Initializing AMReX (24.08-4-g4efca7995054)... MPI initialized with 16 MPI processes MPI initialized with thread support level 0 AMReX (24.08-4-g4efca7995054) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = 5peaks_const_grav.dat model file = 5peaks_const_grav.dat reading initial model 1000 points found in the initial model 10 variables found in the initial model WARNING: variable not found: gravity WARNING: variable not found: abar WARNING: variable not found: zbar WARNING: variable not found: gpot WARNING: variable not found: cno model file mapping, level: 0 dr of MAESTRO base state = 93750000.000000 dr of input file data = 10010010.010010 maximum radius (cell-centered) of input model = 10000000000.000000 WARNING: resolution of base state array is not an integer multiple of the initial model's resolution. make sure this is a desired property as this could lead to aliasing when performing the interpolation. modulus = 3659909.909910 setting r_cutoff to 105 radius at r_cutoff 9890625000 Maximum HSE Error = 0.054171 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile test_stability_pltInitData after InitData inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.024332105 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.000465656 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile test_stability_pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.022303285 Call to firstdt for level 0 gives dt_lev = 0.01907406555 Multiplying dt_lev by init_shrink; dt_lev = 0.001907406555 Minimum firstdt over all levels = 0.001907406555 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 4.945354899e-27 MLMG: Initial residual (resid0) = 4.945354899e-27 MLMG: Final Iter. 3 resid, resid/bnorm = 2.357566962e-30, 0.0004767235133 MLMG: Timers: Solve = 0.003598344 Iter = 0.003247253 Bottom = 8.2311e-05 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 1 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #2 Calling nodal solver MLMG: Initial rhs = 2.306075226e-30 MLMG: Initial residual (resid0) = 2.306075226e-30 MLMG: Final Iter. 5 resid, resid/bnorm = 1.933642558e-37, 8.384993415e-08 MLMG: Timers: Solve = 0.005355315 Iter = 0.005036728 Bottom = 0.000123662 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 2 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #3 Calling nodal solver MLMG: Initial rhs = 9.742172194e-32 MLMG: Initial residual (resid0) = 9.742172194e-32 MLMG: Final Iter. 4 resid, resid/bnorm = 7.56277059e-41, 7.76292026e-10 MLMG: Timers: Solve = 0.004331447 Iter = 0.004027376 Bottom = 0.00010346 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 3 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Writing plotfile test_stability_pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.038149344 Doing initial pressure iteration #1  Timestep 0 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.893547601e-20 MLMG: Initial residual (resid0) = 4.893547601e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 4.517319639e-31, 9.231175431e-12 MLMG: Timers: Solve = 0.007023003 Iter = 0.006691035 Bottom = 0.00012382 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.893547507e-20 MLMG: Initial residual (resid0) = 2.477484298e-27 MLMG: Final Iter. 4 resid, resid/bnorm = 4.813594317e-30, 9.836615074e-11 MLMG: Timers: Solve = 0.003059109 Iter = 0.002688517 Bottom = 5.4317e-05 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.755411273e-17 MLMG: Initial residual (resid0) = 5.755411273e-17 MLMG: Final Iter. 9 resid, resid/bnorm = 1.020114247e-27, 1.772443703e-11 MLMG: Timers: Solve = 0.024410931 Iter = 0.024118087 Bottom = 0.000232684 Done calling nodal solver Timestep 0 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.009739342 seconds MAC Proj :0.011125866 seconds Nodal Proj :0.030307 seconds Reactions :0.024330528 seconds Misc :0.002165593 seconds Base State :4.800000397e-08 seconds Time to advance time step: 0.099665788 Writing plotfile 0 after all initialization inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.027241036 Writing checkpoint 0 after all initialization Writing checkpoint chk0000000 Beginning main evolution  Timestep 1 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.257776132e-26 MLMG: Initial residual (resid0) = 1.257776132e-26 MLMG: Final Iter. 10 resid, resid/bnorm = 1.092354528e-37, 8.684808849e-12 MLMG: Timers: Solve = 0.00709422 Iter = 0.006688779 Bottom = 0.000125539 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.257776132e-26 MLMG: Initial residual (resid0) = 1.092354528e-37 MLMG: No iterations needed MLMG: Timers: Solve = 0.000372386 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.097790919e-19 MLMG: Initial residual (resid0) = 1.097790919e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.945791097e-30, 1.772460551e-11 MLMG: Timers: Solve = 0.008734483 Iter = 0.008411501 Bottom = 0.000218913 Done calling nodal solver Timestep 1 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.013376558 seconds MAC Proj :0.008503565 seconds Nodal Proj :0.009861192 seconds Reactions :0.024401795 seconds Misc :0.003168177 seconds Base State :4.700001455e-08 seconds Time to advance time step: 0.066032208 Call to estdt for level 0 gives dt_lev = 7.191087425e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 2 gives dt =1e+20 dt_growth factor limits the new dt = 0.002002776883  Timestep 2 starts with TIME = 0.001907406555 DT = 0.002002776883 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.08039884e-27 MLMG: Initial residual (resid0) = 8.08039884e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 1.160384542e-37, 1.436048597e-11 MLMG: Timers: Solve = 0.011502419 Iter = 0.011148069 Bottom = 0.000125107 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.498306041e-27 MLMG: Initial residual (resid0) = 2.601349809e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 8.687490856e-37, 9.146358118e-11 MLMG: Timers: Solve = 0.005652957 Iter = 0.005420741 Bottom = 0.000123392 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.096671578e-19 MLMG: Initial residual (resid0) = 1.096671578e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.008841827e-29, 9.199124398e-11 MLMG: Timers: Solve = 0.007411262 Iter = 0.007191686 Bottom = 0.000226626 Done calling nodal solver Timestep 2 ends with TIME = 0.003910183437 DT = 0.002002776883 Timing summary: Advection :0.007700615 seconds MAC Proj :0.018266134 seconds Nodal Proj :0.008276533 seconds Reactions :0.021173856 seconds Misc :0.001484313 seconds Base State :8.499998216e-08 seconds Time to advance time step: 0.057110304 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 3 gives dt =1e+20 dt_growth factor limits the new dt = 0.002102915727  Timestep 3 starts with TIME = 0.003910183437 DT = 0.002102915727 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 8.320997544e-21 MLMG: Final Iter. 10 resid, resid/bnorm = 7.677524121e-31, 9.226687161e-11 MLMG: Timers: Solve = 0.010531234 Iter = 0.010297149 Bottom = 0.000123745 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 7.677524121e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000230528 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.21031446e-19 MLMG: Initial residual (resid0) = 1.21031446e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.145245217e-30, 1.772469294e-11 MLMG: Timers: Solve = 0.007365167 Iter = 0.007150357 Bottom = 0.000216622 Done calling nodal solver Timestep 3 ends with TIME = 0.006013099164 DT = 0.002102915727 Timing summary: Advection :0.006625125 seconds MAC Proj :0.011591149 seconds Nodal Proj :0.008250461 seconds Reactions :0.013201093 seconds Misc :0.001546227 seconds Base State :9.300001125e-08 seconds Time to advance time step: 0.041418293 Call to estdt for level 0 gives dt_lev = 6.528670715e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 4 gives dt =1e+20 dt_growth factor limits the new dt = 0.002208061513  Timestep 4 starts with TIME = 0.006013099164 DT = 0.002208061513 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.3079729e-29 MLMG: Initial residual (resid0) = 1.3079729e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.129684783e-39, 8.63691276e-11 MLMG: Timers: Solve = 0.006803184 Iter = 0.0063173 Bottom = 0.000125143 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.3079729e-29 MLMG: Initial residual (resid0) = 1.129684783e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000465576 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.270830183e-19 MLMG: Initial residual (resid0) = 