Initializing CUDA... CUDA initialized with 1 device. AMReX (23.04-41-gcf6b46bd95a3) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = cutoff densities: low density cutoff (for mapping the model) = 1e-10 buoyancy cutoff density (for zeroing rho - rho_0, centrifugal term) = 5e-10 anelastic cutoff = 1e-10 Maximum HSE Error = 4.547473509e-13 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile RT_pltInitData after InitData Time to write plotfile: 0.069029483 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.005115234 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile RT_pltafter_InitProj after InitProj Time to write plotfile: 0.063808068 Call to firstdt for level 0 gives dt_lev = 0.0006089835859 Multiplying dt_lev by init_shrink; dt_lev = 6.089835859e-05 Minimum firstdt over all levels = 6.089835859e-05 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.005052571 Iter = 0 Bottom = 0 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.08660444773 Minimum estdt over all levels = 0.08660444773 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.08660444773 Multiplying dt by init_shrink; dt = 0.008660444773 Ignoring this new dt since it's larger than the previous dt = 6.089835859e-05 Writing plotfile RT_pltafter_DivuIter after final DivuIter Time to write plotfile: 0.059371567 Doing initial pressure iteration #1 Timestep 0 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 0.002421164472 MLMG: Initial residual (resid0) = 0.002421164472 MLMG: Final Iter. 9 resid, resid/bnorm = 1.751907807e-13, 7.235806687e-11 MLMG: Timers: Solve = 0.046836292 Iter = 0.04512289 Bottom = 0.015322084 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 0.002421205691 MLMG: Initial residual (resid0) = 2.151449931e-06 MLMG: Final Iter. 7 resid, resid/bnorm = 9.927909475e-14, 4.100399033e-11 MLMG: Timers: Solve = 0.034638324 Iter = 0.03309656 Bottom = 0.010805937 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 58.12657035 MLMG: Initial residual (resid0) = 58.12657035 MLMG: Final Iter. 7 resid, resid/bnorm = 8.654410522e-12, 1.488890617e-13 MLMG: Timers: Solve = 0.405179167 Iter = 0.399840017 Bottom = 0.002374883 Done calling nodal solver Timestep 0 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.249202667 seconds MAC Proj :0.089895994 seconds Nodal Proj :0.432239942 seconds Reactions :0.010554613 seconds Misc :0.015356312 seconds Base State :0.015643374 seconds Time to advance time step: 0.797432117 Writing plotfile 0 after all initialization Time to write plotfile: 0.116390992 Calling Evolve() Timestep 1 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.394238647e-05 MLMG: Initial residual (resid0) = 2.394238647e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 3.184282746e-16, 1.329977172e-11 MLMG: Timers: Solve = 0.045881414 Iter = 0.043444841 Bottom = 0.015067814 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.394218844e-05 MLMG: Initial residual (resid0) = 1.928423258e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 6.036517941e-16, 2.521289128e-11 MLMG: Timers: Solve = 0.049694824 Iter = 0.048072368 Bottom = 0.019516826 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003539812449 MLMG: Initial residual (resid0) = 0.003539812449 MLMG: Final Iter. 7 resid, resid/bnorm = 5.131528882e-16, 1.449661234e-13 MLMG: Timers: Solve = 0.404197241 Iter = 0.398033657 Bottom = 0.001262982 Done calling nodal solver Timestep 1 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.244441652 seconds MAC Proj :0.103490674 seconds Nodal Proj :0.43359362 seconds Reactions :0.009265606 seconds Misc :0.017019783 seconds Base State :0.015699085 seconds Time to advance time step: 0.8079858 Call to estdt for level 0 gives dt_lev = 0.3128878797 Minimum estdt over all levels = 0.3128878797 Call to estdt at beginning of step 2 gives dt =0.3128878797 dt_growth factor limits the new dt = 6.698819445e-05 Timestep 2 starts with TIME = 6.089835859e-05 DT = 6.698819445e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.050043585e-05 MLMG: Initial residual (resid0) = 3.050043585e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 2.617769174e-15, 8.5827271e-11 MLMG: Timers: Solve = 0.048919507 Iter = 0.046443604 Bottom = 0.014771658 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.058937698e-05 MLMG: Initial residual (resid0) = 3.366932437e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 1.074457265e-15, 3.512517648e-11 MLMG: Timers: Solve = 0.04356922 Iter = 0.042041199 Bottom = 0.013633513 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003894011863 MLMG: Initial residual (resid0) = 0.003894011863 MLMG: Final Iter. 7 resid, resid/bnorm = 5.73434529e-16, 1.472606014e-13 MLMG: Timers: Solve = 0.408307771 Iter = 0.403098556 Bottom = 0.001272148 Done calling nodal solver Timestep 2 ends with TIME = 0.000127886553 DT = 6.698819445e-05 Timing summary: Advection :0.24216724 seconds MAC Proj :0.100225332 seconds Nodal Proj :0.432059038 seconds Reactions :0.009246199 