Initializing AMReX (25.01-3-g3a34576c9930)... MPI initialized with 16 MPI processes MPI initialized with thread support level 0 AMReX (25.01-3-g3a34576c9930) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = 5peaks_const_grav.dat model file = 5peaks_const_grav.dat reading initial model 1000 points found in the initial model 10 variables found in the initial model WARNING: variable not found: gravity WARNING: variable not found: abar WARNING: variable not found: zbar WARNING: variable not found: gpot WARNING: variable not found: cno model file mapping, level: 0 dr of MAESTRO base state = 93750000.000000 dr of input file data = 10010010.010010 maximum radius (cell-centered) of input model = 10000000000.000000 WARNING: resolution of base state array is not an integer multiple of the initial model's resolution. make sure this is a desired property as this could lead to aliasing when performing the interpolation. modulus = 3659909.909910 setting r_cutoff to 105 radius at r_cutoff 9890625000 Maximum HSE Error = 0.054171 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile test_stability_pltInitData after InitData inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.017293346 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.000397717 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile test_stability_pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.015071697 Call to firstdt for level 0 gives dt_lev = 0.01907406555 Multiplying dt_lev by init_shrink; dt_lev = 0.001907406555 Minimum firstdt over all levels = 0.001907406555 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 4.945354899e-27 MLMG: Initial residual (resid0) = 4.945354899e-27 MLMG: Final Iter. 3 resid, resid/bnorm = 2.357566962e-30, 0.0004767235133 MLMG: Timers: Solve = 0.002877778 Iter = 0.002628268 Bottom = 7.6562e-05 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 1 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #2 Calling nodal solver MLMG: Initial rhs = 2.306075226e-30 MLMG: Initial residual (resid0) = 2.306075226e-30 MLMG: Final Iter. 5 resid, resid/bnorm = 1.933642558e-37, 8.384993415e-08 MLMG: Timers: Solve = 0.004154625 Iter = 0.003930677 Bottom = 0.000116809 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 2 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #3 Calling nodal solver MLMG: Initial rhs = 9.742172194e-32 MLMG: Initial residual (resid0) = 9.742172194e-32 MLMG: Final Iter. 4 resid, resid/bnorm = 7.56277059e-41, 7.76292026e-10 MLMG: Timers: Solve = 0.003383974 Iter = 0.003171571 Bottom = 0.000100732 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 3 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Writing plotfile test_stability_pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.013072971 Doing initial pressure iteration #1  Timestep 0 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.893547601e-20 MLMG: Initial residual (resid0) = 4.893547601e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 4.517319639e-31, 9.231175431e-12 MLMG: Timers: Solve = 0.005703433 Iter = 0.005425383 Bottom = 0.000122873 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.893547507e-20 MLMG: Initial residual (resid0) = 2.477484298e-27 MLMG: Final Iter. 4 resid, resid/bnorm = 4.813594317e-30, 9.836615074e-11 MLMG: Timers: Solve = 0.002600762 Iter = 0.002210377 Bottom = 5.3009e-05 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.755411273e-17 MLMG: Initial residual (resid0) = 5.755411273e-17 MLMG: Final Iter. 9 resid, resid/bnorm = 1.020114247e-27, 1.772443703e-11 MLMG: Timers: Solve = 0.013307331 Iter = 0.013065977 Bottom = 0.000235813 Done calling nodal solver Timestep 0 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.007305273 seconds MAC Proj :0.009201011 seconds Nodal Proj :0.02114709 seconds Reactions :0.015758643 seconds Misc :0.004796713 seconds Base State :3.499997092e-08 seconds Time to advance time step: 0.061441296 Writing plotfile 0 after all initialization inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.015764884 Writing checkpoint 0 after all initialization Writing checkpoint chk0000000 Beginning main evolution  Timestep 1 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.257776132e-26 MLMG: Initial residual (resid0) = 1.257776132e-26 MLMG: Final Iter. 10 resid, resid/bnorm = 1.092354528e-37, 8.684808849e-12 MLMG: Timers: Solve = 0.005651126 Iter = 0.005358582 Bottom = 0.000119814 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.257776132e-26 MLMG: Initial residual (resid0) = 1.092354528e-37 MLMG: No iterations needed MLMG: Timers: Solve = 0.000226572 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.097790919e-19 MLMG: Initial residual (resid0) = 1.097790919e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.945791097e-30, 1.772460551e-11 MLMG: Timers: Solve = 0.01153381 Iter = 0.011330846 Bottom = 0.000214544 Done calling nodal solver Timestep 1 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.006761342 seconds MAC Proj :0.006695108 seconds Nodal Proj :0.012678064 seconds Reactions :0.013110711 seconds Misc :0.001801462 seconds Base State :4.900005024e-08 seconds Time to advance time step: 0.046174122 Call to estdt for level 0 gives dt_lev = 7.191087425e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 2 gives dt =1e+20 dt_growth factor limits the new dt = 0.002002776883  Timestep 2 starts with TIME = 0.001907406555 DT = 0.002002776883 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.08039884e-27 MLMG: Initial residual (resid0) = 8.08039884e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 1.160384542e-37, 1.436048597e-11 MLMG: Timers: Solve = 0.005591544 Iter = 0.005371042 Bottom = 0.00012866 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.498306041e-27 MLMG: Initial residual (resid0) = 2.601349809e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 8.687490856e-37, 9.146358118e-11 MLMG: Timers: Solve = 0.005563393 Iter = 0.005322028 Bottom = 0.000117736 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.096671578e-19 MLMG: Initial residual (resid0) = 1.096671578e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.008841827e-29, 9.199124398e-11 MLMG: Timers: Solve = 0.012782986 Iter = 0.012549486 Bottom = 0.000211155 Done calling nodal solver Timestep 2 ends with TIME = 0.003910183437 DT = 0.002002776883 Timing summary: Advection :0.012055742 seconds MAC Proj :0.011957442 seconds Nodal Proj :0.013907075 seconds Reactions :0.017928239 seconds Misc :0.001889575 seconds Base State :5.100002909e-08 seconds Time to advance time step: 0.057961531 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 3 gives dt =1e+20 dt_growth factor limits the new dt = 0.002102915727  Timestep 3 starts with TIME = 0.003910183437 DT = 0.002102915727 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 8.320997544e-21 MLMG: Final Iter. 10 resid, resid/bnorm = 7.677524121e-31, 9.226687161e-11 MLMG: Timers: Solve = 0.011266216 Iter = 0.011048694 Bottom = 0.000123819 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 7.677524121e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000260907 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.21031446e-19 MLMG: Initial residual (resid0) = 1.21031446e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.145245217e-30, 1.772469294e-11 MLMG: Timers: Solve = 0.007466609 Iter = 0.007253994 Bottom = 0.000209812 Done calling nodal solver Timestep 3 ends with TIME = 0.006013099164 DT = 0.002102915727 Timing summary: Advection :0.007401663 seconds MAC Proj :0.012421666 seconds Nodal Proj :0.008369432 seconds Reactions :0.013218221 seconds Misc :0.001697366 seconds Base State :4.200001058e-08 seconds Time to advance time step: 0.043238755 Call to estdt for level 0 gives dt_lev = 6.528670715e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 4 gives dt =1e+20 dt_growth factor limits the new dt = 0.002208061513  Timestep 4 starts with TIME = 0.006013099164 DT = 0.002208061513 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.3079729e-29 MLMG: Initial residual (resid0) = 1.3079729e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.129684783e-39, 8.63691276e-11 MLMG: Timers: Solve = 0.010010715 Iter = 0.009799237 Bottom = 0.000116243 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.3079729e-29 MLMG: Initial residual (resid0) = 1.129684783e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022428 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.270830183e-19 MLMG: Initial residual (resid0) = 