1.270830183e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.252519515e-30, 1.772478766e-11 MLMG: Timers: Solve = 0.00771877 Iter = 0.007434865 Bottom = 0.000218511 Done calling nodal solver Timestep 4 ends with TIME = 0.008221160677 DT = 0.002208061513 Timing summary: Advection :0.008836227 seconds MAC Proj :0.008308269 seconds Nodal Proj :0.008720962 seconds Reactions :0.0236447 seconds Misc :0.002141958 seconds Base State :8.799997886e-08 seconds Time to advance time step: 0.051870443 Call to estdt for level 0 gives dt_lev = 6.226377027e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 5 gives dt =1e+20 dt_growth factor limits the new dt = 0.002318464589  Timestep 5 starts with TIME = 0.008221160677 DT = 0.002318464589 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.295423824e-30 MLMG: Initial residual (resid0) = 3.295423824e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.024461011e-40, 9.177760352e-11 MLMG: Timers: Solve = 0.006376327 Iter = 0.005873452 Bottom = 0.000123508 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.295423824e-30 MLMG: Initial residual (resid0) = 3.024461011e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00049056 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.334371692e-19 MLMG: Initial residual (resid0) = 1.334371692e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.365126231e-30, 1.772464333e-11 MLMG: Timers: Solve = 0.008624247 Iter = 0.008209837 Bottom = 0.000219299 Done calling nodal solver Timestep 5 ends with TIME = 0.01053962527 DT = 0.002318464589 Timing summary: Advection :0.009540458 seconds MAC Proj :0.008042295 seconds Nodal Proj :0.009926953 seconds Reactions :0.024604482 seconds Misc :0.002222199 seconds Base State :9.299998283e-08 seconds Time to advance time step: 0.054555568 Call to estdt for level 0 gives dt_lev = 5.914991835e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 6 gives dt =1e+20 dt_growth factor limits the new dt = 0.002434387818  Timestep 6 starts with TIME = 0.01053962527 DT = 0.002434387818 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.377300377e-30 MLMG: Initial residual (resid0) = 3.377300377e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.175447418e-40, 9.402324529e-11 MLMG: Timers: Solve = 0.007086155 Iter = 0.006600247 Bottom = 0.000125104 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.377300377e-30 MLMG: Initial residual (resid0) = 3.175443914e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00055045 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.401090277e-19 MLMG: Initial residual (resid0) = 1.401090277e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.483390367e-30, 1.772469917e-11 MLMG: Timers: Solve = 0.007009677 Iter = 0.006786841 Bottom = 0.000219326 Done calling nodal solver Timestep 6 ends with TIME = 0.01297401308 DT = 0.002434387818 Timing summary: Advection :0.009600079 seconds MAC Proj :0.008814665 seconds Nodal Proj :0.007844474 seconds Reactions :0.02270356 seconds Misc :0.002250843 seconds Base State :7.500000265e-08 seconds Time to advance time step: 0.051406429 Call to estdt for level 0 gives dt_lev = 5.625582499e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 7 gives dt =1e+20 dt_growth factor limits the new dt = 0.002556107209  Timestep 7 starts with TIME = 0.01297401308 DT = 0.002556107209 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.542867857e-30 MLMG: Initial residual (resid0) = 3.542867857e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.33382217e-40, 9.409953474e-11 MLMG: Timers: Solve = 0.005508453 Iter = 0.005231592 Bottom = 0.000142607 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.542867857e-30 MLMG: Initial residual (resid0) = 3.33382217e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000276153 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.471144791e-19 MLMG: Initial residual (resid0) = 1.471144791e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.607576737e-30, 1.772481372e-11 MLMG: Timers: Solve = 0.007331536 Iter = 0.007109423 Bottom = 0.000256053 Done calling nodal solver Timestep 7 ends with TIME = 0.01553012029 DT = 0.002556107209 Timing summary: Advection :0.006528927 seconds MAC Proj :0.006572808 seconds Nodal Proj :0.008132829 seconds Reactions :0.013564527 seconds Misc :0.001412248 seconds Base State :2.799999947e-07 seconds Time to advance time step: 0.036374039 Call to estdt for level 0 gives dt_lev = 5.353302437e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 8 gives dt =1e+20 dt_growth factor limits the new dt = 0.002683912569  Timestep 8 starts with TIME = 0.01553012029 DT = 0.002683912569 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.719890133e-30 MLMG: Initial residual (resid0) = 3.719890133e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.500289421e-40, 9.409658071e-11 MLMG: Timers: Solve = 0.005313222 Iter = 0.005091342 Bottom = 0.000124669 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.719890133e-30 MLMG: Initial residual (resid0) = 3.500289421e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000226034 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.54470203e-19 MLMG: Initial residual (resid0) = 1.54470203e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.737926083e-30, 1.77246228e-11 MLMG: Timers: Solve = 0.006978132 Iter = 0.006770282 Bottom = 0.000217883 Done calling nodal solver Timestep 8 ends with TIME = 0.01821403286 DT = 0.002683912569 Timing summary: Advection :0.006325613 seconds MAC Proj :0.006258753 seconds Nodal Proj :0.007778039 seconds Reactions :0.013101756 seconds Misc :0.001343649 seconds Base State :8.800000728e-08 seconds Time to advance time step: 0.034967172 Call to estdt for level 0 gives dt_lev = 5.095587997e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 9 gives dt =1e+20 dt_growth factor limits the new dt = 0.002818108198  Timestep 9 starts with TIME = 0.01821403286 DT = 0.002818108198 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.905661102e-30 MLMG: Initial residual (resid0) = 3.905661102e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.676397606e-40, 9.412996953e-11 MLMG: Timers: Solve = 0.005294908 Iter = 0.005060414 Bottom = 0.000124097 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.905661102e-30 MLMG: Initial residual (resid0) = 3.676397606e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000231435 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.621937132e-19 MLMG: Initial residual (resid0) = 1.621937132e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.874823591e-30, 1.772463022e-11 MLMG: Timers: Solve = 0.008022443 Iter = 0.007820936 Bottom = 0.000212469 Done calling nodal solver Timestep 9 ends with TIME = 0.02103214106 DT = 0.002818108198 Timing summary: Advection :0.006326072 seconds MAC Proj :0.006264391 seconds Nodal Proj :0.008877181 seconds Reactions :0.013554578 seconds Misc :0.001324517 seconds Base State :8.300000331e-08 seconds Time to advance time step: 0.0365207 Call to estdt for level 0 gives dt_lev = 4.851262359e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 10 gives dt =1e+20 dt_growth factor limits the new dt = 0.002959013608  Timestep 10 starts with TIME = 0.02103214106 DT = 0.002959013608 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.100939546e-30 MLMG: Initial residual (resid0) = 4.100939546e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.860100828e-40, 9.412723071e-11 MLMG: Timers: Solve = 0.005323664 Iter = 0.005090237 Bottom = 0.000122924 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.100939546e-30 MLMG: Initial residual (resid0) = 3.860100828e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000232109 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.703033988e-19 MLMG: Initial residual (resid0) = 1.703033988e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.174813655e-29, 6.898357067e-11 MLMG: Timers: Solve = 0.006960787 Iter = 0.006767641 Bottom = 0.000215797 Done calling nodal solver Timestep 10 ends with TIME = 0.02399115467 DT = 0.002959013608 Timing summary: Advection :0.006337008 seconds MAC Proj :0.006328303 seconds Nodal Proj :0.007784225 seconds Reactions :0.013787571 seconds Misc :0.001310989 seconds Base State :5.999999075e-08 seconds Time to advance time step: 0.035699569 Call to estdt for level 0 gives dt_lev = 1.153494089e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 11 gives dt =1e+20 dt_growth factor limits the new dt = 0.003106964288  Timestep 11 starts with TIME = 0.02399115467 DT = 0.003106964288 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 1.271430598e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.310351499e-31, 4.963189897e-11 MLMG: Timers: Solve = 0.005247179 Iter = 0.005019074 Bottom = 0.000130764 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 6.310351499e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000227135 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.788185688e-19 MLMG: Initial residual (resid0) = 1.788185688e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.169478835e-30, 1.772455096e-11 MLMG: Timers: Solve = 0.007047327 Iter = 0.006841991 Bottom = 0.000210992 Done calling nodal solver Timestep 11 ends with TIME = 0.02709811896 DT = 0.003106964288 Timing summary: Advection :0.006169604 seconds MAC Proj :0.006270797 seconds Nodal Proj :0.00786266 seconds Reactions :0.013933299 seconds Misc :0.001297029 seconds Base State :1.690000033e-07 seconds Time to advance time step: 0.03569798 Call to estdt for level 0 gives dt_lev = 4.376646045e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 12 gives dt =1e+20 dt_growth factor limits the new dt = 0.003262312503  Timestep 12 starts with TIME = 0.02709811896 DT = 0.003262312503 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.931087603e-30 MLMG: Initial residual (resid0) = 2.931087603e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.211756947e-40, 7.545857536e-11 MLMG: Timers: Solve = 0.005275815 Iter = 0.005051231 Bottom = 0.000120244 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.931087603e-30 MLMG: Initial residual (resid0) = 2.211756947e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000223486 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.877594972e-19 MLMG: Initial residual (resid0) = 1.877594972e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.327886573e-30, 1.772419836e-11 MLMG: Timers: Solve = 0.006913774 Iter = 0.006689272 Bottom = 0.000210908 Done calling nodal solver Timestep 12 ends with TIME = 0.03036043146 DT = 0.003262312503 Timing summary: Advection :0.006309666 seconds MAC Proj :0.006307077 seconds Nodal Proj :0.007730349 seconds Reactions :0.013826093 seconds Misc :0.001338654 seconds Base State :8.499998216e-08 seconds Time to advance time step: 0.035689958 Call to estdt for level 0 gives dt_lev = 4.177453783e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 13 gives dt =1e+20 dt_growth factor limits the new dt = 0.003425428128  Timestep 13 starts with TIME = 0.03036043146 DT = 0.003425428128 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.688248856e-30 MLMG: Initial residual (resid0) = 4.688248856e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.467598744e-40, 9.52935495e-11 MLMG: Timers: Solve = 0.005273912 Iter = 0.005047989 Bottom = 0.000121135 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.688248856e-30 MLMG: Initial residual (resid0) = 4.467598744e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000222133 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.971474721e-19 MLMG: Initial residual (resid0) = 1.971474721e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.494310995e-30, 1.7724351e-11 MLMG: Timers: Solve = 0.006820817 Iter = 0.006611159 Bottom = 0.000211107 Done calling nodal solver Timestep 13 ends with TIME = 0.03378585959 DT = 0.003425428128 Timing summary: Advection :0.006363276 seconds MAC Proj :0.006265616 seconds Nodal Proj :0.007639307 seconds Reactions :0.012126077 seconds Misc :0.001377933 seconds Base State :9.800001521e-08 seconds Time to advance time step: 0.033931148 Call to estdt for level 0 gives dt_lev = 3.982247017e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 14 gives dt =1e+20 dt_growth factor limits the new dt = 0.003596699534  Timestep 14 starts with TIME = 0.03378585959 DT = 0.003596699534 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.98227213e-30 MLMG: Initial residual (resid0) = 4.98227213e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.691855544e-40, 9.417100114e-11 MLMG: Timers: Solve = 0.005268103 Iter = 0.005048015 Bottom = 0.000121067 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.98227213e-30 MLMG: Initial residual (resid0) = 4.691855544e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000233964 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.221658729e-19 MLMG: Initial residual (resid0) = 2.221658729e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.863225901e-30, 3.989463271e-11 MLMG: Timers: Solve = 0.006892981 Iter = 0.006681344 Bottom = 0.000221001 Done calling nodal solver Timestep 14 ends with TIME = 0.03738255912 DT = 0.003596699534 Timing summary: Advection :0.006456959 seconds MAC Proj :0.006267828 seconds Nodal Proj :0.007769019 seconds Reactions :0.012330724 seconds Misc :0.001353599 seconds Base State :7.299999538e-08 seconds Time to advance time step: 0.034328011 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 15 gives dt =1e+20 dt_growth factor limits the new dt = 0.003776534511  Timestep 15 starts with TIME = 0.03738255912 DT = 0.003776534511 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 1.44706648e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 8.546351457e-31, 5.905983986e-11 MLMG: Timers: Solve = 0.005272573 Iter = 0.005046744 Bottom = 0.000120749 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 8.546351457e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022687 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.279163939e-19 MLMG: Initial residual (resid0) = 2.279163939e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.500913317e-29, 6.585367956e-11 MLMG: Timers: Solve = 0.006957649 Iter = 0.006740148 Bottom = 0.000215298 Done calling nodal solver Timestep 15 ends with TIME = 0.04115909363 DT = 0.003776534511 Timing summary: Advection :0.006203461 seconds MAC Proj :0.006300504 seconds Nodal Proj :0.007810189 seconds Reactions :0.012201202 seconds Misc :0.001337486 seconds Base State :9.000001455e-08 seconds Time to advance time step: 0.034012662 Call to estdt for level 0 gives dt_lev = 9.044183602e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 16 gives dt =1e+20 dt_growth factor limits the new dt = 0.003965361236  Timestep 16 starts with TIME = 0.04115909363 DT = 0.003965361236 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 1.62270343e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.18605137e-31, 3.812188509e-11 MLMG: Timers: Solve = 0.005258798 Iter = 0.005039926 Bottom = 0.000120632 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 6.18605137e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000216095 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.282228424e-19 MLMG: Initial residual (resid0) = 2.282228424e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.045223255e-30, 1.772488333e-11 MLMG: Timers: Solve = 0.007237429 Iter = 0.007029743 Bottom = 0.000215782 Done calling nodal solver Timestep 16 ends with TIME = 0.04512445487 DT = 0.003965361236 Timing summary: Advection :0.006073186 seconds MAC Proj :0.006245398 seconds Nodal Proj :0.008084704 seconds Reactions :0.012250762 seconds Misc :0.0012917 seconds Base State :7.100001653e-08 seconds Time to advance time step: 0.034134254 Call to estdt for level 0 gives dt_lev = 3.436635199e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 17 gives dt =1e+20 dt_growth factor limits the new dt = 0.004163629298  Timestep 17 starts with TIME = 0.04512445487 DT = 0.004163629298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.754712132e-30 MLMG: Initial residual (resid0) = 3.754712132e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.82584447e-40, 7.526128158e-11 MLMG: Timers: Solve = 0.005254886 Iter = 0.005038936 Bottom = 0.000118453 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.754712132e-30 MLMG: Initial residual (resid0) = 2.82584447e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00024085 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.396339845e-19 MLMG: Initial residual (resid0) = 2.396339845e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.247421825e-30, 1.772462213e-11 MLMG: Timers: Solve = 0.006910637 Iter = 0.006688151 Bottom = 0.000213321 Done calling nodal solver Timestep 17 ends with TIME = 0.04928808417 DT = 0.004163629298 Timing summary: Advection :0.006270692 seconds MAC Proj :0.006257165 seconds Nodal Proj :0.007742499 seconds Reactions :0.012243716 seconds Misc :0.001322523 seconds Base State :9.400000067e-08 seconds Time to advance time step: 