Initializing AMReX (25.11-20-ga7f0aed21606)... MPI initialized with 16 MPI processes MPI initialized with thread support level 0 AMReX (25.11-20-ga7f0aed21606) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = 5peaks_const_grav.dat model file = 5peaks_const_grav.dat reading initial model 1000 points found in the initial model 10 variables found in the initial model WARNING: variable not found: gravity WARNING: variable not found: abar WARNING: variable not found: zbar WARNING: variable not found: gpot WARNING: variable not found: cno model file mapping, level: 0 dr of MAESTRO base state = 93750000.000000 dr of input file data = 10010010.010010 maximum radius (cell-centered) of input model = 10000000000.000000 WARNING: resolution of base state array is not an integer multiple of the initial model's resolution. make sure this is a desired property as this could lead to aliasing when performing the interpolation. modulus = 3659909.909910 setting r_cutoff to 105 radius at r_cutoff 9890625000 Maximum HSE Error = 0.054171 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile test_stability_pltInitData after InitData inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.016534885 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.000347052 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile test_stability_pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.014284476 Call to firstdt for level 0 gives dt_lev = 0.01907406555 Multiplying dt_lev by init_shrink; dt_lev = 0.001907406555 Minimum firstdt over all levels = 0.001907406555 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 4.945354899e-27 MLMG: Initial residual (resid0) = 4.945354899e-27 MLMG: Final Iter. 3 resid, resid/bnorm = 2.357566962e-30, 0.0004767235133 MLMG: Timers: Solve = 0.002706586 Iter = 0.002469361 Bottom = 4.7902e-05 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 1 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #2 Calling nodal solver MLMG: Initial rhs = 2.306075226e-30 MLMG: Initial residual (resid0) = 2.306075226e-30 MLMG: Final Iter. 5 resid, resid/bnorm = 1.933642558e-37, 8.384993415e-08 MLMG: Timers: Solve = 0.003875915 Iter = 0.003645325 Bottom = 7.0038e-05 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 2 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #3 Calling nodal solver MLMG: Initial rhs = 9.742172194e-32 MLMG: Initial residual (resid0) = 9.742172194e-32 MLMG: Final Iter. 4 resid, resid/bnorm = 7.56277059e-41, 7.76292026e-10 MLMG: Timers: Solve = 0.003383742 Iter = 0.003125464 Bottom = 6.0089e-05 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 3 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Writing plotfile test_stability_pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.012614325 Doing initial pressure iteration #1  Timestep 0 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.893547601e-20 MLMG: Initial residual (resid0) = 4.893547601e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 4.517319639e-31, 9.231175431e-12 MLMG: Timers: Solve = 0.004944763 Iter = 0.004661237 Bottom = 0.000116484 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.893547507e-20 MLMG: Initial residual (resid0) = 2.477484298e-27 MLMG: Final Iter. 4 resid, resid/bnorm = 4.813594317e-30, 9.836615074e-11 MLMG: Timers: Solve = 0.002185833 Iter = 0.001953835 Bottom = 6.3071e-05 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.755411273e-17 MLMG: Initial residual (resid0) = 5.755411273e-17 MLMG: Final Iter. 9 resid, resid/bnorm = 1.020114247e-27, 1.772443703e-11 MLMG: Timers: Solve = 0.006473017 Iter = 0.006277463 Bottom = 0.000137428 Done calling nodal solver Timestep 0 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.006008039 seconds MAC Proj :0.00798703 seconds Nodal Proj :0.007209561 seconds Reactions :0.012439574 seconds Misc :0.001397788 seconds Base State :4.500009254e-08 seconds Time to advance time step: 0.038322119 Writing plotfile 0 after all initialization inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.012852305 Writing checkpoint 0 after all initialization Writing checkpoint chk0000000 Beginning main evolution  Timestep 1 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.257776132e-26 MLMG: Initial residual (resid0) = 1.257776132e-26 MLMG: Final Iter. 10 resid, resid/bnorm = 1.092354528e-37, 8.684808849e-12 MLMG: Timers: Solve = 0.004964468 Iter = 0.004723912 Bottom = 0.000121002 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.257776132e-26 MLMG: Initial residual (resid0) = 1.092354528e-37 MLMG: No iterations needed MLMG: Timers: Solve = 0.000245014 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.097790919e-19 MLMG: Initial residual (resid0) = 1.097790919e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.945791097e-30, 1.772460551e-11 MLMG: Timers: Solve = 0.006453956 Iter = 0.006234829 Bottom = 0.000127345 Done calling nodal solver Timestep 1 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.006070076 seconds MAC Proj :0.00592276 seconds Nodal Proj :0.00719125 seconds Reactions :0.012097527 seconds Misc :0.001535376 seconds Base State :6.100003702e-08 seconds Time to advance time step: 0.037817156 Call to estdt for level 0 gives dt_lev = 7.191087425e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 2 gives dt =1e+20 dt_growth factor limits the new dt = 0.002002776883  Timestep 2 starts with TIME = 0.001907406555 DT = 0.002002776883 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.08039884e-27 MLMG: Initial residual (resid0) = 8.08039884e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 1.160384542e-37, 1.436048597e-11 MLMG: Timers: Solve = 0.004805837 Iter = 0.004600995 Bottom = 0.000114525 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.498306041e-27 MLMG: Initial residual (resid0) = 2.601349809e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 8.687490856e-37, 9.146358118e-11 MLMG: Timers: Solve = 0.005179912 Iter = 0.004966267 Bottom = 0.000114934 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.096671578e-19 MLMG: Initial residual (resid0) = 1.096671578e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.008841827e-29, 9.199124398e-11 MLMG: Timers: Solve = 0.006341982 Iter = 0.00616517 Bottom = 0.000134576 Done calling nodal solver Timestep 2 ends with TIME = 0.003910183437 DT = 0.002002776883 Timing summary: Advection :0.005931839 seconds MAC Proj :0.010739411 seconds Nodal Proj :0.007132277 seconds Reactions :0.012709545 seconds Misc :0.001365882 seconds Base State :5.200001851e-08 seconds Time to advance time step: 0.038059131 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 3 gives dt =1e+20 dt_growth factor limits the new dt = 0.002102915727  Timestep 3 starts with TIME = 0.003910183437 DT = 0.002102915727 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 8.320997544e-21 MLMG: Final Iter. 10 resid, resid/bnorm = 7.677524121e-31, 9.226687161e-11 MLMG: Timers: Solve = 0.004748032 Iter = 0.004514214 Bottom = 0.000111564 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 7.677524121e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000205256 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.21031446e-19 MLMG: Initial residual (resid0) = 1.21031446e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.145245217e-30, 1.772469294e-11 MLMG: Timers: Solve = 0.006397186 Iter = 0.006189786 Bottom = 0.000125316 Done calling nodal solver Timestep 3 ends with TIME = 0.006013099164 DT = 0.002102915727 Timing summary: Advection :0.006184783 seconds MAC Proj :0.005722526 seconds Nodal Proj :0.007376977 seconds Reactions :0.01845562 seconds Misc :0.001479379 seconds Base State :2.640000503e-07 seconds Time to advance time step: 0.040233988 Call to estdt for level 0 gives dt_lev = 6.528670715e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 4 gives dt =1e+20 dt_growth factor limits the new dt = 0.002208061513  Timestep 4 starts with TIME = 0.006013099164 DT = 0.002208061513 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.3079729e-29 MLMG: Initial residual (resid0) = 1.3079729e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.129684783e-39, 8.63691276e-11 MLMG: Timers: Solve = 0.004767239 Iter = 0.004543889 Bottom = 0.000116834 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.3079729e-29 MLMG: Initial residual (resid0) = 1.129684783e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00021291 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.270830183e-19 MLMG: Initial residual (resid0) = 