Initializing CUDA... CUDA initialized with 1 device. AMReX (23.03-22-g82e38a8f5ebe) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = cutoff densities: low density cutoff (for mapping the model) = 1e-10 buoyancy cutoff density (for zeroing rho - rho_0, centrifugal term) = 5e-10 anelastic cutoff = 1e-10 Maximum HSE Error = 4.547473509e-13 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile RT_pltInitData after InitData Time to write plotfile: 0.069663399 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.005802558 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile RT_pltafter_InitProj after InitProj Time to write plotfile: 0.065815923 Call to firstdt for level 0 gives dt_lev = 0.0006089835859 Multiplying dt_lev by init_shrink; dt_lev = 6.089835859e-05 Minimum firstdt over all levels = 6.089835859e-05 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.005567697 Iter = 0 Bottom = 0 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.08660444773 Minimum estdt over all levels = 0.08660444773 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.08660444773 Multiplying dt by init_shrink; dt = 0.008660444773 Ignoring this new dt since it's larger than the previous dt = 6.089835859e-05 Writing plotfile RT_pltafter_DivuIter after final DivuIter Time to write plotfile: 0.059525246 Doing initial pressure iteration #1 Timestep 0 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 0.002421164472 MLMG: Initial residual (resid0) = 0.002421164472 MLMG: Final Iter. 9 resid, resid/bnorm = 1.751907753e-13, 7.235806461e-11 MLMG: Timers: Solve = 0.045319756 Iter = 0.043645957 Bottom = 0.014996311 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 0.002421205691 MLMG: Initial residual (resid0) = 2.151449931e-06 MLMG: Final Iter. 7 resid, resid/bnorm = 9.927909112e-14, 4.100398884e-11 MLMG: Timers: Solve = 0.034473762 Iter = 0.032943029 Bottom = 0.010792297 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 58.12657035 MLMG: Initial residual (resid0) = 58.12657035 MLMG: Final Iter. 7 resid, resid/bnorm = 8.441247701e-12, 1.452218435e-13 MLMG: Timers: Solve = 0.407019199 Iter = 0.400906058 Bottom = 0.00226197 Done calling nodal solver Timestep 0 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.260305888 seconds MAC Proj :0.088630712 seconds Nodal Proj :0.430418308 seconds Reactions :0.011258121 seconds Misc :0.014944717 seconds Base State :0.014854501 seconds Time to advance time step: 0.805740102 Writing plotfile 0 after all initialization Time to write plotfile: 0.086180431 Calling Evolve() Timestep 1 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.394238647e-05 MLMG: Initial residual (resid0) = 2.394238647e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 3.185038187e-16, 1.330292697e-11 MLMG: Timers: Solve = 0.0463344 Iter = 0.043737869 Bottom = 0.015226647 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.394218844e-05 MLMG: Initial residual (resid0) = 1.928423167e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 6.036517941e-16, 2.521289128e-11 MLMG: Timers: Solve = 0.050928677 Iter = 0.049390764 Bottom = 0.013426401 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003539812449 MLMG: Initial residual (resid0) = 0.003539812449 MLMG: Final Iter. 7 resid, resid/bnorm = 5.272475165e-16, 1.489478677e-13 MLMG: Timers: Solve = 0.403700847 Iter = 0.397425926 Bottom = 0.001258822 Done calling nodal solver Timestep 1 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.263254347 seconds MAC Proj :0.10520334 seconds Nodal Proj :0.428423057 seconds Reactions :0.010649623 seconds Misc :0.01850447 seconds Base State :0.015477679 seconds Time to advance time step: 0.826322232 Call to estdt for level 0 gives dt_lev = 0.3128878797 Minimum estdt over all levels = 0.3128878797 Call to estdt at beginning of step 2 gives dt =0.3128878797 dt_growth factor limits the new dt = 6.698819445e-05 Timestep 2 starts with TIME = 6.089835859e-05 DT = 6.698819445e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.050043585e-05 MLMG: Initial residual (resid0) = 3.050043585e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 2.617769988e-15, 8.582729769e-11 MLMG: Timers: Solve = 0.049131545 Iter = 0.046429731 Bottom = 0.014843502 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.058937698e-05 MLMG: Initial residual (resid0) = 3.366932437e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 1.074456904e-15, 3.512516467e-11 MLMG: Timers: Solve = 0.043594786 Iter = 0.04206832 Bottom = 0.013737485 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003894011863 MLMG: Initial residual (resid0) = 0.003894011863 MLMG: Final Iter. 7 resid, resid/bnorm = 5.726755875e-16, 1.470657018e-13 MLMG: Timers: Solve = 0.409907559 Iter = 0.404724236 Bottom = 0.001485508 Done calling nodal solver Timestep 2 ends with TIME = 0.000127886553 DT = 6.698819445e-05 Timing summary: Advection :0.258170452 seconds MAC Proj :0.10094043 seconds Nodal Proj :0.43437573 seconds Reactions :0.01008454 