Initializing AMReX (26.02-3-gfc7d9e75fc28)... MPI initialized with 16 MPI processes MPI initialized with thread support level 0 AMReX (26.02-3-gfc7d9e75fc28) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = 5peaks_const_grav.dat model file = 5peaks_const_grav.dat reading initial model 1000 points found in the initial model 10 variables found in the initial model WARNING: variable not found: gravity WARNING: variable not found: abar WARNING: variable not found: zbar WARNING: variable not found: gpot WARNING: variable not found: cno model file mapping, level: 0 dr of MAESTRO base state = 93750000.000000 dr of input file data = 10010010.010010 maximum radius (cell-centered) of input model = 10000000000.000000 WARNING: resolution of base state array is not an integer multiple of the initial model's resolution. make sure this is a desired property as this could lead to aliasing when performing the interpolation. modulus = 3659909.909910 setting r_cutoff to 105 radius at r_cutoff 9890625000 Maximum HSE Error = 0.054171 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile test_stability_pltInitData after InitData inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.015597402 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.000409765 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile test_stability_pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.013480685 Call to firstdt for level 0 gives dt_lev = 0.01907406555 Multiplying dt_lev by init_shrink; dt_lev = 0.001907406555 Minimum firstdt over all levels = 0.001907406555 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 4.945354899e-27 MLMG: Initial residual (resid0) = 4.945354899e-27 MLMG: Final Iter. 3 resid, resid/bnorm = 2.357566962e-30, 0.0004767235133 MLMG: Timers: Solve = 0.002736039 Iter = 0.002457799 Bottom = 5.6822e-05 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 1 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #2 Calling nodal solver MLMG: Initial rhs = 2.306075226e-30 MLMG: Initial residual (resid0) = 2.306075226e-30 MLMG: Final Iter. 5 resid, resid/bnorm = 1.933642558e-37, 8.384993415e-08 MLMG: Timers: Solve = 0.003923838 Iter = 0.003670142 Bottom = 7.198e-05 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 2 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #3 Calling nodal solver MLMG: Initial rhs = 9.742172194e-32 MLMG: Initial residual (resid0) = 9.742172194e-32 MLMG: Final Iter. 4 resid, resid/bnorm = 7.56277059e-41, 7.76292026e-10 MLMG: Timers: Solve = 0.003206299 Iter = 0.00291167 Bottom = 6.0403e-05 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 3 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Writing plotfile test_stability_pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.012152994 Doing initial pressure iteration #1  Timestep 0 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.893547601e-20 MLMG: Initial residual (resid0) = 4.893547601e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 4.517319639e-31, 9.231175431e-12 MLMG: Timers: Solve = 0.004541919 Iter = 0.00423607 Bottom = 0.000115653 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.893547507e-20 MLMG: Initial residual (resid0) = 2.477484298e-27 MLMG: Final Iter. 4 resid, resid/bnorm = 4.813594317e-30, 9.836615074e-11 MLMG: Timers: Solve = 0.001971437 Iter = 0.001742577 Bottom = 5.1686e-05 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.755411273e-17 MLMG: Initial residual (resid0) = 5.755411273e-17 MLMG: Final Iter. 9 resid, resid/bnorm = 1.020114247e-27, 1.772443703e-11 MLMG: Timers: Solve = 0.006341419 Iter = 0.006149409 Bottom = 0.000125608 Done calling nodal solver Timestep 0 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.005920126 seconds MAC Proj :0.00735747 seconds Nodal Proj :0.007160024 seconds Reactions :0.011737874 seconds Misc :0.001362691 seconds Base State :4.499997885e-08 seconds Time to advance time step: 0.036698807 Writing plotfile 0 after all initialization inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.012417137 Writing checkpoint 0 after all initialization Writing checkpoint chk0000000 Beginning main evolution  Timestep 1 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.257776132e-26 MLMG: Initial residual (resid0) = 1.257776132e-26 MLMG: Final Iter. 10 resid, resid/bnorm = 1.092354528e-37, 8.684808849e-12 MLMG: Timers: Solve = 0.004638969 Iter = 0.00438908 Bottom = 0.000116532 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.257776132e-26 MLMG: Initial residual (resid0) = 1.092354528e-37 MLMG: No iterations needed MLMG: Timers: Solve = 0.000220697 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.097790919e-19 MLMG: Initial residual (resid0) = 1.097790919e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.945791097e-30, 1.772460551e-11 MLMG: Timers: Solve = 0.006342485 Iter = 0.006149939 Bottom = 0.000138922 Done calling nodal solver Timestep 1 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.00594894 seconds MAC Proj :0.005625229 seconds Nodal Proj :0.007188526 seconds Reactions :0.011942813 seconds Misc :0.001426037 seconds Base State :5.000015335e-08 seconds Time to advance time step: 0.03707844 Call to estdt for level 0 gives dt_lev = 7.191087425e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 2 gives dt =1e+20 dt_growth factor limits the new dt = 0.002002776883  Timestep 2 starts with TIME = 0.001907406555 DT = 0.002002776883 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.08039884e-27 MLMG: Initial residual (resid0) = 8.08039884e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 1.160384542e-37, 1.436048597e-11 MLMG: Timers: Solve = 0.004289123 Iter = 0.004090451 Bottom = 0.000115519 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.498306041e-27 MLMG: Initial residual (resid0) = 2.601349809e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 8.687490856e-37, 9.146358118e-11 MLMG: Timers: Solve = 0.004249123 Iter = 0.004049938 Bottom = 0.000113196 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.096671578e-19 MLMG: Initial residual (resid0) = 1.096671578e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.008841827e-29, 9.199124398e-11 MLMG: Timers: Solve = 0.006298182 Iter = 0.006107976 Bottom = 0.000134711 Done calling nodal solver Timestep 2 ends with TIME = 0.003910183437 DT = 0.002002776883 Timing summary: Advection :0.00578848 seconds MAC Proj :0.009276622 seconds Nodal Proj :0.007131543 seconds Reactions :0.011975513 seconds Misc :0.001317855 seconds Base State :4.000003173e-08 seconds Time to advance time step: 0.035629326 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 3 gives dt =1e+20 dt_growth factor limits the new dt = 0.002102915727  Timestep 3 starts with TIME = 0.003910183437 DT = 0.002102915727 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 8.320997544e-21 MLMG: Final Iter. 10 resid, resid/bnorm = 7.677524121e-31, 9.226687161e-11 MLMG: Timers: Solve = 0.00428975 Iter = 0.004076347 Bottom = 0.000113071 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.320997544e-21 MLMG: Initial residual (resid0) = 7.677524121e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000204711 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.21031446e-19 MLMG: Initial residual (resid0) = 1.21031446e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.145245217e-30, 1.772469294e-11 MLMG: Timers: Solve = 0.006348019 Iter = 0.006150528 Bottom = 0.000125395 Done calling nodal solver Timestep 3 ends with TIME = 0.006013099164 DT = 0.002102915727 Timing summary: Advection :0.00555981 seconds MAC Proj :0.005256774 seconds Nodal Proj :0.00717782 seconds Reactions :0.012245332 seconds Misc :0.001288237 seconds Base State :6.100003702e-08 seconds Time to advance time step: 0.031653341 Call to estdt for level 0 gives dt_lev = 6.528670715e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 4 gives dt =1e+20 dt_growth factor limits the new dt = 0.002208061513  Timestep 4 starts with TIME = 0.006013099164 DT = 0.002208061513 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.3079729e-29 MLMG: Initial residual (resid0) = 1.3079729e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.129684783e-39, 8.63691276e-11 MLMG: Timers: Solve = 0.004268297 Iter = 0.004068835 Bottom = 0.000111522 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.3079729e-29 MLMG: Initial residual (resid0) = 1.129684783e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000201254 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.270830183e-19 