Initializing AMReX (24.06-26-g7418556773c7)... Initializing CUDA... CUDA initialized with 1 device. AMReX (24.06-26-g7418556773c7) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = cutoff densities: low density cutoff (for mapping the model) = 1e-10 buoyancy cutoff density (for zeroing rho - rho_0, centrifugal term) = 5e-10 anelastic cutoff = 1e-10 Maximum HSE Error = 2.273736754e-13 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile RT_pltInitData after InitData Time to write plotfile: 0.065815125 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.005840031 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile RT_pltafter_InitProj after InitProj Time to write plotfile: 0.059907739 Call to firstdt for level 0 gives dt_lev = 0.0006089835859 Multiplying dt_lev by init_shrink; dt_lev = 6.089835859e-05 Minimum firstdt over all levels = 6.089835859e-05 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.005978821 Iter = 0 Bottom = 0 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.08660444773 Minimum estdt over all levels = 0.08660444773 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.08660444773 Multiplying dt by init_shrink; dt = 0.008660444773 Ignoring this new dt since it's larger than the previous dt = 6.089835859e-05 Writing plotfile RT_pltafter_DivuIter after final DivuIter Time to write plotfile: 0.053723726 Doing initial pressure iteration #1  Timestep 0 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 0.002421164472 MLMG: Initial residual (resid0) = 0.002421164472 MLMG: Final Iter. 9 resid, resid/bnorm = 1.751907732e-13, 7.235806376e-11 MLMG: Timers: Solve = 0.059265275 Iter = 0.057296327 Bottom = 0.023748168 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 0.002421205691 MLMG: Initial residual (resid0) = 2.151449931e-06 MLMG: Final Iter. 7 resid, resid/bnorm = 9.927908594e-14, 4.100398669e-11 MLMG: Timers: Solve = 0.039126643 Iter = 0.037667002 Bottom = 0.011926369 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 58.12657035 MLMG: Initial residual (resid0) = 58.12657035 MLMG: Final Iter. 7 resid, resid/bnorm = 8.768097359e-12, 1.508449115e-13 MLMG: Timers: Solve = 0.437609032 Iter = 0.43157598 Bottom = 0.001533491 Done calling nodal solver Timestep 0 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.212252783 seconds MAC Proj :0.111497535 seconds Nodal Proj :0.461405816 seconds Reactions :0.01304293 seconds Misc :0.011235328 seconds Base State :0.01347355 seconds Time to advance time step: 0.809583482 Writing plotfile 0 after all initialization Time to write plotfile: 0.098422505 Beginning main evolution  Timestep 1 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.394238647e-05 MLMG: Initial residual (resid0) = 2.394238647e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 3.184674765e-16, 1.330140907e-11 MLMG: Timers: Solve = 0.052066233 Iter = 0.049548569 Bottom = 0.016828625 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.394218844e-05 MLMG: Initial residual (resid0) = 1.928423212e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 6.036515824e-16, 2.521288244e-11 MLMG: Timers: Solve = 0.048940162 Iter = 0.047525693 Bottom = 0.014730845 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003539812449 MLMG: Initial residual (resid0) = 0.003539812449 MLMG: Final Iter. 7 resid, resid/bnorm = 5.307169634e-16, 1.499279894e-13 MLMG: Timers: Solve = 0.437472685 Iter = 0.43097792 Bottom = 0.001560923 Done calling nodal solver Timestep 1 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.206425536 seconds MAC Proj :0.110333272 seconds Nodal Proj :0.462594637 seconds Reactions :0.011513342 seconds Misc :0.009878779 seconds Base State :0.013414212 seconds Time to advance time step: 0.800898207 Call to estdt for level 0 gives dt_lev = 0.3128878797 Minimum estdt over all levels = 0.3128878797 Call to estdt at beginning of step 2 gives dt =0.3128878797 dt_growth factor limits the new dt = 6.698819445e-05  Timestep 2 starts with TIME = 6.089835859e-05 DT = 6.698819445e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.050043585e-05 MLMG: Initial residual (resid0) = 3.050043585e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 2.284814624e-15, 7.491088439e-11 MLMG: Timers: Solve = 0.051146775 Iter = 0.049061415 Bottom = 0.016246471 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.059063412e-05 MLMG: Initial residual (resid0) = 5.66083759e-06 MLMG: Final Iter. 10 resid, resid/bnorm = 4.89262324e-16, 1.599386015e-11 MLMG: Timers: Solve = 0.054471144 Iter = 0.05305593 Bottom = 0.016631311 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003894013591 MLMG: Initial residual (resid0) = 0.003894013591 MLMG: Final Iter. 7 resid, resid/bnorm = 5.726755875e-16, 1.470656366e-13 MLMG: Timers: Solve = 0.436118192 Iter = 0.430247749 Bottom = 0.001718417 Done calling nodal solver Timestep 2 ends with TIME = 0.000127886553 DT = 6.698819445e-05 Timing summary: Advection :0.211016154 seconds MAC Proj :0.115366665 seconds Nodal