1.270830183e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.252519515e-30, 1.772478766e-11 MLMG: Timers: Solve = 0.007064322 Iter = 0.006836504 Bottom = 0.000213594 Done calling nodal solver Timestep 4 ends with TIME = 0.008221160677 DT = 0.002208061513 Timing summary: Advection :0.006384695 seconds MAC Proj :0.011111187 seconds Nodal Proj :0.007954964 seconds Reactions :0.012216974 seconds Misc :0.001565737 seconds Base State :2.210000503e-07 seconds Time to advance time step: 0.039366314 Call to estdt for level 0 gives dt_lev = 6.226377027e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 5 gives dt =1e+20 dt_growth factor limits the new dt = 0.002318464589  Timestep 5 starts with TIME = 0.008221160677 DT = 0.002318464589 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.295423824e-30 MLMG: Initial residual (resid0) = 3.295423824e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.024461011e-40, 9.177760352e-11 MLMG: Timers: Solve = 0.005520881 Iter = 0.005301909 Bottom = 0.000117355 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.295423824e-30 MLMG: Initial residual (resid0) = 3.024461011e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000273635 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.334371692e-19 MLMG: Initial residual (resid0) = 1.334371692e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.365126231e-30, 1.772464333e-11 MLMG: Timers: Solve = 0.007748063 Iter = 0.007540821 Bottom = 0.000217128 Done calling nodal solver Timestep 5 ends with TIME = 0.01053962527 DT = 0.002318464589 Timing summary: Advection :0.007642647 seconds MAC Proj :0.006673789 seconds Nodal Proj :0.008703389 seconds Reactions :0.013683351 seconds Misc :0.001531545 seconds Base State :4.300000001e-08 seconds Time to advance time step: 0.038393197 Call to estdt for level 0 gives dt_lev = 5.914991835e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 6 gives dt =1e+20 dt_growth factor limits the new dt = 0.002434387818  Timestep 6 starts with TIME = 0.01053962527 DT = 0.002434387818 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.377300377e-30 MLMG: Initial residual (resid0) = 3.377300377e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.175447418e-40, 9.402324529e-11 MLMG: Timers: Solve = 0.005759638 Iter = 0.005538054 Bottom = 0.000123735 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.377300377e-30 MLMG: Initial residual (resid0) = 3.175443914e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000228452 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.401090277e-19 MLMG: Initial residual (resid0) = 1.401090277e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.483390367e-30, 1.772469917e-11 MLMG: Timers: Solve = 0.007374105 Iter = 0.007167629 Bottom = 0.000230362 Done calling nodal solver Timestep 6 ends with TIME = 0.01297401308 DT = 0.002434387818 Timing summary: Advection :0.00699657 seconds MAC Proj :0.006756336 seconds Nodal Proj :0.008249966 seconds Reactions :0.013979552 seconds Misc :0.001537639 seconds Base State :3.700006346e-08 seconds Time to advance time step: 0.037675095 Call to estdt for level 0 gives dt_lev = 5.625582499e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 7 gives dt =1e+20 dt_growth factor limits the new dt = 0.002556107209  Timestep 7 starts with TIME = 0.01297401308 DT = 0.002556107209 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.542867857e-30 MLMG: Initial residual (resid0) = 3.542867857e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.33382217e-40, 9.409953474e-11 MLMG: Timers: Solve = 0.005729418 Iter = 0.005493743 Bottom = 0.000122827 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.542867857e-30 MLMG: Initial residual (resid0) = 3.33382217e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000234549 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.471144791e-19 MLMG: Initial residual (resid0) = 1.471144791e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.607576737e-30, 1.772481372e-11 MLMG: Timers: Solve = 0.007358485 Iter = 0.007141207 Bottom = 0.00021627 Done calling nodal solver Timestep 7 ends with TIME = 0.01553012029 DT = 0.002556107209 Timing summary: Advection :0.006922502 seconds MAC Proj :0.006700447 seconds Nodal Proj :0.00824159 seconds Reactions :0.01391656 seconds Misc :0.001502016 seconds Base State :3.699994977e-08 seconds Time to advance time step: 0.03743383 Call to estdt for level 0 gives dt_lev = 5.353302437e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 8 gives dt =1e+20 dt_growth factor limits the new dt = 0.002683912569  Timestep 8 starts with TIME = 0.01553012029 DT = 0.002683912569 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.719890133e-30 MLMG: Initial residual (resid0) = 3.719890133e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.500289421e-40, 9.409658071e-11 MLMG: Timers: Solve = 0.005741107 Iter = 0.005516388 Bottom = 0.000123085 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.719890133e-30 MLMG: Initial residual (resid0) = 3.500289421e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022653 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.54470203e-19 MLMG: Initial residual (resid0) = 1.54470203e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.737926083e-30, 1.77246228e-11 MLMG: Timers: Solve = 0.007392793 Iter = 0.00716351 Bottom = 0.000220161 Done calling nodal solver Timestep 8 ends with TIME = 0.01821403286 DT = 0.002683912569 Timing summary: Advection :0.007010357 seconds MAC Proj :0.00670613 seconds Nodal Proj :0.008267921 seconds Reactions :0.013885657 seconds Misc :0.001516266 seconds Base State :3.599996035e-08 seconds Time to advance time step: 0.037526353 Call to estdt for level 0 gives dt_lev = 5.095587997e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 9 gives dt =1e+20 dt_growth factor limits the new dt = 0.002818108198  Timestep 9 starts with TIME = 0.01821403286 DT = 0.002818108198 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.905661102e-30 MLMG: Initial residual (resid0) = 3.905661102e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.676397606e-40, 9.412996953e-11 MLMG: Timers: Solve = 0.00572664 Iter = 0.005507438 Bottom = 0.000120462 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.905661102e-30 MLMG: Initial residual (resid0) = 3.676397606e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000216905 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.621937132e-19 MLMG: Initial residual (resid0) = 1.621937132e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.874823591e-30, 1.772463022e-11 MLMG: Timers: Solve = 0.007000266 Iter = 0.006799854 Bottom = 0.000221353 Done calling nodal solver Timestep 9 ends with TIME = 0.02103214106 DT = 0.002818108198 Timing summary: Advection :0.006689194 seconds MAC Proj :0.00668484 seconds Nodal Proj :0.007841234 seconds Reactions :0.013350856 seconds Misc :0.001513041 seconds Base State :3.700006346e-08 seconds Time to advance time step: 0.036220404 Call to estdt for level 0 gives dt_lev = 4.851262359e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 10 gives dt =1e+20 dt_growth factor limits the new dt = 0.002959013608  Timestep 10 starts with TIME = 0.02103214106 DT = 0.002959013608 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.100939546e-30 MLMG: Initial residual (resid0) = 4.100939546e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.860100828e-40, 9.412723071e-11 MLMG: Timers: Solve = 0.005440119 Iter = 0.005225444 Bottom = 0.00012126 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.100939546e-30 MLMG: Initial residual (resid0) = 3.860100828e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000216979 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.703033988e-19 MLMG: Initial residual (resid0) = 1.703033988e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.174813655e-29, 6.898357067e-11 MLMG: Timers: Solve = 0.00696203 Iter = 0.006752977 Bottom = 0.000214596 Done calling nodal solver Timestep 10 ends with TIME = 0.02399115467 DT = 0.002959013608 Timing summary: Advection :0.006729616 seconds MAC Proj :0.006388093 seconds Nodal Proj :0.007804653 seconds Reactions :0.013422174 seconds Misc :0.001516406 seconds Base State :4.499997885e-08 seconds Time to advance time step: 0.035995108 Call to estdt for level 0 gives dt_lev = 1.153494089e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 11 gives dt =1e+20 dt_growth factor limits the new dt = 0.003106964288  Timestep 11 starts with TIME = 0.02399115467 DT = 