MLMG: Initial residual (resid0) = 1.270830183e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.252519515e-30, 1.772478766e-11 MLMG: Timers: Solve = 0.006197295 Iter = 0.006002997 Bottom = 0.000124617 Done calling nodal solver Timestep 4 ends with TIME = 0.008221160677 DT = 0.002208061513 Timing summary: Advection :0.005715199 seconds MAC Proj :0.005218579 seconds Nodal Proj :0.007028803 seconds Reactions :0.011683063 seconds Misc :0.001292403 seconds Base State :3.799982551e-08 seconds Time to advance time step: 0.031087612 Call to estdt for level 0 gives dt_lev = 6.226377027e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 5 gives dt =1e+20 dt_growth factor limits the new dt = 0.002318464589  Timestep 5 starts with TIME = 0.008221160677 DT = 0.002318464589 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.295423824e-30 MLMG: Initial residual (resid0) = 3.295423824e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.024461011e-40, 9.177760352e-11 MLMG: Timers: Solve = 0.004250477 Iter = 0.004025454 Bottom = 0.00011298 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.295423824e-30 MLMG: Initial residual (resid0) = 3.024461011e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000201287 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.334371692e-19 MLMG: Initial residual (resid0) = 1.334371692e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.365126231e-30, 1.772464333e-11 MLMG: Timers: Solve = 0.006390018 Iter = 0.006195988 Bottom = 0.000127301 Done calling nodal solver Timestep 5 ends with TIME = 0.01053962527 DT = 0.002318464589 Timing summary: Advection :0.005772777 seconds MAC Proj :0.005219314 seconds Nodal Proj :0.007229623 seconds Reactions :0.012044735 seconds Misc :0.001299956 seconds Base State :6.00000476e-08 seconds Time to advance time step: 0.031697018 Call to estdt for level 0 gives dt_lev = 5.914991835e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 6 gives dt =1e+20 dt_growth factor limits the new dt = 0.002434387818  Timestep 6 starts with TIME = 0.01053962527 DT = 0.002434387818 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.377300377e-30 MLMG: Initial residual (resid0) = 3.377300377e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.175447418e-40, 9.402324529e-11 MLMG: Timers: Solve = 0.004224822 Iter = 0.0040094 Bottom = 0.000112165 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.377300377e-30 MLMG: Initial residual (resid0) = 3.175443914e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000209321 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.401090277e-19 MLMG: Initial residual (resid0) = 1.401090277e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.483390367e-30, 1.772469917e-11 MLMG: Timers: Solve = 0.006371229 Iter = 0.006172833 Bottom = 0.000125379 Done calling nodal solver Timestep 6 ends with TIME = 0.01297401308 DT = 0.002434387818 Timing summary: Advection :0.0059878 seconds MAC Proj :0.005227194 seconds Nodal Proj :0.007244376 seconds Reactions :0.011748638 seconds Misc :0.001272472 seconds Base State :4.100002116e-08 seconds Time to advance time step: 0.031620341 Call to estdt for level 0 gives dt_lev = 5.625582499e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 7 gives dt =1e+20 dt_growth factor limits the new dt = 0.002556107209  Timestep 7 starts with TIME = 0.01297401308 DT = 0.002556107209 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.542867857e-30 MLMG: Initial residual (resid0) = 3.542867857e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.33382217e-40, 9.409953474e-11 MLMG: Timers: Solve = 0.004245721 Iter = 0.004036099 Bottom = 0.000112661 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.542867857e-30 MLMG: Initial residual (resid0) = 3.33382217e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000202868 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.471144791e-19 MLMG: Initial residual (resid0) = 1.471144791e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.607576737e-30, 1.772481372e-11 MLMG: Timers: Solve = 0.006235252 Iter = 0.006046056 Bottom = 0.000140001 Done calling nodal solver Timestep 7 ends with TIME = 0.01553012029 DT = 0.002556107209 Timing summary: Advection :0.005737759 seconds MAC Proj :0.005175065 seconds Nodal Proj :0.007064998 seconds Reactions :0.011968719 seconds Misc :0.001296853 seconds Base State :3.700006346e-08 seconds Time to advance time step: 0.031384486 Call to estdt for level 0 gives dt_lev = 5.353302437e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 8 gives dt =1e+20 dt_growth factor limits the new dt = 0.002683912569  Timestep 8 starts with TIME = 0.01553012029 DT = 0.002683912569 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.719890133e-30 MLMG: Initial residual (resid0) = 3.719890133e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.500289421e-40, 9.409658071e-11 MLMG: Timers: Solve = 0.004263389 Iter = 0.004059381 Bottom = 0.000115126 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.719890133e-30 MLMG: Initial residual (resid0) = 3.500289421e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000200836 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.54470203e-19 MLMG: Initial residual (resid0) = 1.54470203e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.737926083e-30, 1.77246228e-11 MLMG: Timers: Solve = 0.006183369 Iter = 0.005977662 Bottom = 0.000123279 Done calling nodal solver Timestep 8 ends with TIME = 0.01821403286 DT = 0.002683912569 Timing summary: Advection :0.005982241 seconds MAC Proj :0.005201582 seconds Nodal Proj :0.007024496 seconds Reactions :0.011669933 seconds Misc :0.001263223 seconds Base State :3.700006346e-08 seconds Time to advance time step: 0.03127375 Call to estdt for level 0 gives dt_lev = 5.095587997e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 9 gives dt =1e+20 dt_growth factor limits the new dt = 0.002818108198  Timestep 9 starts with TIME = 0.01821403286 DT = 0.002818108198 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.905661102e-30 MLMG: Initial residual (resid0) = 3.905661102e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.676397606e-40, 9.412996953e-11 MLMG: Timers: Solve = 0.004222746 Iter = 0.004022814 Bottom = 0.000111923 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.905661102e-30 MLMG: Initial residual (resid0) = 3.676397606e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000205068 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.621937132e-19 MLMG: Initial residual (resid0) = 1.621937132e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.874823591e-30, 1.772463022e-11 MLMG: Timers: Solve = 0.006240001 Iter = 0.0060524 Bottom = 0.000126205 Done calling nodal solver Timestep 9 ends with TIME = 0.02103214106 DT = 0.002818108198 Timing summary: Advection :0.005831442 seconds MAC Proj :0.005152061 seconds Nodal Proj :0.007084367 seconds Reactions :0.011654723 seconds Misc :0.001311703 seconds Base State :3.900004231e-08 seconds Time to advance time step: 0.031185231 Call to estdt for level 0 gives dt_lev = 4.851262359e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 10 gives dt =1e+20 dt_growth factor limits the new dt = 0.002959013608  Timestep 10 starts with TIME = 0.02103214106 DT = 0.002959013608 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.100939546e-30 MLMG: Initial residual (resid0) = 4.100939546e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 3.860100828e-40, 9.412723071e-11 MLMG: Timers: Solve = 0.004274932 Iter = 0.004064171 Bottom = 0.000113762 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.100939546e-30 MLMG: Initial residual (resid0) = 3.860100828e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000233401 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.703033988e-19 MLMG: Initial residual (resid0) = 1.703033988e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.174813655e-29, 6.898357067e-11 MLMG: Timers: Solve = 0.006496617 Iter = 0.006303972 Bottom = 0.000130458 Done calling nodal solver Timestep 10 ends with TIME = 0.02399115467 DT = 0.002959013608 Timing summary: Advection :0.005712401 seconds MAC Proj :0.005234393 seconds Nodal Proj :0.007345748 seconds Reactions :0.011654937 seconds Misc :0.001275809 seconds Base State :3.900004231e-08 seconds Time to advance time step: 0.031363858 Call to estdt for level 0 gives dt_lev = 1.153494089e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 11 gives dt =1e+20 dt_growth factor limits the new dt = 0.003106964288  Timestep 11 starts