431439e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.073306314e-29, 1.772468773e-11 MLMG: Timers: Solve = 0.006899372 Iter = 0.006691985 Bottom = 0.000218178 Done calling nodal solver Timestep 36 ends with TIME = 0.1827988301 DT = 0.01052128387 Timing summary: Advection :0.006471461 seconds MAC Proj :0.006244311 seconds Nodal Proj :0.00770609 seconds Reactions :0.0120588 seconds Misc :0.001505486 seconds Base State :7.300013749e-08 seconds Time to advance time step: 0.03414619 Call to estdt for level 0 gives dt_lev = 1.290240107e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 37 gives dt =1e+20 dt_growth factor limits the new dt = 0.01104734806 Timestep 37 starts with TIME = 0.1827988301 DT = 0.01104734806 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.531602761e-29 MLMG: Initial residual (resid0) = 1.531602761e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.182310547e-39, 7.719433372e-11 MLMG: Timers: Solve = 0.005718811 Iter = 0.005275439 Bottom = 0.000119868 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.531602761e-29 MLMG: Initial residual (resid0) = 1.182310547e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000223313 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.264177143e-19 MLMG: Initial residual (resid0) = 6.264177143e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.855293464e-29, 7.750887871e-11 MLMG: Timers: Solve = 0.007058284 Iter = 0.006853759 Bottom = 0.00023225 Done calling nodal solver Timestep 37 ends with TIME = 0.1938461782 DT = 0.01104734806 Timing summary: Advection :0.006533616 seconds MAC Proj :0.006701443 seconds Nodal Proj :0.007873001 seconds Reactions :0.013047992 seconds Misc :0.001492833 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.035801253 Call to estdt for level 0 gives dt_lev = 2.789553225e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 38 gives dt =1e+20 dt_growth factor limits the new dt = 0.01159971547 Timestep 38 starts with TIME = 0.1938461782 DT = 0.01159971547 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 4.746830605e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.490916131e-30, 5.247535331e-11 MLMG: Timers: Solve = 0.005869036 Iter = 0.005643221 Bottom = 0.000124416 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 2.490916131e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000232637 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.676113162e-19 MLMG: Initial residual (resid0) = 6.676113162e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.183310617e-29, 1.772454403e-11 MLMG: Timers: Solve = 0.007337766 Iter = 0.007136322 Bottom = 0.000234332 Done calling nodal solver Timestep 38 ends with TIME = 0.2054458937 DT = 0.01159971547 Timing summary: Advection :0.006292584 seconds MAC Proj :0.006832335 seconds Nodal Proj :0.008145327 seconds Reactions :0.012230704 seconds Misc :0.001526201 seconds Base State :5.300012162e-08 seconds Time to advance time step: 0.035180639 Call to estdt for level 0 gives dt_lev = 1.16844655e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 39 gives dt =1e+20 dt_growth factor limits the new dt = 0.01217970124 Timestep 39 starts with TIME = 0.2054458937 DT = 0.01217970124 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.536075919e-29 MLMG: Initial residual (resid0) = 1.536075919e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.17936782e-39, 7.677796427e-11 MLMG: Timers: Solve = 0.005258052 Iter = 0.005033995 Bottom = 0.00011972 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.536075919e-29 MLMG: Initial residual (resid0) = 1.17936782e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000214118 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.00991882e-19 MLMG: Initial residual (resid0) = 7.00991882e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.242484815e-29, 1.772466767e-11 MLMG: Timers: Solve = 0.007037728 Iter = 0.006837223 Bottom = 0.000227323 Done calling nodal solver Timestep 39 ends with TIME = 0.2176255949 DT = 0.01217970124 Timing summary: Advection :0.006443536 seconds MAC Proj :0.006221563 seconds Nodal Proj :0.007899602 seconds Reactions :0.01261864 seconds Misc :0.001519967 seconds Base State :4.80001745e-08 seconds Time to advance time step: 0.034879862 Call to estdt for level 0 gives dt_lev = 1.116518296e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 40 gives dt =1e+20 dt_growth factor limits the new dt = 0.0127886863 Timestep 40 starts with TIME = 0.2176255949 DT = 0.0127886863 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.750107688e-29 MLMG: Initial residual (resid0) = 1.750107688e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.667934734e-39, 