0.003106964288 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 1.271430598e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.310351499e-31, 4.963189897e-11 MLMG: Timers: Solve = 0.005468965 Iter = 0.005233703 Bottom = 0.000120873 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 6.310351499e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000220715 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.788185688e-19 MLMG: Initial residual (resid0) = 1.788185688e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.169478835e-30, 1.772455096e-11 MLMG: Timers: Solve = 0.006968516 Iter = 0.006755621 Bottom = 0.000220214 Done calling nodal solver Timestep 11 ends with TIME = 0.02709811896 DT = 0.003106964288 Timing summary: Advection :0.006341759 seconds MAC Proj :0.006431156 seconds Nodal Proj :0.007820926 seconds Reactions :0.013835889 seconds Misc :0.001497113 seconds Base State :3.699994977e-08 seconds Time to advance time step: 0.036064131 Call to estdt for level 0 gives dt_lev = 4.376646045e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 12 gives dt =1e+20 dt_growth factor limits the new dt = 0.003262312503  Timestep 12 starts with TIME = 0.02709811896 DT = 0.003262312503 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.931087603e-30 MLMG: Initial residual (resid0) = 2.931087603e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.211756947e-40, 7.545857536e-11 MLMG: Timers: Solve = 0.00552136 Iter = 0.005308245 Bottom = 0.000121307 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.931087603e-30 MLMG: Initial residual (resid0) = 2.211756947e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000216164 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.877594972e-19 MLMG: Initial residual (resid0) = 1.877594972e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.327886573e-30, 1.772419836e-11 MLMG: Timers: Solve = 0.007064382 Iter = 0.006856917 Bottom = 0.000215865 Done calling nodal solver Timestep 12 ends with TIME = 0.03036043146 DT = 0.003262312503 Timing summary: Advection :0.006402784 seconds MAC Proj :0.006454808 seconds Nodal Proj :0.007894984 seconds Reactions :0.012303976 seconds Misc :0.001490294 seconds Base State :4.399998943e-08 seconds Time to advance time step: 0.034678463 Call to estdt for level 0 gives dt_lev = 4.177453783e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 13 gives dt =1e+20 dt_growth factor limits the new dt = 0.003425428128  Timestep 13 starts with TIME = 0.03036043146 DT = 0.003425428128 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.688248856e-30 MLMG: Initial residual (resid0) = 4.688248856e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.467598744e-40, 9.52935495e-11 MLMG: Timers: Solve = 0.005462281 Iter = 0.00524733 Bottom = 0.000121277 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.688248856e-30 MLMG: Initial residual (resid0) = 4.467598744e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000217274 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.971474721e-19 MLMG: Initial residual (resid0) = 1.971474721e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.494310995e-30, 1.7724351e-11 MLMG: Timers: Solve = 0.0069369 Iter = 0.006734665 Bottom = 0.00021438 Done calling nodal solver Timestep 13 ends with TIME = 0.03378585959 DT = 0.003425428128 Timing summary: Advection :0.006593428 seconds MAC Proj :0.006385218 seconds Nodal Proj :0.007803206 seconds Reactions :0.012340615 seconds Misc :0.001503334 seconds Base State :4.899993655e-08 seconds Time to advance time step: 0.034776358 Call to estdt for level 0 gives dt_lev = 3.982247017e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 14 gives dt =1e+20 dt_growth factor limits the new dt = 0.003596699534  Timestep 14 starts with TIME = 0.03378585959 DT = 0.003596699534 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.98227213e-30 MLMG: Initial residual (resid0) = 4.98227213e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.691855544e-40, 9.417100114e-11 MLMG: Timers: Solve = 0.005500327 Iter = 0.005236247 Bottom = 0.00012121 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.98227213e-30 MLMG: Initial residual (resid0) = 4.691855544e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000216594 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.221658729e-19 MLMG: Initial residual (resid0) = 2.221658729e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.863225901e-30, 3.989463271e-11 MLMG: Timers: Solve = 0.007001834 Iter = 0.006777051 Bottom = 0.000219049 Done calling nodal solver Timestep 14 ends with TIME = 0.03738255912 DT = 0.003596699534 Timing summary: Advection :0.006447124 seconds MAC Proj :0.006434644 seconds Nodal Proj :0.007888899 seconds Reactions :0.012371608 seconds Misc :0.001515591 seconds Base State :3.599996035e-08 seconds Time to advance time step: 0.034790145 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 15 gives dt =1e+20 dt_growth factor limits the new dt = 0.003776534511  Timestep 15 starts with TIME = 0.03738255912 DT = 0.003776534511 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 1.44706648e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 8.546351457e-31, 5.905983986e-11 MLMG: Timers: Solve = 0.005570521 Iter = 0.005355011 Bottom = 0.000120924 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 8.546351457e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000215839 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.279163939e-19 MLMG: Initial residual (resid0) = 2.279163939e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.500913317e-29, 6.585367956e-11 MLMG: Timers: Solve = 0.006990402 Iter = 0.00677442 Bottom = 0.000219966 Done calling nodal solver Timestep 15 ends with TIME = 0.04115909363 DT = 0.003776534511 Timing summary: Advection :0.006309685 seconds MAC Proj :0.006492455 seconds Nodal Proj :0.007845837 seconds Reactions :0.012270545 seconds Misc :0.001488055 seconds Base State :4.200001058e-08 seconds Time to advance time step: 0.034552652 Call to estdt for level 0 gives dt_lev = 9.044183602e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 16 gives dt =1e+20 dt_growth factor limits the new dt = 0.003965361236  Timestep 16 starts with TIME = 0.04115909363 DT = 0.003965361236 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 1.62270343e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.18605137e-31, 3.812188509e-11 MLMG: Timers: Solve = 0.005936443 Iter = 0.005668771 Bottom = 0.000140411 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 6.18605137e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000266324 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.282228424e-19 MLMG: Initial residual (resid0) = 2.282228424e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.045223255e-30, 1.772488333e-11 MLMG: Timers: Solve = 0.006950107 Iter = 0.006751696 Bottom = 0.000212844 Done calling nodal solver Timestep 16 ends with TIME = 0.04512445487 DT = 0.003965361236 Timing summary: Advection :0.006483587 seconds MAC Proj :0.006949979 seconds Nodal Proj :0.00781303 seconds Reactions :0.013799313 seconds Misc :0.001494514 seconds Base State :3.800005288e-08 seconds Time to advance time step: 0.036679781 Call to estdt for level 0 gives dt_lev = 3.436635199e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 17 gives dt =1e+20 dt_growth factor limits the new dt = 0.004163629298  Timestep 17 starts with TIME = 0.04512445487 DT = 0.004163629298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.754712132e-30 MLMG: Initial residual (resid0) = 3.754712132e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.82584447e-40, 7.526128158e-11 MLMG: Timers: Solve = 0.005520727 Iter = 0.00530969 Bottom = 0.00012135 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.754712132e-30 MLMG: Initial residual (resid0) = 2.82584447e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000219151 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.396339845e-19 MLMG: Initial residual (resid0) = 2.396339845e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.247421825e-30, 1.772462213e-11 MLMG: Timers: Solve = 0.006991831 Iter = 0.006790245 Bottom = 0.000217292 Done calling nodal solver Timestep 17 ends with TIME = 0.04928808417 DT = 0.004163629298 Timing summary: Advection :0.006395503 seconds MAC Proj :0.006438727 seconds Nodal Proj :0.007817226 seconds Reactions :0.012263827 seconds Misc :0.001494217 seconds Base State :4.859999763e-07 seconds Time to advance time step: 0.034547414 