with TIME = 0.02399115467 DT = 0.003106964288 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 1.271430598e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.310351499e-31, 4.963189897e-11 MLMG: Timers: Solve = 0.00425676 Iter = 0.004003588 Bottom = 0.000115335 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 6.310351499e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000197061 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.788185688e-19 MLMG: Initial residual (resid0) = 1.788185688e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.169478835e-30, 1.772455096e-11 MLMG: Timers: Solve = 0.006396299 Iter = 0.006208556 Bottom = 0.000142151 Done calling nodal solver Timestep 11 ends with TIME = 0.02709811896 DT = 0.003106964288 Timing summary: Advection :0.005529926 seconds MAC Proj :0.00519475 seconds Nodal Proj :0.007238343 seconds Reactions :0.012069291 seconds Misc :0.001273594 seconds Base State :4.100002116e-08 seconds Time to advance time step: 0.031508332 Call to estdt for level 0 gives dt_lev = 4.376646045e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 12 gives dt =1e+20 dt_growth factor limits the new dt = 0.003262312503  Timestep 12 starts with TIME = 0.02709811896 DT = 0.003262312503 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.931087603e-30 MLMG: Initial residual (resid0) = 2.931087603e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.211756947e-40, 7.545857536e-11 MLMG: Timers: Solve = 0.004224566 Iter = 0.004021288 Bottom = 0.000111869 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.931087603e-30 MLMG: Initial residual (resid0) = 2.211756947e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000201688 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.877594972e-19 MLMG: Initial residual (resid0) = 1.877594972e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.327886573e-30, 1.772419836e-11 MLMG: Timers: Solve = 0.006343354 Iter = 0.006113139 Bottom = 0.000125377 Done calling nodal solver Timestep 12 ends with TIME = 0.03036043146 DT = 0.003262312503 Timing summary: Advection :0.005755089999 seconds MAC Proj :0.005140819 seconds Nodal Proj :0.007153625 seconds Reactions :0.012076552 seconds Misc :0.001299678 seconds Base State :7.099993127e-08 seconds Time to advance time step: 0.031568593 Call to estdt for level 0 gives dt_lev = 4.177453783e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 13 gives dt =1e+20 dt_growth factor limits the new dt = 0.003425428128  Timestep 13 starts with TIME = 0.03036043146 DT = 0.003425428128 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.688248856e-30 MLMG: Initial residual (resid0) = 4.688248856e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.467598744e-40, 9.52935495e-11 MLMG: Timers: Solve = 0.004365636 Iter = 0.00414882 Bottom = 0.000126797 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.688248856e-30 MLMG: Initial residual (resid0) = 4.467598744e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000201545 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.971474721e-19 MLMG: Initial residual (resid0) = 1.971474721e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.494310995e-30, 1.7724351e-11 MLMG: Timers: Solve = 0.006205434 Iter = 0.006015859 Bottom = 0.000123686 Done calling nodal solver Timestep 13 ends with TIME = 0.03378585959 DT = 0.003425428128 Timing summary: Advection :0.005779958 seconds MAC Proj :0.005304219 seconds Nodal Proj :0.007037763 seconds Reactions :0.011775674 seconds Misc :0.001265635 seconds Base State :3.800005288e-08 seconds Time to advance time step: 0.031314849 Call to estdt for level 0 gives dt_lev = 3.982247017e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 14 gives dt =1e+20 dt_growth factor limits the new dt = 0.003596699534  Timestep 14 starts with TIME = 0.03378585959 DT = 0.003596699534 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.98227213e-30 MLMG: Initial residual (resid0) = 4.98227213e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 4.691855544e-40, 9.417100114e-11 MLMG: Timers: Solve = 0.004227163 Iter = 0.004017092 Bottom = 0.000113371 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.98227213e-30 MLMG: Initial residual (resid0) = 4.691855544e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022074 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.221658729e-19 MLMG: Initial residual (resid0) = 2.221658729e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.863225901e-30, 3.989463271e-11 MLMG: Timers: Solve = 0.006326107 Iter = 0.006098235 Bottom = 0.000130602 Done calling nodal solver Timestep 14 ends with TIME = 0.03738255912 DT = 0.003596699534 Timing summary: Advection :0.005738075 seconds MAC Proj :0.005174953 seconds Nodal Proj :0.007147271 seconds Reactions :0.012011156 seconds Misc :0.001317387 seconds Base State :6.599998414e-08 seconds Time to advance time step: 0.031520973 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 15 gives dt =1e+20 dt_growth factor limits the new dt = 0.003776534511  Timestep 15 starts with TIME = 0.03738255912 DT = 0.003776534511 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 1.44706648e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 8.546351457e-31, 5.905983986e-11 MLMG: Timers: Solve = 0.004288751 Iter = 0.004090752 Bottom = 0.000115348 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 8.546351457e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000201349 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.279163939e-19 MLMG: Initial residual (resid0) = 2.279163939e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.500913317e-29, 6.585367956e-11 MLMG: Timers: Solve = 0.006269412 Iter = 0.006032361 Bottom = 0.000125344 Done calling nodal solver Timestep 15 ends with TIME = 0.04115909363 DT = 0.003776534511 Timing summary: Advection :0.005639285 seconds MAC Proj :0.005214836 seconds Nodal Proj :0.00712382 seconds Reactions :0.011852556 seconds Misc :0.00135328 seconds Base State :4.100002116e-08 seconds Time to advance time step: 0.031334451 Call to estdt for level 0 gives dt_lev = 9.044183602e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 16 gives dt =1e+20 dt_growth factor limits the new dt = 0.003965361236  Timestep 16 starts with TIME = 0.04115909363 DT = 0.003965361236 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 1.62270343e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.18605137e-31, 3.812188509e-11 MLMG: Timers: Solve = 0.004281466 Iter = 0.004020575 Bottom = 0.000110564 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 6.18605137e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000214414 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.282228424e-19 MLMG: Initial residual (resid0) = 2.282228424e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.045223255e-30, 1.772488333e-11 MLMG: Timers: Solve = 0.006338566 Iter = 0.006139435 Bottom = 0.000140815 Done calling nodal solver Timestep 16 ends with TIME = 0.04512445487 DT = 0.003965361236 Timing summary: Advection :0.00548942 seconds MAC Proj :0.005251549 seconds Nodal Proj :0.007228206 seconds Reactions :0.011879783 seconds Misc :0.00128876 seconds Base State :6.00000476e-08 seconds Time to advance time step: 0.031290582 Call to estdt for level 0 gives dt_lev = 3.436635199e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 17 gives dt =1e+20 dt_growth factor limits the new dt = 0.004163629298  Timestep 17 starts with TIME = 0.04512445487 DT = 0.004163629298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.754712132e-30 MLMG: Initial residual (resid0) = 3.754712132e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 2.82584447e-40, 7.526128158e-11 MLMG: Timers: Solve = 0.004197214 Iter = 0.003997751 Bottom = 0.000111629 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.754712132e-30 MLMG: Initial residual (resid0) = 2.82584447e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000198137 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.396339845e-19 MLMG: Initial residual (resid0) = 2.396339845e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.247421825e-30, 1.772462213e-11 MLMG: Timers: Solve = 0.006317734 Iter = 0.006094715 Bottom = 0.000125542 Done calling nodal solver Timestep 17 ends with TIME = 0.04928808417 DT = 0.004163629298 Timing summary: Advection :0.005762652 seconds MAC Proj :0.005115875 seconds Nodal Proj :0.007182861 seconds Reactions :0.011794813 seconds Misc :0.001283126 seconds Base State :5.300012162e-08 seconds Time