1.270830183e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.252519515e-30, 1.772478766e-11 MLMG: Timers: Solve = 0.013408868 Iter = 0.013242867 Bottom = 0.000140468 Done calling nodal solver Timestep 4 ends with TIME = 0.008221160677 DT = 0.002208061513 Timing summary: Advection :0.005909558 seconds MAC Proj :0.005706015 seconds Nodal Proj :0.014224066 seconds Reactions :0.011940004 seconds Misc :0.001577238 seconds Base State :9.600000794e-08 seconds Time to advance time step: 0.03954019 Call to estdt for level 0 gives dt_lev = 6.226377027e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 5 gives dt =1e+20 dt_growth factor limits the new dt = 0.002318464589  Timestep 5 starts with TIME = 0.008221160677 DT = 0.002318464589 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.295423824e-30 MLMG: Initial residual (resid0) = 3.295423824e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.024461011e-40, 9.177760352e-11 MLMG: Timers: Solve = 0.009109367 Iter = 0.008880359 Bottom = 0.000116987 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.295423824e-30 MLMG: Initial residual (resid0) = 3.024461011e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000457996 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.334371692e-19 MLMG: Initial residual (resid0) = 1.334371692e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.365126231e-30, 1.772464333e-11 MLMG: Timers: Solve = 0.006465926 Iter = 0.006189144 Bottom = 0.000152858 Done calling nodal solver Timestep 5 ends with TIME = 0.01053962527 DT = 0.002318464589 Timing summary: Advection :0.0064118 seconds MAC Proj :0.010424881 seconds Nodal Proj :0.007424215 seconds Reactions :0.018011979 seconds Misc :0.00214437 seconds Base State :8.299991805e-08 seconds Time to advance time step: 0.044645586 Call to estdt for level 0 gives dt_lev = 5.914991835e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 6 gives dt =1e+20 dt_growth factor limits the new dt = 0.002434387818  Timestep 6 starts with TIME = 0.01053962527 DT = 0.002434387818 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.377300377e-30 MLMG: Initial residual (resid0) = 3.377300377e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.175447418e-40, 9.402324529e-11 MLMG: Timers: Solve = 0.00477194 Iter = 0.00455306 Bottom = 0.000129475 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.377300377e-30 MLMG: Initial residual (resid0) = 3.175443914e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000210961 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.401090277e-19 MLMG: Initial residual (resid0) = 1.401090277e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.483390367e-30, 1.772469917e-11 MLMG: Timers: Solve = 0.01408395 Iter = 0.013915911 Bottom = 0.000127035 Done calling nodal solver Timestep 6 ends with TIME = 0.01297401308 DT = 0.002434387818 Timing summary: Advection :0.006005529 seconds MAC Proj :0.005658508 seconds Nodal Proj :0.014973506 seconds Reactions :0.011821896 seconds Misc :0.001553306 seconds Base State :7.500000265e-08 seconds Time to advance time step: 0.04019869 Call to estdt for level 0 gives dt_lev = 5.625582499e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 7 gives dt =1e+20 dt_growth factor limits the new dt = 0.002556107209  Timestep 7 starts with TIME = 0.01297401308 DT = 0.002556107209 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.542867857e-30 MLMG: Initial residual (resid0) = 3.542867857e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.33382217e-40, 9.409953474e-11 MLMG: Timers: Solve = 0.004707396 Iter = 0.004501619 Bottom = 0.000114009 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.542867857e-30 MLMG: Initial residual (resid0) = 3.33382217e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000214537 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.471144791e-19 MLMG: Initial residual (resid0) = 1.471144791e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.607576737e-30, 1.772481372e-11 MLMG: Timers: Solve = 0.006241239 Iter = 0.006050236 Bottom = 0.000123817 Done calling nodal solver Timestep 7 ends with TIME = 0.01553012029 DT = 0.002556107209 Timing summary: Advection :0.006050885 seconds MAC Proj :0.005670117 seconds Nodal Proj :0.006983989 seconds Reactions :0.012044756 seconds Misc :0.001561412 seconds Base State :7.799997093e-08 seconds Time to advance time step: 0.032478445 Call to estdt for level 0 gives dt_lev = 5.353302437e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 8 gives dt =1e+20 dt_growth factor limits the new dt = 0.002683912569  Timestep 8 starts with TIME = 0.01553012029 DT = 0.002683912569 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.719890133e-30 MLMG: Initial residual (resid0) = 3.719890133e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.500289421e-40, 9.409658071e-11 MLMG: Timers: Solve = 0.004822478 Iter = 0.004553634 Bottom = 0.000118482 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.719890133e-30 MLMG: Initial residual (resid0) = 3.500289421e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000208343 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.54470203e-19 MLMG: Initial residual (resid0) = 1.54470203e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.737926083e-30, 1.77246228e-11 MLMG: Timers: Solve = 0.00627696 Iter = 0.006097841 Bottom = 0.000161062 Done calling nodal solver Timestep 8 ends with TIME = 0.01821403286 DT = 0.002683912569 Timing summary: Advection :0.012983694 seconds MAC Proj :0.005818174 seconds Nodal Proj :0.007091302 seconds Reactions :0.012164952 seconds Misc :0.001504419 seconds Base State :8.300003174e-08 seconds Time to advance time step: 0.039778055 Call to estdt for level 0 gives dt_lev = 5.095587997e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 9 gives dt =1e+20 dt_growth factor limits the new dt = 0.002818108198  Timestep 9 starts with TIME = 0.01821403286 DT = 0.002818108198 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.905661102e-30 MLMG: Initial residual (resid0) = 3.905661102e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.676397606e-40, 9.412996953e-11 MLMG: Timers: Solve = 0.004811204 Iter = 0.004552198 Bottom = 0.000132564 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.905661102e-30 MLMG: Initial residual (resid0) = 3.676397606e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000207623 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.621937132e-19 MLMG: Initial residual (resid0) = 1.621937132e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.874823591e-30, 1.772463022e-11 MLMG: Timers: Solve = 0.006388696 Iter = 0.006212842 Bottom = 0.000122715 Done calling nodal solver Timestep 9 ends with TIME = 0.02103214106 DT = 0.002818108198 Timing summary: Advection :0.005990019 seconds MAC Proj :0.00567127 seconds Nodal Proj :0.007195629 seconds Reactions :0.012623543 seconds Misc :0.001654757 seconds Base State :8.299991805e-08 seconds Time to advance time step: 0.033316908 Call to estdt for level 0 gives dt_lev = 4.851262359e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 10 gives dt =1e+20 dt_growth factor limits the new dt = 0.002959013608  Timestep 10 starts with TIME = 0.02103214106 DT = 0.002959013608 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.100939546e-30 MLMG: Initial residual (resid0) = 4.100939546e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.860100828e-40, 9.412723071e-11 MLMG: Timers: Solve = 0.004693069 Iter = 0.004491336 Bottom = 0.000116249 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.100939546e-30 MLMG: Initial residual (resid0) = 3.860100828e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000220487 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.703033988e-19 MLMG: Initial residual (resid0) = 1.703033988e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.174813655e-29, 6.898357067e-11 MLMG: Timers: Solve = 0.006342916 Iter = 0.006138845 Bottom = 0.000126072 Done calling nodal solver Timestep 10 ends with TIME = 0.02399115467 DT = 0.002959013608 Timing summary: Advection :0.006487768 seconds MAC Proj :0.005605759 seconds Nodal Proj :0.007109557 seconds Reactions :0.012319956 seconds Misc :0.001405051 seconds Base State :8.200004231e-08 seconds Time to advance time step: 0.033089804 Call to estdt for level 0 gives dt_lev = 1.153494089e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 11 gives dt =1e+20 dt_growth factor limits the new dt = 0.003106964288  Timestep 11 starts with TIME = 0.02399115467 DT = 0.003106964288 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 1.271430598e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.310351499e-31, 4.963189897e-11 MLMG: Timers: Solve = 0.004732617 Iter = 0.004521628 Bottom = 0.000119456 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 6.310351499e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000233562 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.788185688e-19 MLMG: Initial residual (resid0) = 1.788185688e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.169478835e-30, 1.772455096e-11 MLMG: Timers: Solve = 0.006342711 Iter = 0.006131672 Bottom = 0.000124512 Done calling nodal solver Timestep 11 ends with TIME = 0.02709811896 DT = 0.003106964288 Timing summary: Advection :0.00567753 seconds MAC Proj :0.005665427 seconds Nodal Proj :0.007099754 seconds Reactions :0.011919774 seconds Misc :0.001391447 seconds Base State :8.400002116e-08 seconds Time to advance time step: 0.031930554 Call to estdt for level 0 gives dt_lev = 4.376646045e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 12 gives dt =1e+20 dt_growth factor limits the new dt = 0.003262312503  Timestep 12 starts with TIME = 0.02709811896 DT = 0.003262312503 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.931087603e-30 MLMG: Initial residual (resid0) = 2.931087603e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.211756947e-40, 7.545857536e-11 MLMG: Timers: Solve = 0.004748732 Iter = 0.004539606 Bottom = 0.000116554 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.931087603e-30 MLMG: Initial residual (resid0) = 2.211756947e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000207077 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.877594972e-19 MLMG: Initial residual (resid0) = 1.877594972e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.327886573e-30, 1.772419836e-11 MLMG: Timers: Solve = 0.006307329 Iter = 0.006121275 Bottom = 0.00015997 Done calling nodal solver Timestep 12 ends with TIME = 0.03036043146 DT = 0.003262312503 Timing summary: Advection :0.005890036 seconds MAC Proj :0.00570395 seconds Nodal Proj :0.007077525 seconds Reactions :0.011847513 seconds Misc :0.001377729 seconds Base State :9.099994713e-08 seconds Time to advance time step: 0.03206593 Call to estdt for level 0 gives dt_lev = 4.177453783e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 13 gives dt =1e+20 dt_growth factor limits the new dt = 0.003425428128  Timestep 13 starts with TIME = 0.03036043146 DT = 0.003425428128 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.688248856e-30 MLMG: Initial residual (resid0) = 4.688248856e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.467598744e-40, 9.52935495e-11 MLMG: Timers: Solve = 0.004779221 Iter = 0.004570893 Bottom = 0.000124831 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.688248856e-30 MLMG: Initial residual (resid0) = 4.467598744e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000220795 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.971474721e-19 MLMG: Initial residual (resid0) = 1.971474721e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.494310995e-30, 1.7724351e-11 MLMG: Timers: Solve = 0.006323075 Iter = 0.006125821 Bottom = 0.000125603 Done calling nodal solver Timestep 13 ends with TIME = 0.03378585959 DT = 0.003425428128 Timing summary: Advection :0.005858714 seconds MAC Proj :0.005670896 seconds Nodal Proj :0.007073509 seconds Reactions :0.013506388 seconds Misc :0.001379292 seconds Base State :5.399999736e-08 seconds Time to advance time step: 0.033641367 Call to estdt for level 0 gives dt_lev = 3.982247017e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 14 gives dt =1e+20 dt_growth factor limits the new dt = 0.003596699534  Timestep 14 starts with TIME = 0.03378585959 DT = 0.003596699534 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.98227213e-30 MLMG: Initial residual (resid0) = 4.98227213e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.691855544e-40, 9.417100114e-11 MLMG: Timers: Solve = 0.004823268 Iter = 0.004616476 Bottom = 0.000122874 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.98227213e-30 MLMG: Initial residual (resid0) = 4.691855544e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00020854 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.221658729e-19 MLMG: Initial residual (resid0) = 2.221658729e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.863225901e-30, 3.989463271e-11 MLMG: Timers: Solve = 0.006255501 Iter = 0.006081145 Bottom = 0.000123855 Done calling nodal solver Timestep 14 ends with TIME = 0.03738255912 DT = 0.003596699534 Timing summary: Advection :0.005978513 seconds MAC Proj :0.005767327 seconds Nodal Proj :0.006987436 seconds Reactions :0.011978612 seconds Misc :0.001394306 seconds Base State :9.300003967e-08 seconds Time to advance time step: 0.032272517 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 15 gives dt =1e+20 dt_growth factor limits the new dt = 0.003776534511  Timestep 15 starts with TIME = 0.03738255912 DT = 0.003776534511 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 1.44706648e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 8.546351457e-31, 5.905983986e-11 MLMG: Timers: Solve = 0.004729798 Iter = 0.004519421 Bottom = 0.000117194 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 8.546351457e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000258935 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.279163939e-19 MLMG: Initial residual (resid0) = 2.279163939e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.500913317e-29, 6.585367956e-11 MLMG: Timers: Solve = 0.006323682 Iter = 0.006147123 Bottom = 0.000123756 Done calling nodal solver Timestep 15 ends with TIME = 0.04115909363 DT = 0.003776534511 Timing summary: Advection :0.006183319 seconds MAC Proj :0.005700498 seconds Nodal Proj :0.007125712 seconds Reactions :0.012026948 seconds Misc :0.001397411 seconds Base State :8.799997886e-08 seconds Time to advance time step: 0.032599907 Call to estdt for level 0 gives dt_lev = 9.044183602e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 16 gives dt =1e+20 dt_growth factor limits the new dt = 0.003965361236  Timestep 16 starts with TIME = 0.04115909363 DT = 0.003965361236 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 1.62270343e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.18605137e-31, 3.812188509e-11 MLMG: Timers: Solve = 0.004736291 Iter = 0.004519268 Bottom = 0.000114934 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 6.18605137e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000235808 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.282228424e-19 MLMG: Initial residual (resid0) = 2.282228424e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.045223255e-30, 1.772488333e-11 MLMG: Timers: Solve = 0.006287464 Iter = 0.006095962 Bottom = 0.000122223 Done calling nodal solver Timestep 16 ends with TIME = 0.04512445487 DT = 0.003965361236 Timing summary: Advection :0.005659692 seconds MAC Proj :0.005650608 seconds Nodal Proj :0.007047093 seconds Reactions :0.012571671 seconds Misc :0.001380275 seconds Base State :7.599999208e-08 seconds Time to advance time step: 0.032472321 Call to estdt for level 0 gives dt_lev = 3.436635199e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 17 gives dt =1e+20 dt_growth factor limits the new dt = 0.004163629298  Timestep 17 starts with TIME = 0.04512445487 DT = 0.004163629298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.754712132e-30 MLMG: Initial residual (resid0) = 3.754712132e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.82584447e-40, 7.526128158e-11 MLMG: Timers: Solve = 0.0047395 Iter = 0.00453835 Bottom = 0.00011945 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.754712132e-30 MLMG: Initial residual (resid0) = 2.82584447e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000211357 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.396339845e-19 MLMG: Initial residual (resid0) = 2.396339845e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.247421825e-30, 1.772462213e-11 MLMG: Timers: Solve = 0.006618631 Iter = 0.006420045 Bottom = 0.000127676 Done calling nodal solver Timestep 17 ends with TIME = 0.04928808417 DT = 0.004163629298 Timing summary: Advection :0.005917505 seconds MAC Proj :0.005638694 seconds Nodal Proj :0.00740881 seconds Reactions :0.011800215 seconds Misc :0.001377482 seconds Base State :8.200004231e-08 seconds Time to advance time step: 