0.033994511 Call to estdt for level 0 gives dt_lev = 3.276873657e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 18 gives dt =1e+20 dt_growth factor limits the new dt = 0.004371810763  Timestep 18 starts with TIME = 0.04928808417 DT = 0.004371810763 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.988437125e-30 MLMG: Initial residual (resid0) = 5.988437125e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.701673257e-40, 9.521137381e-11 MLMG: Timers: Solve = 0.005246808 Iter = 0.005028638 Bottom = 0.000121493 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.988437125e-30 MLMG: Initial residual (resid0) = 5.701673257e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000219947 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.516156837e-19 MLMG: Initial residual (resid0) = 2.516156837e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.459779676e-30, 1.772456951e-11 MLMG: Timers: Solve = 0.006982636 Iter = 0.006766973 Bottom = 0.000213257 Done calling nodal solver Timestep 18 ends with TIME = 0.05365989493 DT = 0.004371810763 Timing summary: Advection :0.006365651 seconds MAC Proj :0.006244961 seconds Nodal Proj :0.007830397 seconds Reactions :0.012226635 seconds Misc :0.001367605 seconds Base State :1.740000073e-07 seconds Time to advance time step: 0.034180257 Call to estdt for level 0 gives dt_lev = 3.122293372e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 19 gives dt =1e+20 dt_growth factor limits the new dt = 0.004590401301  Timestep 19 starts with TIME = 0.05365989493 DT = 0.004590401301 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.361637466e-30 MLMG: Initial residual (resid0) = 6.361637466e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.987748338e-40, 9.41227533e-11 MLMG: Timers: Solve = 0.005244425 Iter = 0.005025948 Bottom = 0.000120223 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.361637466e-30 MLMG: Initial residual (resid0) = 5.987748338e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000221212 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.641964679e-19 MLMG: Initial residual (resid0) = 2.641964679e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.68289866e-30, 1.772506157e-11 MLMG: Timers: Solve = 0.00694168 Iter = 0.006711184 Bottom = 0.000212606 Done calling nodal solver Timestep 19 ends with TIME = 0.05825029623 DT = 0.004590401301 Timing summary: Advection :0.006338266 seconds MAC Proj :0.00622767 seconds Nodal Proj :0.007757633 seconds Reactions :0.012263776 seconds Misc :0.001377487 seconds Base State :7.799999935e-08 seconds Time to advance time step: 0.034114405 Call to estdt for level 0 gives dt_lev = 2.974235616e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 20 gives dt =1e+20 dt_growth factor limits the new dt = 0.004819921366  Timestep 20 starts with TIME = 0.05825029623 DT = 0.004819921366 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.682786498e-30 MLMG: Initial residual (resid0) = 6.682786498e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.287114735e-40, 9.407923982e-11 MLMG: Timers: Solve = 0.005273327 Iter = 0.005058473 Bottom = 0.000123684 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.682786498e-30 MLMG: Initial residual (resid0) = 6.287114735e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000230144 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.774062913e-19 MLMG: Initial residual (resid0) = 2.774062913e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.916875074e-30, 1.772445409e-11 MLMG: Timers: Solve = 0.00687614 Iter = 0.006677215 Bottom = 0.000220924 Done calling nodal solver Timestep 20 ends with TIME = 0.0630702176 DT = 0.004819921366 Timing summary: Advection :0.006404425 seconds MAC Proj :0.006280429 seconds Nodal Proj :0.007695027 seconds Reactions :0.012337133 seconds Misc :0.001374322 seconds Base State :8.900002513e-08 seconds Time to advance time step: 0.034250721 Call to estdt for level 0 gives dt_lev = 2.832901245e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 21 gives dt =1e+20 dt_growth factor limits the new dt = 0.005060917435  Timestep 21 starts with TIME = 0.0630702176 DT = 0.005060917435 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.017767486e-30 MLMG: Initial residual (resid0) = 7.017767486e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.601040624e-40, 9.406183144e-11 MLMG: Timers: Solve = 0.005438882 Iter = 0.005170097 Bottom = 0.000136266 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.017767486e-30 MLMG: Initial residual (resid0) = 6.601040624e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000218752 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.869691725e-19 MLMG: Initial residual (resid0) = 2.869691725e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.297839054e-29, 8.007267937e-11 MLMG: Timers: Solve = 0.007213956 Iter = 0.006988608 Bottom = 0.000215493 Done calling nodal solver Timestep 21 ends with TIME = 0.06813113503 DT = 0.005060917435 Timing summary: Advection :0.006412269 seconds MAC Proj :0.006436971 seconds Nodal Proj :0.008040813 seconds Reactions :0.012420937 seconds Misc :0.001357643 seconds Base State :9.19999934e-08 seconds Time to advance time step: 0.034822768 Call to estdt for level 0 gives dt_lev = 5.895649157e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 22 gives dt =1e+20 dt_growth factor limits the new dt = 0.005313963306  Timestep 22 starts with TIME = 0.06813113503 DT = 0.005313963306 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 2.174577793e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 1.127453232e-30, 5.184699467e-11 MLMG: Timers: Solve = 0.005280389 Iter = 0.005060243 Bottom = 0.000121976 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 1.127453232e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000223615 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.058404362e-19 MLMG: Initial residual (resid0) = 3.058404362e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.420842792e-30, 1.772441493e-11 MLMG: Timers: Solve = 0.006912662 Iter = 0.006704001 Bottom = 0.000218303 Done calling nodal solver Timestep 22 ends with TIME = 0.07344509834 DT = 0.005313963306 Timing summary: Advection :0.006013567 seconds MAC Proj :0.006240564 seconds Nodal Proj :0.007708853 seconds Reactions :0.012420137 seconds Misc :0.001332501 seconds Base State :8.600000001e-08 seconds Time to advance time step: 0.033861543 Call to estdt for level 0 gives dt_lev = 2.554660013e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 23 gives dt =1e+20 dt_growth factor limits the new dt = 0.005579661472  Timestep 23 starts with TIME = 0.07344509834 DT = 0.005579661472 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.73348257e-30 MLMG: Initial residual (resid0) = 7.73348257e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.972845529e-40, 7.723358105e-11 MLMG: Timers: Solve = 0.005266631 Iter = 0.005048805 Bottom = 0.000121328 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.73348257e-30 MLMG: Initial residual (resid0) = 5.972845529e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00023239 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.21132458e-19 MLMG: Initial residual (resid0) = 3.21132458e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.691941506e-30, 1.77245911e-11 MLMG: Timers: Solve = 0.00736705 Iter = 0.007158309 Bottom = 0.000220408 Done calling nodal solver Timestep 23 ends with TIME = 0.07902475981 DT = 0.005579661472 Timing summary: Advection :0.006222133 seconds MAC Proj :0.006275596 seconds Nodal Proj :0.008170448 seconds Reactions :0.012431712 seconds Misc :0.00134216 seconds Base State :9.599997952e-08 seconds Time to advance time step: 0.034617882 Call to estdt for level 0 gives dt_lev = 2.439862005e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 24 gives dt =1e+20 dt_growth factor limits the new dt = 0.005858644545  Timestep 24 starts with TIME = 0.07902475981 DT = 0.005858644545 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.00564811e-30 MLMG: Initial residual (resid0) = 8.00564811e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 7.641742954e-40, 9.545439482e-11 MLMG: Timers: Solve = 0.005348979 Iter = 0.005124931 Bottom = 0.000120896 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.00564811e-30 MLMG: Initial residual (resid0) = 7.641742954e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000242733 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.371890809e-19 MLMG: Initial residual (resid0) = 