Call to estdt for level 0 gives dt_lev = 3.276873657e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 18 gives dt =1e+20 dt_growth factor limits the new dt = 0.004371810763  Timestep 18 starts with TIME = 0.04928808417 DT = 0.004371810763 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.988437125e-30 MLMG: Initial residual (resid0) = 5.988437125e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.701673257e-40, 9.521137381e-11 MLMG: Timers: Solve = 0.005693947 Iter = 0.005439085 Bottom = 0.000142466 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.988437125e-30 MLMG: Initial residual (resid0) = 5.701673257e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000262355 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.516156837e-19 MLMG: Initial residual (resid0) = 2.516156837e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.459779676e-30, 1.772456951e-11 MLMG: Timers: Solve = 0.007284999 Iter = 0.007051119 Bottom = 0.000255335 Done calling nodal solver Timestep 18 ends with TIME = 0.05365989493 DT = 0.004371810763 Timing summary: Advection :0.00666138 seconds MAC Proj :0.006693858 seconds Nodal Proj :0.008144095 seconds Reactions :0.01333474 seconds Misc :0.001491016 seconds Base State :4.300000001e-08 seconds Time to advance time step: 0.036464008 Call to estdt for level 0 gives dt_lev = 3.122293372e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 19 gives dt =1e+20 dt_growth factor limits the new dt = 0.004590401301  Timestep 19 starts with TIME = 0.05365989493 DT = 0.004590401301 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.361637466e-30 MLMG: Initial residual (resid0) = 6.361637466e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.987748338e-40, 9.41227533e-11 MLMG: Timers: Solve = 0.005684949 Iter = 0.00543333 Bottom = 0.000138866 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.361637466e-30 MLMG: Initial residual (resid0) = 5.987748338e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000223852 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.641964679e-19 MLMG: Initial residual (resid0) = 2.641964679e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.68289866e-30, 1.772506157e-11 MLMG: Timers: Solve = 0.007044088 Iter = 0.006815291 Bottom = 0.000217654 Done calling nodal solver Timestep 19 ends with TIME = 0.05825029623 DT = 0.004590401301 Timing summary: Advection :0.006561112 seconds MAC Proj :0.006635943 seconds Nodal Proj :0.00788857 seconds Reactions :0.013231721 seconds Misc :0.001485334 seconds Base State :4.300000001e-08 seconds Time to advance time step: 0.035939081 Call to estdt for level 0 gives dt_lev = 2.974235616e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 20 gives dt =1e+20 dt_growth factor limits the new dt = 0.004819921366  Timestep 20 starts with TIME = 0.05825029623 DT = 0.004819921366 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.682786498e-30 MLMG: Initial residual (resid0) = 6.682786498e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.287114735e-40, 9.407923982e-11 MLMG: Timers: Solve = 0.005499445 Iter = 0.005272148 Bottom = 0.000119055 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.682786498e-30 MLMG: Initial residual (resid0) = 6.287114735e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000227935 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.774062913e-19 MLMG: Initial residual (resid0) = 2.774062913e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.916875074e-30, 1.772445409e-11 MLMG: Timers: Solve = 0.006944772 Iter = 0.006742998 Bottom = 0.000215312 Done calling nodal solver Timestep 20 ends with TIME = 0.0630702176 DT = 0.004819921366 Timing summary: Advection :0.006527708 seconds MAC Proj :0.006415831 seconds Nodal Proj :0.007805849 seconds Reactions :0.012321784 seconds Misc :0.001495751 seconds Base State :3.700006346e-08 seconds Time to advance time step: 0.034716329 Call to estdt for level 0 gives dt_lev = 2.832901245e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 21 gives dt =1e+20 dt_growth factor limits the new dt = 0.005060917435  Timestep 21 starts with TIME = 0.0630702176 DT = 0.005060917435 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.017767486e-30 MLMG: Initial residual (resid0) = 7.017767486e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.601040624e-40, 9.406183144e-11 MLMG: Timers: Solve = 0.005462029 Iter = 0.005234883 Bottom = 0.000120778 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.017767486e-30 MLMG: Initial residual (resid0) = 6.601040624e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000217929 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.869691725e-19 MLMG: Initial residual (resid0) = 2.869691725e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.297839054e-29, 8.007267937e-11 MLMG: Timers: Solve = 0.007147868 Iter = 0.006808494 Bottom = 0.000220199 Done calling nodal solver Timestep 21 ends with TIME = 0.06813113503 DT = 0.005060917435 Timing summary: Advection :0.006475696 seconds MAC Proj :0.006419043 seconds Nodal Proj :0.008000462 seconds Reactions :0.012257525 seconds Misc :0.001505205 seconds Base State :4.099990747e-08 seconds Time to advance time step: 0.034788701 Call to estdt for level 0 gives dt_lev = 5.895649157e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 22 gives dt =1e+20 dt_growth factor limits the new dt = 0.005313963306  Timestep 22 starts with TIME = 0.06813113503 DT = 0.005313963306 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 2.174577793e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 1.127453232e-30, 5.184699467e-11 MLMG: Timers: Solve = 0.005467978 Iter = 0.005226635 Bottom = 0.000121805 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 1.127453232e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000219868 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.058404362e-19 MLMG: Initial residual (resid0) = 3.058404362e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.420842792e-30, 1.772441493e-11 MLMG: Timers: Solve = 0.006977909 Iter = 0.006775076 Bottom = 0.000219404 Done calling nodal solver Timestep 22 ends with TIME = 0.07344509834 DT = 0.005313963306 Timing summary: Advection :0.006286696 seconds MAC Proj :0.006416995 seconds Nodal Proj :0.00783378 seconds Reactions :0.012407468 seconds Misc :0.001489465 seconds Base State :3.699994977e-08 seconds Time to advance time step: 0.034563857 Call to estdt for level 0 gives dt_lev = 2.554660013e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 23 gives dt =1e+20 dt_growth factor limits the new dt = 0.005579661472  Timestep 23 starts with TIME = 0.07344509834 DT = 0.005579661472 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.73348257e-30 MLMG: Initial residual (resid0) = 7.73348257e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.972845529e-40, 7.723358105e-11 MLMG: Timers: Solve = 0.005446912 Iter = 0.005230532 Bottom = 0.000121769 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.73348257e-30 MLMG: Initial residual (resid0) = 5.972845529e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000214434 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.21132458e-19 MLMG: Initial residual (resid0) = 3.21132458e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.691941506e-30, 1.77245911e-11 MLMG: Timers: Solve = 0.006981719 Iter = 0.006774645 Bottom = 0.000215024 Done calling nodal solver Timestep 23 ends with TIME = 0.07902475981 DT = 0.005579661472 Timing summary: Advection :0.006359443 seconds MAC Proj :0.00639259 seconds Nodal Proj :0.007819105 seconds Reactions :0.012356029 seconds Misc :0.00148894 seconds Base State :4.399998943e-08 seconds Time to advance time step: 0.034544479 Call to estdt for level 0 gives dt_lev = 2.439862005e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 24 gives dt =1e+20 dt_growth factor limits the new dt = 0.005858644545  Timestep 24 starts with TIME = 0.07902475981 DT = 0.005858644545 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.00564811e-30 MLMG: Initial residual (resid0) = 8.00564811e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 7.641742954e-40, 9.545439482e-11 MLMG: Timers: Solve = 0.005476875 Iter = 0.005259201 Bottom = 0.000121425 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.00564811e-30 MLMG: Initial residual (resid0) = 7.641742954e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000216614 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.371890809e-19 MLMG: Initial residual (resid0) = 