9.530469151e-11 MLMG: Timers: Solve = 0.005264299 Iter = 0.005052963 Bottom = 0.000122551 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.750107688e-29 MLMG: Initial residual (resid0) = 1.667934734e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000223872 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.360414761e-19 MLMG: Initial residual (resid0) = 7.360414761e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.304605685e-29, 1.772462188e-11 MLMG: Timers: Solve = 0.007149548 Iter = 0.006916658 Bottom = 0.000224753 Done calling nodal solver Timestep 40 ends with TIME = 0.2304142812 DT = 0.0127886863 Timing summary: Advection :0.007116209 seconds MAC Proj :0.006208256 seconds Nodal Proj :0.007958571 seconds Reactions :0.012268015 seconds Misc :0.001562806 seconds Base State :8.300003174e-08 seconds Time to advance time step: 0.035261418 Call to estdt for level 0 gives dt_lev = 1.065046887e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 41 gives dt =1e+20 dt_growth factor limits the new dt = 0.01342812062 Timestep 41 starts with TIME = 0.2304142812 DT = 0.01342812062 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.863121796e-29 MLMG: Initial residual (resid0) = 1.863121796e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.751491358e-39, 9.400841973e-11 MLMG: Timers: Solve = 0.00545715 Iter = 0.00507582 Bottom = 0.00011878 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.863121796e-29 MLMG: Initial residual (resid0) = 1.751491358e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000211783 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.728435499e-19 MLMG: Initial residual (resid0) = 7.728435499e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.369865821e-29, 1.772500814e-11 MLMG: Timers: Solve = 0.007381152 Iter = 0.0071797 Bottom = 0.000235033 Done calling nodal solver Timestep 41 ends with TIME = 0.2438424018 DT = 0.01342812062 Timing summary: Advection :0.007117678 seconds MAC Proj :0.006483883 seconds Nodal Proj :0.008176902 seconds Reactions :0.012866211 seconds Misc :0.001496514 seconds Base State :5.300012162e-08 seconds Time to advance time step: 0.036275631 Call to estdt for level 0 gives dt_lev = 1.015209966e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 42 gives dt =1e+20 dt_growth factor limits the new dt = 0.01409952665 Timestep 42 starts with TIME = 0.2438424018 DT = 0.01409952665 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.957437553e-29 MLMG: Initial residual (resid0) = 1.957437553e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.839212642e-39, 9.396022058e-11 MLMG: Timers: Solve = 0.005735263 Iter = 0.005520005 Bottom = 0.000120044 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.957437553e-29 MLMG: Initial residual (resid0) = 1.839212642e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000227282 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.114857274e-19 MLMG: Initial residual (resid0) = 8.114857274e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.438294112e-29, 1.772420714e-11 MLMG: Timers: Solve = 0.007170877 Iter = 0.006969657 Bottom = 0.000221478 Done calling nodal solver Timestep 42 ends with TIME = 0.2579419285 DT = 0.01409952665 Timing summary: Advection :0.006520252 seconds MAC Proj :0.00675297 seconds Nodal Proj :0.007988417 seconds Reactions :0.011988737 seconds Misc :0.001519754 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.034907788 Call to estdt for level 0 gives dt_lev = 9.673808914e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 43 gives dt =1e+20 dt_growth factor limits the new dt = 0.01480450298 Timestep 43 starts with TIME = 0.2579419285 DT = 0.01480450298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.055305455e-29 MLMG: Initial residual (resid0) = 2.055305455e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.931045336e-39, 9.395417752e-11 MLMG: Timers: Solve = 0.005283382 Iter = 0.005072066 Bottom = 0.000122239 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.055305455e-29 MLMG: Initial residual (resid0) = 1.931045336e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022629 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.520600138e-19 MLMG: Initial residual (resid0) = 8.520600138e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.510256484e-29, 1.772476657e-11 MLMG: Timers: Solve = 0.007199437 Iter = 0.00699924 Bottom = 0.000226156 Done calling nodal solver Timestep 43 ends with TIME = 0.2727464314 DT = 0.01480450298 Timing summary: Advection :0.006584175 seconds MAC Proj :0.006288491 seconds Nodal Proj :0.008020283 seconds Reactions :0.012568136 seconds Misc :0.001592636 seconds Base State :4.80001745e-08 seconds Time to advance time step: 0.035193766 Call to estdt for level 0 gives dt_lev = 9.21627116e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 44 gives dt =1e+20 dt_growth factor limits the new dt = 0.01554472813 Timestep 44 starts with TIME = 0.2727464314 DT = 0.01554472813 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.158165969e-29 MLMG: Initial residual (resid0) = 2.158165969e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.027690088e-39, 9.395431664e-11 MLMG: Timers: Solve = 0.005328756 Iter = 0.005118917 Bottom = 0.000119981 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.158165969e-29 MLMG: Initial residual (resid0) = 2.027690088e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.0002773 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.946630145e-19 MLMG: Initial residual (resid0) = 8.946630145e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.585743309e-29, 1.772447595e-11 MLMG: Timers: Solve = 0.007324248 Iter = 0.007087594 Bottom = 0.000259837 Done calling nodal solver Timestep 44 ends with TIME = 0.2882911596 DT = 0.01554472813 Timing summary: Advection :0.007344495 seconds MAC Proj :0.006384063 seconds Nodal Proj :0.008140326 seconds Reactions :0.013686784 seconds Misc :0.001905026 seconds Base State :5.20001322e-08 seconds Time to advance time step: 0.037614995 Call to estdt for level 0 gives dt_lev = 8.779254781e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 45 gives dt =1e+20 dt_growth factor limits the new dt = 0.01632196453 Timestep 45 starts with TIME = 0.2882911596 DT = 0.01632196453 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.2662186e-29 MLMG: Initial residual (resid0) = 2.2662186e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.128830206e-39, 9.393754894e-11 MLMG: Timers: Solve = 0.005440306 Iter = 0.005182395 Bottom = 0.000148107 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.2662186e-29 MLMG: Initial residual (resid0) = 2.128830206e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000257498 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.053842861e-18 MLMG: Initial residual (resid0) = 1.053842861e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 6.68124357e-29, 6.339885971e-11 MLMG: Timers: Solve = 0.007435907 Iter = 0.007184809 Bottom = 0.000253544 Done calling nodal solver Timestep 45 ends with TIME = 0.3046131241 DT = 0.01632196453 Timing summary: Advection :0.007194122 seconds MAC Proj :0.006469947 seconds Nodal Proj :0.008256565 seconds Reactions :0.013838707 seconds Misc :0.001502252 seconds Base State :5.299989425e-08 seconds Time to advance time step: 0.037397042 Call to estdt for level 0 gives dt_lev = 2.027437947e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 46 gives dt =1e+20 dt_growth factor limits the new dt = 0.01713806276 Timestep 46 starts with TIME = 0.3046131241 DT = 0.01713806276 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 7.013230718e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.387375708e-30, 4.829978999e-11 MLMG: Timers: Solve = 0.005629554 Iter = 0.005302855 Bottom = 0.000144232 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 3.387375708e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000260842 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 9.863659735e-19 MLMG: Initial residual (resid0) = 9.863659735e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.748282166e-29, 1.772447766e-11 MLMG: Timers: Solve = 0.007305433 Iter = 0.0070282 Bottom = 0.000256084 Done calling nodal solver Timestep 46 ends with TIME = 0.3217511869 DT = 0.01713806276 Timing summary: Advection :0.006409735 seconds MAC Proj :0.006679359 seconds Nodal Proj :0.008097009 seconds Reactions :0.013771643 seconds Misc :0.001868264 seconds Base State :5.100014278e-08 seconds Time to advance time step: 0.036965313 Call to estdt for level 0 gives dt_lev = 7.924349732e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 47 gives dt =1e+20 dt_growth factor limits the new dt = 0.0179949659 Timestep 47 starts with TIME = 0.3217511869 DT = 0.0179949659 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.807872089e-29 MLMG: Initial residual (resid0) = 1.807872089e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.373027268e-39, 7.59471467e-11 MLMG: Timers: Solve = 0.005853672 Iter = 0.005511388 Bottom = 0.000141998 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.807872089e-29 MLMG: Initial residual (resid0) = 1.373027268e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000267513 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.035684272e-18 