to advance time step: 0.03129232 Call to estdt for level 0 gives dt_lev = 3.276873657e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 18 gives dt =1e+20 dt_growth factor limits the new dt = 0.004371810763  Timestep 18 starts with TIME = 0.04928808417 DT = 0.004371810763 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.988437125e-30 MLMG: Initial residual (resid0) = 5.988437125e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.701673257e-40, 9.521137381e-11 MLMG: Timers: Solve = 0.004248516 Iter = 0.004048225 Bottom = 0.000111934 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.988437125e-30 MLMG: Initial residual (resid0) = 5.701673257e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000198956 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.516156837e-19 MLMG: Initial residual (resid0) = 2.516156837e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.459779676e-30, 1.772456951e-11 MLMG: Timers: Solve = 0.006281362 Iter = 0.006086791 Bottom = 0.000125467 Done calling nodal solver Timestep 18 ends with TIME = 0.05365989493 DT = 0.004371810763 Timing summary: Advection :0.005784332 seconds MAC Proj :0.005170368 seconds Nodal Proj :0.007093733 seconds Reactions :0.0120182 seconds Misc :0.001283024 seconds Base State :6.499999472e-08 seconds Time to advance time step: 0.031499339 Call to estdt for level 0 gives dt_lev = 3.122293372e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 19 gives dt =1e+20 dt_growth factor limits the new dt = 0.004590401301  Timestep 19 starts with TIME = 0.05365989493 DT = 0.004590401301 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.361637466e-30 MLMG: Initial residual (resid0) = 6.361637466e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.987748338e-40, 9.41227533e-11 MLMG: Timers: Solve = 0.004322871 Iter = 0.004115616 Bottom = 0.000113226 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.361637466e-30 MLMG: Initial residual (resid0) = 5.987748338e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000209259 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.641964679e-19 MLMG: Initial residual (resid0) = 2.641964679e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.68289866e-30, 1.772506157e-11 MLMG: Timers: Solve = 0.006238973 Iter = 0.006045461 Bottom = 0.000138945 Done calling nodal solver Timestep 19 ends with TIME = 0.05825029623 DT = 0.004590401301 Timing summary: Advection :0.005792831 seconds MAC Proj :0.005262258 seconds Nodal Proj :0.007039483 seconds Reactions :0.011874504 seconds Misc :0.001289159 seconds Base State :4.200001058e-08 seconds Time to advance time step: 0.031394812 Call to estdt for level 0 gives dt_lev = 2.974235616e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 20 gives dt =1e+20 dt_growth factor limits the new dt = 0.004819921366  Timestep 20 starts with TIME = 0.05825029623 DT = 0.004819921366 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.682786498e-30 MLMG: Initial residual (resid0) = 6.682786498e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.287114735e-40, 9.407923982e-11 MLMG: Timers: Solve = 0.004262029 Iter = 0.0040623 Bottom = 0.000113267 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.682786498e-30 MLMG: Initial residual (resid0) = 6.287114735e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000211736 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.774062913e-19 MLMG: Initial residual (resid0) = 2.774062913e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.916875074e-30, 1.772445409e-11 MLMG: Timers: Solve = 0.006504782 Iter = 0.006317011 Bottom = 0.000131916 Done calling nodal solver Timestep 20 ends with TIME = 0.0630702176 DT = 0.004819921366 Timing summary: Advection :0.005770508 seconds MAC Proj :0.005178944 seconds Nodal Proj :0.007299259 seconds Reactions :0.011636727 seconds Misc :0.001256841 seconds Base State :3.800005288e-08 seconds Time to advance time step: 0.031288865 Call to estdt for level 0 gives dt_lev = 2.832901245e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 21 gives dt =1e+20 dt_growth factor limits the new dt = 0.005060917435  Timestep 21 starts with TIME = 0.0630702176 DT = 0.005060917435 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.017767486e-30 MLMG: Initial residual (resid0) = 7.017767486e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 6.601040624e-40, 9.406183144e-11 MLMG: Timers: Solve = 0.004222443 Iter = 0.004021712 Bottom = 0.000111578 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.017767486e-30 MLMG: Initial residual (resid0) = 6.601040624e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000205162 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.869691725e-19 MLMG: Initial residual (resid0) = 2.869691725e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.297839054e-29, 8.007267937e-11 MLMG: Timers: Solve = 0.006372042 Iter = 0.006181292 Bottom = 0.000138871 Done calling nodal solver Timestep 21 ends with TIME = 0.06813113503 DT = 0.005060917435 Timing summary: Advection :0.005863275 seconds MAC Proj :0.005171237 seconds Nodal Proj :0.007205478 seconds Reactions :0.011657527 seconds Misc :0.001339913 seconds Base State :6.100003702e-08 seconds Time to advance time step: 0.031387302 Call to estdt for level 0 gives dt_lev = 5.895649157e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 22 gives dt =1e+20 dt_growth factor limits the new dt = 0.005313963306  Timestep 22 starts with TIME = 0.06813113503 DT = 0.005313963306 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 2.174577793e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 1.127453232e-30, 5.184699467e-11 MLMG: Timers: Solve = 0.004238597 Iter = 0.00402919 Bottom = 0.000114163 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 1.127453232e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000210863 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.058404362e-19 MLMG: Initial residual (resid0) = 3.058404362e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.420842792e-30, 1.772441493e-11 MLMG: Timers: Solve = 0.00636913 Iter = 0.006177066 Bottom = 0.000132418 Done calling nodal solver Timestep 22 ends with TIME = 0.07344509834 DT = 0.005313963306 Timing summary: Advection :0.005479555 seconds MAC Proj :0.005230886 seconds Nodal Proj :0.00723568 seconds Reactions :0.011928357 seconds Misc :0.001261202 seconds Base State :4.200001058e-08 seconds Time to advance time step: 0.031267233 Call to estdt for level 0 gives dt_lev = 2.554660013e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 23 gives dt =1e+20 dt_growth factor limits the new dt = 0.005579661472  Timestep 23 starts with TIME = 0.07344509834 DT = 0.005579661472 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.73348257e-30 MLMG: Initial residual (resid0) = 7.73348257e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 5.972845529e-40, 7.723358105e-11 MLMG: Timers: Solve = 0.004597824 Iter = 0.004332055 Bottom = 0.000113584 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.73348257e-30 MLMG: Initial residual (resid0) = 5.972845529e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000200564 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.21132458e-19 MLMG: Initial residual (resid0) = 3.21132458e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.691941506e-30, 1.77245911e-11 MLMG: Timers: Solve = 0.006346099 Iter = 0.006141323 Bottom = 0.000126608 Done calling nodal solver Timestep 23 ends with TIME = 0.07902475981 DT = 0.005579661472 Timing summary: Advection :0.005937822 seconds MAC Proj :0.005645381 seconds Nodal Proj :0.007168414 seconds Reactions :0.012046088 seconds Misc :0.001356955 seconds Base State :6.100003702e-08 seconds Time to advance time step: 0.032302351 Call to estdt for level 0 gives dt_lev = 2.439862005e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 24 gives dt =1e+20 dt_growth factor limits the new dt = 0.005858644545  Timestep 24 starts with TIME = 0.07902475981 DT = 0.005858644545 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.00564811e-30 MLMG: Initial residual (resid0) = 8.00564811e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 7.641742954e-40, 9.545439482e-11 MLMG: Timers: Solve = 0.004274377 Iter = 0.004048896 Bottom = 0.000112021 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.00564811e-30 MLMG: Initial residual (resid0) = 7.641742954e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000225071 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.371890809e-19 MLMG: Initial residual (resid0) = 3.371890809e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.976593952e-30, 1.772475531e-11 MLMG: Timers: Solve = 0.00636523 Iter = 0.006181317 Bottom = 0.000142321 Done calling nodal solver Timestep 24 ends with TIME = 0.08488340435 DT = 0.005858644545 Timing summary: Advection :0.005710577 seconds MAC Proj :0.005196041 seconds Nodal Proj :0.007183698 seconds Reactions :0.012502558 seconds Misc :0.00129332 seconds Base State :3.800005288e-08 seconds Time to advance time step: 0.032018937 Call to estdt for level 0 gives dt_lev = 2.326582163e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 25 gives dt =1e+20 dt_growth factor limits the new dt = 0.006151576773  Timestep 25 starts with TIME = 0.08488340435 DT = 0.006151576773 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.527771313e-30 MLMG: Initial residual (resid0) = 8.527771313e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.024857955e-40, 9.410264019e-11 MLMG: Timers: Solve = 0.004314346 Iter = 0.004102515 Bottom = 0.000115018 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.527771313e-30 MLMG: Initial residual (resid0) = 8.024857955e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000337606 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.540485349e-19 MLMG: Initial residual (resid0) = 3.540485349e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.275353834e-30, 1.772455812e-11 MLMG: Timers: Solve = 0.00648777 Iter = 0.00630923 Bottom = 0.000126272 Done calling nodal solver Timestep 25 ends with TIME = 0.09103498113 DT = 0.006151576773 Timing summary: Advection :0.005793636 seconds MAC Proj :0.005432961 seconds Nodal Proj :0.007297079 seconds Reactions :0.011793119 seconds Misc :0.001273421 seconds Base State :3.699983608e-08 seconds Time to advance time step: 0.031734347 Call to estdt for level 0 gives dt_lev = 2.21729507e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 26 gives dt =1e+20 dt_growth factor limits the new dt = 0.006459155611  Timestep 26 starts with TIME = 0.09103498113 DT = 0.006459155611 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.960012316e-30 MLMG: Initial residual (resid0) = 8.960012316e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.424844588e-40, 9.402715411e-11 MLMG: Timers: Solve = 0.004225872 Iter = 0.004016598 Bottom = 0.000114756 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.960012316e-30 MLMG: Initial residual (resid0) = 8.424844588e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000202161 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.717509617e-19 MLMG: Initial residual (resid0) = 3.717509617e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.58913597e-30, 1.772459698e-11 MLMG: Timers: Solve = 0.006330037 Iter = 0.006144543 Bottom = 0.000127409 Done calling nodal solver Timestep 26 ends with TIME = 0.09749413674 DT = 0.006459155611 Timing summary: Advection :0.005982743 seconds MAC Proj :0.005139886 seconds Nodal Proj :0.00715721 seconds Reactions :0.011739714 seconds Misc :0.001274731 seconds Base State :3.700006346e-08 seconds Time to advance time step: 0.03142844 Call to estdt for level 0 gives dt_lev = 2.112511375e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 27 gives dt =1e+20 dt_growth factor limits the new dt = 0.006782113392  Timestep 27 starts with TIME = 0.09749413674 DT = 0.006782113392 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.408830982e-30 MLMG: Initial residual (resid0) = 9.408830982e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 8.846691478e-40, 9.402540544e-11 MLMG: Timers: Solve = 0.004276386 Iter = 0.004075543 Bottom = 0.000115315 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.408830982e-30 MLMG: Initial residual (resid0) = 8.846691478e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000203719 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.903385097e-19 MLMG: Initial residual (resid0) = 3.903385097e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.918614436e-30, 1.772465248e-11 MLMG: Timers: Solve = 0.006310257 Iter = 0.006096223 Bottom = 0.000129201 Done calling nodal solver Timestep 27 ends with TIME = 0.1042762501 DT = 0.006782113392 Timing summary: Advection :0.00576258 seconds MAC Proj :0.005187523 seconds Nodal Proj :0.00713817 seconds Reactions :0.011882539 seconds Misc :0.001282179 seconds Base State :4.200001058e-08 seconds Time to advance time step: 0.031387696 Call to estdt for level 0 gives dt_lev = 2.0124204e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 28 gives dt =1e+20 dt_growth factor limits the new dt = 0.007121219061  Timestep 28 starts with TIME = 0.1042762501 DT = 0.007121219061 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.880130395e-30 MLMG: Initial residual (resid0) = 9.880130395e-30 MLMG: Final Iter. 10 resid, resid/bnorm = 9.288520884e-40, 9.40121285e-11 MLMG: Timers: Solve = 0.004255566 Iter = 0.00400011 Bottom = 0.000113158 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.880130395e-30 MLMG: Initial residual (resid0) = 9.288520884e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000198316 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.098554352e-19 MLMG: Initial residual (resid0) = 4.098554352e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.264511454e-30, 1.772457025e-11 MLMG: Timers: Solve = 0.00630131 Iter = 0.006102528 Bottom = 0.000135199 Done calling nodal solver Timestep 28 ends with TIME = 0.1113974692 DT = 0.007121219061 Timing summary: Advection :0.00588749 seconds MAC Proj :0.005154876 seconds Nodal Proj :0.007142049 seconds Reactions :0.012234747 seconds Misc :0.001286404 seconds Base State :4.200001058e-08 seconds Time to advance time step: 0.031847759 Call to estdt for level 0 gives dt_lev = 1.916904797e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 29 gives dt =1e+20 dt_growth factor limits the new dt = 0.007477280014  Timestep 29 starts with TIME = 0.1113974692 DT = 0.007477280014 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.037425901e-29 MLMG: Initial residual (resid0) = 1.037425901e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 9.752925208e-40, 9.401081271e-11 MLMG: Timers: Solve = 0.004248466 Iter = 0.004046322 Bottom = 0.000114257 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.037425901e-29 MLMG: Initial residual (resid0) = 9.752925208e-40 MLMG: No iterations needed MLMG: Timers: Solve = 0.000204779 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.30348207e-19 MLMG: Initial residual (resid0) = 4.30348207e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.627838138e-30, 1.77248052e-11 MLMG: Timers: Solve = 0.006250979 Iter = 0.00604421 Bottom = 0.000130847 Done calling nodal solver Timestep 29 ends with TIME = 0.1188747492 DT = 0.007477280014 Timing summary: Advection :0.00583821 seconds MAC Proj :0.005162596 seconds Nodal Proj :0.007074004 seconds Reactions :0.011719033 seconds Misc :0.001284615 seconds Base State :3.700006346e-08 seconds Time to advance time step: 0.031210157 Call to estdt for level 0 gives dt_lev = 1.825812456e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 30 gives dt =1e+20 dt_growth factor limits the new dt = 0.007851144015  Timestep 30 starts with TIME = 0.1188747492 DT = 0.007851144015 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.08944873e-29 MLMG: Initial residual (resid0) = 1.08944873e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.023977833e-39, 9.399045635e-11 MLMG: Timers: Solve = 0.004352236 Iter = 0.004088886 Bottom = 0.000114861 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.08944873e-29 MLMG: Initial residual (resid0) = 1.023977833e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000197801 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.518656173e-19 MLMG: Initial residual (resid0) = 4.518656173e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.00907597e-30, 1.772446423e-11 MLMG: Timers: Solve = 0.006381813 Iter = 0.006183037 Bottom = 0.00012668 Done calling nodal solver Timestep 30 ends with TIME = 0.1267258932 DT = 0.007851144015 Timing summary: Advection :0.005813603 seconds MAC Proj :0.005282014 seconds Nodal Proj :0.007225245 seconds Reactions :0.01178942 seconds Misc :0.001354072 seconds Base State :4.200001058e-08 seconds Time to advance time step: 0.031608106 Call to estdt for level 0 gives dt_lev = 1.738989551e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 31 gives dt =1e+20 dt_growth factor limits the new dt = 0.008243701216  Timestep 31 starts with TIME = 0.1267258932 DT = 