3.371890809e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.976593952e-30, 1.772475531e-11 MLMG: Timers: Solve = 0.006838532 Iter = 0.00664321 Bottom = 0.000208662 Done calling nodal solver Timestep 24 ends with TIME = 0.08488340435 DT = 0.005858644545 Timing summary: Advection :0.006559578 seconds MAC Proj :0.006375566 seconds Nodal Proj :0.007611196 seconds Reactions :0.012724547 seconds Misc :0.001325092 seconds Base State :7.200000596e-08 seconds Time to advance time step: 0.034770473 Call to estdt for level 0 gives dt_lev = 2.326582163e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 25 gives dt =1e+20 dt_growth factor limits the new dt = 0.006151576773  Timestep 25 starts with TIME = 0.08488340435 DT = 0.006151576773 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.527771313e-30 MLMG: Initial residual (resid0) = 8.527771313e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.024857955e-40, 9.410264019e-11 MLMG: Timers: Solve = 0.005310141 Iter = 0.005083464 Bottom = 0.000122709 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.527771313e-30 MLMG: Initial residual (resid0) = 8.024857955e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000218779 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.540485349e-19 MLMG: Initial residual (resid0) = 3.540485349e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.275353834e-30, 1.772455812e-11 MLMG: Timers: Solve = 0.00704034 Iter = 0.006815242 Bottom = 0.000221742 Done calling nodal solver Timestep 25 ends with TIME = 0.09103498113 DT = 0.006151576773 Timing summary: Advection :0.006505925 seconds MAC Proj :0.006283286 seconds Nodal Proj :0.007866963 seconds Reactions :0.012575004 seconds Misc :0.001337938 seconds Base State :7.799999935e-08 seconds Time to advance time step: 0.034753332 Call to estdt for level 0 gives dt_lev = 2.21729507e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 26 gives dt =1e+20 dt_growth factor limits the new dt = 0.006459155611  Timestep 26 starts with TIME = 0.09103498113 DT = 0.006459155611 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.960012316e-30 MLMG: Initial residual (resid0) = 8.960012316e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.424844588e-40, 9.402715411e-11 MLMG: Timers: Solve = 0.005248288 Iter = 0.005018965 Bottom = 0.000120885 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.960012316e-30 MLMG: Initial residual (resid0) = 8.424844588e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00027394 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.717509617e-19 MLMG: Initial residual (resid0) = 3.717509617e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.58913597e-30, 1.772459698e-11 MLMG: Timers: Solve = 0.006896856 Iter = 0.006692517 Bottom = 0.000211422 Done calling nodal solver Timestep 26 ends with TIME = 0.09749413674 DT = 0.006459155611 Timing summary: Advection :0.006463973 seconds MAC Proj :0.006268319 seconds Nodal Proj :0.007717446 seconds Reactions :0.012279822 seconds Misc :0.00136238 seconds Base State :8.999998613e-08 seconds Time to advance time step: 0.034264071 Call to estdt for level 0 gives dt_lev = 2.112511375e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 27 gives dt =1e+20 dt_growth factor limits the new dt = 0.006782113392  Timestep 27 starts with TIME = 0.09749413674 DT = 0.006782113392 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.408830982e-30 MLMG: Initial residual (resid0) = 9.408830982e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.846691478e-40, 9.402540544e-11 MLMG: Timers: Solve = 0.005261051 Iter = 0.005040516 Bottom = 0.000120122 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.408830982e-30 MLMG: Initial residual (resid0) = 8.846691478e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022649 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.903385097e-19 MLMG: Initial residual (resid0) = 3.903385097e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.918614436e-30, 1.772465248e-11 MLMG: Timers: Solve = 0.006897425 Iter = 0.006687826 Bottom = 0.000223274 Done calling nodal solver Timestep 27 ends with TIME = 0.1042762501 DT = 0.006782113392 Timing summary: Advection :0.006506835 seconds MAC Proj :0.006231344 seconds Nodal Proj :0.007719143 seconds Reactions :0.012332179 seconds Misc :0.001382556 seconds Base State :4.300000001e-08 seconds Time to advance time step: 0.034321317 Call to estdt for level 0 gives dt_lev = 2.0124204e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 28 gives dt =1e+20 dt_growth factor limits the new dt = 0.007121219061  Timestep 28 starts with TIME = 0.1042762501 DT = 0.007121219061 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.880130395e-30 MLMG: Initial residual (resid0) = 9.880130395e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 9.288520884e-40, 9.40121285e-11 MLMG: Timers: Solve = 0.005251081 Iter = 0.005024295 Bottom = 0.000119772 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.880130395e-30 MLMG: Initial residual (resid0) = 9.288520884e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000218238 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.098554352e-19 MLMG: Initial residual (resid0) = 4.098554352e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.264511454e-30, 1.772457025e-11 MLMG: Timers: Solve = 0.006933858 Iter = 0.006687042 Bottom = 0.000211863 Done calling nodal solver Timestep 28 ends with TIME = 0.1113974692 DT = 0.007121219061 Timing summary: Advection :0.006391999 seconds MAC Proj :0.006242833 seconds Nodal Proj :0.007745729 seconds Reactions :0.01237118 seconds Misc :0.001344439 seconds Base State :8.800000728e-08 seconds Time to advance time step: 0.034266436 Call to estdt for level 0 gives dt_lev = 1.916904797e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 29 gives dt =1e+20 dt_growth factor limits the new dt = 0.007477280014  Timestep 29 starts with TIME = 0.1113974692 DT = 0.007477280014 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.037425901e-29 MLMG: Initial residual (resid0) = 1.037425901e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 9.752925208e-40, 9.401081271e-11 MLMG: Timers: Solve = 0.005255465 Iter = 0.005040521 Bottom = 0.000119222 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.037425901e-29 MLMG: Initial residual (resid0) = 9.752925208e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000224895 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.30348207e-19 MLMG: Initial residual (resid0) = 4.30348207e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.627838138e-30, 1.77248052e-11 MLMG: Timers: Solve = 0.006997822 Iter = 0.006787695 Bottom = 0.000216225 Done calling nodal solver Timestep 29 ends with TIME = 0.1188747492 DT = 0.007477280014 Timing summary: Advection :0.006406135 seconds MAC Proj :0.006268206 seconds Nodal Proj :0.007853547 seconds Reactions :0.012240947 seconds Misc :0.001312824 seconds Base State :2.879999954e-07 seconds Time to advance time step: 0.034251426 Call to estdt for level 0 gives dt_lev = 1.825812456e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 30 gives dt =1e+20 dt_growth factor limits the new dt = 0.007851144015  Timestep 30 starts with TIME = 0.1188747492 DT = 0.007851144015 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.08944873e-29 MLMG: Initial residual (resid0) = 1.08944873e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.023977833e-39, 9.399045635e-11 MLMG: Timers: Solve = 0.005258765 Iter = 0.005029444 Bottom = 0.000121805 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.08944873e-29 MLMG: Initial residual (resid0) = 1.023977833e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000262216 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.518656173e-19 MLMG: Initial residual (resid0) = 4.518656173e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.00907597e-30, 1.772446423e-11 MLMG: Timers: Solve = 0.006873035 Iter = 0.006655332 Bottom = 0.000214653 Done calling nodal solver Timestep 30 ends with TIME = 0.1267258932 DT = 0.007851144015 Timing summary: Advection :0.006361275 seconds MAC Proj :0.006259109 seconds Nodal Proj :0.00770177 seconds Reactions :0.012615869 seconds Misc :0.001339655 seconds Base State :8.200001389e-08 seconds Time to advance time step: 0.034467689 Call to estdt for level 0 gives dt_lev = 1.738989551e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 31 gives dt =1e+20 dt_growth factor limits the new dt = 0.008243701216  Timestep 31 starts with TIME = 0.1267258932 DT = 0.008243701216 