Initializing CUDA... CUDA initialized with 1 device. AMReX (23.07-25-g10b6cb26d0ac) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = cutoff densities: low density cutoff (for mapping the model) = 1e-10 buoyancy cutoff density (for zeroing rho - rho_0, centrifugal term) = 5e-10 anelastic cutoff = 1e-10 Maximum HSE Error = 4.547473509e-13 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile RT_pltInitData after InitData Time to write plotfile: 0.069444935 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.005013339 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile RT_pltafter_InitProj after InitProj Time to write plotfile: 0.066369395 Call to firstdt for level 0 gives dt_lev = 0.0006089835859 Multiplying dt_lev by init_shrink; dt_lev = 6.089835859e-05 Minimum firstdt over all levels = 6.089835859e-05 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.0054059 Iter = 0 Bottom = 0 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.08660444773 Minimum estdt over all levels = 0.08660444773 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.08660444773 Multiplying dt by init_shrink; dt = 0.008660444773 Ignoring this new dt since it's larger than the previous dt = 6.089835859e-05 Writing plotfile RT_pltafter_DivuIter after final DivuIter Time to write plotfile: 0.060865284 Doing initial pressure iteration #1 Timestep 0 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 0.002421164472 MLMG: Initial residual (resid0) = 0.002421164472 MLMG: Final Iter. 9 resid, resid/bnorm = 1.75190778e-13, 7.235806575e-11 MLMG: Timers: Solve = 0.048895513 Iter = 0.04739345 Bottom = 0.016311922 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 0.002421205691 MLMG: Initial residual (resid0) = 2.151449931e-06 MLMG: Final Iter. 7 resid, resid/bnorm = 9.927909819e-14, 4.100399175e-11 MLMG: Timers: Solve = 0.03578137 Iter = 0.034406787 Bottom = 0.011365601 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 58.12657035 MLMG: Initial residual (resid0) = 58.12657035 MLMG: Final Iter. 7 resid, resid/bnorm = 8.427036846e-12, 1.449773623e-13 MLMG: Timers: Solve = 0.406485882 Iter = 0.401065276 Bottom = 0.001036423 Done calling nodal solver Timestep 0 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.219081633 seconds MAC Proj :0.093746214 seconds Nodal Proj :0.428296258 seconds Reactions :0.011004618 seconds Misc :0.010797295 seconds Base State :0.010845317 seconds Time to advance time step: 0.763041674 Writing plotfile 0 after all initialization Time to write plotfile: 0.111702715 Calling Evolve() Timestep 1 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.394238647e-05 MLMG: Initial residual (resid0) = 2.394238647e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 3.184508457e-16, 1.330071445e-11 MLMG: Timers: Solve = 0.047530312 Iter = 0.045162085 Bottom = 0.01577791 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.394218844e-05 MLMG: Initial residual (resid0) = 1.928423239e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 6.036515824e-16, 2.521288244e-11 MLMG: Timers: Solve = 0.044505228 Iter = 0.043142541 Bottom = 0.01375351 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003539812449 MLMG: Initial residual (resid0) = 0.003539812449 MLMG: Final Iter. 7 resid, resid/bnorm = 5.243201706e-16, 1.481208901e-13 MLMG: Timers: Solve = 0.407572945 Iter = 0.401346335 Bottom = 0.001200201 Done calling nodal solver Timestep 1 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.228602531 seconds MAC Proj :0.100176257 seconds Nodal Proj :0.431648852 seconds Reactions :0.009967493 seconds Misc :0.01016378 seconds Base State :0.010873741 seconds Time to advance time step: 0.780708718 Call to estdt for level 0 gives dt_lev = 0.3128878797 Minimum estdt over all levels = 0.3128878797 Call to estdt at beginning of step 2 gives dt =0.3128878797 dt_growth factor limits the new dt = 6.698819445e-05 Timestep 2 starts with TIME = 6.089835859e-05 DT = 6.698819445e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.050043585e-05 MLMG: Initial residual (resid0) = 3.050043585e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 2.617769286e-15, 8.582727469e-11 MLMG: Timers: Solve = 0.050622022 Iter = 0.048286147 Bottom = 0.015481182 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.058937698e-05 MLMG: Initial residual (resid0) = 3.366932437e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 1.074458202e-15, 3.512520711e-11 MLMG: Timers: Solve = 0.044980665 Iter = 0.043625775 Bottom = 0.014231765 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003894011863 MLMG: Initial residual (resid0) = 0.003894011863 MLMG: Final Iter. 7 resid, resid/bnorm = 5.799397421e-16, 1.489311698e-13 MLMG: Timers: Solve = 0.402213679 Iter = 0.395979257 Bottom = 0.000999057 Done calling nodal solver Timestep 2 ends with TIME = 0.000127886553 DT = 6.698819445e-05 Timing summary: Advection :0.227242986 seconds MAC Proj :0.103831956 seconds Nodal Proj :0.426054898 seconds Reactions :0.009172216 