Initializing CUDA... CUDA initialized with 1 GPU AMReX (22.09-1-gfb0b31e1439b) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = cutoff densities: low density cutoff (for mapping the model) = 1e-10 buoyancy cutoff density (for zeroing rho - rho_0, centrifugal term) = 5e-10 anelastic cutoff = 1e-10 Maximum HSE Error = 4.547473509e-13 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile RT_pltInitData after InitData Time to write plotfile: 0.068324461 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.005739777 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile RT_pltafter_InitProj after InitProj Time to write plotfile: 0.060911113 Call to firstdt for level 0 gives dt_lev = 0.0006089835859 Multiplying dt_lev by init_shrink; dt_lev = 6.089835859e-05 Minimum firstdt over all levels = 6.089835859e-05 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.005520159 Iter = 0 Bottom = 0 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.08660444773 Minimum estdt over all levels = 0.08660444773 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.08660444773 Multiplying dt by init_shrink; dt = 0.008660444773 Ignoring this new dt since it's larger than the previous dt = 6.089835859e-05 Writing plotfile RT_pltafter_DivuIter after final DivuIter Time to write plotfile: 0.056209703 Doing initial pressure iteration #1 Timestep 0 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 0.002421164472 MLMG: Initial residual (resid0) = 0.002421164472 MLMG: Final Iter. 9 resid, resid/bnorm = 1.751907753e-13, 7.235806461e-11 MLMG: Timers: Solve = 0.047933644 Iter = 0.046129979 Bottom = 0.016457581 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 0.002421205691 MLMG: Initial residual (resid0) = 2.151449931e-06 MLMG: Final Iter. 7 resid, resid/bnorm = 9.927908543e-14, 4.100398648e-11 MLMG: Timers: Solve = 0.036672803 Iter = 0.035028782 Bottom = 0.011949531 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 58.12657035 MLMG: Initial residual (resid0) = 58.12657035 MLMG: Final Iter. 7 resid, resid/bnorm = 8.824940778e-12, 1.518228364e-13 MLMG: Timers: Solve = 0.408017049 Iter = 0.402078435 Bottom = 0.003822294 Done calling nodal solver Timestep 0 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.250925632 seconds MAC Proj :0.093788814 seconds Nodal Proj :0.434099789 seconds Reactions :0.010644922 seconds Misc :0.013741054 seconds Base State :0.015103493 seconds Time to advance time step: 0.803364924 Writing plotfile 0 after all initialization Time to write plotfile: 0.081950499 Calling Evolve() Timestep 1 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.394238647e-05 MLMG: Initial residual (resid0) = 2.394238647e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 3.182067635e-16, 1.329051988e-11 MLMG: Timers: Solve = 0.049437751 Iter = 0.046763432 Bottom = 0.017147201 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.394218844e-05 MLMG: Initial residual (resid0) = 1.928423558e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 6.036513706e-16, 2.521287359e-11 MLMG: Timers: Solve = 0.045946846 Iter = 0.044173046 Bottom = 0.014672126 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003539812449 MLMG: Initial residual (resid0) = 0.003539812449 MLMG: Final Iter. 7 resid, resid/bnorm = 5.352706126e-16, 1.512143991e-13 MLMG: Timers: Solve = 0.410029636 Iter = 0.403746755 Bottom = 0.002734509 Done calling nodal solver Timestep 1 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.262743114 seconds MAC Proj :0.103599247 seconds Nodal Proj :0.436441079 seconds Reactions :0.009938217 seconds Misc :0.015219034 seconds Base State :0.014298095 seconds Time to advance time step: 0.828117041 Call to estdt for level 0 gives dt_lev = 0.3128878797 Minimum estdt over all levels = 0.3128878797 Call to estdt at beginning of step 2 gives dt =0.3128878797 dt_growth factor limits the new dt = 6.698819445e-05 Timestep 2 starts with TIME = 6.089835859e-05 DT = 6.698819445e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.050043585e-05 MLMG: Initial residual (resid0) = 3.050043585e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 2.617769736e-15, 8.582728945e-11 MLMG: Timers: Solve = 0.052100838 Iter = 0.049292867 Bottom = 0.016439677 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.058937698e-05 MLMG: Initial residual (resid0) = 3.366932436e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 1.074458114e-15, 3.512520424e-11 MLMG: Timers: Solve = 0.046307875 Iter = 0.044664712 Bottom = 0.015168186 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003894011863 MLMG: Initial residual (resid0) = 0.003894011863 MLMG: Final Iter. 7 resid, resid/bnorm = 5.814576251e-16, 1.493209691e-13 MLMG: Timers: Solve = 0.411009661 Iter = 0.405752366 Bottom = 0.002831468 Done calling nodal solver Timestep 2 ends with TIME = 0.000127886553 DT = 6.698819445e-05 Timing summary: Advection :0.259877074 seconds MAC Proj :0.107000474 seconds Nodal