Initializing AMReX (24.09-27-g028638564f7b)... Initializing CUDA... CUDA initialized with 1 device. AMReX (24.09-27-g028638564f7b) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = cutoff densities: low density cutoff (for mapping the model) = 1e-10 buoyancy cutoff density (for zeroing rho - rho_0, centrifugal term) = 5e-10 anelastic cutoff = 1e-10 Maximum HSE Error = 2.273736754e-13 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile RT_pltInitData after InitData Time to write plotfile: 0.064831562 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.005440454 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile RT_pltafter_InitProj after InitProj Time to write plotfile: 0.057010335 Call to firstdt for level 0 gives dt_lev = 0.0006089835859 Multiplying dt_lev by init_shrink; dt_lev = 6.089835859e-05 Minimum firstdt over all levels = 6.089835859e-05 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.005642494 Iter = 0 Bottom = 0 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.08660444773 Minimum estdt over all levels = 0.08660444773 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.08660444773 Multiplying dt by init_shrink; dt = 0.008660444773 Ignoring this new dt since it's larger than the previous dt = 6.089835859e-05 Writing plotfile RT_pltafter_DivuIter after final DivuIter Time to write plotfile: 0.051961443 Doing initial pressure iteration #1  Timestep 0 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 0.002421164472 MLMG: Initial residual (resid0) = 0.002421164472 MLMG: Final Iter. 9 resid, resid/bnorm = 1.751907823e-13, 7.235806752e-11 MLMG: Timers: Solve = 0.048965186 Iter = 0.047085776 Bottom = 0.015472206 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 0.002421205691 MLMG: Initial residual (resid0) = 2.151449931e-06 MLMG: Final Iter. 7 resid, resid/bnorm = 9.927908967e-14, 4.100398823e-11 MLMG: Timers: Solve = 0.036428899 Iter = 0.035048251 Bottom = 0.010981264 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 58.12657035 MLMG: Initial residual (resid0) = 58.12657035 MLMG: Final Iter. 7 resid, resid/bnorm = 8.895995052e-12, 1.530452425e-13 MLMG: Timers: Solve = 0.427461285 Iter = 0.421711523 Bottom = 0.001930903 Done calling nodal solver Timestep 0 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.21264213 seconds MAC Proj :0.095572932 seconds Nodal Proj :0.450444827 seconds Reactions :0.013202645 seconds Misc :0.01239839 seconds Base State :0.013281327 seconds Time to advance time step: 0.784457259 Writing plotfile 0 after all initialization Time to write plotfile: 0.053597658 Beginning main evolution  Timestep 1 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.394238647e-05 MLMG: Initial residual (resid0) = 2.394238647e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 3.185134465e-16, 1.330332909e-11 MLMG: Timers: Solve = 0.048044762 Iter = 0.046054144 Bottom = 0.015532831 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.394218844e-05 MLMG: Initial residual (resid0) = 1.928423149e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 6.036515824e-16, 2.521288244e-11 MLMG: Timers: Solve = 0.045270046 Iter = 0.043946827 Bottom = 0.013369964 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003539812449 MLMG: Initial residual (resid0) = 0.003539812449 MLMG: Final Iter. 7 resid, resid/bnorm = 5.128276276e-16, 1.44874237e-13 MLMG: Timers: Solve = 0.431481659 Iter = 0.425447523 Bottom = 0.001951433 Done calling nodal solver Timestep 1 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.19878677 seconds MAC Proj :0.10149612 seconds Nodal Proj :0.457057683 seconds Reactions :0.011506562 seconds Misc :0.01111411 seconds Base State :0.012458798 seconds Time to advance time step: 0.780137724 Call to estdt for level 0 gives dt_lev = 0.3128878797 Minimum estdt over all levels = 0.3128878797 Call to estdt at beginning of step 2 gives dt =0.3128878797 dt_growth factor limits the new dt = 6.698819445e-05  Timestep 2 starts with TIME = 6.089835859e-05 DT = 6.698819445e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.050043585e-05 MLMG: Initial residual (resid0) = 3.050043585e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 2.284814624e-15, 7.491088439e-11 MLMG: Timers: Solve = 0.047241049 Iter = 0.045292363 Bottom = 0.014825028 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.059063412e-05 MLMG: Initial residual (resid0) = 5.66083759e-06 MLMG: Final Iter. 10 resid, resid/bnorm = 4.892627475e-16, 1.599387399e-11 MLMG: Timers: Solve = 0.050389951 Iter = 0.049074623 Bottom = 0.015196915 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003894013591 MLMG: Initial residual (resid0) = 0.003894013591 MLMG: Final Iter. 7 resid, resid/bnorm = 5.649777521e-16, 1.450887982e-13 MLMG: Timers: Solve = 0.430118858 Iter = 0.424306581 Bottom = 0.00169797 Done calling nodal solver Timestep 2 ends with TIME = 0.000127886553 DT = 6.698819445e-05 Timing summary: Advection :0.199697039 seconds MAC Proj :0.10568817 seconds Nodal Proj :0.453333318 seconds Reactions :0.011747686 seconds Misc :0.009747178 seconds Base State :0.011810392 seconds Time to advance time step: 0.780415944 Call to estdt for level 0 gives dt_lev = 0.3130286362 Minimum estdt over all levels = 0.3130286362 Call to estdt at beginning of step 3 gives dt =0.3130286362 dt_growth factor limits the new dt = 7.36870139e-05  Timestep 3 starts with TIME = 0.000127886553 DT = 7.36870139e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.168800511e-05 MLMG: Initial residual (resid0) = 3.168800511e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 5.650713492e-16, 1.783234215e-11 MLMG: Timers: Solve = 0.051663521 Iter = 0.049741934 Bottom = 0.015885552 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.178722337e-05 MLMG: Initial residual (resid0) = 1.012935749e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 6.83363312e-16, 2.149804983e-11 MLMG: Timers: Solve = 0.050622718 Iter = 0.049271269 Bottom = 0.015277428 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004283414244 MLMG: Initial residual (resid0) = 0.004283414244 MLMG: Final Iter. 7 resid, resid/bnorm = 6.398961222e-16, 1.493892689e-13 MLMG: Timers: Solve = 0.427933228 Iter = 0.421327679 Bottom = 0.001946203 Done calling nodal solver Timestep 3 ends with TIME = 0.0002015735669 DT = 7.36870139e-05 Timing summary: Advection :0.204414368 seconds MAC Proj :0.110415446 seconds Nodal Proj :0.453668225 seconds Reactions :0.011200837 seconds Misc :0.01148339 seconds Base State :0.013331398 seconds Time to advance time step: 0.791352384 Call to estdt for level 0 gives dt_lev = 0.3130285358 Minimum estdt over all levels = 0.3130285358 Call to estdt at beginning of step 4 gives dt =0.3130285358 dt_growth factor limits the new dt = 8.105571529e-05  Timestep 4 starts with TIME = 0.0002015735669 DT = 8.105571529e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.570538736e-05 MLMG: Initial residual (resid0) = 3.570538736e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 7.571093885e-16, 2.120434602e-11 MLMG: Timers: Solve = 0.052317279 Iter = 0.049917635 Bottom = 0.01598678 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.581452755e-05 MLMG: Initial residual (resid0) = 1.504387741e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 8.870120553e-16, 2.476682274e-11 MLMG: Timers: Solve = 0.050336607 Iter = 0.049019933 Bottom = 0.015170819 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004711755906 MLMG: Initial residual (resid0) = 0.004711755906 MLMG: Final Iter. 7 resid, resid/bnorm = 7.305354238e-16, 1.550452609e-13 MLMG: Timers: Solve = 0.425937177 Iter = 0.420203706 Bottom = 0.001864696 Done calling nodal solver Timestep 4 ends with TIME = 0.0002826292822 DT = 8.105571529e-05 Timing summary: Advection :0.196789492 seconds MAC Proj :0.110810828 seconds Nodal Proj :0.448142202 seconds Reactions :0.011709082 seconds Misc :0.009863555 seconds Base State :0.011320611 seconds Time to advance time step: 0.777513946 Call to estdt for level 0 gives dt_lev = 0.313028505 Minimum estdt over all levels = 0.313028505 Call to estdt at beginning of step 5 gives dt =0.313028505 dt_growth factor limits the new dt = 8.916128682e-05  Timestep 5 starts with TIME = 0.0002826292822 DT = 8.916128682e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.013180326e-05 MLMG: Initial residual (resid0) = 4.013180326e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 9.681425651e-16, 2.412407334e-11 MLMG: Timers: Solve = 0.05164974 Iter = 0.049682578 Bottom = 0.015763953 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.025185748e-05 MLMG: Initial residual (resid0) = 2.044985444e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 1.111036176e-15, 2.760210946e-11 MLMG: Timers: Solve = 0.050422595 Iter = 0.04909953 Bottom = 0.015183901 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.005182931901 MLMG: Initial residual (resid0) = 0.005182931901 MLMG: Final Iter. 7 resid, resid/bnorm = 7.708677446e-16, 1.48731984e-13 MLMG: Timers: Solve = 0.426911116 Iter = 0.420730792 Bottom = 0.002010991 Done calling nodal solver Timestep 5 ends with TIME = 0.000371790569 DT = 8.916128682e-05 Timing summary: Advection :0.197678731 seconds MAC Proj :0.110272318 seconds Nodal Proj :0.453685968 seconds Reactions :0.010923728 seconds Misc :0.012858631 seconds Base State :0.015294483 seconds Time to advance time step: 0.785644296 Writing plotfile 5 Time to write plotfile: 0.052486523 Total Time: 5.125204805 Unused ParmParse Variables: [TOP]::amr.check_file(nvals = 1) :: [RT_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] [TOP]::amr.ref_ratio(nvals = 4) :: [2, 2, 2, 2] Total GPU global memory (MB): 12049 Free GPU global memory (MB): 11400 [The Arena] space allocated (MB): 9037 [The Arena] space used (MB): 0 [The Device Arena] space allocated (MB): 8 [The Device Arena] space used (MB): 0 [The Pinned Arena] space allocated (MB): 8 [The Pinned Arena] space used (MB): 0 AMReX (24.09-27-g028638564f7b) finalized