0.032321801 Call to estdt for level 0 gives dt_lev = 3.276873657e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 18 gives dt =1e+20 dt_growth factor limits the new dt = 0.004371810763  Timestep 18 starts with TIME = 0.04928808417 DT = 0.004371810763 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.988437125e-30 MLMG: Initial residual (resid0) = 5.988437125e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.701673257e-40, 9.521137381e-11 MLMG: Timers: Solve = 0.004745249 Iter = 0.004537008 Bottom = 0.000115037 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.988437125e-30 MLMG: Initial residual (resid0) = 5.701673257e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000286313 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.516156837e-19 MLMG: Initial residual (resid0) = 2.516156837e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.459779676e-30, 1.772456951e-11 MLMG: Timers: Solve = 0.006263073 Iter = 0.006086411 Bottom = 0.000124998 Done calling nodal solver Timestep 18 ends with TIME = 0.05365989493 DT = 0.004371810763 Timing summary: Advection :0.006319021 seconds MAC Proj :0.005810043 seconds Nodal Proj :0.007036181 seconds Reactions :0.012154721 seconds Misc :0.001368681 seconds Base State :7.700009519e-08 seconds Time to advance time step: 0.032846642 Call to estdt for level 0 gives dt_lev = 3.122293372e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 19 gives dt =1e+20 dt_growth factor limits the new dt = 0.004590401301  Timestep 19 starts with TIME = 0.05365989493 DT = 0.004590401301 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.361637466e-30 MLMG: Initial residual (resid0) = 6.361637466e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.987748338e-40, 9.41227533e-11 MLMG: Timers: Solve = 0.004885337 Iter = 0.004679466 Bottom = 0.000114925 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.361637466e-30 MLMG: Initial residual (resid0) = 5.987748338e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000219697 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.641964679e-19 MLMG: Initial residual (resid0) = 2.641964679e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.68289866e-30, 1.772506157e-11 MLMG: Timers: Solve = 0.00667237 Iter = 0.006351437 Bottom = 0.000151827 Done calling nodal solver Timestep 19 ends with TIME = 0.05825029623 DT = 0.004590401301 Timing summary: Advection :0.006081644 seconds MAC Proj :0.005807635 seconds Nodal Proj :0.007454263 seconds Reactions :0.011911429 seconds Misc :0.00137069 seconds Base State :2.599999789e-07 seconds Time to advance time step: 0.032780163 Call to estdt for level 0 gives dt_lev = 2.974235616e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 20 gives dt =1e+20 dt_growth factor limits the new dt = 0.004819921366  Timestep 20 starts with TIME = 0.05825029623 DT = 0.004819921366 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.682786498e-30 MLMG: Initial residual (resid0) = 6.682786498e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.287114735e-40, 9.407923982e-11 MLMG: Timers: Solve = 0.004759067 Iter = 0.004551304 Bottom = 0.000114144 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.682786498e-30 MLMG: Initial residual (resid0) = 6.287114735e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000218221 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.774062913e-19 MLMG: Initial residual (resid0) = 2.774062913e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.916875074e-30, 1.772445409e-11 MLMG: Timers: Solve = 0.006274808 Iter = 0.006099665 Bottom = 0.000125215 Done calling nodal solver Timestep 20 ends with TIME = 0.0630702176 DT = 0.004819921366 Timing summary: Advection :0.005944605 seconds MAC Proj :0.005695212 seconds Nodal Proj :0.0070371 seconds Reactions :0.012389218 seconds Misc :0.001538253 seconds Base State :1.689999181e-07 seconds Time to advance time step: 0.032782484 Call to estdt for level 0 gives dt_lev = 2.832901245e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 21 gives dt =1e+20 dt_growth factor limits the new dt = 0.005060917435  Timestep 21 starts with TIME = 0.0630702176 DT = 0.005060917435 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.017767486e-30 MLMG: Initial residual (resid0) = 7.017767486e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.601040624e-40, 9.406183144e-11 MLMG: Timers: Solve = 0.005026799 Iter = 0.004816173 Bottom = 0.000119129 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.017767486e-30 MLMG: Initial residual (resid0) = 6.601040624e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000207589 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.869691725e-19 MLMG: Initial residual (resid0) = 2.869691725e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.297839054e-29, 8.007267937e-11 MLMG: Timers: Solve = 0.006324211 Iter = 0.006112586 Bottom = 0.000122605 Done calling nodal solver Timestep 21 ends with TIME = 0.06813113503 DT = 0.005060917435 Timing summary: Advection :0.006062451 seconds MAC Proj :0.005906266 seconds Nodal Proj :0.007116357 seconds Reactions :0.011902797 seconds Misc :0.001398945 seconds Base State :2.139998969e-07 seconds Time to advance time step: 0.032549451 Call to estdt for level 0 gives dt_lev = 5.895649157e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 22 gives dt =1e+20 dt_growth factor limits the new dt = 0.005313963306  Timestep 22 starts with TIME = 0.06813113503 DT = 0.005313963306 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 2.174577793e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 1.127453232e-30, 5.184699467e-11 MLMG: Timers: Solve = 0.004748507 Iter = 0.004514249 Bottom = 0.000113524 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 1.127453232e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000207054 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.058404362e-19 MLMG: Initial residual (resid0) = 3.058404362e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.420842792e-30, 1.772441493e-11 MLMG: Timers: Solve = 0.00659442 Iter = 0.006418561 Bottom = 0.000135194 Done calling nodal solver Timestep 22 ends with TIME = 0.07344509834 DT = 0.005313963306 Timing summary: Advection :0.005741836 seconds MAC Proj :0.005665211 seconds Nodal Proj :0.007369045 seconds Reactions :0.011919994 seconds Misc :0.001407855 seconds Base State :7.69999815e-08 seconds Time to advance time step: 0.032257889 Call to estdt for level 0 gives dt_lev = 2.554660013e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 23 gives dt =1e+20 dt_growth factor limits the new dt = 0.005579661472  Timestep 23 starts with TIME = 0.07344509834 DT = 0.005579661472 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.73348257e-30 MLMG: Initial residual (resid0) = 7.73348257e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.972845529e-40, 7.723358105e-11 MLMG: Timers: Solve = 0.004837853 Iter = 0.004631445 Bottom = 0.000127561 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.73348257e-30 MLMG: Initial residual (resid0) = 5.972845529e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000225813 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.21132458e-19 MLMG: Initial residual (resid0) = 3.21132458e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.691941506e-30, 1.77245911e-11 MLMG: Timers: Solve = 0.006359984 Iter = 0.006181487 Bottom = 0.000124431 Done calling nodal solver Timestep 23 ends with TIME = 0.07902475981 DT = 0.005579661472 Timing summary: Advection :0.005818192 seconds MAC Proj :0.005760837 seconds Nodal Proj :0.007119045 seconds Reactions :0.012590575 seconds Misc :0.001381924 seconds Base State :7.799997093e-08 seconds Time to advance time step: 0.032822351 Call to estdt for level 0 gives dt_lev = 2.439862005e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 24 gives dt =1e+20 dt_growth factor limits the new dt = 0.005858644545  Timestep 24 starts with TIME = 0.07902475981 DT = 0.005858644545 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.00564811e-30 MLMG: Initial residual (resid0) = 8.00564811e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 7.641742954e-40, 9.545439482e-11 MLMG: Timers: Solve = 0.004801207 Iter = 0.004592215 Bottom = 0.000117657 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.00564811e-30 MLMG: Initial residual (resid0) = 7.641742954e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000223565 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.371890809e-19 MLMG: Initial residual (resid0) = 