3.371890809e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.976593952e-30, 1.772475531e-11 MLMG: Timers: Solve = 0.006974434 Iter = 0.006762059 Bottom = 0.000216754 Done calling nodal solver Timestep 24 ends with TIME = 0.08488340435 DT = 0.005858644545 Timing summary: Advection :0.006579922 seconds MAC Proj :0.006486178 seconds Nodal Proj :0.007839903 seconds Reactions :0.012294137 seconds Misc :0.001500658 seconds Base State :4.100002116e-08 seconds Time to advance time step: 0.034854 Call to estdt for level 0 gives dt_lev = 2.326582163e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 25 gives dt =1e+20 dt_growth factor limits the new dt = 0.006151576773  Timestep 25 starts with TIME = 0.08488340435 DT = 0.006151576773 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.527771313e-30 MLMG: Initial residual (resid0) = 8.527771313e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.024857955e-40, 9.410264019e-11 MLMG: Timers: Solve = 0.005509561 Iter = 0.00529433 Bottom = 0.000131735 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.527771313e-30 MLMG: Initial residual (resid0) = 8.024857955e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000221478 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.540485349e-19 MLMG: Initial residual (resid0) = 3.540485349e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.275353834e-30, 1.772455812e-11 MLMG: Timers: Solve = 0.006980671 Iter = 0.006780156 Bottom = 0.000216087 Done calling nodal solver Timestep 25 ends with TIME = 0.09103498113 DT = 0.006151576773 Timing summary: Advection :0.006525503 seconds MAC Proj :0.00644351 seconds Nodal Proj :0.00785113 seconds Reactions :0.01224564 seconds Misc :0.001483893 seconds Base State :4.399998943e-08 seconds Time to advance time step: 0.034699796 Call to estdt for level 0 gives dt_lev = 2.21729507e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 26 gives dt =1e+20 dt_growth factor limits the new dt = 0.006459155611  Timestep 26 starts with TIME = 0.09103498113 DT = 0.006459155611 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.960012316e-30 MLMG: Initial residual (resid0) = 8.960012316e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.424844588e-40, 9.402715411e-11 MLMG: Timers: Solve = 0.00547013 Iter = 0.005243743 Bottom = 0.00012068 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.960012316e-30 MLMG: Initial residual (resid0) = 8.424844588e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000215332 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.717509617e-19 MLMG: Initial residual (resid0) = 3.717509617e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.58913597e-30, 1.772459698e-11 MLMG: Timers: Solve = 0.006955135 Iter = 0.006754123 Bottom = 0.000214315 Done calling nodal solver Timestep 26 ends with TIME = 0.09749413674 DT = 0.006459155611 Timing summary: Advection :0.006830326 seconds MAC Proj :0.006408058 seconds Nodal Proj :0.00780705 seconds Reactions :0.01377588 seconds Misc :0.001510385 seconds Base State :6.399989161e-08 seconds Time to advance time step: 0.036463141 Call to estdt for level 0 gives dt_lev = 2.112511375e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 27 gives dt =1e+20 dt_growth factor limits the new dt = 0.006782113392  Timestep 27 starts with TIME = 0.09749413674 DT = 0.006782113392 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.408830982e-30 MLMG: Initial residual (resid0) = 9.408830982e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.846691478e-40, 9.402540544e-11 MLMG: Timers: Solve = 0.00546019 Iter = 0.00524262 Bottom = 0.000121131 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.408830982e-30 MLMG: Initial residual (resid0) = 8.846691478e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000217103 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.903385097e-19 MLMG: Initial residual (resid0) = 3.903385097e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.918614436e-30, 1.772465248e-11 MLMG: Timers: Solve = 0.006980194 Iter = 0.006771525 Bottom = 0.000220607 Done calling nodal solver Timestep 27 ends with TIME = 0.1042762501 DT = 0.006782113392 Timing summary: Advection :0.006490992 seconds MAC Proj :0.006395537 seconds Nodal Proj :0.007829816 seconds Reactions :0.012777958 seconds Misc :0.001494343 seconds Base State :4.200001058e-08 seconds Time to advance time step: 0.035135632 Call to estdt for level 0 gives dt_lev = 2.0124204e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 28 gives dt =1e+20 dt_growth factor limits the new dt = 0.007121219061  Timestep 28 starts with TIME = 0.1042762501 DT = 0.007121219061 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.880130395e-30 MLMG: Initial residual (resid0) = 9.880130395e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 9.288520884e-40, 9.40121285e-11 MLMG: Timers: Solve = 0.005551482 Iter = 0.00533429 Bottom = 0.000121062 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.880130395e-30 MLMG: Initial residual (resid0) = 9.288520884e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000219494 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.098554352e-19 MLMG: Initial residual (resid0) = 4.098554352e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.264511454e-30, 1.772457025e-11 MLMG: Timers: Solve = 0.007068289 Iter = 0.006859478 Bottom = 0.000213581 Done calling nodal solver Timestep 28 ends with TIME = 0.1113974692 DT = 0.007121219061 Timing summary: Advection :0.006526704 seconds MAC Proj :0.006461901 seconds Nodal Proj :0.007910448 seconds Reactions :0.012277579 seconds Misc :0.001499433 seconds Base State :9.500001852e-08 seconds Time to advance time step: 0.034807882 Call to estdt for level 0 gives dt_lev = 1.916904797e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 29 gives dt =1e+20 dt_growth factor limits the new dt = 0.007477280014  Timestep 29 starts with TIME = 0.1113974692 DT = 0.007477280014 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.037425901e-29 MLMG: Initial residual (resid0) = 1.037425901e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 9.752925208e-40, 9.401081271e-11 MLMG: Timers: Solve = 0.005481494 Iter = 0.005253279 Bottom = 0.000120573 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.037425901e-29 MLMG: Initial residual (resid0) = 9.752925208e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022358 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.30348207e-19 MLMG: Initial residual (resid0) = 4.30348207e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.627838138e-30, 1.77248052e-11 MLMG: Timers: Solve = 0.007042797 Iter = 0.006827251 Bottom = 0.000214926 Done calling nodal solver Timestep 29 ends with TIME = 0.1188747492 DT = 0.007477280014 Timing summary: Advection :0.006577146 seconds MAC Proj :0.006427657 seconds Nodal Proj :0.00788802 seconds Reactions :0.013332653 seconds Misc :0.001507012 seconds Base State :4.999992598e-08 seconds Time to advance time step: 0.035875344 Call to estdt for level 0 gives dt_lev = 1.825812456e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 30 gives dt =1e+20 dt_growth factor limits the new dt = 0.007851144015  Timestep 30 starts with TIME = 0.1188747492 DT = 0.007851144015 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.08944873e-29 MLMG: Initial residual (resid0) = 1.08944873e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.023977833e-39, 9.399045635e-11 MLMG: Timers: Solve = 0.005406349 Iter = 0.005191479 Bottom = 0.000119384 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.08944873e-29 MLMG: Initial residual (resid0) = 1.023977833e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000213064 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.518656173e-19 MLMG: Initial residual (resid0) = 4.518656173e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.00907597e-30, 1.772446423e-11 MLMG: Timers: Solve = 0.006963182 Iter = 0.006761886 Bottom = 0.000219582 Done calling nodal solver Timestep 30 ends with TIME = 0.1267258932 DT = 0.007851144015 Timing summary: Advection :0.006742176 seconds MAC Proj :0.006331608 seconds Nodal Proj :0.007801798 seconds Reactions :0.012886408 seconds Misc :0.001490896 seconds Base State :3.599996035e-08 seconds Time to advance time step: 0.035390215 Call to estdt for level 0 gives dt_lev = 1.738989551e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 31 gives dt =1e+20 dt_growth factor limits the new dt = 0.008243701216  Timestep 31 starts with TIME = 0.1267258932 DT = 0.008243701216 