Initializing AMReX (24.09-6-gde4dc974dda7)... Initializing CUDA... CUDA initialized with 1 device. AMReX (24.09-6-gde4dc974dda7) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = cutoff densities: low density cutoff (for mapping the model) = 1e-10 buoyancy cutoff density (for zeroing rho - rho_0, centrifugal term) = 5e-10 anelastic cutoff = 1e-10 Maximum HSE Error = 2.273736754e-13 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile RT_pltInitData after InitData Time to write plotfile: 0.063602563 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.00556432 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile RT_pltafter_InitProj after InitProj Time to write plotfile: 0.056491067 Call to firstdt for level 0 gives dt_lev = 0.0006089835859 Multiplying dt_lev by init_shrink; dt_lev = 6.089835859e-05 Minimum firstdt over all levels = 6.089835859e-05 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.005829605 Iter = 0 Bottom = 0 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.08660444773 Minimum estdt over all levels = 0.08660444773 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.08660444773 Multiplying dt by init_shrink; dt = 0.008660444773 Ignoring this new dt since it's larger than the previous dt = 6.089835859e-05 Writing plotfile RT_pltafter_DivuIter after final DivuIter Time to write plotfile: 0.089643612 Doing initial pressure iteration #1  Timestep 0 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 0.002421164472 MLMG: Initial residual (resid0) = 0.002421164472 MLMG: Final Iter. 9 resid, resid/bnorm = 1.751907817e-13, 7.235806729e-11 MLMG: Timers: Solve = 0.048388939 Iter = 0.046514676 Bottom = 0.015276729 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 0.002421205691 MLMG: Initial residual (resid0) = 2.151449931e-06 MLMG: Final Iter. 7 resid, resid/bnorm = 9.927909427e-14, 4.100399014e-11 MLMG: Timers: Solve = 0.039354852 Iter = 0.037872699 Bottom = 0.011753205 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 58.12657035 MLMG: Initial residual (resid0) = 58.12657035 MLMG: Final Iter. 7 resid, resid/bnorm = 8.768097359e-12, 1.508449115e-13 MLMG: Timers: Solve = 0.433889005 Iter = 0.427624483 Bottom = 0.001786461 Done calling nodal solver Timestep 0 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.224626281 seconds MAC Proj :0.098439227 seconds Nodal Proj :0.457983705 seconds Reactions :0.013574913 seconds Misc :0.011455813 seconds Base State :0.012743627 seconds Time to advance time step: 0.806472452 Writing plotfile 0 after all initialization Time to write plotfile: 0.053025221 Beginning main evolution  Timestep 1 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.394238647e-05 MLMG: Initial residual (resid0) = 2.394238647e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 3.182689466e-16, 1.329311708e-11 MLMG: Timers: Solve = 0.0484906 Iter = 0.046111475 Bottom = 0.015519759 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.394218844e-05 MLMG: Initial residual (resid0) = 1.92842345e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 6.036515824e-16, 2.521288244e-11 MLMG: Timers: Solve = 0.045433332 Iter = 0.044105658 Bottom = 0.01344848 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003539812449 MLMG: Initial residual (resid0) = 0.003539812449 MLMG: Final Iter. 7 resid, resid/bnorm = 5.222601865e-16, 1.475389428e-13 MLMG: Timers: Solve = 0.433059445 Iter = 0.427059889 Bottom = 0.002325839 Done calling nodal solver Timestep 1 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.200452234 seconds MAC Proj :0.102182963 seconds Nodal Proj :0.458868384 seconds Reactions :0.01146876 seconds Misc :0.010082466 seconds Base State :0.011617853 seconds Time to advance time step: 0.783238912 Call to estdt for level 0 gives dt_lev = 0.3128878797 Minimum estdt over all levels = 0.3128878797 Call to estdt at beginning of step 2 gives dt =0.3128878797 dt_growth factor limits the new dt = 6.698819445e-05  Timestep 2 starts with TIME = 6.089835859e-05 DT = 6.698819445e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.050043585e-05 MLMG: Initial residual (resid0) = 3.050043585e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 2.284815048e-15, 7.491089827e-11 MLMG: Timers: Solve = 0.047496845 Iter = 0.045540767 Bottom = 0.014861186 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.059063412e-05 MLMG: Initial residual (resid0) = 5.66083759e-06 MLMG: Final Iter. 10 resid, resid/bnorm = 4.892619004e-16, 1.59938463e-11 MLMG: Timers: Solve = 0.050556905 Iter = 0.049233509 Bottom = 0.015265922 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003894013591 MLMG: Initial residual (resid0) = 0.003894013591 MLMG: Final Iter. 7 resid, resid/bnorm = 5.689893001e-16, 1.461189816e-13 MLMG: Timers: Solve = 0.434881534 Iter = 0.429286818 Bottom = 0.008327482 Done calling nodal solver Timestep 2 ends with TIME = 0.000127886553 DT = 6.698819445e-05 Timing summary: Advection :0.198525701 seconds MAC Proj :0.106204805 seconds Nodal Proj :0.457473502 seconds Reactions :0.011610178 seconds Misc :0.009867807 seconds Base State :0.012502357 seconds Time to advance time step: 0.783890824 Call to estdt for level 0 gives dt_lev = 0.3130286362 Minimum estdt over all levels = 0.3130286362 Call to estdt at beginning of step 3 gives dt =0.3130286362 dt_growth factor limits the new dt = 7.36870139e-05  Timestep 3 starts with TIME = 0.000127886553 DT = 7.36870139e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.168800511e-05 MLMG: Initial residual (resid0) = 3.168800511e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 5.650705022e-16, 1.783231542e-11 MLMG: Timers: Solve = 0.052100249 Iter = 0.050112002 Bottom = 0.016067679 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.178722337e-05 MLMG: Initial residual (resid0) = 1.012935749e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 6.833624649e-16, 2.149802318e-11 MLMG: Timers: Solve = 0.050714981 Iter = 0.049356577 Bottom = 0.015201468 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004283414244 MLMG: Initial residual (resid0) = 0.004283414244 MLMG: Final Iter. 7 resid, resid/bnorm = 6.47268697e-16, 1.5111046e-13 MLMG: Timers: Solve = 0.425526128 Iter = 0.419599134 Bottom = 0.001892566 Done calling nodal solver Timestep 3 ends with TIME = 0.0002015735669 DT = 7.36870139e-05 Timing summary: Advection :0.204575421 seconds MAC Proj :0.111424803 seconds Nodal Proj :0.451974478 seconds Reactions :0.010973418 seconds Misc :0.011720909 seconds Base State :0.014944361 seconds Time to advance time step: 0.790859634 Call to estdt for level 0 gives dt_lev = 0.3130285358 Minimum estdt over all levels = 0.3130285358 Call to estdt at beginning of step 4 gives dt =0.3130285358 dt_growth factor limits the new dt = 8.105571529e-05  Timestep 4 starts with TIME = 0.0002015735669 DT = 8.105571529e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.570538736e-05 MLMG: Initial residual (resid0) = 3.570538736e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 7.571093885e-16, 2.120434602e-11 MLMG: Timers: Solve = 0.051968546 Iter = 0.050006547 Bottom = 0.016020409 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.581452755e-05 MLMG: Initial residual (resid0) = 1.504387741e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 8.870120553e-16, 2.476682274e-11 MLMG: Timers: Solve = 0.050579187 Iter = 0.049247903 Bottom = 0.015213038 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004711755906 MLMG: Initial residual (resid0) = 0.004711755906 MLMG: Final Iter. 7 resid, resid/bnorm = 7.097187421e-16, 1.506272303e-13 MLMG: Timers: Solve = 0.428157597 Iter = 0.422451464 Bottom = 0.002234621 Done calling nodal solver Timestep 4 ends with TIME = 0.0002826292822 DT = 8.105571529e-05 Timing summary: Advection :0.202848814 seconds MAC Proj :0.110865504 seconds Nodal Proj :0.451059064 seconds Reactions :0.011540746 seconds Misc :0.009775065 seconds Base State :0.010792313 seconds Time to advance time step: 0.786284597 Call to estdt for level 0 gives dt_lev = 0.313028505 Minimum estdt over all levels = 0.313028505 Call to estdt at beginning of step 5 gives dt =0.313028505 dt_growth factor limits the new dt = 8.916128682e-05  Timestep 5 starts with TIME = 0.0002826292822 DT = 8.916128682e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.013180326e-05 MLMG: Initial residual (resid0) = 4.013180326e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 9.68140871e-16, 2.412403113e-11 MLMG: Timers: Solve = 0.052274416 Iter = 0.049892076 Bottom = 0.015843069 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.025185748e-05 MLMG: Initial residual (resid0) = 2.044985444e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 1.111036176e-15, 2.760210946e-11 MLMG: Timers: Solve = 0.050605361 Iter = 0.04926903 Bottom = 0.015185312 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.005182931901 MLMG: Initial residual (resid0) = 0.005182931901 MLMG: Final Iter. 7 resid, resid/bnorm = 7.51568946e-16, 1.450084547e-13 MLMG: Timers: Solve = 0.426876914 Iter = 0.419940574 Bottom = 0.002085491 Done calling nodal solver Timestep 5 ends with TIME = 0.000371790569 DT = 8.916128682e-05 Timing summary: Advection :0.210131824 seconds MAC Proj :0.111164809 seconds Nodal Proj :0.452772468 seconds Reactions :0.010989425 seconds Misc :0.012737725 seconds Base State :0.015383187 seconds Time to advance time step: 0.797997958 Writing plotfile 5 Time to write plotfile: 0.0527449 Total Time: 5.212402197 Unused ParmParse Variables: [TOP]::amr.check_file(nvals = 1) :: [RT_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] [TOP]::amr.ref_ratio(nvals = 4) :: [2, 2, 2, 2] Total GPU global memory (MB): 12049 Free GPU global memory (MB): 11410 [The Arena] space allocated (MB): 9037 [The Arena] space used (MB): 0 [The Device Arena] space allocated (MB): 8 [The Device Arena] space used (MB): 0 [The Pinned Arena] space allocated (MB): 8 [The Pinned Arena] space used (MB): 0 AMReX (24.09-6-gde4dc974dda7) finalized