3.371890809e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.976593952e-30, 1.772475531e-11 MLMG: Timers: Solve = 0.006364194 Iter = 0.006173254 Bottom = 0.000125121 Done calling nodal solver Timestep 24 ends with TIME = 0.08488340435 DT = 0.005858644545 Timing summary: Advection :0.005960932 seconds MAC Proj :0.005703267 seconds Nodal Proj :0.007138779 seconds Reactions :0.01188592 seconds Misc :0.001379485 seconds Base State :8.600000001e-08 seconds Time to advance time step: 0.032224308 Call to estdt for level 0 gives dt_lev = 2.326582163e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 25 gives dt =1e+20 dt_growth factor limits the new dt = 0.006151576773  Timestep 25 starts with TIME = 0.08488340435 DT = 0.006151576773 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.527771313e-30 MLMG: Initial residual (resid0) = 8.527771313e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.024857955e-40, 9.410264019e-11 MLMG: Timers: Solve = 0.005150531 Iter = 0.004926772 Bottom = 0.000129136 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.527771313e-30 MLMG: Initial residual (resid0) = 8.024857955e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000227424 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.540485349e-19 MLMG: Initial residual (resid0) = 3.540485349e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.275353834e-30, 1.772455812e-11 MLMG: Timers: Solve = 0.006719069 Iter = 0.006492325 Bottom = 0.000148428 Done calling nodal solver Timestep 25 ends with TIME = 0.09103498113 DT = 0.006151576773 Timing summary: Advection :0.005948554 seconds MAC Proj :0.006142359 seconds Nodal Proj :0.007494522 seconds Reactions :0.011935199 seconds Misc :0.001380695 seconds Base State :8.900008197e-08 seconds Time to advance time step: 0.033068094 Call to estdt for level 0 gives dt_lev = 2.21729507e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 26 gives dt =1e+20 dt_growth factor limits the new dt = 0.006459155611  Timestep 26 starts with TIME = 0.09103498113 DT = 0.006459155611 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.960012316e-30 MLMG: Initial residual (resid0) = 8.960012316e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.424844588e-40, 9.402715411e-11 MLMG: Timers: Solve = 0.004674018 Iter = 0.004463845 Bottom = 0.000129565 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.960012316e-30 MLMG: Initial residual (resid0) = 8.424844588e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000238464 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.717509617e-19 MLMG: Initial residual (resid0) = 3.717509617e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.58913597e-30, 1.772459698e-11 MLMG: Timers: Solve = 0.0063192 Iter = 0.006117422 Bottom = 0.000133309 Done calling nodal solver Timestep 26 ends with TIME = 0.09749413674 DT = 0.006459155611 Timing summary: Advection :0.005965053 seconds MAC Proj :0.005711463 seconds Nodal Proj :0.007078819 seconds Reactions :0.012027347 seconds Misc :0.001381374 seconds Base State :5.300000794e-08 seconds Time to advance time step: 0.032329265 Call to estdt for level 0 gives dt_lev = 2.112511375e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 27 gives dt =1e+20 dt_growth factor limits the new dt = 0.006782113392  Timestep 27 starts with TIME = 0.09749413674 DT = 0.006782113392 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.408830982e-30 MLMG: Initial residual (resid0) = 9.408830982e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.846691478e-40, 9.402540544e-11 MLMG: Timers: Solve = 0.004700606 Iter = 0.004483551 Bottom = 0.000114414 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.408830982e-30 MLMG: Initial residual (resid0) = 8.846691478e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000203833 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.903385097e-19 MLMG: Initial residual (resid0) = 3.903385097e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.918614436e-30, 1.772465248e-11 MLMG: Timers: Solve = 0.006253458 Iter = 0.006072653 Bottom = 0.00012409 Done calling nodal solver Timestep 27 ends with TIME = 0.1042762501 DT = 0.006782113392 Timing summary: Advection :0.005997366 seconds MAC Proj :0.005595454 seconds Nodal Proj :0.006997702 seconds Reactions :0.011916706 seconds Misc :0.00135415 seconds Base State :8.400002116e-08 seconds Time to advance time step: 0.032031821 Call to estdt for level 0 gives dt_lev = 2.0124204e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 28 gives dt =1e+20 dt_growth factor limits the new dt = 0.007121219061  Timestep 28 starts with TIME = 0.1042762501 DT = 0.007121219061 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.880130395e-30 MLMG: Initial residual (resid0) = 9.880130395e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 9.288520884e-40, 9.40121285e-11 MLMG: Timers: Solve = 0.004757274 Iter = 0.004549241 Bottom = 0.000113425 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.880130395e-30 MLMG: Initial residual (resid0) = 9.288520884e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000208143 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.098554352e-19 MLMG: Initial residual (resid0) = 4.098554352e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.264511454e-30, 1.772457025e-11 MLMG: Timers: Solve = 0.006511721 Iter = 0.006337668 Bottom = 0.000120314 Done calling nodal solver Timestep 28 ends with TIME = 0.1113974692 DT = 0.007121219061 Timing summary: Advection :0.006444042 seconds MAC Proj :0.005640653 seconds Nodal Proj :0.007291567 seconds Reactions :0.011968569 seconds Misc :0.001707465 seconds Base State :8.799997886e-08 seconds Time to advance time step: 0.033207802 Call to estdt for level 0 gives dt_lev = 1.916904797e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 29 gives dt =1e+20 dt_growth factor limits the new dt = 0.007477280014  Timestep 29 starts with TIME = 0.1113974692 DT = 0.007477280014 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.037425901e-29 MLMG: Initial residual (resid0) = 1.037425901e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 9.752925208e-40, 9.401081271e-11 MLMG: Timers: Solve = 0.004726247 Iter = 0.004521075 Bottom = 0.000110595 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.037425901e-29 MLMG: Initial residual (resid0) = 9.752925208e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000205581 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.30348207e-19 MLMG: Initial residual (resid0) = 4.30348207e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.627838138e-30, 1.77248052e-11 MLMG: Timers: Solve = 0.006330569 Iter = 0.00613716 Bottom = 0.00013296 Done calling nodal solver Timestep 29 ends with TIME = 0.1188747492 DT = 0.007477280014 Timing summary: Advection :0.005986559 seconds MAC Proj :0.0056188 seconds Nodal Proj :0.007053862 seconds Reactions :0.011945361 seconds Misc :0.001347156 seconds Base State :7.599999208e-08 seconds Time to advance time step: 0.032114668 Call to estdt for level 0 gives dt_lev = 1.825812456e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 30 gives dt =1e+20 dt_growth factor limits the new dt = 0.007851144015  Timestep 30 starts with TIME = 0.1188747492 DT = 0.007851144015 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.08944873e-29 MLMG: Initial residual (resid0) = 1.08944873e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.023977833e-39, 9.399045635e-11 MLMG: Timers: Solve = 0.005129627 Iter = 0.004889234 Bottom = 0.000108917 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.08944873e-29 MLMG: Initial residual (resid0) = 1.023977833e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000276781 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.518656173e-19 MLMG: Initial residual (resid0) = 4.518656173e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.00907597e-30, 1.772446423e-11 MLMG: Timers: Solve = 0.006492753 Iter = 0.006165431 Bottom = 0.000129306 Done calling nodal solver Timestep 30 ends with TIME = 0.1267258932 DT = 0.007851144015 Timing summary: Advection :0.006029303 seconds MAC Proj :0.006099095 seconds Nodal Proj :0.007302411 seconds Reactions :0.01210546 seconds Misc :0.001405805 seconds Base State :8.400002116e-08 seconds Time to advance time step: 0.033101522 Call to estdt for level 0 gives dt_lev = 1.738989551e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 31 gives dt =1e+20 dt_growth factor limits the new dt = 0.008243701216  Timestep 31 starts with TIME = 0.1267258932 DT = 0.008243701216 