Initializing CUDA... CUDA initialized with 1 GPU AMReX (19.11-273-g35857d1b94d4) initialized Calling Setup() Calling ReadParameters() WARNING: burning_cutoff_density not supplied in the inputs file WARNING: setting burning_cutoff_density = base_cutoff_density reading extern runtime parameters ... ERROR: problem in the namelist Calling VariableSetup() Calling set_method_params() Calling BCSetup() Calling init_base_state_geometry() Calling Init() Calling InitData() ------------------------------------------------------------------------------ cutoff densities: low density cutoff (for mapping the model) = 0.1000000000E-09 buoyancy cutoff density (for zeroing rho - rho_0, centrifugal term) = 0.5000000000E-09 anelastic cutoff = 0.1000000000E-09 ------------------------------------------------------------------------------ Maximum HSE Error = 4.5474735088667091E-013 (after putting initial model into base state arrays, and for density < base_cutoff_density) ------------------------------------------------------------------------------ Writing plotfile RT_pltInitData after InitData Time to write plotfile: 0.112588857 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.003619862 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile RT_pltafter_InitProj after InitProj Time to write plotfile: 0.096323369 Call to firstdt for level 0 gives dt_lev = 0.000608983586 Multiplying dt_lev by init_shrink; dt_lev = 6.08983586e-05 Minimum firstdt over all levels = 6.08983586e-05 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.003355291 Iter = 0 Bottom = 0 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.08660444773 Minimum estdt over all levels = 0.08660444773 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.08660444773 Multiplying dt by init_shrink; dt = 0.008660444773 Ignoring this new dt since it's larger than the previous dt = 6.08983586e-05 Writing plotfile RT_pltafter_DivuIter after final DivuIter Time to write plotfile: 0.102355027 Doing initial pressure iteration #1 Timestep 0 starts with TIME = 0 DT = 6.08983586e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 0.002421164472 MLMG: Initial residual (resid0) = 0.002421164472 MLMG: Final Iter. 9 resid, resid/bnorm = 1.751907791e-13, 7.235806619e-11 MLMG: Timers: Solve = 0.082527181 Iter = 0.077768124 Bottom = 0.018073373 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 0.002421205691 MLMG: Initial residual (resid0) = 2.151449932e-06 MLMG: Final Iter. 7 resid, resid/bnorm = 9.927909287e-14, 4.100398955e-11 MLMG: Timers: Solve = 0.067291448 Iter = 0.063202907 Bottom = 0.013118127 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 58.12657035 MLMG: Initial residual (resid0) = 58.12657035 MLMG: Final Iter. 9 resid, resid/bnorm = 5.444000806e-11, 9.365769859e-13 MLMG: Timers: Solve = 0.084158388 Iter = 0.081952468 Bottom = 0.016906145 Done calling nodal solver Timestep 0 ends with TIME = 6.08983586e-05 DT = 6.08983586e-05 Timing summary: Advection :0.312544018 seconds MAC Proj :0.179495843 seconds Nodal Proj :0.098575976 seconds Reactions :0.01687293 seconds Misc :0.008683012 seconds Base State :0.002539829 seconds Time to advance time step: 0.616281393 Writing plotfile 0 after all initialization Time to write plotfile: 0.081307036 Calling Evolve() Timestep 1 starts with TIME = 0 DT = 6.08983586e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.394238647e-05 MLMG: Initial residual (resid0) = 2.394238647e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 3.184793474e-16, 1.330190488e-11 MLMG: Timers: Solve = 0.079777708 Iter = 0.077373334 Bottom = 0.018550327 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.394218844e-05 MLMG: Initial residual (resid0) = 1.928421101e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 6.036534882e-16, 2.521296204e-11 MLMG: Timers: Solve = 0.078201653 Iter = 0.075881652 Bottom = 0.016066057 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003539812449 MLMG: Initial residual (resid0) = 0.003539812449 MLMG: Final Iter. 9 resid, resid/bnorm = 3.304214541e-15, 9.334433923e-13 MLMG: Timers: Solve = 0.083501789 Iter = 0.081394719 Bottom = 0.016824309 Done calling nodal solver Timestep 1 ends with TIME = 6.08983586e-05 DT = 6.08983586e-05 Timing summary: Advection :0.25395781 seconds MAC Proj :0.183357976 seconds Nodal Proj :0.096986832 seconds Reactions :0.010976163 seconds Misc :0.010813349 seconds Base State :0.002373265 seconds Time to advance time step: 0.556188395 Call to estdt for level 0 gives dt_lev = 0.3128878797 Minimum estdt over all levels = 0.3128878797 Timestep 2 starts with TIME = 6.08983586e-05 DT = 6.698819446e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.050043586e-05 MLMG: Initial residual (resid0) = 3.050043586e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 2.284814624e-15, 7.491088438e-11 MLMG: Timers: Solve = 0.078793065 Iter = 0.076489338 Bottom = 0.01779391 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.059063412e-05 MLMG: Initial residual (resid0) = 5.66083759e-06 MLMG: Final Iter. 10 resid, resid/bnorm = 4.89262324e-16, 1.599386015e-11 