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.143997884e-29 MLMG: Initial residual (resid0) = 1.143997884e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.075244338e-39, 9.399006352e-11 MLMG: Timers: Solve = 0.005613998 Iter = 0.005400079 Bottom = 0.000119662 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.143997884e-29 MLMG: Initial residual (resid0) = 1.075244338e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000219323 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.744588982e-19 MLMG: Initial residual (resid0) = 4.744588982e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.409524954e-30, 1.772445408e-11 MLMG: Timers: Solve = 0.007031732 Iter = 0.006826636 Bottom = 0.000223678 Done calling nodal solver Timestep 31 ends with TIME = 0.1349695944 DT = 0.008243701216 Timing summary: Advection :0.006699764 seconds MAC Proj :0.006572061 seconds Nodal Proj :0.007882047 seconds Reactions :0.012684492 seconds Misc :0.001496059 seconds Base State :4.399998943e-08 seconds Time to advance time step: 0.035472634 Call to estdt for level 0 gives dt_lev = 1.656272178e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 32 gives dt =1e+20 dt_growth factor limits the new dt = 0.008655886277  Timestep 32 starts with TIME = 0.1349695944 DT = 0.008655886277 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.20132055e-29 MLMG: Initial residual (resid0) = 1.20132055e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.128845405e-39, 9.396704365e-11 MLMG: Timers: Solve = 0.005584152 Iter = 0.005367868 Bottom = 0.000122474 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.20132055e-29 MLMG: Initial residual (resid0) = 1.128845405e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000231126 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.981818431e-19 MLMG: Initial residual (resid0) = 4.981818431e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.830051757e-30, 1.772455556e-11 MLMG: Timers: Solve = 0.006937851 Iter = 0.006723124 Bottom = 0.000213376 Done calling nodal solver Timestep 32 ends with TIME = 0.1436254807 DT = 0.008655886277 Timing summary: Advection :0.006477342 seconds MAC Proj :0.006545077 seconds Nodal Proj :0.007803903 seconds Reactions :0.012457732 seconds Misc :0.001528079 seconds Base State :3.800005288e-08 seconds Time to advance time step: 0.034950137 Call to estdt for level 0 gives dt_lev = 1.57745258e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 33 gives dt =1e+20 dt_growth factor limits the new dt = 0.00908868059  Timestep 33 starts with TIME = 0.1436254807 DT = 0.00908868059 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.261518372e-29 MLMG: Initial residual (resid0) = 1.261518372e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.185446653e-39, 9.396982869e-11 MLMG: Timers: Solve = 0.005451355 Iter = 0.005234202 Bottom = 0.000120466 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.261518372e-29 MLMG: Initial residual (resid0) = 1.185446653e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000225082 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.230909353e-19 MLMG: Initial residual (resid0) = 5.230909353e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.271571197e-30, 1.772458778e-11 MLMG: Timers: Solve = 0.006977527 Iter = 0.006778456 Bottom = 0.000216682 Done calling nodal solver Timestep 33 ends with TIME = 0.1527141613 DT = 0.00908868059 Timing summary: Advection :0.006466414 seconds MAC Proj :0.006405276 seconds Nodal Proj :0.007823814 seconds Reactions :0.012327803 seconds Misc :0.001534322 seconds Base State :5.200001851e-08 seconds Time to advance time step: 0.034702546 Call to estdt for level 0 gives dt_lev = 1.502382666e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 34 gives dt =1e+20 dt_growth factor limits the new dt = 0.00954311462  Timestep 34 starts with TIME = 0.1527141613 DT = 0.00954311462 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.324617027e-29 MLMG: Initial residual (resid0) = 1.324617027e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.244727183e-39, 9.396883457e-11 MLMG: Timers: Solve = 0.005424759 Iter = 0.005207829 Bottom = 0.000121114 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.324617027e-29 MLMG: Initial residual (resid0) = 1.244727183e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000221465 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.49245482e-19 MLMG: Initial residual (resid0) = 5.49245482e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.735142535e-30, 1.772457463e-11 MLMG: Timers: Solve = 0.007027018 Iter = 0.006824013 Bottom = 0.000222038 Done calling nodal solver Timestep 34 ends with TIME = 0.1622572759 DT = 0.00954311462 Timing summary: Advection :0.006486642 seconds MAC Proj :0.006363341 seconds Nodal Proj :0.00787115 seconds Reactions :0.012786055 seconds Misc :0.001490585 seconds Base State :4.200001058e-08 seconds Time to advance time step: 0.035132059 Call to estdt for level 0 gives dt_lev = 1.430870716e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 35 gives dt =1e+20 dt_growth factor limits the new dt = 0.01002027035  Timestep 35 starts with TIME = 0.1622572759 DT = 0.01002027035 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.390880152e-29 MLMG: Initial residual (resid0) = 1.390880152e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.307016301e-39, 9.397044739e-11 MLMG: Timers: Solve = 0.005449425 Iter = 0.005234195 Bottom = 0.000120939 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.390880152e-29 MLMG: Initial residual (resid0) = 1.307016301e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000265416 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.681793327e-19 MLMG: Initial residual (resid0) = 5.681793327e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.549561715e-29, 8.007263646e-11 MLMG: Timers: Solve = 0.006961045 Iter = 0.006760965 Bottom = 0.000216307 Done calling nodal solver Timestep 35 ends with TIME = 0.1722775463 DT = 0.01002027035 Timing summary: Advection :0.006495854 seconds MAC Proj :0.006427958 seconds Nodal Proj :0.007797813 seconds Reactions :0.012436705 seconds Misc :0.001496738 seconds Base State :3.599996035e-08 seconds Time to advance time step: 0.034789395 Call to estdt for level 0 gives dt_lev = 2.977709039e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 36 gives dt =1e+20 dt_growth factor limits the new dt = 0.01052128387  Timestep 36 starts with TIME = 0.1722775463 DT = 0.01052128387 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 4.305515288e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.232267053e-30, 5.184668742e-11 MLMG: Timers: Solve = 0.005467608 Iter = 0.005251408 Bottom = 0.000119824 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 2.232267053e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000232049 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.055431439e-19 MLMG: Initial residual (resid0) = 6.055431439e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.073306314e-29, 1.772468773e-11 MLMG: Timers: Solve = 0.00697682 Iter = 0.006747198 Bottom = 0.00021575 Done calling nodal solver Timestep 36 ends with TIME = 0.1827988301 DT = 0.01052128387 Timing summary: Advection :0.006201604 seconds MAC Proj :0.006414839 seconds Nodal Proj :0.007823923 seconds Reactions :0.012224136 seconds Misc :0.001491776 seconds Base State :3.499997092e-08 seconds Time to advance time step: 0.03428896 Call to estdt for level 0 gives dt_lev = 1.290240107e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 37 gives dt =1e+20 dt_growth factor limits the new dt = 0.01104734806  Timestep 37 starts with TIME = 0.1827988301 DT = 0.01104734806 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.531602761e-29 MLMG: Initial residual (resid0) = 1.531602761e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.182310547e-39, 7.719433372e-11 MLMG: Timers: Solve = 0.005426233 Iter = 0.005220299 Bottom = 0.000120813 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.531602761e-29 MLMG: Initial residual (resid0) = 1.182310547e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000218428 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.264177143e-19 MLMG: Initial residual (resid0) = 6.264177143e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.855293464e-29, 7.750887871e-11 MLMG: Timers: Solve = 0.006946913 Iter = 0.006732816 Bottom = 0.000216026 Done calling nodal solver Timestep 37 ends with TIME = 0.1938461782 DT = 0.01104734806 Timing summary: Advection :0.006341572 seconds MAC Proj :0.006379717 seconds Nodal Proj :0.007790915 seconds Reactions :0.012227962 seconds Misc :0.001490311 seconds Base State :5.199990483e-08 seconds Time to advance time step: 0.034369168 Call to estdt for level 0 gives dt_lev = 2.789553225e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 38 gives dt =1e+20 dt_growth factor limits the new dt = 0.01159971547  Timestep 38 starts with TIME = 0.1938461782 DT = 0.01159971547 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 4.746830605e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.490916131e-30, 5.247535331e-11 MLMG: Timers: Solve = 0.005483016 Iter = 0.005215978 Bottom = 0.000124675 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 2.490916131e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.00021697 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.676113162e-19 MLMG: Initial residual (resid0) = 6.676113162e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.183310617e-29, 1.772454403e-11 MLMG: Timers: Solve = 0.007029938 Iter = 0.006818843 Bottom = 0.000217665 Done calling nodal solver Timestep 38 ends with TIME = 0.2054458937 DT = 0.01159971547 Timing summary: Advection :0.006250662 seconds MAC Proj :0.006433031 seconds Nodal Proj :0.007880955 seconds Reactions :0.012271338 seconds Misc :0.001505877 seconds Base State :3.999991804e-08 seconds Time to advance time step: 0.034477199 Call to estdt for level 0 gives dt_lev = 1.16844655e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 39 gives dt =1e+20 dt_growth factor limits the new dt = 0.01217970124  Timestep 39 starts with TIME = 0.2054458937 DT = 0.01217970124 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.536075919e-29 MLMG: Initial residual (resid0) = 1.536075919e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.17936782e-39, 7.677796427e-11 MLMG: Timers: Solve = 0.005447043 Iter = 0.005233391 Bottom = 0.000120103 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.536075919e-29 MLMG: Initial residual (resid0) = 1.17936782e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000227554 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.00991882e-19 MLMG: Initial residual (resid0) = 7.00991882e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.242484815e-29, 1.772466767e-11 MLMG: Timers: Solve = 0.006980828 Iter = 0.006782631 Bottom = 0.000216652 Done calling nodal solver Timestep 39 ends with TIME = 0.2176255949 DT = 0.01217970124 Timing summary: Advection :0.006313088 seconds MAC Proj :0.00641279 seconds Nodal Proj :0.00781167 seconds Reactions :0.012399021 seconds Misc :0.001497863 seconds Base State :3.700006346e-08 seconds Time to advance time step: 0.034569725 Call to estdt for level 0 gives dt_lev = 1.116518296e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 40 gives dt =1e+20 dt_growth factor limits the new dt = 0.0127886863  Timestep 40 starts with TIME = 0.2176255949 DT = 0.0127886863 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.750107688e-29 MLMG: Initial residual (resid0) = 1.750107688e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.667934734e-39, 9.530469151e-11 MLMG: Timers: Solve = 0.005650175 Iter = 0.005418248 Bottom = 0.000133222 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.750107688e-29 MLMG: Initial residual (resid0) = 1.667934734e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000223501 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.360414761e-19 MLMG: Initial residual (resid0) = 7.360414761e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.304605685e-29, 1.772462188e-11 MLMG: Timers: Solve = 0.007008586 Iter = 0.006800669 Bottom = 0.000222251 Done calling nodal solver Timestep 40 ends with TIME = 0.2304142812 DT = 0.0127886863 Timing summary: Advection :0.006448315 seconds MAC Proj :0.006591724 seconds Nodal Proj :0.007840455 seconds Reactions :0.012703158 seconds Misc :0.001665889 seconds Base State :8.899996828e-08 seconds Time to advance time step: 0.035390848 Call to estdt for level 0 gives dt_lev = 1.065046887e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 41 gives dt =1e+20 dt_growth factor limits the new dt = 0.01342812062  Timestep 41 starts with TIME = 0.2304142812 DT = 0.01342812062 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.863121796e-29 MLMG: Initial residual (resid0) = 1.863121796e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.751491358e-39, 9.400841973e-11 MLMG: Timers: Solve = 0.005436947 Iter = 0.005219527 Bottom = 0.000123452 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.863121796e-29 MLMG: Initial residual (resid0) = 1.751491358e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022492 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.728435499e-19 MLMG: Initial residual (resid0) = 7.728435499e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.369865821e-29, 1.772500814e-11 MLMG: Timers: Solve = 0.006958375 Iter = 0.006752436 Bottom = 0.000217495 Done calling nodal solver Timestep 41 ends with TIME = 0.2438424018 DT = 0.01342812062 Timing summary: Advection :0.006477143 seconds MAC Proj :0.00638989 seconds Nodal Proj :0.007787764 seconds Reactions :0.012404891 seconds Misc :0.001483583 seconds Base State :3.700006346e-08 seconds Time to advance time step: 0.034685607 Call to estdt for level 0 gives dt_lev = 1.015209966e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 42 gives dt =1e+20 dt_growth factor limits the new dt = 0.01409952665  Timestep 42 starts with TIME = 0.2438424018 DT = 0.01409952665 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.957437553e-29 MLMG: Initial residual (resid0) = 1.957437553e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.839212642e-39, 9.396022058e-11 MLMG: Timers: Solve = 0.005437127 Iter = 0.005222695 Bottom = 0.000120418 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.957437553e-29 MLMG: Initial residual (resid0) = 1.839212642e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000217553 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.114857274e-19 MLMG: Initial residual (resid0) = 8.114857274e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.438294112e-29, 1.772420714e-11 MLMG: Timers: Solve = 0.006955596 Iter = 0.006756559 Bottom = 0.000218115 Done calling nodal solver Timestep 42 ends with TIME = 0.2579419285 DT = 0.01409952665 Timing summary: Advection :0.006412233 seconds MAC Proj :0.006376875 seconds Nodal Proj :0.007789334 seconds Reactions :0.01227579 seconds Misc :0.001494092 seconds Base State :3.800005288e-08 seconds Time to advance time step: 0.03448325 Call to estdt for level 0 gives dt_lev = 9.673808914e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 43 gives dt =1e+20 dt_growth factor limits the new dt = 0.01480450298  Timestep 43 starts with TIME = 0.2579419285 DT = 0.01480450298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.055305455e-29 MLMG: Initial residual (resid0) = 2.055305455e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.931045336e-39, 9.395417752e-11 MLMG: Timers: Solve = 0.005509092 Iter = 0.005256997 Bottom = 0.000120926 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.055305455e-29 MLMG: Initial residual (resid0) = 1.931045336e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022779 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.520600138e-19 MLMG: Initial residual (resid0) = 8.520600138e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.510256484e-29, 1.772476657e-11 MLMG: Timers: Solve = 0.006961181 Iter = 0.006760287 Bottom = 0.000214375 Done calling nodal solver Timestep 43 ends with TIME = 0.2727464314 DT = 0.01480450298 Timing summary: Advection :0.006485324 seconds MAC Proj :0.006461152 seconds Nodal Proj :0.007814229 seconds Reactions :0.012382706 seconds Misc :0.001524916 seconds Base State :3.600007403e-08 seconds Time to advance time step: 0.034808411 Call to estdt for level 0 gives dt_lev = 9.21627116e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 44 gives dt =1e+20 dt_growth factor limits the new dt = 0.01554472813  Timestep 44 starts with TIME = 0.2727464314 DT = 0.01554472813 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.158165969e-29 MLMG: Initial residual (resid0) = 2.158165969e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.027690088e-39, 9.395431664e-11 MLMG: Timers: Solve = 0.005477182 Iter = 0.005259901 Bottom = 0.000120781 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.158165969e-29 MLMG: Initial residual (resid0) = 