Initializing CUDA... CUDA initialized with 1 GPU AMReX (20.01-76-gbea550b9152b) initialized Calling Setup() Calling ReadParameters() WARNING: burning_cutoff_density_lo not supplied in the inputs file WARNING: setting burning_cutoff_density_lo = base_cutoff_density reading extern runtime parameters ... ERROR: problem in the namelist Calling VariableSetup() Calling set_method_params() Initializing Helmholtz EOS and using Coulomb corrections. Calling BCSetup() Calling init_base_state_geometry() Calling Init() Calling InitData() ------------------------------------------------------------------------------ reading initial model 640 points found in the initial model file 6 variables found in the initial model file ------------------------------------------------------------------------------ model file mapping, level: 0 dr of MAESTRO base state = 562500.0000 dr of input file data = 562500.0000 maximum radius (cell-centered) of input model = 359718750.0 setting r_cutoff to 365 radius at r_cutoff 205593750.0000000 Maximum HSE Error = 0.6051370840E-04 (after putting initial model into base state arrays, and for density < base_cutoff_density) ------------------------------------------------------------------------------ ------------------------------------------------------------------------------ model file mapping, level: 1 dr of MAESTRO base state = 281250.0000 dr of input file data = 562500.0000 maximum radius (cell-centered) of input model = 359718750.0 Maximum HSE Error = 0.5009359532 (after putting initial model into base state arrays, and for density < base_cutoff_density) ------------------------------------------------------------------------------ Writing plotfile reacting_bubble-2d-amr_pltInitData after InitData inner sponge: r_sp , r_tp : 0.186468750000E+09 0.224718750000E+09 Time to write plotfile: 0.255974211 inner sponge: r_sp , r_tp : 0.186468750000E+09 0.224718750000E+09 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.008574855 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile reacting_bubble-2d-amr_pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 0.186468750000E+09 0.224718750000E+09 Time to write plotfile: 0.226199541 Call to firstdt for level 0 gives dt_lev = 0.0004741795922 Multiplying dt_lev by init_shrink; dt_lev = 0.0004741795922 Call to firstdt for level 1 gives dt_lev = 0.0002743178815 Multiplying dt_lev by init_shrink; dt_lev = 0.0002743178815 Minimum firstdt over all levels = 0.0002743178815 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 9701.829892 MLMG: Initial residual (resid0) = 9701.829892 MLMG: Final Iter. 5 resid, resid/bnorm = 0.0001318674098, 1.359201421e-08 MLMG: Timers: Solve = 0.107363573 Iter = 0.099645426 Bottom = 0.011074492 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.1641628699 Call to estdt for level 1 gives dt_lev = 0.1158500464 Minimum estdt over all levels = 0.1158500464 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.1158500464 Multiplying dt by init_shrink; dt = 0.1158500464 Ignoring this new dt since it's larger than the previous dt = 0.0002743178815 Writing plotfile reacting_bubble-2d-amr_pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 0.186468750000E+09 0.224718750000E+09 Time to write plotfile: 0.222760945 Doing initial pressure iteration #1 Timestep 0 starts with TIME = 0 DT = 0.0002743178815 Cell Count: Level 0, 245760 cells Level 1, 79872 cells inner sponge: r_sp , r_tp : 0.186468750000E+09 0.224718750000E+09 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>>