Initializing CUDA... CUDA initialized with 1 GPU AMReX (21.11-24-g301856291765) initialized Calling Setup() Calling ReadParameters() WARNING: burning_cutoff_density_lo not supplied in the inputs file WARNING: setting burning_cutoff_density_lo = base_cutoff_density reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = cutoff densities: low density cutoff (for mapping the model) = 1e-10 buoyancy cutoff density (for zeroing rho - rho_0, centrifugal term) = 5e-10 anelastic cutoff = 1e-10 Maximum HSE Error = 4.547473509e-13 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile RT_pltInitData after InitData Time to write plotfile: 0.060011871 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.008417338 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile RT_pltafter_InitProj after InitProj Time to write plotfile: 0.056104974 Call to firstdt for level 0 gives dt_lev = 0.0006089835859 Multiplying dt_lev by init_shrink; dt_lev = 6.089835859e-05 Minimum firstdt over all levels = 6.089835859e-05 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.00819542 Iter = 0 Bottom = 0 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.08660444773 Minimum estdt over all levels = 0.08660444773 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.08660444773 Multiplying dt by init_shrink; dt = 0.008660444773 Ignoring this new dt since it's larger than the previous dt = 6.089835859e-05 Writing plotfile RT_pltafter_DivuIter after final DivuIter Time to write plotfile: 0.051178531 Doing initial pressure iteration #1 Timestep 0 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 0.002421164472 MLMG: Initial residual (resid0) = 0.002421164472 MLMG: Final Iter. 9 resid, resid/bnorm = 1.751907786e-13, 7.235806598e-11 MLMG: Timers: Solve = 0.05585739 Iter = 0.053897546 Bottom = 0.019181857 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 0.002421205691 MLMG: Initial residual (resid0) = 2.151449931e-06 MLMG: Final Iter. 7 resid, resid/bnorm = 9.927907937e-14, 4.100398398e-11 MLMG: Timers: Solve = 0.041395144 Iter = 0.03961976 Bottom = 0.013702368 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 58.12657035 MLMG: Initial residual (resid0) = 58.12657035 MLMG: Final Iter. 7 resid, resid/bnorm = 8.654410522e-12, 1.488890617e-13 MLMG: Timers: Solve = 0.437771071 Iter = 0.4294714 Bottom = 0.001281047 Done calling nodal solver Timestep 0 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.293641156 seconds MAC Proj :0.107060004 seconds Nodal Proj :0.472639512 seconds Reactions :0.014153161 seconds Misc :0.014609538 seconds Base State :0.015744377 seconds Time to advance time step: 0.902301247 Writing plotfile 0 after all initialization Time to write plotfile: 0.054617342 Calling Evolve() Timestep 1 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.394238647e-05 MLMG: Initial residual (resid0) = 2.394238647e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 3.182009446e-16, 1.329027685e-11 MLMG: Timers: Solve = 0.055204887 Iter = 0.05228712 Bottom = 0.01927094 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.394218844e-05 MLMG: Initial residual (resid0) = 1.928423512e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 6.036513706e-16, 2.521287359e-11 MLMG: Timers: Solve = 0.051624909 Iter = 0.049813523 Bottom = 0.016755383 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003539812449 MLMG: Initial residual (resid0) = 0.003539812449 MLMG: Final Iter. 7 resid, resid/bnorm = 5.385232191e-16, 1.521332632e-13 MLMG: Timers: Solve = 0.438014322 Iter = 0.429736402 Bottom = 0.00156709 Done calling nodal solver Timestep 1 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.314266725 seconds MAC Proj :0.115916886 seconds Nodal Proj :0.472364011 seconds Reactions :0.013956619 seconds Misc :0.014360121 seconds Base State :0.016034089 seconds Time to advance time step: 0.931075947 Call to estdt for level 0 gives dt_lev = 0.3128878797 Minimum estdt over all levels = 0.3128878797 Call to estdt at beginning of step 2 gives dt =0.3128878797 dt_growth factor limits the new dt = 6.698819445e-05 Timestep 2 starts with TIME = 6.089835859e-05 DT = 6.698819445e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.050043585e-05 MLMG: Initial residual (resid0) = 3.050043585e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 2.617769743e-15, 8.582728966e-11 MLMG: Timers: Solve = 0.058240486 Iter = 0.055255012 Bottom = 0.018692312 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.058937698e-05 MLMG: Initial residual (resid0) = 3.366932436e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 1.074457033e-15, 3.51251689e-11 MLMG: Timers: Solve = 0.052267037 Iter = 0.050504777 Bottom = 0.017404845 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003894011863 MLMG: Initial residual (resid0) = 0.003894011863 MLMG: Final Iter. 7 resid, resid/bnorm = 5.887217797e-16, 1.511864371e-13 MLMG: Timers: Solve = 0.438642034 Iter = 0.429846777 Bottom = 0.001305133 Done calling nodal solver Timestep 2 ends with TIME = 0.000127886553 DT = 6.698819445e-05 