Proj :0.435629609 seconds Reactions :0.009410628 seconds Misc :0.018118855 seconds Base State :0.020355696 seconds Time to advance time step: 0.830204616 Call to estdt for level 0 gives dt_lev = 0.3130343729 Minimum estdt over all levels = 0.3130343729 Call to estdt at beginning of step 3 gives dt =0.3130343729 dt_growth factor limits the new dt = 7.36870139e-05 Timestep 3 starts with TIME = 0.000127886553 DT = 7.36870139e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.955092471e-05 MLMG: Initial residual (resid0) = 3.955092471e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 3.720066743e-15, 9.405764264e-11 MLMG: Timers: Solve = 0.052079689 Iter = 0.049313221 Bottom = 0.016596481 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.959539494e-05 MLMG: Initial residual (resid0) = 1.25524138e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 9.441723797e-16, 2.384550984e-11 MLMG: Timers: Solve = 0.047563026 Iter = 0.045852965 Bottom = 0.016283442 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004283412997 MLMG: Initial residual (resid0) = 0.004283412997 MLMG: Final Iter. 7 resid, resid/bnorm = 6.398961222e-16, 1.493893124e-13 MLMG: Timers: Solve = 0.407975565 Iter = 0.401781273 Bottom = 0.002896255 Done calling nodal solver Timestep 3 ends with TIME = 0.0002015735669 DT = 7.36870139e-05 Timing summary: Advection :0.267707817 seconds MAC Proj :0.10778029 seconds Nodal Proj :0.434491826 seconds Reactions :0.00948538 seconds Misc :0.018929754 seconds Base State :0.019923562 seconds Time to advance time step: 0.838563167 Call to estdt for level 0 gives dt_lev = 0.3130323766 Minimum estdt over all levels = 0.3130323766 Call to estdt at beginning of step 4 gives dt =0.3130323766 dt_growth factor limits the new dt = 8.105571529e-05 Timestep 4 starts with TIME = 0.0002015735669 DT = 8.105571529e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.584764588e-05 MLMG: Initial residual (resid0) = 5.584764588e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 4.629174129e-15, 8.288933322e-11 MLMG: Timers: Solve = 0.052052694 Iter = 0.049253658 Bottom = 0.016558247 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.589656388e-05 MLMG: Initial residual (resid0) = 8.595300417e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 1.48844187e-15, 2.662850392e-11 MLMG: Timers: Solve = 0.047130577 Iter = 0.045476127 Bottom = 0.015942842 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004711754539 MLMG: Initial residual (resid0) = 0.004711754539 MLMG: Final Iter. 7 resid, resid/bnorm = 7.175249978e-16, 1.52284036e-13 MLMG: Timers: Solve = 0.41571349 Iter = 0.410256196 Bottom = 0.002644271 Done calling nodal solver Timestep 4 ends with TIME = 0.0002826292822 DT = 8.105571529e-05 Timing summary: Advection :0.26047194 seconds MAC Proj :0.10702124 seconds Nodal Proj :0.442531332 seconds Reactions :0.009322172 seconds Misc :0.017422308 seconds Base State :0.016833976 seconds Time to advance time step: 0.837023905 Call to estdt for level 0 gives dt_lev = 0.3130323437 Minimum estdt over all levels = 0.3130323437 Call to estdt at beginning of step 5 gives dt =0.3130323437 dt_growth factor limits the new dt = 8.916128682e-05 Timestep 5 starts with TIME = 0.0002826292822 DT = 8.916128682e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.377430081e-05 MLMG: Initial residual (resid0) = 7.377430081e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 5.790841488e-15, 7.84940206e-11 MLMG: Timers: Solve = 0.052000519 Iter = 0.049274798 Bottom = 0.016476981 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.382811065e-05 MLMG: Initial residual (resid0) = 1.227093904e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 2.001096703e-15, 2.710480717e-11 MLMG: Timers: Solve = 0.04713844 Iter = 0.04550533 Bottom = 0.01596745 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.005182930403 MLMG: Initial residual (resid0) = 0.005182930403 MLMG: Final Iter. 7 resid, resid/bnorm = 7.684824999e-16, 1.482718154e-13 MLMG: Timers: Solve = 0.407963715 Iter = 0.401071773 Bottom = 0.002731938 Done calling nodal solver Timestep 5 ends with TIME = 0.000371790569 DT = 8.916128682e-05 Timing summary: Advection :0.244941831 seconds MAC Proj :0.107261285 seconds Nodal Proj :0.434803649 seconds Reactions :0.009766672 seconds Misc :0.018820651 seconds Base State :0.012728111 seconds Time to advance time step: 0.815841908 Writing plotfile 5 Time to write plotfile: 0.059003207 Total Time: 5.412529531 Unused ParmParse Variables: [TOP]::maestro.v(nvals = 1) :: [1] [TOP]::amr.ref_ratio(nvals = 4) :: [2, 2, 2, 2] [TOP]::amr.check_file(nvals = 1) :: [RT_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] Total GPU global memory (MB): 12066 Free GPU global memory (MB): 11391 [The Arena] space allocated (MB): 9049 [The Arena] space used (MB): 0 [The Pinned Arena] space allocated (MB): 8 [The Pinned Arena] space used (MB): 0 AMReX (22.09-1-gfb0b31e1439b) finalized