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.143997884e-29 MLMG: Initial residual (resid0) = 1.143997884e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.075244338e-39, 9.399006352e-11 MLMG: Timers: Solve = 0.005244222 Iter = 0.005025821 Bottom = 0.00012114 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.143997884e-29 MLMG: Initial residual (resid0) = 1.075244338e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000220723 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.744588982e-19 MLMG: Initial residual (resid0) = 4.744588982e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.409524954e-30, 1.772445408e-11 MLMG: Timers: Solve = 0.006860776 Iter = 0.00665275 Bottom = 0.000215537 Done calling nodal solver Timestep 31 ends with TIME = 0.1349695944 DT = 0.008243701216 Timing summary: Advection :0.006402486 seconds MAC Proj :0.006230502 seconds Nodal Proj :0.007644414 seconds Reactions :0.012435944 seconds Misc :0.001390824 seconds Base State :1.779999934e-07 seconds Time to advance time step: 0.034291811 Call to estdt for level 0 gives dt_lev = 1.656272178e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 32 gives dt =1e+20 dt_growth factor limits the new dt = 0.008655886277  Timestep 32 starts with TIME = 0.1349695944 DT = 0.008655886277 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.20132055e-29 MLMG: Initial residual (resid0) = 1.20132055e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.128845405e-39, 9.396704365e-11 MLMG: Timers: Solve = 0.005344097 Iter = 0.005120204 Bottom = 0.000122569 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.20132055e-29 MLMG: Initial residual (resid0) = 1.128845405e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000235878 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.981818431e-19 MLMG: Initial residual (resid0) = 4.981818431e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.830051757e-30, 1.772455556e-11 MLMG: Timers: Solve = 0.007282012 Iter = 0.007042507 Bottom = 0.000218091 Done calling nodal solver Timestep 32 ends with TIME = 0.1436254807 DT = 0.008655886277 Timing summary: Advection :0.006354589 seconds MAC Proj :0.006368691 seconds Nodal Proj :0.008091597 seconds Reactions :0.012259618 seconds Misc :0.001355637 seconds Base State :9.19999934e-08 seconds Time to advance time step: 0.034624555 Call to estdt for level 0 gives dt_lev = 1.57745258e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 33 gives dt =1e+20 dt_growth factor limits the new dt = 0.00908868059  Timestep 33 starts with TIME = 0.1436254807 DT = 0.00908868059 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.261518372e-29 MLMG: Initial residual (resid0) = 1.261518372e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.185446653e-39, 9.396982869e-11 MLMG: Timers: Solve = 0.005284112 Iter = 0.005023741 Bottom = 0.000121241 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.261518372e-29 MLMG: Initial residual (resid0) = 1.185446653e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000219614 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.230909353e-19 MLMG: Initial residual (resid0) = 5.230909353e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.271571197e-30, 1.772458778e-11 MLMG: Timers: Solve = 0.006908656 Iter = 0.006694274 Bottom = 0.00020771 Done calling nodal solver Timestep 33 ends with TIME = 0.1527141613 DT = 0.00908868059 Timing summary: Advection :0.006373875 seconds MAC Proj :0.006276064 seconds Nodal Proj :0.007708546 seconds Reactions :0.012345702 seconds Misc :0.001369213 seconds Base State :8.100002447e-08 seconds Time to advance time step: 0.034230091 Call to estdt for level 0 gives dt_lev = 1.502382666e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 34 gives dt =1e+20 dt_growth factor limits the new dt = 0.00954311462  Timestep 34 starts with TIME = 0.1527141613 DT = 0.00954311462 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.324617027e-29 MLMG: Initial residual (resid0) = 1.324617027e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.244727183e-39, 9.396883457e-11 MLMG: Timers: Solve = 0.005272142 Iter = 0.005053411 Bottom = 0.000122507 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.324617027e-29 MLMG: Initial residual (resid0) = 1.244727183e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000217272 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.49245482e-19 MLMG: Initial residual (resid0) = 5.49245482e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.735142535e-30, 1.772457463e-11 MLMG: Timers: Solve = 0.00690235 Iter = 0.006672799 Bottom = 0.000213018 Done calling nodal solver Timestep 34 ends with TIME = 0.1622572759 DT = 0.00954311462 Timing summary: Advection :0.006239212 seconds MAC Proj :0.006254207 seconds Nodal Proj :0.007718741 seconds Reactions :0.012384651 seconds Misc :0.001332662 seconds Base State :8.399999274e-08 seconds Time to advance time step: 0.034080849 Call to estdt for level 0 gives dt_lev = 1.430870716e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 35 gives dt =1e+20 dt_growth factor limits the new dt = 0.01002027035  Timestep 35 starts with TIME = 0.1622572759 DT = 0.01002027035 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.390880152e-29 MLMG: Initial residual (resid0) = 1.390880152e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.307016301e-39, 9.397044739e-11 MLMG: Timers: Solve = 0.00525617 Iter = 0.005033213 Bottom = 0.000131865 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.390880152e-29 MLMG: Initial residual (resid0) = 1.307016301e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000219958 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.681793327e-19 MLMG: Initial residual (resid0) = 5.681793327e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.549561715e-29, 8.007263646e-11 MLMG: Timers: Solve = 0.006874211 Iter = 0.006667256 Bottom = 0.000211582 Done calling nodal solver Timestep 35 ends with TIME = 0.1722775463 DT = 0.01002027035 Timing summary: Advection :0.006426563 seconds MAC Proj :0.006272176 seconds Nodal Proj :0.007688864 seconds Reactions :0.01217786 seconds Misc :0.00138293 seconds Base State :8.200001389e-08 seconds Time to advance time step: 0.034120815 Call to estdt for level 0 gives dt_lev = 2.977709039e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 36 gives dt =1e+20 dt_growth factor limits the new dt = 0.01052128387  Timestep 36 starts with TIME = 0.1722775463 DT = 0.01052128387 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 4.305515288e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.232267053e-30, 5.184668742e-11 MLMG: Timers: Solve = 0.005306026 Iter = 0.005081366 Bottom = 0.00012859 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 2.232267053e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000220996 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.055431439e-19 MLMG: Initial residual (resid0) = 6.055431439e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.073306314e-29, 1.772468773e-11 MLMG: Timers: Solve = 0.007320084 Iter = 0.00711183 Bottom = 0.000224172 Done calling nodal solver Timestep 36 ends with TIME = 0.1827988301 DT = 0.01052128387 Timing summary: Advection :0.006113248 seconds MAC Proj :0.00626714 seconds Nodal Proj :0.008171283 seconds Reactions :0.012249909 seconds Misc :0.001370425 seconds Base State :8.700001786e-08 seconds Time to advance time step: 0.034332025 Call to estdt for level 0 gives dt_lev = 1.290240107e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 37 gives dt =1e+20 dt_growth factor limits the new dt = 0.01104734806  Timestep 37 starts with TIME = 0.1827988301 DT = 0.01104734806 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.531602761e-29 MLMG: Initial residual (resid0) = 1.531602761e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.182310547e-39, 7.719433372e-11 MLMG: Timers: Solve = 0.005251473 Iter = 0.005035218 Bottom = 0.000120562 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.531602761e-29 MLMG: Initial residual (resid0) = 1.182310547e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000225511 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.264177143e-19 MLMG: Initial residual (resid0) = 6.264177143e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.855293464e-29, 7.750887871e-11 MLMG: Timers: Solve = 0.00688423 Iter = 0.006678913 Bottom = 0.000211401 Done calling nodal solver Timestep 37 ends with TIME = 0.1938461782 DT = 0.01104734806 Timing summary: Advection :0.006248702 seconds MAC Proj :0.006244277 seconds Nodal Proj :0.007701034 seconds Reactions :0.012262782 seconds Misc :0.001348033 seconds Base State :4.200001058e-08 seconds Time to advance time step: 0.033963317 Call to estdt for level 0 gives dt_lev = 2.789553225e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 38 gives dt =1e+20 dt_growth factor limits the new dt = 0.01159971547  Timestep 38 starts with TIME = 0.1938461782 DT = 0.01159971547 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 4.746830605e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.490916131e-30, 5.247535331e-11 MLMG: Timers: Solve = 0.005241194 Iter = 0.005022438 Bottom = 0.000119524 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 2.490916131e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000231598 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.676113162e-19 MLMG: Initial residual (resid0) = 6.676113162e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.183310617e-29, 1.772454403e-11 MLMG: Timers: Solve = 0.006891207 Iter = 0.006677678 Bottom = 0.000212258 Done calling nodal solver Timestep 38 ends with TIME = 0.2054458937 DT = 0.01159971547 Timing summary: Advection :0.006078968 seconds MAC Proj :0.006253271 seconds Nodal Proj :0.007728564 seconds Reactions :0.012219076 seconds Misc :0.00133441 seconds Base State :7.900001719e-08 seconds Time to advance time step: 0.033797463 Call to estdt for level 0 gives dt_lev = 1.16844655e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 39 gives dt =1e+20 dt_growth factor limits the new dt = 0.01217970124  Timestep 39 starts with TIME = 0.2054458937 DT = 0.01217970124 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.536075919e-29 MLMG: Initial residual (resid0) = 1.536075919e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.17936782e-39, 7.677796427e-11 MLMG: Timers: Solve = 0.005349779 Iter = 0.005135382 Bottom = 0.000123888 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.536075919e-29 MLMG: Initial residual (resid0) = 1.17936782e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000229626 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.00991882e-19 MLMG: Initial residual (resid0) = 7.00991882e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.242484815e-29, 1.772466767e-11 MLMG: Timers: Solve = 0.007059765 Iter = 0.006840964 Bottom = 0.000215003 Done calling nodal solver Timestep 39 ends with TIME = 0.2176255949 DT = 0.01217970124 Timing summary: Advection :0.00634152 seconds MAC Proj :0.006327367 seconds Nodal Proj :0.007902929 seconds Reactions :0.012168416 seconds Misc :0.001302155 seconds Base State :2.090000066e-07 seconds Time to advance time step: 0.034210022 Call to estdt for level 0 gives dt_lev = 1.116518296e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 40 gives dt =1e+20 dt_growth factor limits the new dt = 0.0127886863  Timestep 40 starts with TIME = 0.2176255949 DT = 0.0127886863 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.750107688e-29 MLMG: Initial residual (resid0) = 1.750107688e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.667934734e-39, 9.530469151e-11 MLMG: Timers: Solve = 0.005289237 Iter = 0.005062379 Bottom = 0.000119815 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.750107688e-29 MLMG: Initial residual (resid0) = 1.667934734e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000236885 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.360414761e-19 MLMG: Initial residual (resid0) = 7.360414761e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.304605685e-29, 1.772462188e-11 MLMG: Timers: Solve = 0.007000029 Iter = 0.006789188 Bottom = 0.000219622 Done calling nodal solver Timestep 40 ends with TIME = 0.2304142812 DT = 0.0127886863 Timing summary: Advection :0.006343223 seconds MAC Proj :0.006303929 seconds Nodal Proj :0.007816529 seconds Reactions :0.012839372 seconds Misc :0.001404564 seconds Base State :8.500001059e-08 seconds Time to advance time step: 0.034887586 Call to estdt for level 0 gives dt_lev = 1.065046887e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 41 gives dt =1e+20 dt_growth factor limits the new dt = 0.01342812062  Timestep 41 starts with TIME = 0.2304142812 DT = 0.01342812062 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.863121796e-29 MLMG: Initial residual (resid0) = 1.863121796e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.751491358e-39, 9.400841973e-11 MLMG: Timers: Solve = 0.005274263 Iter = 0.005050764 Bottom = 0.000120591 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.863121796e-29 MLMG: Initial residual (resid0) = 1.751491358e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000217914 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.728435499e-19 MLMG: Initial residual (resid0) = 7.728435499e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.369865821e-29, 1.772500814e-11 MLMG: Timers: Solve = 0.006857144 Iter = 0.006651083 Bottom = 0.000211148 Done calling nodal solver Timestep 41 ends with TIME = 0.2438424018 DT = 0.01342812062 Timing summary: Advection :0.006374234 seconds MAC Proj :0.006240872 seconds Nodal Proj :0.007682754 seconds Reactions :0.012332717 seconds Misc :0.001322835 seconds Base State :8.399999274e-08 seconds Time to advance time step: 0.03410757 Call to estdt for level 0 gives dt_lev = 1.015209966e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 42 gives dt =1e+20 dt_growth factor limits the new dt = 0.01409952665  Timestep 42 starts with TIME = 0.2438424018 DT = 0.01409952665 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.957437553e-29 MLMG: Initial residual (resid0) = 1.957437553e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.839212642e-39, 9.396022058e-11 MLMG: Timers: Solve = 0.005295653 Iter = 0.005077594 Bottom = 0.000121565 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.957437553e-29 MLMG: Initial residual (resid0) = 1.839212642e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000219136 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.114857274e-19 MLMG: Initial residual (resid0) = 8.114857274e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.438294112e-29, 1.772420714e-11 MLMG: Timers: Solve = 0.007152124 Iter = 0.006947995 Bottom = 0.000216001 Done calling nodal solver Timestep 42 ends with TIME = 0.2579419285 DT = 0.01409952665 Timing summary: Advection :0.006401779 seconds MAC Proj :0.006295482 seconds Nodal Proj :0.007964293 seconds Reactions :0.01240163 seconds Misc :0.001334634 seconds Base State :5.199999009e-08 seconds Time to advance time step: 0.034545507 Call to estdt for level 0 gives dt_lev = 9.673808914e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 43 gives dt =1e+20 dt_growth factor limits the new dt = 0.01480450298  Timestep 43 starts with TIME = 0.2579419285 DT = 0.01480450298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.055305455e-29 MLMG: Initial residual (resid0) = 2.055305455e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.931045336e-39, 9.395417752e-11 MLMG: Timers: Solve = 0.005361344 Iter = 0.005126343 Bottom = 0.000121416 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.055305455e-29 MLMG: Initial residual (resid0) = 1.931045336e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000220802 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.520600138e-19 MLMG: Initial residual (resid0) = 8.520600138e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.510256484e-29, 1.772476657e-11 MLMG: Timers: Solve = 0.006999182 Iter = 0.00678202 Bottom = 0.000218952 Done calling nodal solver Timestep 43 ends with TIME = 0.2727464314 DT = 0.01480450298 Timing summary: Advection :0.006479318 seconds MAC Proj :0.006367918 seconds Nodal Proj :0.007822474 seconds Reactions :0.012775682 seconds Misc :0.001357105 seconds Base State :8.399999274e-08 seconds Time to advance time step: 0.034957733 Call to estdt for level 0 gives dt_lev = 9.21627116e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 44 gives dt =1e+20 dt_growth factor limits the new dt = 0.01554472813  Timestep 44 starts with TIME = 0.2727464314 DT = 0.01554472813 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.158165969e-29 MLMG: Initial residual (resid0) = 2.158165969e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.027690088e-39, 9.395431664e-11 MLMG: Timers: Solve = 0.005486115 Iter = 0.005267138 Bottom = 0.000120367 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.158165969e-29 MLMG: Initial residual (resid0) = 