MLMG: Initial residual (resid0) = 1.035684272e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.835709756e-29, 1.772460783e-11 MLMG: Timers: Solve = 0.007210268 Iter = 0.006978753 Bottom = 0.000254433 Done calling nodal solver Timestep 47 ends with TIME = 0.3397461528 DT = 0.0179949659 Timing summary: Advection :0.006577796 seconds MAC Proj :0.006937276 seconds Nodal Proj :0.008012123 seconds Reactions :0.013564559 seconds Misc :0.001520614 seconds Base State :5.399988368e-08 seconds Time to advance time step: 0.03674319 Call to estdt for level 0 gives dt_lev = 7.566055076e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 48 gives dt =1e+20 dt_growth factor limits the new dt = 0.01889471419 Timestep 48 starts with TIME = 0.3397461528 DT = 0.01889471419 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.590316044e-29 MLMG: Initial residual (resid0) = 2.590316044e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.464404755e-39, 9.51391534e-11 MLMG: Timers: Solve = 0.00591858 Iter = 0.005652906 Bottom = 0.000141222 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.590316044e-29 MLMG: Initial residual (resid0) = 2.464404755e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000259584 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.087468486e-18 MLMG: Initial residual (resid0) = 1.087468486e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.927489948e-29, 1.772455913e-11 MLMG: Timers: Solve = 0.007442005 Iter = 0.007152545 Bottom = 0.000245296 Done calling nodal solver Timestep 48 ends with TIME = 0.358640867 DT = 0.01889471419 Timing summary: Advection :0.006631787 seconds MAC Proj :0.006925686 seconds Nodal Proj :0.008242292 seconds Reactions :0.013548753 seconds Misc :0.001497997 seconds Base State :5.000015335e-08 seconds Time to advance time step: 0.036976172 Call to estdt for level 0 gives dt_lev = 7.214097476e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 49 gives dt =1e+20 dt_growth factor limits the new dt = 0.0198394499 Timestep 49 starts with TIME = 0.358640867 DT = 0.0198394499 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.753899991e-29 MLMG: Initial residual (resid0) = 2.753899991e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.587581692e-39, 9.396062678e-11 MLMG: Timers: Solve = 0.005278716 Iter = 0.005064352 Bottom = 0.000121316 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.753899991e-29 MLMG: Initial residual (resid0) = 2.587570482e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000216827 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.086359695e-18 MLMG: Initial residual (resid0) = 1.086359695e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 4.01595875e-29, 3.696711842e-11 MLMG: Timers: Solve = 0.007232013 Iter = 0.007034337 Bottom = 0.000218011 Done calling nodal solver Timestep 49 ends with TIME = 0.3784803169 DT = 0.0198394499 Timing summary: Advection :0.006470421 seconds MAC Proj :0.006236561 seconds Nodal Proj :0.008020281 seconds Reactions :0.01244104 seconds Misc :0.001868742 seconds Base State :5.100014278e-08 seconds Time to advance time step: 0.035176057 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 50 gives dt =1e+20 dt_growth factor limits the new dt = 0.0208314224 Timestep 50 starts with TIME = 0.3784803169 DT = 0.0208314224 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 8.242756114e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.781214371e-30, 4.587318027e-11 MLMG: Timers: Solve = 0.005282258 Iter = 0.005060921 Bottom = 0.000121828 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 3.781214371e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000459749 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.198934006e-18 MLMG: Initial residual (resid0) = 1.198934006e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 2.125061471e-29, 1.772459085e-11 MLMG: Timers: Solve = 0.006966858 Iter = 0.006762074 Bottom = 0.00021412 Done calling nodal solver Timestep 50 ends with TIME = 0.3993117393 DT = 0.0208314224 Timing summary: Advection :0.006590208 seconds MAC Proj :0.006623958 seconds Nodal Proj :0.007758575 seconds Reactions :0.012107446 seconds Misc :0.001531361 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.034755255 Writing plotfile 50 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.018541815 Writing checkpoint 50 Writing checkpoint chk0000050 Total Time: 3.348947355 Unused ParmParse Variables: [TOP]::maestro.v(nvals = 1) :: [1] [TOP]::amr.check_file(nvals = 1) :: [test_stability_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] AMReX (v2024-34-g9e8f8d60eca3) finalized