seconds Misc :0.015751867 seconds Base State :0.013808651 seconds Time to advance time step: 0.79963437 Call to estdt for level 0 gives dt_lev = 0.3130343729 Minimum estdt over all levels = 0.3130343729 Call to estdt at beginning of step 3 gives dt =0.3130343729 dt_growth factor limits the new dt = 7.36870139e-05 Timestep 3 starts with TIME = 0.000127886553 DT = 7.36870139e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.95509247e-05 MLMG: Initial residual (resid0) = 3.95509247e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 3.72006714e-15, 9.40576527e-11 MLMG: Timers: Solve = 0.048750727 Iter = 0.046245967 Bottom = 0.014806142 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.959539493e-05 MLMG: Initial residual (resid0) = 1.25524138e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 9.441732267e-16, 2.384553124e-11 MLMG: Timers: Solve = 0.044584897 Iter = 0.043008331 Bottom = 0.014614612 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004283412997 MLMG: Initial residual (resid0) = 0.004283412997 MLMG: Final Iter. 7 resid, resid/bnorm = 6.205973235e-16, 1.4488384e-13 MLMG: Timers: Solve = 0.407696314 Iter = 0.400794848 Bottom = 0.00128878 Done calling nodal solver Timestep 3 ends with TIME = 0.0002015735669 DT = 7.36870139e-05 Timing summary: Advection :0.247276266 seconds MAC Proj :0.101233142 seconds Nodal Proj :0.432431247 seconds Reactions :0.009469571 seconds Misc :0.018744384 seconds Base State :0.02131805 seconds Time to advance time step: 0.809311325 Call to estdt for level 0 gives dt_lev = 0.3130323766 Minimum estdt over all levels = 0.3130323766 Call to estdt at beginning of step 4 gives dt =0.3130323766 dt_growth factor limits the new dt = 8.105571529e-05 Timestep 4 starts with TIME = 0.0002015735669 DT = 8.105571529e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.584764586e-05 MLMG: Initial residual (resid0) = 5.584764586e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 4.629172673e-15, 8.288930718e-11 MLMG: Timers: Solve = 0.052978013 Iter = 0.050456989 Bottom = 0.018924023 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.589656387e-05 MLMG: Initial residual (resid0) = 8.595300418e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 1.488443564e-15, 2.662853423e-11 MLMG: Timers: Solve = 0.044292467 Iter = 0.042737388 Bottom = 0.014384419 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004711754539 MLMG: Initial residual (resid0) = 0.004711754539 MLMG: Final Iter. 7 resid, resid/bnorm = 7.073334973e-16, 1.501210412e-13 MLMG: Timers: Solve = 0.414694869 Iter = 0.409340396 Bottom = 0.001483696 Done calling nodal solver Timestep 4 ends with TIME = 0.0002826292822 DT = 8.105571529e-05 Timing summary: Advection :0.264510956 seconds MAC Proj :0.105160848 seconds Nodal Proj :0.4422931 seconds Reactions :0.00938241 seconds Misc :0.018391755 seconds Base State :0.019325904 seconds Time to advance time step: 0.839900067 Call to estdt for level 0 gives dt_lev = 0.3130323437 Minimum estdt over all levels = 0.3130323437 Call to estdt at beginning of step 5 gives dt =0.3130323437 dt_growth factor limits the new dt = 8.916128682e-05 Timestep 5 starts with TIME = 0.0002826292822 DT = 8.916128682e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.377430079e-05 MLMG: Initial residual (resid0) = 7.377430079e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 5.790844982e-15, 7.849406799e-11 MLMG: Timers: Solve = 0.04871036 Iter = 0.046219571 Bottom = 0.014722836 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.382811063e-05 MLMG: Initial residual (resid0) = 1.227093904e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 2.001098397e-15, 2.710483013e-11 MLMG: Timers: Solve = 0.044272935 Iter = 0.042680571 Bottom = 0.014333738 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.005182930403 MLMG: Initial residual (resid0) = 0.005182930403 MLMG: Final Iter. 7 resid, resid/bnorm = 7.526531481e-16, 1.452176838e-13 MLMG: Timers: Solve = 0.407056369 Iter = 0.401045851 Bottom = 0.001253601 Done calling nodal solver Timestep 5 ends with TIME = 0.000371790569 DT = 8.916128682e-05 Timing summary: Advection :0.248413533 seconds MAC Proj :0.100641505 seconds Nodal Proj :0.433930756 seconds Reactions :0.009235486 seconds Misc :0.016384592 seconds Base State :0.01297074 seconds Time to advance time step: 0.808763532 Writing plotfile 5 Time to write plotfile: 0.061687044 Total Time: 5.483308755 Unused ParmParse Variables: [TOP]::maestro.v(nvals = 1) :: [1] [TOP]::amr.ref_ratio(nvals = 4) :: [2, 2, 2, 2] [TOP]::amr.check_file(nvals = 1) :: [RT_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] Total GPU global memory (MB): 12056 Free GPU global memory (MB): 11334 [The Arena] space allocated (MB): 9042 [The Arena] space used (MB): 0 [The Device Arena] space allocated (MB): 8 [The Device Arena] space used (MB): 0 [The Pinned Arena] space allocated (MB): 8 [The Pinned Arena] space used (MB): 0 AMReX (23.04-41-gcf6b46bd95a3) finalized