2.027690088e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000455916 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.946630145e-19 MLMG: Initial residual (resid0) = 8.946630145e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.585743309e-29, 1.772447595e-11 MLMG: Timers: Solve = 0.009581944 Iter = 0.009151605 Bottom = 0.000213789 Done calling nodal solver Timestep 44 ends with TIME = 0.2882911596 DT = 0.01554472813 Timing summary: Advection :0.009434322 seconds MAC Proj :0.006963626 seconds Nodal Proj :0.010906302 seconds Reactions :0.019630157 seconds Misc :0.002174571 seconds Base State :8.899999671e-08 seconds Time to advance time step: 0.049337065 Call to estdt for level 0 gives dt_lev = 8.779254781e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 45 gives dt =1e+20 dt_growth factor limits the new dt = 0.01632196453  Timestep 45 starts with TIME = 0.2882911596 DT = 0.01632196453 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.2662186e-29 MLMG: Initial residual (resid0) = 2.2662186e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.128830206e-39, 9.393754894e-11 MLMG: Timers: Solve = 0.008181845 Iter = 0.00765032 Bottom = 0.000119884 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.2662186e-29 MLMG: Initial residual (resid0) = 2.128830206e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000574333 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.053842861e-18 MLMG: Initial residual (resid0) = 1.053842861e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 6.68124357e-29, 6.339885971e-11 MLMG: Timers: Solve = 0.010376013 Iter = 0.009953 Bottom = 0.000215766 Done calling nodal solver Timestep 45 ends with TIME = 0.3046131241 DT = 0.01632196453 Timing summary: Advection :0.01071863 seconds MAC Proj :0.010003043 seconds Nodal Proj :0.012188901 seconds Reactions :0.024908319 seconds Misc :0.002268816 seconds Base State :8.800000728e-08 seconds Time to advance time step: 0.060334341 Call to estdt for level 0 gives dt_lev = 2.027437947e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 46 gives dt =1e+20 dt_growth factor limits the new dt = 0.01713806276  Timestep 46 starts with TIME = 0.3046131241 DT = 0.01713806276 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 7.013230718e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.387375708e-30, 4.829978999e-11 MLMG: Timers: Solve = 0.005325026 Iter = 0.005092895 Bottom = 0.000120301 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 3.387375708e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000250396 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 9.863659735e-19 MLMG: Initial residual (resid0) = 9.863659735e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.748282166e-29, 1.772447766e-11 MLMG: Timers: Solve = 0.007023049 Iter = 0.006812037 Bottom = 0.000212818 Done calling nodal solver Timestep 46 ends with TIME = 0.3217511869 DT = 0.01713806276 Timing summary: Advection :0.006514178 seconds MAC Proj :0.006374571 seconds Nodal Proj :0.007845442 seconds Reactions :0.013912563 seconds Misc :0.001466523 seconds Base State :9.000001455e-08 seconds Time to advance time step: 0.036321441 Call to estdt for level 0 gives dt_lev = 7.924349732e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 47 gives dt =1e+20 dt_growth factor limits the new dt = 0.0179949659  Timestep 47 starts with TIME = 0.3217511869 DT = 0.0179949659 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.807872089e-29 MLMG: Initial residual (resid0) = 1.807872089e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.373027268e-39, 7.59471467e-11 MLMG: Timers: Solve = 0.005357795 Iter = 0.005134572 Bottom = 0.000123859 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.807872089e-29 MLMG: Initial residual (resid0) = 1.373027268e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000220694 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.035684272e-18 MLMG: Initial residual (resid0) = 1.035684272e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.835709756e-29, 1.772460783e-11 MLMG: Timers: Solve = 0.007445587 Iter = 0.007223679 Bottom = 0.00021733 Done calling nodal solver Timestep 47 ends with TIME = 0.3397461528 DT = 0.0179949659 Timing summary: Advection :0.006739791 seconds MAC Proj :0.006367985 seconds Nodal Proj :0.008292307 seconds Reactions :0.012487017 seconds Misc :0.001351475 seconds Base State :9.100000398e-08 seconds Time to advance time step: 0.035440321 Call to estdt for level 0 gives dt_lev = 7.566055076e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 48 gives dt =1e+20 dt_growth factor limits the new dt = 0.01889471419  Timestep 48 starts with TIME = 0.3397461528 DT = 0.01889471419 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.590316044e-29 MLMG: Initial residual (resid0) = 2.590316044e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.464404755e-39, 9.51391534e-11 MLMG: Timers: Solve = 0.005288585 Iter = 0.005051238 Bottom = 0.000120318 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.590316044e-29 MLMG: Initial residual (resid0) = 2.464404755e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000223457 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.087468486e-18 MLMG: Initial residual (resid0) = 1.087468486e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.927489948e-29, 1.772455913e-11 MLMG: Timers: Solve = 0.00702988 Iter = 0.006822969 Bottom = 0.000217766 Done calling nodal solver Timestep 48 ends with TIME = 0.358640867 DT = 0.01889471419 Timing summary: Advection :0.006580568 seconds MAC Proj :0.006320844 seconds Nodal Proj :0.007854882 seconds Reactions :0.012660321 seconds Misc :0.001809859 seconds Base State :7.500000265e-08 seconds Time to advance time step: 0.035394416 Call to estdt for level 0 gives dt_lev = 7.214097476e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 49 gives dt =1e+20 dt_growth factor limits the new dt = 0.0198394499  Timestep 49 starts with TIME = 0.358640867 DT = 0.0198394499 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.753899991e-29 MLMG: Initial residual (resid0) = 2.753899991e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.587581692e-39, 9.396062678e-11 MLMG: Timers: Solve = 0.005655741 Iter = 0.005421405 Bottom = 0.000120437 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.753899991e-29 MLMG: Initial residual (resid0) = 2.587570482e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00024041 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.086359695e-18 MLMG: Initial residual (resid0) = 1.086359695e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 4.01595875e-29, 3.696711842e-11 MLMG: Timers: Solve = 0.007601852 Iter = 0.007387666 Bottom = 0.000213115 Done calling nodal solver Timestep 49 ends with TIME = 0.3784803169 DT = 0.0198394499 Timing summary: Advection :0.006618929 seconds MAC Proj :0.006679826 seconds Nodal Proj :0.008440595 seconds Reactions :0.013169574 seconds Misc :0.001403111 seconds Base State :9.400000067e-08 seconds Time to advance time step: 0.036465886 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 50 gives dt =1e+20 dt_growth factor limits the new dt = 0.0208314224  Timestep 50 starts with TIME = 0.3784803169 DT = 0.0208314224 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 8.242756114e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.781214371e-30, 4.587318027e-11 MLMG: Timers: Solve = 0.005311727 Iter = 0.005086137 Bottom = 0.000122253 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 3.781214371e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000225989 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.198934006e-18 MLMG: Initial residual (resid0) = 1.198934006e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 2.125061471e-29, 1.772459085e-11 MLMG: Timers: Solve = 0.007270299 Iter = 0.007051537 Bottom = 0.000214555 Done calling nodal solver Timestep 50 ends with TIME = 0.3993117393 DT = 0.0208314224 Timing summary: Advection :0.007945244 seconds MAC Proj :0.006328837 seconds Nodal Proj :0.008116028 seconds Reactions :0.012768734 seconds Misc :0.001384602 seconds Base State :8.999998613e-08 seconds Time to advance time step: 0.036710315 Writing plotfile 50 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.064341457 Writing checkpoint 50 Writing checkpoint chk0000050 Total Time: 3.478671021 Unused ParmParse Variables: [TOP]::amr.check_file(nvals = 1) :: [test_stability_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] AMReX (24.08-4-g4efca7995054) finalized