Timing summary: Advection :0.315227147 seconds MAC Proj :0.119113987 seconds Nodal Proj :0.470310875 seconds Reactions :0.013592366 seconds Misc :0.014605205 seconds Base State :0.014470287 seconds Time to advance time step: 0.933201458 Call to estdt for level 0 gives dt_lev = 0.3130343729 Minimum estdt over all levels = 0.3130343729 Call to estdt at beginning of step 3 gives dt =0.3130343729 dt_growth factor limits the new dt = 7.36870139e-05 Timestep 3 starts with TIME = 0.000127886553 DT = 7.36870139e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.95509247e-05 MLMG: Initial residual (resid0) = 3.95509247e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 3.720068821e-15, 9.405769521e-11 MLMG: Timers: Solve = 0.058617072 Iter = 0.055829348 Bottom = 0.019038812 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.959539493e-05 MLMG: Initial residual (resid0) = 1.25524138e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 9.441732267e-16, 2.384553124e-11 MLMG: Timers: Solve = 0.05343446 Iter = 0.051633326 Bottom = 0.018557269 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004283412997 MLMG: Initial residual (resid0) = 0.004283412997 MLMG: Final Iter. 7 resid, resid/bnorm = 6.403298031e-16, 1.494905589e-13 MLMG: Timers: Solve = 0.43647398 Iter = 0.428164643 Bottom = 0.001606093 Done calling nodal solver Timestep 3 ends with TIME = 0.0002015735669 DT = 7.36870139e-05 Timing summary: Advection :0.297327633 seconds MAC Proj :0.120524328 seconds Nodal Proj :0.470202624 seconds Reactions :0.012841195 seconds Misc :0.017619387 seconds Base State :0.014766748 seconds Time to advance time step: 0.918723629 Call to estdt for level 0 gives dt_lev = 0.3130323766 Minimum estdt over all levels = 0.3130323766 Call to estdt at beginning of step 4 gives dt =0.3130323766 dt_growth factor limits the new dt = 8.105571529e-05 Timestep 4 starts with TIME = 0.0002015735669 DT = 8.105571529e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.584764586e-05 MLMG: Initial residual (resid0) = 5.584764586e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 4.629171058e-15, 8.288927828e-11 MLMG: Timers: Solve = 0.058485154 Iter = 0.055519139 Bottom = 0.018853228 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.589656386e-05 MLMG: Initial residual (resid0) = 8.595300417e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 1.48844187e-15, 2.662850393e-11 MLMG: Timers: Solve = 0.053477252 Iter = 0.051680408 Bottom = 0.01847606 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004711754539 MLMG: Initial residual (resid0) = 0.004711754539 MLMG: Final Iter. 7 resid, resid/bnorm = 6.810958048e-16, 1.445524802e-13 MLMG: Timers: Solve = 0.431029659 Iter = 0.422996989 Bottom = 0.001203048 Done calling nodal solver Timestep 4 ends with TIME = 0.0002826292822 DT = 8.105571529e-05 Timing summary: Advection :0.2870317 seconds MAC Proj :0.120972957 seconds Nodal Proj :0.464812093 seconds Reactions :0.013705783 seconds Misc :0.015923962 seconds Base State :0.015445584 seconds Time to advance time step: 0.902644207 Call to estdt for level 0 gives dt_lev = 0.3130323437 Minimum estdt over all levels = 0.3130323437 Call to estdt at beginning of step 5 gives dt =0.3130323437 dt_growth factor limits the new dt = 8.916128682e-05 Timestep 5 starts with TIME = 0.0002826292822 DT = 8.916128682e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.377430078e-05 MLMG: Initial residual (resid0) = 7.377430078e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 5.790846544e-15, 7.849408916e-11 MLMG: Timers: Solve = 0.058176445 Iter = 0.05538943 Bottom = 0.018704688 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.382811062e-05 MLMG: Initial residual (resid0) = 1.227093904e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 2.001098397e-15, 2.710483013e-11 MLMG: Timers: Solve = 0.053284167 Iter = 0.051511616 Bottom = 0.018274225 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.005182930403 MLMG: Initial residual (resid0) = 0.005182930403 MLMG: Final Iter. 7 resid, resid/bnorm = 7.38124839e-16, 1.424145766e-13 MLMG: Timers: Solve = 0.438065072 Iter = 0.429583318 Bottom = 0.001818385 Done calling nodal solver Timestep 5 ends with TIME = 0.000371790569 DT = 8.916128682e-05 Timing summary: Advection :0.306571767 seconds MAC Proj :0.119827699 seconds Nodal Proj :0.469227702 seconds Reactions :0.013454323 seconds Misc :0.016628299 seconds Base State :0.016324465 seconds Time to advance time step: 0.92593121 Writing plotfile 5 Time to write plotfile: 0.054457341 Total Time: 5.945675734 Unused ParmParse Variables: [TOP]::maestro.v(nvals = 1) :: [1] [TOP]::amr.ref_ratio(nvals = 4) :: [2, 2, 2, 2] [TOP]::amr.check_file(nvals = 1) :: [RT_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] Total GPU global memory (MB): 12066 Free GPU global memory (MB): 11392 [The Arena] space allocated (MB): 9049 [The Arena] space used (MB): 0 [The Pinned Arena] space allocated (MB): 8 [The Pinned Arena] space used (MB): 0 AMReX (21.11-24-g301856291765) finalized