2.027690088e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000229161 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.946630145e-19 MLMG: Initial residual (resid0) = 8.946630145e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.585743309e-29, 1.772447595e-11 MLMG: Timers: Solve = 0.007057726 Iter = 0.006856914 Bottom = 0.000226203 Done calling nodal solver Timestep 44 ends with TIME = 0.2882911596 DT = 0.01554472813 Timing summary: Advection :0.006493377 seconds MAC Proj :0.006448462 seconds Nodal Proj :0.007904289 seconds Reactions :0.01226457 seconds Misc :0.001495335 seconds Base State :3.699994977e-08 seconds Time to advance time step: 0.034740509 Call to estdt for level 0 gives dt_lev = 8.779254781e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 45 gives dt =1e+20 dt_growth factor limits the new dt = 0.01632196453  Timestep 45 starts with TIME = 0.2882911596 DT = 0.01632196453 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.2662186e-29 MLMG: Initial residual (resid0) = 2.2662186e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.128830206e-39, 9.393754894e-11 MLMG: Timers: Solve = 0.005425962 Iter = 0.005207933 Bottom = 0.00012035 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.2662186e-29 MLMG: Initial residual (resid0) = 2.128830206e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000227188 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.053842861e-18 MLMG: Initial residual (resid0) = 1.053842861e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 6.68124357e-29, 6.339885971e-11 MLMG: Timers: Solve = 0.006995642 Iter = 0.006781089 Bottom = 0.000218966 Done calling nodal solver Timestep 45 ends with TIME = 0.3046131241 DT = 0.01632196453 Timing summary: Advection :0.006603925 seconds MAC Proj :0.006378669 seconds Nodal Proj :0.007846004 seconds Reactions :0.012837958 seconds Misc :0.001492423 seconds Base State :4.300000001e-08 seconds Time to advance time step: 0.035293938 Call to estdt for level 0 gives dt_lev = 2.027437947e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 46 gives dt =1e+20 dt_growth factor limits the new dt = 0.01713806276  Timestep 46 starts with TIME = 0.3046131241 DT = 0.01713806276 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 7.013230718e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.387375708e-30, 4.829978999e-11 MLMG: Timers: Solve = 0.005479001 Iter = 0.005254956 Bottom = 0.000138118 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 3.387375708e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000225385 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 9.863659735e-19 MLMG: Initial residual (resid0) = 9.863659735e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.748282166e-29, 1.772447766e-11 MLMG: Timers: Solve = 0.006995762 Iter = 0.006768386 Bottom = 0.000224492 Done calling nodal solver Timestep 46 ends with TIME = 0.3217511869 DT = 0.01713806276 Timing summary: Advection :0.006342326 seconds MAC Proj :0.006438588 seconds Nodal Proj :0.007866982 seconds Reactions :0.013695067 seconds Misc :0.001491224 seconds Base State :9.600000794e-08 seconds Time to advance time step: 0.035962236 Call to estdt for level 0 gives dt_lev = 7.924349732e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 47 gives dt =1e+20 dt_growth factor limits the new dt = 0.0179949659  Timestep 47 starts with TIME = 0.3217511869 DT = 0.0179949659 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.807872089e-29 MLMG: Initial residual (resid0) = 1.807872089e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.373027268e-39, 7.59471467e-11 MLMG: Timers: Solve = 0.005464562 Iter = 0.005244458 Bottom = 0.000121282 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.807872089e-29 MLMG: Initial residual (resid0) = 1.373027268e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00021704 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.035684272e-18 MLMG: Initial residual (resid0) = 1.035684272e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.835709756e-29, 1.772460783e-11 MLMG: Timers: Solve = 0.007029295 Iter = 0.006809153 Bottom = 0.000242092 Done calling nodal solver Timestep 47 ends with TIME = 0.3397461528 DT = 0.0179949659 Timing summary: Advection :0.006551868 seconds MAC Proj :0.006384405 seconds Nodal Proj :0.007906591 seconds Reactions :0.012946731 seconds Misc :0.001663139 seconds Base State :4.300000001e-08 seconds Time to advance time step: 0.035593903 Call to estdt for level 0 gives dt_lev = 7.566055076e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 48 gives dt =1e+20 dt_growth factor limits the new dt = 0.01889471419  Timestep 48 starts with TIME = 0.3397461528 DT = 0.01889471419 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.590316044e-29 MLMG: Initial residual (resid0) = 2.590316044e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.464404755e-39, 9.51391534e-11 MLMG: Timers: Solve = 0.005466123 Iter = 0.005249681 Bottom = 0.000121295 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.590316044e-29 MLMG: Initial residual (resid0) = 2.464404755e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000217529 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.087468486e-18 MLMG: Initial residual (resid0) = 1.087468486e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.927489948e-29, 1.772455913e-11 MLMG: Timers: Solve = 0.007015196 Iter = 0.006797635 Bottom = 0.000215749 Done calling nodal solver Timestep 48 ends with TIME = 0.358640867 DT = 0.01889471419 Timing summary: Advection :0.006556753 seconds MAC Proj :0.006419184 seconds Nodal Proj :0.007854051 seconds Reactions :0.012310692 seconds Misc :0.001484373 seconds Base State :3.500008461e-08 seconds Time to advance time step: 0.034768283 Call to estdt for level 0 gives dt_lev = 7.214097476e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 49 gives dt =1e+20 dt_growth factor limits the new dt = 0.0198394499  Timestep 49 starts with TIME = 0.358640867 DT = 0.0198394499 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.753899991e-29 MLMG: Initial residual (resid0) = 2.753899991e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.587581692e-39, 9.396062678e-11 MLMG: Timers: Solve = 0.005528833 Iter = 0.005316531 Bottom = 0.000121052 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.753899991e-29 MLMG: Initial residual (resid0) = 2.587570482e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000220518 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.086359695e-18 MLMG: Initial residual (resid0) = 1.086359695e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 4.01595875e-29, 3.696711842e-11 MLMG: Timers: Solve = 0.007002127 Iter = 0.006795232 Bottom = 0.000220773 Done calling nodal solver Timestep 49 ends with TIME = 0.3784803169 DT = 0.0198394499 Timing summary: Advection :0.006553874 seconds MAC Proj :0.00646648 seconds Nodal Proj :0.007868586 seconds Reactions :0.012481143 seconds Misc :0.001486748 seconds Base State :4.300000001e-08 seconds Time to advance time step: 0.03500543 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 50 gives dt =1e+20 dt_growth factor limits the new dt = 0.0208314224  Timestep 50 starts with TIME = 0.3784803169 DT = 0.0208314224 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 8.242756114e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.781214371e-30, 4.587318027e-11 MLMG: Timers: Solve = 0.005531451 Iter = 0.005307552 Bottom = 0.000120497 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 3.781214371e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.00021815 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.198934006e-18 MLMG: Initial residual (resid0) = 1.198934006e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 2.125061471e-29, 1.772459085e-11 MLMG: Timers: Solve = 0.006980736 Iter = 0.006765168 Bottom = 0.00021532 Done calling nodal solver Timestep 50 ends with TIME = 0.3993117393 DT = 0.0208314224 Timing summary: Advection :0.006273792 seconds MAC Proj :0.006464759 seconds Nodal Proj :0.007838998 seconds Reactions :0.012409445 seconds Misc :0.001496505 seconds Base State :3.600007403e-08 seconds Time to advance time step: 0.03461118 Writing plotfile 50 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.060625294 Writing checkpoint 50 Writing checkpoint chk0000050 Total Time: 3.383125137 Unused ParmParse Variables: [TOP]::amr.check_file(nvals = 1) :: [test_stability_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] AMReX (25.01-3-g3a34576c9930) finalized