seconds Misc :0.017465388 seconds Base State :0.01692557 seconds Time to advance time step: 0.821218319 Call to estdt for level 0 gives dt_lev = 0.3130343729 Minimum estdt over all levels = 0.3130343729 Call to estdt at beginning of step 3 gives dt =0.3130343729 dt_growth factor limits the new dt = 7.36870139e-05 Timestep 3 starts with TIME = 0.000127886553 DT = 7.36870139e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.955092471e-05 MLMG: Initial residual (resid0) = 3.955092471e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 3.720067497e-15, 9.405766172e-11 MLMG: Timers: Solve = 0.049156766 Iter = 0.046579821 Bottom = 0.015029388 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.959539494e-05 MLMG: Initial residual (resid0) = 1.25524138e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 9.441732267e-16, 2.384553123e-11 MLMG: Timers: Solve = 0.044727752 Iter = 0.04317524 Bottom = 0.01474515 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004283412997 MLMG: Initial residual (resid0) = 0.004283412997 MLMG: Final Iter. 7 resid, resid/bnorm = 6.214646853e-16, 1.450863332e-13 MLMG: Timers: Solve = 0.403309041 Iter = 0.397180043 Bottom = 0.001175691 Done calling nodal solver Timestep 3 ends with TIME = 0.0002015735669 DT = 7.36870139e-05 Timing summary: Advection :0.272403642 seconds MAC Proj :0.101890268 seconds Nodal Proj :0.428463782 seconds Reactions :0.010016297 seconds Misc :0.017117661 seconds Base State :0.02151186 seconds Time to advance time step: 0.830220042 Call to estdt for level 0 gives dt_lev = 0.3130323766 Minimum estdt over all levels = 0.3130323766 Call to estdt at beginning of step 4 gives dt =0.3130323766 dt_growth factor limits the new dt = 8.105571529e-05 Timestep 4 starts with TIME = 0.0002015735669 DT = 8.105571529e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.584764588e-05 MLMG: Initial residual (resid0) = 5.584764588e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 4.629170847e-15, 8.288927445e-11 MLMG: Timers: Solve = 0.049245378 Iter = 0.046619308 Bottom = 0.015008505 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.589656388e-05 MLMG: Initial residual (resid0) = 8.595300418e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 1.488443564e-15, 2.662853423e-11 MLMG: Timers: Solve = 0.044380333 Iter = 0.042852663 Bottom = 0.014460898 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004711754539 MLMG: Initial residual (resid0) = 0.004711754539 MLMG: Final Iter. 7 resid, resid/bnorm = 7.175249978e-16, 1.52284036e-13 MLMG: Timers: Solve = 0.415172169 Iter = 0.409998076 Bottom = 0.001329302 Done calling nodal solver Timestep 4 ends with TIME = 0.0002826292822 DT = 8.105571529e-05 Timing summary: Advection :0.258583189 seconds MAC Proj :0.101602126 seconds Nodal Proj :0.442553628 seconds Reactions :0.009820112 seconds Misc :0.016960787 seconds Base State :0.016337369 seconds Time to advance time step: 0.829700305 Call to estdt for level 0 gives dt_lev = 0.3130323437 Minimum estdt over all levels = 0.3130323437 Call to estdt at beginning of step 5 gives dt =0.3130323437 dt_growth factor limits the new dt = 8.916128682e-05 Timestep 5 starts with TIME = 0.0002826292822 DT = 8.916128682e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.377430081e-05 MLMG: Initial residual (resid0) = 7.377430081e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 5.790842494e-15, 7.849403424e-11 MLMG: Timers: Solve = 0.049155514 Iter = 0.046538528 Bottom = 0.014922751 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.382811065e-05 MLMG: Initial residual (resid0) = 1.227093904e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 2.001096703e-15, 2.710480717e-11 MLMG: Timers: Solve = 0.044412936 Iter = 0.042853557 Bottom = 0.014453027 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.005182930403 MLMG: Initial residual (resid0) = 0.005182930403 MLMG: Final Iter. 7 resid, resid/bnorm = 7.821434472e-16, 1.509075728e-13 MLMG: Timers: Solve = 0.406749652 Iter = 0.401113516 Bottom = 0.001265844 Done calling nodal solver Timestep 5 ends with TIME = 0.000371790569 DT = 8.916128682e-05 Timing summary: Advection :0.276064525 seconds MAC Proj :0.101267979 seconds Nodal Proj :0.435529663 seconds Reactions :0.00995703 seconds Misc :0.017227226 seconds Base State :0.012611687 seconds Time to advance time step: 0.840322585 Writing plotfile 5 Time to write plotfile: 0.061551723 Total Time: 5.430462506 Unused ParmParse Variables: [TOP]::maestro.v(nvals = 1) :: [1] [TOP]::amr.ref_ratio(nvals = 4) :: [2, 2, 2, 2] [TOP]::amr.check_file(nvals = 1) :: [RT_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] Total GPU global memory (MB): 12056 Free GPU global memory (MB): 11371 [The Arena] space allocated (MB): 9042 [The Arena] space used (MB): 0 [The Device Arena] space allocated (MB): 8 [The Device Arena] space used (MB): 0 [The Pinned Arena] space allocated (MB): 8 [The Pinned Arena] space used (MB): 0 AMReX (23.03-22-g82e38a8f5ebe) finalized