0.008243701216 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.143997884e-29 MLMG: Initial residual (resid0) = 1.143997884e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.075244338e-39, 9.399006352e-11 MLMG: Timers: Solve = 0.004216884 Iter = 0.004017234 Bottom = 0.000116793 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.143997884e-29 MLMG: Initial residual (resid0) = 1.075244338e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000213501 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.744588982e-19 MLMG: Initial residual (resid0) = 4.744588982e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.409524954e-30, 1.772445408e-11 MLMG: Timers: Solve = 0.006498896 Iter = 0.0062639 Bottom = 0.000126195 Done calling nodal solver Timestep 31 ends with TIME = 0.1349695944 DT = 0.008243701216 Timing summary: Advection :0.006029312 seconds MAC Proj :0.005151892 seconds Nodal Proj :0.007331898 seconds Reactions :0.011864823 seconds Misc :0.001298419 seconds Base State :3.800005288e-08 seconds Time to advance time step: 0.031805888 Call to estdt for level 0 gives dt_lev = 1.656272178e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 32 gives dt =1e+20 dt_growth factor limits the new dt = 0.008655886277  Timestep 32 starts with TIME = 0.1349695944 DT = 0.008655886277 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.20132055e-29 MLMG: Initial residual (resid0) = 1.20132055e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.128845405e-39, 9.396704365e-11 MLMG: Timers: Solve = 0.004252058 Iter = 0.0040382 Bottom = 0.000111706 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.20132055e-29 MLMG: Initial residual (resid0) = 1.128845405e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000203686 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.981818431e-19 MLMG: Initial residual (resid0) = 4.981818431e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.830051757e-30, 1.772455556e-11 MLMG: Timers: Solve = 0.006363244 Iter = 0.00613636 Bottom = 0.000127139 Done calling nodal solver Timestep 32 ends with TIME = 0.1436254807 DT = 0.008655886277 Timing summary: Advection :0.005754963 seconds MAC Proj :0.005185388 seconds Nodal Proj :0.007211846 seconds Reactions :0.011850617 seconds Misc :0.001322718 seconds Base State :4.799994713e-08 seconds Time to advance time step: 0.031471534 Call to estdt for level 0 gives dt_lev = 1.57745258e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 33 gives dt =1e+20 dt_growth factor limits the new dt = 0.00908868059  Timestep 33 starts with TIME = 0.1436254807 DT = 0.00908868059 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.261518372e-29 MLMG: Initial residual (resid0) = 1.261518372e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.185446653e-39, 9.396982869e-11 MLMG: Timers: Solve = 0.004240794 Iter = 0.004042754 Bottom = 0.000113493 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.261518372e-29 MLMG: Initial residual (resid0) = 1.185446653e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000203671 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.230909353e-19 MLMG: Initial residual (resid0) = 5.230909353e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.271571197e-30, 1.772458778e-11 MLMG: Timers: Solve = 0.006240624 Iter = 0.006043818 Bottom = 0.000124815 Done calling nodal solver Timestep 33 ends with TIME = 0.1527141613 DT = 0.00908868059 Timing summary: Advection :0.005822321 seconds MAC Proj :0.005152462 seconds Nodal Proj :0.007083912 seconds Reactions :0.011828533 seconds Misc :0.001464695 seconds Base State :3.699983608e-08 seconds Time to advance time step: 0.031494625 Call to estdt for level 0 gives dt_lev = 1.502382666e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 34 gives dt =1e+20 dt_growth factor limits the new dt = 0.00954311462  Timestep 34 starts with TIME = 0.1527141613 DT = 0.00954311462 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.324617027e-29 MLMG: Initial residual (resid0) = 1.324617027e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.244727183e-39, 9.396883457e-11 MLMG: Timers: Solve = 0.004270692 Iter = 0.00407185 Bottom = 0.000114486 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.324617027e-29 MLMG: Initial residual (resid0) = 1.244727183e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000202698 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.49245482e-19 MLMG: Initial residual (resid0) = 5.49245482e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.735142535e-30, 1.772457463e-11 MLMG: Timers: Solve = 0.006318836 Iter = 0.00613231 Bottom = 0.000124591 Done calling nodal solver Timestep 34 ends with TIME = 0.1622572759 DT = 0.00954311462 Timing summary: Advection :0.005890325 seconds MAC Proj :0.005185627 seconds Nodal Proj :0.007154102 seconds Reactions :0.011984998 seconds Misc :0.001275438 seconds Base State :4.200001058e-08 seconds Time to advance time step: 0.031647732 Call to estdt for level 0 gives dt_lev = 1.430870716e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 35 gives dt =1e+20 dt_growth factor limits the new dt = 0.01002027035  Timestep 35 starts with TIME = 0.1622572759 DT = 0.01002027035 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.390880152e-29 MLMG: Initial residual (resid0) = 1.390880152e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.307016301e-39, 9.397044739e-11 MLMG: Timers: Solve = 0.004273767 Iter = 0.00407241 Bottom = 0.000114097 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.390880152e-29 MLMG: Initial residual (resid0) = 1.307016301e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000201467 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.681793327e-19 MLMG: Initial residual (resid0) = 5.681793327e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.549561715e-29, 8.007263646e-11 MLMG: Timers: Solve = 0.006287796 Iter = 0.006058309 Bottom = 0.000124125 Done calling nodal solver Timestep 35 ends with TIME = 0.1722775463 DT = 0.01002027035 Timing summary: Advection :0.005759789 seconds MAC Proj :0.005223634 seconds Nodal Proj :0.007133543 seconds Reactions :0.011864631 seconds Misc :0.001285188 seconds Base State :6.00000476e-08 seconds Time to advance time step: 0.031428647 Call to estdt for level 0 gives dt_lev = 2.977709039e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 36 gives dt =1e+20 dt_growth factor limits the new dt = 0.01052128387  Timestep 36 starts with TIME = 0.1722775463 DT = 0.01052128387 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 4.305515288e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.232267053e-30, 5.184668742e-11 MLMG: Timers: Solve = 0.004462365 Iter = 0.004261679 Bottom = 0.000111211 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 2.232267053e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000217036 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.055431439e-19 MLMG: Initial residual (resid0) = 6.055431439e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.073306314e-29, 1.772468773e-11 MLMG: Timers: Solve = 0.006320753 Iter = 0.006126942 Bottom = 0.000137578 Done calling nodal solver Timestep 36 ends with TIME = 0.1827988301 DT = 0.01052128387 Timing summary: Advection :0.005561093 seconds MAC Proj :0.005439378 seconds Nodal Proj :0.007194983 seconds Reactions :0.011918312 seconds Misc :0.001308768999 seconds Base State :6.100003702e-08 seconds Time to advance time step: 0.031557921 Call to estdt for level 0 gives dt_lev = 1.290240107e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 37 gives dt =1e+20 dt_growth factor limits the new dt = 0.01104734806  Timestep 37 starts with TIME = 0.1827988301 DT = 0.01104734806 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.531602761e-29 MLMG: Initial residual (resid0) = 1.531602761e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.182310547e-39, 7.719433372e-11 MLMG: Timers: Solve = 0.004340709 Iter = 0.004131646 Bottom = 0.000114332 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.531602761e-29 MLMG: Initial residual (resid0) = 1.182310547e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00020037 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.264177143e-19 MLMG: Initial residual (resid0) = 6.264177143e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.855293464e-29, 7.750887871e-11 MLMG: Timers: Solve = 0.006402821 Iter = 0.006177539 Bottom = 0.000139655 Done calling nodal solver Timestep 37 ends with TIME = 0.1938461782 DT = 0.01104734806 Timing summary: Advection :0.005747346 seconds MAC Proj :0.005261956 seconds Nodal Proj :0.007263899 seconds Reactions :0.011728449 seconds Misc :0.00131372 seconds Base State :4.999992598e-08 seconds Time to advance time step: 0.031453433 Call to estdt for level 0 gives dt_lev = 2.789553225e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 38 gives dt =1e+20 dt_growth factor limits the new dt = 0.01159971547  Timestep 38 starts with TIME = 0.1938461782 DT = 0.01159971547 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 4.746830605e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.490916131e-30, 5.247535331e-11 MLMG: Timers: Solve = 0.004401999 Iter = 0.004076589 Bottom = 0.000114965 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 2.490916131e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000211963 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.676113162e-19 MLMG: Initial residual (resid0) = 6.676113162e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.183310617e-29, 1.772454403e-11 MLMG: Timers: Solve = 0.00628472 Iter = 0.006069443 Bottom = 0.000137363 Done calling nodal solver Timestep 38 ends with TIME = 0.2054458937 DT = 0.01159971547 Timing summary: Advection :0.005526223 seconds MAC Proj :0.005372417 seconds Nodal Proj :0.007123111 seconds Reactions :0.011777106 seconds Misc :0.001259823 seconds Base State :4.300000001e-08 seconds Time to advance time step: 0.031192753 Call to estdt for level 0 gives dt_lev = 1.16844655e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 39 gives dt =1e+20 dt_growth factor limits the new dt = 0.01217970124  Timestep 39 starts with TIME = 0.2054458937 DT = 0.01217970124 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.536075919e-29 MLMG: Initial residual (resid0) = 1.536075919e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.17936782e-39, 7.677796427e-11 MLMG: Timers: Solve = 0.004345338 Iter = 0.004143976 Bottom = 0.000112109 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.536075919e-29 MLMG: Initial residual (resid0) = 1.17936782e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000257334 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.00991882e-19 MLMG: Initial residual (resid0) = 7.00991882e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.242484815e-29, 1.772466767e-11 MLMG: Timers: Solve = 0.006310832 Iter = 0.006119159 Bottom = 0.000124793 Done calling nodal solver Timestep 39 ends with TIME = 0.2176255949 DT = 0.01217970124 Timing summary: Advection :0.00577021 seconds MAC Proj :0.005354735 seconds Nodal Proj :0.007178896 seconds Reactions :0.012022318 seconds Misc :0.001276971 seconds Base State :4.499997885e-08 seconds Time to advance time step: 0.031750629 Call to estdt for level 0 gives dt_lev = 1.116518296e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 40 gives dt =1e+20 dt_growth factor limits the new dt = 0.0127886863  Timestep 40 starts with TIME = 0.2176255949 DT = 0.0127886863 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.750107688e-29 MLMG: Initial residual (resid0) = 1.750107688e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.667934734e-39, 9.530469151e-11 MLMG: Timers: Solve = 0.004304983 Iter = 0.004107314 Bottom = 0.000114617 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.750107688e-29 MLMG: Initial residual (resid0) = 1.667934734e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000199291 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.360414761e-19 MLMG: Initial residual (resid0) = 7.360414761e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.304605685e-29, 1.772462188e-11 MLMG: Timers: Solve = 0.006273644 Iter = 0.006081168 Bottom = 0.000132248 Done calling nodal solver Timestep 40 ends with TIME = 0.2304142812 DT = 0.0127886863 Timing summary: Advection :0.005844265999 seconds MAC Proj :0.005218423 seconds Nodal Proj :0.007096312 seconds Reactions :0.011796411 seconds Misc :0.00127837 seconds Base State :4.000003173e-08 seconds Time to advance time step: 0.031385853 Call to estdt for level 0 gives dt_lev = 1.065046887e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 41 gives dt =1e+20 dt_growth factor limits the new dt = 0.01342812062  Timestep 41 starts with TIME = 0.2304142812 DT = 0.01342812062 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.863121796e-29 MLMG: Initial residual (resid0) = 1.863121796e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.751491358e-39, 9.400841973e-11 MLMG: Timers: Solve = 0.00427504 Iter = 0.004071748 Bottom = 0.000115331 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.863121796e-29 MLMG: Initial residual (resid0) = 1.751491358e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000200487 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.728435499e-19 MLMG: Initial residual (resid0) = 7.728435499e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.369865821e-29, 1.772500814e-11 MLMG: Timers: Solve = 0.006386984 Iter = 0.006157862 Bottom = 0.000130711 Done calling nodal solver Timestep 41 ends with TIME = 0.2438424018 DT = 0.01342812062 Timing summary: Advection :0.005907337 seconds MAC Proj :0.005213181 seconds Nodal Proj :0.007202223 seconds Reactions :0.01181011 seconds Misc :0.001275545 seconds Base State :7.499988897e-08 seconds Time to advance time step: 0.031548698 Call to estdt for level 0 gives dt_lev = 1.015209966e+34 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 42 gives dt =1e+20 dt_growth factor limits the new dt = 0.01409952665  Timestep 42 starts with TIME = 0.2438424018 DT = 0.01409952665 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.957437553e-29 MLMG: Initial residual (resid0) = 1.957437553e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.839212642e-39, 9.396022058e-11 MLMG: Timers: Solve = 0.004199048 Iter = 0.004000938 Bottom = 0.000113339 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.957437553e-29 MLMG: Initial residual (resid0) = 1.839212642e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000201588 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.114857274e-19 MLMG: Initial residual (resid0) = 8.114857274e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.438294112e-29, 1.772420714e-11 MLMG: Timers: Solve = 0.006254396 Iter = 0.006066114 Bottom = 0.000129279 Done calling nodal solver Timestep 42 ends with TIME = 0.2579419285 DT = 0.01409952665 Timing summary: Advection :0.005904479 seconds MAC Proj :0.005106418 seconds Nodal Proj :0.007079462 seconds Reactions :0.011703654 seconds Misc :0.001276663 seconds Base State :4.200001058e-08 seconds Time to advance time step: 0.031200432 Call to estdt for level 0 gives dt_lev = 9.673808914e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 43 gives dt =1e+20 dt_growth factor limits the new dt = 0.01480450298  Timestep 43 starts with TIME = 0.2579419285 DT = 0.01480450298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.055305455e-29 MLMG: Initial residual (resid0) = 2.055305455e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.931045336e-39, 9.395417752e-11 MLMG: Timers: Solve = 0.004294598 Iter = 0.004056014 Bottom = 0.000122043 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.055305455e-29 MLMG: Initial residual (resid0) = 1.931045336e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00020279 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.520600138e-19 MLMG: Initial residual (resid0) = 8.520600138e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.510256484e-29, 1.772476657e-11 MLMG: Timers: Solve = 0.006253128 Iter = 0.006040531 Bottom = 0.000125373 Done calling nodal solver Timestep 43 ends with TIME = 0.2727464314 DT = 0.01480450298 Timing summary: Advection :0.005803444 seconds MAC Proj :0.005221798 seconds Nodal Proj :0.007059555 seconds Reactions :0.011765078 seconds Misc :0.001297096 seconds Base State :3.800005288e-08 seconds Time to advance time step: 0.031276884 Call to estdt for level 0 gives dt_lev = 9.21627116e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 44 gives dt =1e+20 dt_growth factor limits the new dt = 0.01554472813  Timestep 44 starts with TIME = 0.2727464314 DT = 0.01554472813 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.158165969e-29 MLMG: Initial residual (resid0) = 2.158165969e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.027690088e-39, 9.395431664e-11 MLMG: Timers: Solve = 0.004200647 Iter = 0.003997006 Bottom = 0.000119877 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.158165969e-29 MLMG: Initial residual (resid0) = 