Initializing CUDA... CUDA initialized with 1 device. AMReX (23.01-15-gf972714bd111) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = cutoff densities: low density cutoff (for mapping the model) = 1e-10 buoyancy cutoff density (for zeroing rho - rho_0, centrifugal term) = 5e-10 anelastic cutoff = 1e-10 Maximum HSE Error = 4.547473509e-13 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile RT_pltInitData after InitData Time to write plotfile: 0.070474722 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.005875255 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile RT_pltafter_InitProj after InitProj Time to write plotfile: 0.065021359 Call to firstdt for level 0 gives dt_lev = 0.0006089835859 Multiplying dt_lev by init_shrink; dt_lev = 6.089835859e-05 Minimum firstdt over all levels = 6.089835859e-05 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.005539548 Iter = 0 Bottom = 0 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.08660444773 Minimum estdt over all levels = 0.08660444773 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.08660444773 Multiplying dt by init_shrink; dt = 0.008660444773 Ignoring this new dt since it's larger than the previous dt = 6.089835859e-05 Writing plotfile RT_pltafter_DivuIter after final DivuIter Time to write plotfile: 0.057569391 Doing initial pressure iteration #1 Timestep 0 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 0.002421164472 MLMG: Initial residual (resid0) = 0.002421164472 MLMG: Final Iter. 9 resid, resid/bnorm = 1.751907853e-13, 7.235806877e-11 MLMG: Timers: Solve = 0.0497681 Iter = 0.048036897 Bottom = 0.016293579 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 0.002421205691 MLMG: Initial residual (resid0) = 2.151449931e-06 MLMG: Final Iter. 7 resid, resid/bnorm = 9.927909263e-14, 4.100398946e-11 MLMG: Timers: Solve = 0.036772178 Iter = 0.03517673 Bottom = 0.011417086 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 58.12657035 MLMG: Initial residual (resid0) = 58.12657035 MLMG: Final Iter. 7 resid, resid/bnorm = 8.881784197e-12, 1.528007612e-13 MLMG: Timers: Solve = 0.408012057 Iter = 0.401842457 Bottom = 0.002070738 Done calling nodal solver Timestep 0 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.217518077 seconds MAC Proj :0.09466314 seconds Nodal Proj :0.428319321 seconds Reactions :0.006696962 seconds Misc :0.012594864 seconds Base State :0.010298543 seconds Time to advance time step: 0.759943963 Writing plotfile 0 after all initialization Time to write plotfile: 0.060055176 Calling Evolve() Timestep 1 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.394238647e-05 MLMG: Initial residual (resid0) = 2.394238647e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 3.18471626e-16, 1.330158238e-11 MLMG: Timers: Solve = 0.048179793 Iter = 0.04608781 Bottom = 0.015907647 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.394218844e-05 MLMG: Initial residual (resid0) = 1.928423197e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 6.036513706e-16, 2.521287359e-11 MLMG: Timers: Solve = 0.045552404 Iter = 0.043953801 Bottom = 0.013888094 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003539812449 MLMG: Initial residual (resid0) = 0.003539812449 MLMG: Final Iter. 7 resid, resid/bnorm = 5.166223352e-16, 1.459462451e-13 MLMG: Timers: Solve = 0.406629536 Iter = 0.400506269 Bottom = 0.001180709 Done calling nodal solver Timestep 1 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.197633633 seconds MAC Proj :0.101138639 seconds Nodal Proj :0.428607343 seconds Reactions :0.006172138 seconds Misc :0.012210172 seconds Base State :0.01173171 seconds Time to advance time step: 0.745921253 Call to estdt for level 0 gives dt_lev = 0.3128878797 Minimum estdt over all levels = 0.3128878797 Call to estdt at beginning of step 2 gives dt =0.3128878797 dt_growth factor limits the new dt = 6.698819445e-05 Timestep 2 starts with TIME = 6.089835859e-05 DT = 6.698819445e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.050043585e-05 MLMG: Initial residual (resid0) = 3.050043585e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 2.61777012e-15, 8.582730203e-11 MLMG: Timers: Solve = 0.050980112 Iter = 0.048838618 Bottom = 0.015470476 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.058937698e-05 MLMG: Initial residual (resid0) = 3.366932437e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 1.074457716e-15, 3.512519124e-11 MLMG: Timers: Solve = 0.046033118 Iter = 0.044442488 Bottom = 0.014331803 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003894011863 MLMG: Initial residual (resid0) = 0.003894011863 MLMG: Final Iter. 7 resid, resid/bnorm = 5.805902634e-16, 1.490982266e-13 MLMG: Timers: Solve = 0.410281511 Iter = 0.404049752 Bottom = 0.001244569 Done calling nodal solver Timestep 2 ends with TIME = 0.000127886553 DT = 6.698819445e-05 Timing summary: Advection :0.205993594 seconds MAC Proj :0.104589986 seconds Nodal Proj :0.428268204 seconds Reactions :0.006448047 