seconds Misc :0.008727424 seconds Base State :0.012358056 seconds Time to advance time step: 0.77520672 Call to estdt for level 0 gives dt_lev = 0.3130343729 Minimum estdt over all levels = 0.3130343729 Call to estdt at beginning of step 3 gives dt =0.3130343729 dt_growth factor limits the new dt = 7.36870139e-05 Timestep 3 starts with TIME = 0.000127886553 DT = 7.36870139e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.955092471e-05 MLMG: Initial residual (resid0) = 3.955092471e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 3.720068437e-15, 9.405768549e-11 MLMG: Timers: Solve = 0.050452795 Iter = 0.048047223 Bottom = 0.015502708 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.959539493e-05 MLMG: Initial residual (resid0) = 1.25524138e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 9.441715327e-16, 2.384548845e-11 MLMG: Timers: Solve = 0.045961592 Iter = 0.044589572 Bottom = 0.015213661 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004283412997 MLMG: Initial residual (resid0) = 0.004283412997 MLMG: Final Iter. 7 resid, resid/bnorm = 6.568096761e-16, 1.533379285e-13 MLMG: Timers: Solve = 0.4094305 Iter = 0.40338014 Bottom = 0.001304481 Done calling nodal solver Timestep 3 ends with TIME = 0.0002015735669 DT = 7.36870139e-05 Timing summary: Advection :0.223828611 seconds MAC Proj :0.105195347 seconds Nodal Proj :0.433892856 seconds Reactions :0.009802635 seconds Misc :0.011156666 seconds Base State :0.013304151 seconds Time to advance time step: 0.784049617 Call to estdt for level 0 gives dt_lev = 0.3130323766 Minimum estdt over all levels = 0.3130323766 Call to estdt at beginning of step 4 gives dt =0.3130323766 dt_growth factor limits the new dt = 8.105571529e-05 Timestep 4 starts with TIME = 0.0002015735669 DT = 8.105571529e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.584764586e-05 MLMG: Initial residual (resid0) = 5.584764586e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 4.629171906e-15, 8.288929343e-11 MLMG: Timers: Solve = 0.050014234 Iter = 0.048049112 Bottom = 0.015530804 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.589656387e-05 MLMG: Initial residual (resid0) = 8.595300418e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 1.48844187e-15, 2.662850392e-11 MLMG: Timers: Solve = 0.045856602 Iter = 0.044491021 Bottom = 0.014993552 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004711754539 MLMG: Initial residual (resid0) = 0.004711754539 MLMG: Final Iter. 7 resid, resid/bnorm = 7.05165093e-16, 1.496608295e-13 MLMG: Timers: Solve = 0.412513947 Iter = 0.406449307 Bottom = 0.001204612 Done calling nodal solver Timestep 4 ends with TIME = 0.0002826292822 DT = 8.105571529e-05 Timing summary: Advection :0.241443186 seconds MAC Proj :0.10380689 seconds Nodal Proj :0.435171085 seconds Reactions :0.00956817 seconds Misc :0.009267973 seconds Base State :0.014829725 seconds Time to advance time step: 0.799426861 Call to estdt for level 0 gives dt_lev = 0.3130323437 Minimum estdt over all levels = 0.3130323437 Call to estdt at beginning of step 5 gives dt =0.3130323437 dt_growth factor limits the new dt = 8.916128682e-05 Timestep 5 starts with TIME = 0.0002826292822 DT = 8.916128682e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.377430079e-05 MLMG: Initial residual (resid0) = 7.377430079e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 5.790845194e-15, 7.849407086e-11 MLMG: Timers: Solve = 0.050307774 Iter = 0.047969095 Bottom = 0.015370509 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.382811063e-05 MLMG: Initial residual (resid0) = 1.227093904e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 2.001096703e-15, 2.710480718e-11 MLMG: Timers: Solve = 0.045784183 Iter = 0.044388291 Bottom = 0.015015254 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.005182930403 MLMG: Initial residual (resid0) = 0.005182930403 MLMG: Final Iter. 7 resid, resid/bnorm = 7.476658181e-16, 1.442554231e-13 MLMG: Timers: Solve = 0.40681854 Iter = 0.401116447 Bottom = 0.001008682 Done calling nodal solver Timestep 5 ends with TIME = 0.000371790569 DT = 8.916128682e-05 Timing summary: Advection :0.229155636 seconds MAC Proj :0.104148478 seconds Nodal Proj :0.430073538 seconds Reactions :0.009753934 seconds Misc :0.010908469 seconds Base State :0.010879941 seconds Time to advance time step: 0.784211817 Writing plotfile 5 Time to write plotfile: 0.063961261 Total Time: 5.175772613 Unused ParmParse Variables: [TOP]::maestro.v(nvals = 1) :: [1] [TOP]::amr.ref_ratio(nvals = 4) :: [2, 2, 2, 2] [TOP]::amr.check_file(nvals = 1) :: [RT_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] Total GPU global memory (MB): 12056 Free GPU global memory (MB): 11334 [The Arena] space allocated (MB): 9042 [The Arena] space used (MB): 0 [The Device Arena] space allocated (MB): 8 [The Device Arena] space used (MB): 0 [The Pinned Arena] space allocated (MB): 8 [The Pinned Arena] space used (MB): 0 AMReX (23.07-25-g10b6cb26d0ac) finalized