2.027690088e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000200588 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.946630145e-19 MLMG: Initial residual (resid0) = 8.946630145e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.585743309e-29, 1.772447595e-11 MLMG: Timers: Solve = 0.006250491 Iter = 0.006058488 Bottom = 0.000125695 Done calling nodal solver Timestep 44 ends with TIME = 0.2882911596 DT = 0.01554472813 Timing summary: Advection :0.00579844 seconds MAC Proj :0.005108872 seconds Nodal Proj :0.007067323 seconds Reactions :0.011716989 seconds Misc :0.001307344 seconds Base State :3.800005288e-08 seconds Time to advance time step: 0.031150575 Call to estdt for level 0 gives dt_lev = 8.779254781e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 45 gives dt =1e+20 dt_growth factor limits the new dt = 0.01632196453  Timestep 45 starts with TIME = 0.2882911596 DT = 0.01632196453 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.2662186e-29 MLMG: Initial residual (resid0) = 2.2662186e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.128830206e-39, 9.393754894e-11 MLMG: Timers: Solve = 0.004196454 Iter = 0.003995451 Bottom = 0.000118438 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.2662186e-29 MLMG: Initial residual (resid0) = 2.128830206e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000204322 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.053842861e-18 MLMG: Initial residual (resid0) = 1.053842861e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 6.68124357e-29, 6.339885971e-11 MLMG: Timers: Solve = 0.006304691 Iter = 0.00611285 Bottom = 0.000142725 Done calling nodal solver Timestep 45 ends with TIME = 0.3046131241 DT = 0.01632196453 Timing summary: Advection :0.005917658 seconds MAC Proj :0.005122517 seconds Nodal Proj :0.007155902 seconds Reactions :0.012110124 seconds Misc :0.001277234 seconds Base State :3.700006346e-08 seconds Time to advance time step: 0.031709371 Call to estdt for level 0 gives dt_lev = 2.027437947e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 46 gives dt =1e+20 dt_growth factor limits the new dt = 0.01713806276  Timestep 46 starts with TIME = 0.3046131241 DT = 0.01713806276 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 7.013230718e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.387375708e-30, 4.829978999e-11 MLMG: Timers: Solve = 0.004213717 Iter = 0.004005953 Bottom = 0.000115462 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 3.387375708e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000213883 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 9.863659735e-19 MLMG: Initial residual (resid0) = 9.863659735e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.748282166e-29, 1.772447766e-11 MLMG: Timers: Solve = 0.006164941 Iter = 0.005979404 Bottom = 0.000124987 Done calling nodal solver Timestep 46 ends with TIME = 0.3217511869 DT = 0.01713806276 Timing summary: Advection :0.00553941 seconds MAC Proj :0.005168127 seconds Nodal Proj :0.00698391 seconds Reactions :0.01170839 seconds Misc :0.001332623 seconds Base State :4.099979378e-08 seconds Time to advance time step: 0.030865614 Call to estdt for level 0 gives dt_lev = 7.924349732e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 47 gives dt =1e+20 dt_growth factor limits the new dt = 0.0179949659  Timestep 47 starts with TIME = 0.3217511869 DT = 0.0179949659 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.807872089e-29 MLMG: Initial residual (resid0) = 1.807872089e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 1.373027268e-39, 7.59471467e-11 MLMG: Timers: Solve = 0.006353355 Iter = 0.006108321 Bottom = 0.000113638 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.807872089e-29 MLMG: Initial residual (resid0) = 1.373027268e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000199756 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.035684272e-18 MLMG: Initial residual (resid0) = 1.035684272e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.835709756e-29, 1.772460783e-11 MLMG: Timers: Solve = 0.007314518 Iter = 0.00714072 Bottom = 0.000127431 Done calling nodal solver Timestep 47 ends with TIME = 0.3397461528 DT = 0.0179949659 Timing summary: Advection :0.006331743 seconds MAC Proj :0.007372201 seconds Nodal Proj :0.008213872 seconds Reactions :0.012713396 seconds Misc :0.001308314 seconds Base State :6.40000053e-08 seconds Time to advance time step: 0.036124352 Call to estdt for level 0 gives dt_lev = 7.566055076e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 48 gives dt =1e+20 dt_growth factor limits the new dt = 0.01889471419  Timestep 48 starts with TIME = 0.3397461528 DT = 0.01889471419 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.590316044e-29 MLMG: Initial residual (resid0) = 2.590316044e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.464404755e-39, 9.51391534e-11 MLMG: Timers: Solve = 0.004280625 Iter = 0.004073174 Bottom = 0.000112856 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.590316044e-29 MLMG: Initial residual (resid0) = 2.464404755e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00021984 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.087468486e-18 MLMG: Initial residual (resid0) = 1.087468486e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.927489948e-29, 1.772455913e-11 MLMG: Timers: Solve = 0.007330722 Iter = 0.007137127 Bottom = 0.000128036 Done calling nodal solver Timestep 48 ends with TIME = 0.358640867 DT = 0.01889471419 Timing summary: Advection :0.008162018 seconds MAC Proj :0.005232683 seconds Nodal Proj :0.008254297 seconds Reactions :0.013820106 seconds Misc :0.001610301 seconds Base State :4.200001058e-08 seconds Time to advance time step: 0.037278281 Call to estdt for level 0 gives dt_lev = 7.214097476e+33 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 49 gives dt =1e+20 dt_growth factor limits the new dt = 0.0198394499  Timestep 49 starts with TIME = 0.358640867 DT = 0.0198394499 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.753899991e-29 MLMG: Initial residual (resid0) = 2.753899991e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.587581692e-39, 9.396062678e-11 MLMG: Timers: Solve = 0.004299485 Iter = 0.004090442 Bottom = 0.000131225 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.753899991e-29 MLMG: Initial residual (resid0) = 2.587570482e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000200662 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.086359695e-18 MLMG: Initial residual (resid0) = 1.086359695e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 4.01595875e-29, 3.696711842e-11 MLMG: Timers: Solve = 0.006354276 Iter = 0.006168536 Bottom = 0.000125167 Done calling nodal solver Timestep 49 ends with TIME = 0.3784803169 DT = 0.0198394499 Timing summary: Advection :0.006006828 seconds MAC Proj :0.005234123 seconds Nodal Proj :0.007196496 seconds Reactions :0.012727234 seconds Misc :0.00155664 seconds Base State :3.800005288e-08 seconds Time to advance time step: 0.032886291 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 50 gives dt =1e+20 dt_growth factor limits the new dt = 0.0208314224  Timestep 50 starts with TIME = 0.3784803169 DT = 0.0208314224 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 8.242756114e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.781214371e-30, 4.587318027e-11 MLMG: Timers: Solve = 0.004360636 Iter = 0.004099499 Bottom = 0.000114848 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 3.781214371e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000202016 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.198934006e-18 MLMG: Initial residual (resid0) = 1.198934006e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 2.125061471e-29, 1.772459085e-11 MLMG: Timers: Solve = 0.006369838 Iter = 0.006143923 Bottom = 0.000130451 Done calling nodal solver Timestep 50 ends with TIME = 0.3993117393 DT = 0.0208314224 Timing summary: Advection :0.005884789 seconds MAC Proj :0.005322289 seconds Nodal Proj :0.007199955 seconds Reactions :0.012703497 seconds Misc :0.001307069 seconds Base State :3.899981493e-08 seconds Time to advance time step: 0.032571897 Writing plotfile 50 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.023771611 Writing checkpoint 50 Writing checkpoint chk0000050 Total Time: 3.663071344 Unused ParmParse Variables: [TOP]::amr.check_file(nvals = 1) :: [test_stability_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] AMReX (26.02-3-gfc7d9e75fc28) finalized