seconds Misc :0.011019291 seconds Base State :0.010933664 seconds Time to advance time step: 0.756519912 Call to estdt for level 0 gives dt_lev = 0.3130343729 Minimum estdt over all levels = 0.3130343729 Call to estdt at beginning of step 3 gives dt =0.3130343729 dt_growth factor limits the new dt = 7.36870139e-05 Timestep 3 starts with TIME = 0.000127886553 DT = 7.36870139e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.955092471e-05 MLMG: Initial residual (resid0) = 3.955092471e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 3.720066955e-15, 9.405764801e-11 MLMG: Timers: Solve = 0.051195955 Iter = 0.049069225 Bottom = 0.01566061 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.959539493e-05 MLMG: Initial residual (resid0) = 1.25524138e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 9.441723797e-16, 2.384550985e-11 MLMG: Timers: Solve = 0.047027485 Iter = 0.045416463 Bottom = 0.015254132 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004283412997 MLMG: Initial residual (resid0) = 0.004283412997 MLMG: Final Iter. 7 resid, resid/bnorm = 6.496539418e-16, 1.516673602e-13 MLMG: Timers: Solve = 0.404402703 Iter = 0.398142942 Bottom = 0.001227836 Done calling nodal solver Timestep 3 ends with TIME = 0.0002015735669 DT = 7.36870139e-05 Timing summary: Advection :0.221452271 seconds MAC Proj :0.106254143 seconds Nodal Proj :0.427751747 seconds Reactions :0.006213613 seconds Misc :0.016511573 seconds Base State :0.015932298 seconds Time to advance time step: 0.778373971 Call to estdt for level 0 gives dt_lev = 0.3130323766 Minimum estdt over all levels = 0.3130323766 Call to estdt at beginning of step 4 gives dt =0.3130323766 dt_growth factor limits the new dt = 8.105571529e-05 Timestep 4 starts with TIME = 0.0002015735669 DT = 8.105571529e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.584764586e-05 MLMG: Initial residual (resid0) = 5.584764586e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 4.629173467e-15, 8.28893214e-11 MLMG: Timers: Solve = 0.051813049 Iter = 0.04903591 Bottom = 0.015609885 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.589656387e-05 MLMG: Initial residual (resid0) = 8.595300418e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 1.48844187e-15, 2.662850392e-11 MLMG: Timers: Solve = 0.04673066 Iter = 0.045131438 Bottom = 0.01501904 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004711754539 MLMG: Initial residual (resid0) = 0.004711754539 MLMG: Final Iter. 7 resid, resid/bnorm = 7.272828173e-16, 1.543549884e-13 MLMG: Timers: Solve = 0.410246217 Iter = 0.404748132 Bottom = 0.003123479 Done calling nodal solver Timestep 4 ends with TIME = 0.0002826292822 DT = 8.105571529e-05 Timing summary: Advection :0.243661009 seconds MAC Proj :0.106268625 seconds Nodal Proj :0.435682667 seconds Reactions :0.009410161 seconds Misc :0.017410495 seconds Base State :0.017721422 seconds Time to advance time step: 0.812621503 Call to estdt for level 0 gives dt_lev = 0.3130323437 Minimum estdt over all levels = 0.3130323437 Call to estdt at beginning of step 5 gives dt =0.3130323437 dt_growth factor limits the new dt = 8.916128682e-05 Timestep 5 starts with TIME = 0.0002826292822 DT = 8.916128682e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.377430079e-05 MLMG: Initial residual (resid0) = 7.377430079e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 5.790845644e-15, 7.849407696e-11 MLMG: Timers: Solve = 0.051554545 Iter = 0.048876096 Bottom = 0.015489901 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.382811063e-05 MLMG: Initial residual (resid0) = 1.227093904e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 2.001098397e-15, 2.710483013e-11 MLMG: Timers: Solve = 0.046861993 Iter = 0.045230774 Bottom = 0.015032193 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.005182930403 MLMG: Initial residual (resid0) = 0.005182930403 MLMG: Final Iter. 7 resid, resid/bnorm = 7.628446486e-16, 1.471840425e-13 MLMG: Timers: Solve = 0.404786369 Iter = 0.397995553 Bottom = 0.001368899 Done calling nodal solver Timestep 5 ends with TIME = 0.000371790569 DT = 8.916128682e-05 Timing summary: Advection :0.249108613 seconds MAC Proj :0.10662214 seconds Nodal Proj :0.42913368 seconds Reactions :0.009251797 seconds Misc :0.017662808 seconds Base State :0.015737313 seconds Time to advance time step: 0.811974609 Writing plotfile 5 Time to write plotfile: 0.062286818 Total Time: 5.093800018 Unused ParmParse Variables: [TOP]::maestro.v(nvals = 1) :: [1] [TOP]::amr.ref_ratio(nvals = 4) :: [2, 2, 2, 2] [TOP]::amr.check_file(nvals = 1) :: [RT_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] Total GPU global memory (MB): 12056 Free GPU global memory (MB): 11371 [The Arena] space allocated (MB): 9042 [The Arena] space used (MB): 0 [The Device Arena] space allocated (MB): 8 [The Device Arena] space used (MB): 0 [The Pinned Arena] space allocated (MB): 8 [The Pinned Arena] space used (MB): 0 AMReX (23.01-15-gf972714bd111) finalized