MLMG: Timers: Solve = 0.085870985 Iter = 0.083557636 Bottom = 0.018131491 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003894013591 MLMG: Initial residual (resid0) = 0.003894013591 MLMG: Final Iter. 9 resid, resid/bnorm = 3.606381686e-15, 9.261348483e-13 MLMG: Timers: Solve = 0.083385626 Iter = 0.0813206 Bottom = 0.016679963 Done calling nodal solver Timestep 2 ends with TIME = 0.0001278865531 DT = 6.698819446e-05 Timing summary: Advection :0.246172792 seconds MAC Proj :0.190564094 seconds Nodal Proj :0.096474828 seconds Reactions :0.011320943 seconds Misc :0.008421209 seconds Base State :0.002545835 seconds Time to advance time step: 0.553047952 Call to estdt for level 0 gives dt_lev = 0.3130286362 Minimum estdt over all levels = 0.3130286362 Timestep 3 starts with TIME = 0.0001278865531 DT = 7.368701391e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.168800511e-05 MLMG: Initial residual (resid0) = 3.168800511e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 5.650713492e-16, 1.783234215e-11 MLMG: Timers: Solve = 0.086765786 Iter = 0.084455534 Bottom = 0.019165274 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.178722338e-05 MLMG: Initial residual (resid0) = 1.012935749e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 6.83364159e-16, 2.149807647e-11 MLMG: Timers: Solve = 0.085774896 Iter = 0.083465197 Bottom = 0.01808629 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004283414244 MLMG: Initial residual (resid0) = 0.004283414244 MLMG: Final Iter. 9 resid, resid/bnorm = 4.011764879e-15, 9.365811126e-13 MLMG: Timers: Solve = 0.083342836 Iter = 0.081211002 Bottom = 0.016669758 Done calling nodal solver Timestep 3 ends with TIME = 0.000201573567 DT = 7.368701391e-05 Timing summary: Advection :0.242576447 seconds MAC Proj :0.199749327 seconds Nodal Proj :0.097171242 seconds Reactions :0.009982252 seconds Misc :0.008271068 seconds Base State :0.002584849 seconds Time to advance time step: 0.557865242 Call to estdt for level 0 gives dt_lev = 0.3130285358 Minimum estdt over all levels = 0.3130285358 Timestep 4 starts with TIME = 0.000201573567 DT = 8.10557153e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.570538737e-05 MLMG: Initial residual (resid0) = 3.570538737e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 7.571110825e-16, 2.120439347e-11 MLMG: Timers: Solve = 0.08684924 Iter = 0.08452255 Bottom = 0.019111392 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.581452755e-05 MLMG: Initial residual (resid0) = 1.504387741e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 8.870129024e-16, 2.476684639e-11 MLMG: Timers: Solve = 0.085809089 Iter = 0.083510183 Bottom = 0.01811668 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004711755907 MLMG: Initial residual (resid0) = 0.004711755907 MLMG: Final Iter. 9 resid, resid/bnorm = 4.409450235e-15, 9.358401247e-13 MLMG: Timers: Solve = 0.083228139 Iter = 0.081178059 Bottom = 0.016660829 Done calling nodal solver Timestep 4 ends with TIME = 0.0002826292823 DT = 8.10557153e-05 Timing summary: Advection :0.246522811 seconds MAC Proj :0.19909347 seconds Nodal Proj :0.095614019 seconds Reactions :0.0104864 seconds Misc :0.007727645 seconds Base State :0.002544816 seconds Time to advance time step: 0.559538364 Call to estdt for level 0 gives dt_lev = 0.313028505 Minimum estdt over all levels = 0.313028505 Timestep 5 starts with TIME = 0.0002826292823 DT = 8.916128683e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.013180326e-05 MLMG: Initial residual (resid0) = 4.013180326e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 9.681425651e-16, 2.412407334e-11 MLMG: Timers: Solve = 0.086683816 Iter = 0.084347003 Bottom = 0.01901785 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.025185749e-05 MLMG: Initial residual (resid0) = 2.044985444e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 1.11103787e-15, 2.760215154e-11 MLMG: Timers: Solve = 0.085918206 Iter = 0.083606577 Bottom = 0.018125423 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.005182931902 MLMG: Initial residual (resid0) = 0.005182931902 MLMG: Final Iter. 9 resid, resid/bnorm = 4.819929178e-15, 9.29961896e-13 MLMG: Timers: Solve = 0.08325981 Iter = 0.081190253 Bottom = 0.01666058 Done calling nodal solver Timestep 5 ends with TIME = 0.0003717905691 DT = 8.916128683e-05 Timing summary: Advection :0.24696342 seconds MAC Proj :0.19852892 seconds Nodal Proj :0.097122505 seconds Reactions :0.010045165 seconds Misc :0.009044487 seconds Base State :0.002411824 seconds Time to advance time step: 0.561799397 Writing plotfile 5 Time to write plotfile: 0.083174572 Total Time: 4.205573433 Unused ParmParse Variables: [TOP]::maestro.v(nvals = 1) :: [1] [TOP]::amr.ref_ratio(nvals = 4) :: [2, 2, 2, 2] [TOP]::amr.check_file(nvals = 1) :: [RT_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] Total GPU global memory (MB): 12066 Free GPU global memory (MB): 10470 [The Arena] space (MB): 9049 [The Device Arena] space (MB): 8 [The Managed Arena] space (MB): 8 [The Pinned Arena] space (MB): 8 AMReX (19.11-273-g35857d1b94d4) finalized