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.143997884e-29 MLMG: Initial residual (resid0) = 1.143997884e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.075244338e-39, 9.399006352e-11 MLMG: Timers: Solve = 0.004670943 Iter = 0.00446348 Bottom = 0.000112378 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.143997884e-29 MLMG: Initial residual (resid0) = 1.075244338e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000207113 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.744588982e-19 MLMG: Initial residual (resid0) = 4.744588982e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.409524954e-30, 1.772445408e-11 MLMG: Timers: Solve = 0.006328235 Iter = 0.00615142 Bottom = 0.000122719 Done calling nodal solver Timestep 31 ends with TIME = 0.1349695944 DT = 0.008243701216 Timing summary: Advection :0.005953315 seconds MAC Proj :0.005553851 seconds Nodal Proj :0.007069749 seconds Reactions :0.01193863 seconds Misc :0.001415259 seconds Base State :8.699998943e-08 seconds Time to advance time step: 0.032094012 Call to estdt for level 0 gives dt_lev = 1.656272178e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 32 gives dt =1e+20 dt_growth factor limits the new dt = 0.008655886277  Timestep 32 starts with TIME = 0.1349695944 DT = 0.008655886277 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.20132055e-29 MLMG: Initial residual (resid0) = 1.20132055e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.128845405e-39, 9.396704365e-11 MLMG: Timers: Solve = 0.004685057 Iter = 0.004479101 Bottom = 0.000111765 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.20132055e-29 MLMG: Initial residual (resid0) = 1.128845405e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.0002274 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.981818431e-19 MLMG: Initial residual (resid0) = 4.981818431e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.830051757e-30, 1.772455556e-11 MLMG: Timers: Solve = 0.006234561 Iter = 0.006060134 Bottom = 0.000121771 Done calling nodal solver Timestep 32 ends with TIME = 0.1436254807 DT = 0.008655886277 Timing summary: Advection :0.005954131 seconds MAC Proj :0.00557025 seconds Nodal Proj :0.007007011 seconds Reactions :0.012175963 seconds Misc :0.001378261 seconds Base State :8.699998943e-08 seconds Time to advance time step: 0.032241229 Call to estdt for level 0 gives dt_lev = 1.57745258e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 33 gives dt =1e+20 dt_growth factor limits the new dt = 0.00908868059  Timestep 33 starts with TIME = 0.1436254807 DT = 0.00908868059 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.261518372e-29 MLMG: Initial residual (resid0) = 1.261518372e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.185446653e-39, 9.396982869e-11 MLMG: Timers: Solve = 0.004668264 Iter = 0.00445981 Bottom = 0.00011232 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.261518372e-29 MLMG: Initial residual (resid0) = 1.185446653e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000206272 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.230909353e-19 MLMG: Initial residual (resid0) = 5.230909353e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.271571197e-30, 1.772458778e-11 MLMG: Timers: Solve = 0.006309697 Iter = 0.006135241 Bottom = 0.000125307 Done calling nodal solver Timestep 33 ends with TIME = 0.1527141613 DT = 0.00908868059 Timing summary: Advection :0.005953462 seconds MAC Proj :0.005607519 seconds Nodal Proj :0.007055451 seconds Reactions :0.011960327 seconds Misc :0.001349734 seconds Base State :8.100005289e-08 seconds Time to advance time step: 0.032081482 Call to estdt for level 0 gives dt_lev = 1.502382666e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 34 gives dt =1e+20 dt_growth factor limits the new dt = 0.00954311462  Timestep 34 starts with TIME = 0.1527141613 DT = 0.00954311462 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.324617027e-29 MLMG: Initial residual (resid0) = 1.324617027e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.244727183e-39, 9.396883457e-11 MLMG: Timers: Solve = 0.004721724 Iter = 0.004518353 Bottom = 0.000110707 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.324617027e-29 MLMG: Initial residual (resid0) = 1.244727183e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000206257 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.49245482e-19 MLMG: Initial residual (resid0) = 5.49245482e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.735142535e-30, 1.772457463e-11 MLMG: Timers: Solve = 0.006310529 Iter = 0.006132257 Bottom = 0.000131362 Done calling nodal solver Timestep 34 ends with TIME = 0.1622572759 DT = 0.00954311462 Timing summary: Advection :0.005999325 seconds MAC Proj :0.005610609 seconds Nodal Proj :0.007061838 seconds Reactions :0.012100898 seconds Misc :0.001403677 seconds Base State :8.600000001e-08 seconds Time to advance time step: 0.032328524 Call to estdt for level 0 gives dt_lev = 1.430870716e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 35 gives dt =1e+20 dt_growth factor limits the new dt = 0.01002027035  Timestep 35 starts with TIME = 0.1622572759 DT = 0.01002027035 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.390880152e-29 MLMG: Initial residual (resid0) = 1.390880152e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.307016301e-39, 9.397044739e-11 MLMG: Timers: Solve = 0.004844687 Iter = 0.00463552 Bottom = 0.000111796 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.390880152e-29 MLMG: Initial residual (resid0) = 1.307016301e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000208084 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.681793327e-19 MLMG: Initial residual (resid0) = 5.681793327e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.549561715e-29, 8.007263646e-11 MLMG: Timers: Solve = 0.007299027 Iter = 0.007120731 Bottom = 0.000134215 Done calling nodal solver Timestep 35 ends with TIME = 0.1722775463 DT = 0.01002027035 Timing summary: Advection :0.00613148 seconds MAC Proj :0.005711616 seconds Nodal Proj :0.008140074 seconds Reactions :0.012699563 seconds Misc :0.001394836 seconds Base State :5.200001851e-08 seconds Time to advance time step: 0.034257732 Call to estdt for level 0 gives dt_lev = 2.977709039e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 36 gives dt =1e+20 dt_growth factor limits the new dt = 0.01052128387  Timestep 36 starts with TIME = 0.1722775463 DT = 0.01052128387 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 4.305515288e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.232267053e-30, 5.184668742e-11 MLMG: Timers: Solve = 0.005228561 Iter = 0.00502125 Bottom = 0.000112519 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 2.232267053e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000217533 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.055431439e-19 MLMG: Initial residual (resid0) = 6.055431439e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.073306314e-29, 1.772468773e-11 MLMG: Timers: Solve = 0.006351191 Iter = 0.006174018 Bottom = 0.000123969 Done calling nodal solver Timestep 36 ends with TIME = 0.1827988301 DT = 0.01052128387 Timing summary: Advection :0.005791352 seconds MAC Proj :0.006158629 seconds Nodal Proj :0.007081987 seconds Reactions :0.012446656 seconds Misc :0.001418787 seconds Base State :8.500001059e-08 seconds Time to advance time step: 0.033068134 Call to estdt for level 0 gives dt_lev = 1.290240107e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 37 gives dt =1e+20 dt_growth factor limits the new dt = 0.01104734806  Timestep 37 starts with TIME = 0.1827988301 DT = 0.01104734806 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.531602761e-29 MLMG: Initial residual (resid0) = 1.531602761e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.182310547e-39, 7.719433372e-11 MLMG: Timers: Solve = 0.005045613 Iter = 0.004840306 Bottom = 0.0001228 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.531602761e-29 MLMG: Initial residual (resid0) = 1.182310547e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000206849 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.264177143e-19 MLMG: Initial residual (resid0) = 6.264177143e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.855293464e-29, 7.750887871e-11 MLMG: Timers: Solve = 0.006487821 Iter = 0.006310956 Bottom = 0.000141656 Done calling nodal solver Timestep 37 ends with TIME = 0.1938461782 DT = 0.01104734806 Timing summary: Advection :0.005907106 seconds MAC Proj :0.005960415 seconds Nodal Proj :0.007222113 seconds Reactions :0.012501445 seconds Misc :0.00140283 seconds Base State :9.00000714e-08 seconds Time to advance time step: 0.033154181 Call to estdt for level 0 gives dt_lev = 2.789553225e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 38 gives dt =1e+20 dt_growth factor limits the new dt = 0.01159971547  Timestep 38 starts with TIME = 0.1938461782 DT = 0.01159971547 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 4.746830605e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.490916131e-30, 5.247535331e-11 MLMG: Timers: Solve = 0.004758508 Iter = 0.004550192 Bottom = 0.000115349 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 2.490916131e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000219289 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.676113162e-19 MLMG: Initial residual (resid0) = 6.676113162e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.183310617e-29, 1.772454403e-11 MLMG: Timers: Solve = 0.006235025 Iter = 0.00605651 Bottom = 0.000121031 Done calling nodal solver Timestep 38 ends with TIME = 0.2054458937 DT = 0.01159971547 Timing summary: Advection :0.005656409 seconds MAC Proj :0.005636574 seconds Nodal Proj :0.007016174 seconds Reactions :0.013414543 seconds Misc :0.001399147 seconds Base State :8.400002116e-08 seconds Time to advance time step: 0.033283728 Call to estdt for level 0 gives dt_lev = 1.16844655e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 39 gives dt =1e+20 dt_growth factor limits the new dt = 0.01217970124  Timestep 39 starts with TIME = 0.2054458937 DT = 0.01217970124 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.536075919e-29 MLMG: Initial residual (resid0) = 1.536075919e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.17936782e-39, 7.677796427e-11 MLMG: Timers: Solve = 0.004998988 Iter = 0.004781163 Bottom = 0.000111129 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.536075919e-29 MLMG: Initial residual (resid0) = 1.17936782e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000208999 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.00991882e-19 MLMG: Initial residual (resid0) = 7.00991882e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.242484815e-29, 1.772466767e-11 MLMG: Timers: Solve = 0.006315448 Iter = 0.006133818 Bottom = 0.000134468 Done calling nodal solver Timestep 39 ends with TIME = 0.2176255949 DT = 0.01217970124 Timing summary: Advection :0.005902614 seconds MAC Proj :0.00596543 seconds Nodal Proj :0.007065858 seconds Reactions :0.012086213 seconds Misc :0.001411624 seconds Base State :8.900008197e-08 seconds Time to advance time step: 0.032590205 Call to estdt for level 0 gives dt_lev = 1.116518296e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 40 gives dt =1e+20 dt_growth factor limits the new dt = 0.0127886863  Timestep 40 starts with TIME = 0.2176255949 DT = 0.0127886863 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.750107688e-29 MLMG: Initial residual (resid0) = 1.750107688e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.667934734e-39, 9.530469151e-11 MLMG: Timers: Solve = 0.004739548 Iter = 0.004532864 Bottom = 0.000112532 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.750107688e-29 MLMG: Initial residual (resid0) = 1.667934734e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000206143 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.360414761e-19 MLMG: Initial residual (resid0) = 7.360414761e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.304605685e-29, 1.772462188e-11 MLMG: Timers: Solve = 0.006274157 Iter = 0.006072565 Bottom = 0.000134639 Done calling nodal solver Timestep 40 ends with TIME = 0.2304142812 DT = 0.0127886863 Timing summary: Advection :0.005909255 seconds MAC Proj :0.005619516 seconds Nodal Proj :0.007059243 seconds Reactions :0.012143094 seconds Misc :0.001375396 seconds Base State :7.899996035e-08 seconds Time to advance time step: 0.032263415 Call to estdt for level 0 gives dt_lev = 1.065046887e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 41 gives dt =1e+20 dt_growth factor limits the new dt = 0.01342812062  Timestep 41 starts with TIME = 0.2304142812 DT = 0.01342812062 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.863121796e-29 MLMG: Initial residual (resid0) = 1.863121796e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.751491358e-39, 9.400841973e-11 MLMG: Timers: Solve = 0.004825696 Iter = 0.004471908 Bottom = 0.000111996 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.863121796e-29 MLMG: Initial residual (resid0) = 1.751491358e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000208962 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.728435499e-19 MLMG: Initial residual (resid0) = 7.728435499e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.369865821e-29, 1.772500814e-11 MLMG: Timers: Solve = 0.006311737 Iter = 0.006102637 Bottom = 0.000122929 Done calling nodal solver Timestep 41 ends with TIME = 0.2438424018 DT = 0.01342812062 Timing summary: Advection :0.006323233 seconds MAC Proj :0.005777657 seconds Nodal Proj :0.007024209 seconds Reactions :0.012778069 seconds Misc :0.001394536 seconds Base State :5.300000794e-08 seconds Time to advance time step: 0.033462699 Call to estdt for level 0 gives dt_lev = 1.015209966e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 42 gives dt =1e+20 dt_growth factor limits the new dt = 0.01409952665  Timestep 42 starts with TIME = 0.2438424018 DT = 0.01409952665 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.957437553e-29 MLMG: Initial residual (resid0) = 1.957437553e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.839212642e-39, 9.396022058e-11 MLMG: Timers: Solve = 0.00468844 Iter = 0.004487424 Bottom = 0.000111223 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.957437553e-29 MLMG: Initial residual (resid0) = 1.839212642e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000240509 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.114857274e-19 MLMG: Initial residual (resid0) = 8.114857274e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.438294112e-29, 1.772420714e-11 MLMG: Timers: Solve = 0.006296021 Iter = 0.006118504 Bottom = 0.00012099 Done calling nodal solver Timestep 42 ends with TIME = 0.2579419285 DT = 0.01409952665 Timing summary: Advection :0.005898521 seconds MAC Proj :0.005621584 seconds Nodal Proj :0.007055177 seconds Reactions :0.012311258 seconds Misc :0.001391468 seconds Base State :8.299991805e-08 seconds Time to advance time step: 0.032443639 Call to estdt for level 0 gives dt_lev = 9.673808914e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 43 gives dt =1e+20 dt_growth factor limits the new dt = 0.01480450298  Timestep 43 starts with TIME = 0.2579419285 DT = 0.01480450298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.055305455e-29 MLMG: Initial residual (resid0) = 2.055305455e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.931045336e-39, 9.395417752e-11 MLMG: Timers: Solve = 0.004788619 Iter = 0.004531522 Bottom = 0.000114173 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.055305455e-29 MLMG: Initial residual (resid0) = 1.931045336e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000232184 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.520600138e-19 MLMG: Initial residual (resid0) = 8.520600138e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.510256484e-29, 1.772476657e-11 MLMG: Timers: Solve = 0.006229789 Iter = 0.006051242 Bottom = 0.000122216 Done calling nodal solver Timestep 43 ends with TIME = 0.2727464314 DT = 0.01480450298 Timing summary: Advection :0.006429603 seconds MAC Proj :0.005828591 seconds Nodal Proj :0.006997685 seconds Reactions :0.011956933 seconds Misc :0.001369069 seconds Base State :7.400001323e-08 seconds Time to advance time step: 0.032733624 Call to estdt for level 0 gives dt_lev = 9.21627116e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 44 gives dt =1e+20 dt_growth factor limits the new dt = 0.01554472813  Timestep 44 starts with TIME = 0.2727464314 DT = 0.01554472813 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.158165969e-29 MLMG: Initial residual (resid0) = 2.158165969e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.027690088e-39, 9.395431664e-11 MLMG: Timers: Solve = 0.005124623 Iter = 0.004711561 Bottom = 0.000112703 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.158165969e-29 MLMG: Initial residual (resid0) = 