Initializing CUDA... CUDA initialized with 1 GPU AMReX (20.02-280-g98a6acf6a9b1) initialized Calling Setup() Calling ReadParameters() WARNING: burning_cutoff_density_lo not supplied in the inputs file WARNING: setting burning_cutoff_density_lo = base_cutoff_density reading extern runtime parameters ... ERROR: problem in the namelist Calling VariableSetup() Calling set_method_params() Initializing Helmholtz EOS and using Coulomb corrections. Calling BCSetup() Calling init_base_state_geometry() Calling Init() Calling InitData() ------------------------------------------------------------------------------ reading initial model 640 points found in the initial model file 6 variables found in the initial model file ------------------------------------------------------------------------------ model file mapping, level: 0 dr of MAESTRO base state = 562500.0000 dr of input file data = 562500.0000 maximum radius (cell-centered) of input model = 359718750.0 setting r_cutoff to 365 radius at r_cutoff 205593750.0000000 Maximum HSE Error = 0.6051370840E-04 (after putting initial model into base state arrays, and for density < base_cutoff_density) ------------------------------------------------------------------------------ Writing plotfile reacting_bubble-3d_pltInitData after InitData inner sponge: r_sp , r_tp : 0.186468750000E+09 0.224718750000E+09 Time to write plotfile: 0.865101302 inner sponge: r_sp , r_tp : 0.186468750000E+09 0.224718750000E+09 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.0161822 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile reacting_bubble-3d_pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 0.186468750000E+09 0.224718750000E+09 Time to write plotfile: 0.85386224 Call to firstdt for level 0 gives dt_lev = 0.0004741795139 Multiplying dt_lev by init_shrink; dt_lev = 0.0004741795139 Minimum firstdt over all levels = 0.0004741795139 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 2054.812696 MLMG: Initial residual (resid0) = 2054.812696 MLMG: Final Iter. 8 resid, resid/bnorm = 8.007106089e-11, 3.896757162e-14 MLMG: Timers: Solve = 0.223931006 Iter = 0.210308713 Bottom = 0.117997326 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.1719927642 Minimum estdt over all levels = 0.1719927642 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.1719927642 Multiplying dt by init_shrink; dt = 0.1719927642 Ignoring this new dt since it's larger than the previous dt = 0.0004741795139 Writing plotfile reacting_bubble-3d_pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 0.186468750000E+09 0.224718750000E+09 Time to write plotfile: 0.794266163 Doing initial pressure iteration #1 Timestep 0 starts with TIME = 0 DT = 0.0004741795139 Cell Count: Level 0, 1327104 cells inner sponge: r_sp , r_tp : 0.186468750000E+09 0.224718750000E+09 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2728631.974 MLMG: Initial residual (resid0) = 2728631.974 MLMG: Final Iter. 9 resid, resid/bnorm = 1.628487371e-05, 5.968145894e-12 MLMG: Timers: Solve = 0.225829013 Iter = 0.219001041 Bottom = 0.162656988 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>>