Proj :0.460773039 seconds Reactions :0.011105481 seconds Misc :0.012460278 seconds Base State :0.0163144 seconds Time to advance time step: 0.81089669 Call to estdt for level 0 gives dt_lev = 0.3130286362 Minimum estdt over all levels = 0.3130286362 Call to estdt at beginning of step 3 gives dt =0.3130286362 dt_growth factor limits the new dt = 7.36870139e-05  Timestep 3 starts with TIME = 0.000127886553 DT = 7.36870139e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.168800511e-05 MLMG: Initial residual (resid0) = 3.168800511e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 5.650713492e-16, 1.783234215e-11 MLMG: Timers: Solve = 0.056363876 Iter = 0.053816581 Bottom = 0.017417238 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.178722337e-05 MLMG: Initial residual (resid0) = 1.012935749e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 6.833624649e-16, 2.149802318e-11 MLMG: Timers: Solve = 0.054333097 Iter = 0.052910154 Bottom = 0.01658993 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004283414244 MLMG: Initial residual (resid0) = 0.004283414244 MLMG: Final Iter. 7 resid, resid/bnorm = 6.409803244e-16, 1.496423852e-13 MLMG: Timers: Solve = 0.435481707 Iter = 0.428624044 Bottom = 0.001625341 Done calling nodal solver Timestep 3 ends with TIME = 0.0002015735669 DT = 7.36870139e-05 Timing summary: Advection :0.204060124 seconds MAC Proj :0.120609396 seconds Nodal Proj :0.460532827 seconds Reactions :0.010924579 seconds Misc :0.01063466 seconds Base State :0.014681709 seconds Time to advance time step: 0.806938333 Call to estdt for level 0 gives dt_lev = 0.3130285358 Minimum estdt over all levels = 0.3130285358 Call to estdt at beginning of step 4 gives dt =0.3130285358 dt_growth factor limits the new dt = 8.105571529e-05  Timestep 4 starts with TIME = 0.0002015735669 DT = 8.105571529e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.570538736e-05 MLMG: Initial residual (resid0) = 3.570538736e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 7.571110825e-16, 2.120439347e-11 MLMG: Timers: Solve = 0.055775579 Iter = 0.053686487 Bottom = 0.017418134 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.581452755e-05 MLMG: Initial residual (resid0) = 1.504387741e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 8.870154435e-16, 2.476691734e-11 MLMG: Timers: Solve = 0.054259941 Iter = 0.052832328 Bottom = 0.016583298 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004711755906 MLMG: Initial residual (resid0) = 0.004711755906 MLMG: Final Iter. 7 resid, resid/bnorm = 6.949735926e-16, 1.47497792e-13 MLMG: Timers: Solve = 0.436192004 Iter = 0.430076937 Bottom = 0.001578888 Done calling nodal solver Timestep 4 ends with TIME = 0.0002826292822 DT = 8.105571529e-05 Timing summary: Advection :0.217178912 seconds MAC Proj :0.119777122 seconds Nodal Proj :0.458604511 seconds Reactions :0.011878205 seconds Misc :0.011604904 seconds Base State :0.019178576 seconds Time to advance time step: 0.819216032 Call to estdt for level 0 gives dt_lev = 0.313028505 Minimum estdt over all levels = 0.313028505 Call to estdt at beginning of step 5 gives dt =0.313028505 dt_growth factor limits the new dt = 8.916128682e-05  Timestep 5 starts with TIME = 0.0002826292822 DT = 8.916128682e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.013180326e-05 MLMG: Initial residual (resid0) = 4.013180326e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 9.68140024e-16, 2.412401002e-11 MLMG: Timers: Solve = 0.055631608 Iter = 0.053572424 Bottom = 0.017243296 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.025185748e-05 MLMG: Initial residual (resid0) = 2.044985444e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 1.111036176e-15, 2.760210946e-11 MLMG: Timers: Solve = 0.054386299 Iter = 0.05297398 Bottom = 0.016622778 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.005182931901 MLMG: Initial residual (resid0) = 0.005182931901 MLMG: Final Iter. 7 resid, resid/bnorm = 7.806255642e-16, 1.506146673e-13 MLMG: Timers: Solve = 0.429562747 Iter = 0.42319639 Bottom = 0.001593327 Done calling nodal solver Timestep 5 ends with TIME = 0.000371790569 DT = 8.916128682e-05 Timing summary: Advection :0.207941805 seconds MAC Proj :0.119519888 seconds Nodal Proj :0.456439163 seconds Reactions :0.011483422 seconds Misc :0.009735401 seconds Base State :0.015427061 seconds Time to advance time step: 0.805293632 Writing plotfile 5 Time to write plotfile: 0.055871566 Total Time: 5.340487183 Unused ParmParse Variables: [TOP]::amr.ref_ratio(nvals = 4) :: [2, 2, 2, 2] [TOP]::amr.check_file(nvals = 1) :: [RT_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] Total GPU global memory (MB): 12049 Free GPU global memory (MB): 11333 [The Arena] space allocated (MB): 9037 [The Arena] space used (MB): 0 [The Device Arena] space allocated (MB): 8 [The Device Arena] space used (MB): 0 [The Pinned Arena] space allocated (MB): 8 [The Pinned Arena] space used (MB): 0 AMReX (24.06-26-g7418556773c7) finalized