2.027690088e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000205887 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.946630145e-19 MLMG: Initial residual (resid0) = 8.946630145e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.585743309e-29, 1.772447595e-11 MLMG: Timers: Solve = 0.006357349 Iter = 0.006146472 Bottom = 0.000131591 Done calling nodal solver Timestep 44 ends with TIME = 0.2882911596 DT = 0.01554472813 Timing summary: Advection :0.005959228 seconds MAC Proj :0.006060797 seconds Nodal Proj :0.007123564 seconds Reactions :0.012146752 seconds Misc :0.00136932 seconds Base State :8.200004231e-08 seconds Time to advance time step: 0.032816412 Call to estdt for level 0 gives dt_lev = 8.779254781e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 45 gives dt =1e+20 dt_growth factor limits the new dt = 0.01632196453  Timestep 45 starts with TIME = 0.2882911596 DT = 0.01632196453 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.2662186e-29 MLMG: Initial residual (resid0) = 2.2662186e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.128830206e-39, 9.393754894e-11 MLMG: Timers: Solve = 0.004779207 Iter = 0.004563823 Bottom = 0.000112577 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.2662186e-29 MLMG: Initial residual (resid0) = 2.128830206e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000225406 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.053842861e-18 MLMG: Initial residual (resid0) = 1.053842861e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 6.68124357e-29, 6.339885971e-11 MLMG: Timers: Solve = 0.006247755 Iter = 0.006072571 Bottom = 0.000121543 Done calling nodal solver Timestep 45 ends with TIME = 0.3046131241 DT = 0.01632196453 Timing summary: Advection :0.006044702 seconds MAC Proj :0.005708323 seconds Nodal Proj :0.006978924 seconds Reactions :0.012081054 seconds Misc :0.001390732 seconds Base State :9.099994713e-08 seconds Time to advance time step: 0.032363627 Call to estdt for level 0 gives dt_lev = 2.027437947e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 46 gives dt =1e+20 dt_growth factor limits the new dt = 0.01713806276  Timestep 46 starts with TIME = 0.3046131241 DT = 0.01713806276 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 7.013230718e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.387375708e-30, 4.829978999e-11 MLMG: Timers: Solve = 0.004686082 Iter = 0.004475185 Bottom = 0.000109824 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 3.387375708e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000204904 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 9.863659735e-19 MLMG: Initial residual (resid0) = 9.863659735e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.748282166e-29, 1.772447766e-11 MLMG: Timers: Solve = 0.006308623 Iter = 0.006102988 Bottom = 0.000121112 Done calling nodal solver Timestep 46 ends with TIME = 0.3217511869 DT = 0.01713806276 Timing summary: Advection :0.00616461 seconds MAC Proj :0.005593298 seconds Nodal Proj :0.007090801 seconds Reactions :0.012630528 seconds Misc :0.001565139 seconds Base State :9.699999737e-08 seconds Time to advance time step: 0.033202922 Call to estdt for level 0 gives dt_lev = 7.924349732e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 47 gives dt =1e+20 dt_growth factor limits the new dt = 0.0179949659  Timestep 47 starts with TIME = 0.3217511869 DT = 0.0179949659 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.807872089e-29 MLMG: Initial residual (resid0) = 1.807872089e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.373027268e-39, 7.59471467e-11 MLMG: Timers: Solve = 0.005207639 Iter = 0.005000909 Bottom = 0.000111353 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.807872089e-29 MLMG: Initial residual (resid0) = 1.373027268e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000204325 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.035684272e-18 MLMG: Initial residual (resid0) = 1.035684272e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.835709756e-29, 1.772460783e-11 MLMG: Timers: Solve = 0.006391059 Iter = 0.006182168 Bottom = 0.000134389 Done calling nodal solver Timestep 47 ends with TIME = 0.3397461528 DT = 0.0179949659 Timing summary: Advection :0.005852869 seconds MAC Proj :0.006107259 seconds Nodal Proj :0.007157555 seconds Reactions :0.012065023 seconds Misc :0.00141082 seconds Base State :8.500001059e-08 seconds Time to advance time step: 0.032744544 Call to estdt for level 0 gives dt_lev = 7.566055076e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 48 gives dt =1e+20 dt_growth factor limits the new dt = 0.01889471419  Timestep 48 starts with TIME = 0.3397461528 DT = 0.01889471419 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.590316044e-29 MLMG: Initial residual (resid0) = 2.590316044e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.464404755e-39, 9.51391534e-11 MLMG: Timers: Solve = 0.004736558 Iter = 0.004529231 Bottom = 0.000112051 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.590316044e-29 MLMG: Initial residual (resid0) = 2.464404755e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000207979 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.087468486e-18 MLMG: Initial residual (resid0) = 1.087468486e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.927489948e-29, 1.772455913e-11 MLMG: Timers: Solve = 0.006328155 Iter = 0.00615189 Bottom = 0.000121789 Done calling nodal solver Timestep 48 ends with TIME = 0.358640867 DT = 0.01889471419 Timing summary: Advection :0.005991979 seconds MAC Proj :0.005674833 seconds Nodal Proj :0.007070163 seconds Reactions :0.012964705 seconds Misc :0.001356912 seconds Base State :6.700008726e-08 seconds Time to advance time step: 0.0332174 Call to estdt for level 0 gives dt_lev = 7.214097476e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 49 gives dt =1e+20 dt_growth factor limits the new dt = 0.0198394499  Timestep 49 starts with TIME = 0.358640867 DT = 0.0198394499 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.753899991e-29 MLMG: Initial residual (resid0) = 2.753899991e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.587581692e-39, 9.396062678e-11 MLMG: Timers: Solve = 0.004659077 Iter = 0.004453993 Bottom = 0.000110772 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.753899991e-29 MLMG: Initial residual (resid0) = 2.587570482e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000202702 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.086359695e-18 MLMG: Initial residual (resid0) = 1.086359695e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 4.01595875e-29, 3.696711842e-11 MLMG: Timers: Solve = 0.006276825 Iter = 0.006097665 Bottom = 0.000123377 Done calling nodal solver Timestep 49 ends with TIME = 0.3784803169 DT = 0.0198394499 Timing summary: Advection :0.005984362 seconds MAC Proj :0.005540037 seconds Nodal Proj :0.007034053 seconds Reactions :0.012574034 seconds Misc :0.001550774 seconds Base State :8.09999392e-08 seconds Time to advance time step: 0.032839581 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 50 gives dt =1e+20 dt_growth factor limits the new dt = 0.0208314224  Timestep 50 starts with TIME = 0.3784803169 DT = 0.0208314224 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 8.242756114e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.781214371e-30, 4.587318027e-11 MLMG: Timers: Solve = 0.00469136 Iter = 0.004476354 Bottom = 0.000116035 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 3.781214371e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000209377 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.198934006e-18 MLMG: Initial residual (resid0) = 1.198934006e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 2.125061471e-29, 1.772459085e-11 MLMG: Timers: Solve = 0.006283077 Iter = 0.006090079 Bottom = 0.000121925 Done calling nodal solver Timestep 50 ends with TIME = 0.3993117393 DT = 0.0208314224 Timing summary: Advection :0.005772178 seconds MAC Proj :0.005588615 seconds Nodal Proj :0.007037182 seconds Reactions :0.011852969 seconds Misc :0.00138905 seconds Base State :9.899997622e-08 seconds Time to advance time step: 0.031804452 Writing plotfile 50 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.016176219 Writing checkpoint 50 Writing checkpoint chk0000050 Total Time: 3.057858434 Unused ParmParse Variables: [TOP]::amr.check_file(nvals = 1) :: [test_stability_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] AMReX (25.11-20-ga7f0aed21606) finalized