Initializing AMReX (25.02-5-g78bdf0faabc4)... Initializing CUDA... CUDA initialized with 1 device. AMReX (25.02-5-g78bdf0faabc4) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = cutoff densities: low density cutoff (for mapping the model) = 1e-10 buoyancy cutoff density (for zeroing rho - rho_0, centrifugal term) = 5e-10 anelastic cutoff = 1e-10 Maximum HSE Error = 2.273736754e-13 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile RT_pltInitData after InitData Time to write plotfile: 0.062713625 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.00797322 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile RT_pltafter_InitProj after InitProj Time to write plotfile: 0.064169586 Call to firstdt for level 0 gives dt_lev = 0.0006089835859 Multiplying dt_lev by init_shrink; dt_lev = 6.089835859e-05 Minimum firstdt over all levels = 6.089835859e-05 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.007230953 Iter = 0 Bottom = 0 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.08660444773 Minimum estdt over all levels = 0.08660444773 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.08660444773 Multiplying dt by init_shrink; dt = 0.008660444773 Ignoring this new dt since it's larger than the previous dt = 6.089835859e-05 Writing plotfile RT_pltafter_DivuIter after final DivuIter Time to write plotfile: 0.051707597 Doing initial pressure iteration #1  Timestep 0 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 0.002421164472 MLMG: Initial residual (resid0) = 0.002421164472 MLMG: Final Iter. 9 resid, resid/bnorm = 1.751907897e-13, 7.235807057e-11 MLMG: Timers: Solve = 0.053358492 Iter = 0.051183794 Bottom = 0.016274004 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 0.002421205691 MLMG: Initial residual (resid0) = 2.151449931e-06 MLMG: Final Iter. 7 resid, resid/bnorm = 9.927909443e-14, 4.10039902e-11 MLMG: Timers: Solve = 0.038100483 Iter = 0.036658902 Bottom = 0.010964183 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 58.12657035 MLMG: Initial residual (resid0) = 58.12657035 MLMG: Final Iter. 7 resid, resid/bnorm = 8.789413641e-12, 1.512116333e-13 MLMG: Timers: Solve = 0.443802062 Iter = 0.436285513 Bottom = 0.003667422 Done calling nodal solver Timestep 0 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.196065071 seconds MAC Proj :0.102288366 seconds Nodal Proj :0.466620081 seconds Reactions :0.01053574 seconds Misc :0.009651482 seconds Base State :0.010891511 seconds Time to advance time step: 0.785298326 Writing plotfile 0 after all initialization Time to write plotfile: 0.053747381 Beginning main evolution  Timestep 1 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.394238647e-05 MLMG: Initial residual (resid0) = 2.394238647e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 3.182739967e-16, 1.329332801e-11 MLMG: Timers: Solve = 0.048615757 Iter = 0.046052539 Bottom = 0.014806655 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.394218844e-05 MLMG: Initial residual (resid0) = 1.928423433e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 6.036515824e-16, 2.521288244e-11 MLMG: Timers: Solve = 0.045673112 Iter = 0.04432143 Bottom = 0.01298892 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003539812449 MLMG: Initial residual (resid0) = 0.003539812449 MLMG: Final Iter. 7 resid, resid/bnorm = 5.312590645e-16, 1.500811334e-13 MLMG: Timers: Solve = 0.455904144 Iter = 0.448000623 Bottom = 0.005240327 Done calling nodal solver Timestep 1 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.184800632 seconds MAC Proj :0.103377854 seconds Nodal Proj :0.481763225 seconds Reactions :0.010023217 seconds Misc :0.009877468 seconds Base State :0.013885042 seconds Time to advance time step: 0.789980307 Call to estdt for level 0 gives dt_lev = 0.3128878797 Minimum estdt over all levels = 0.3128878797 Call to estdt at beginning of step 2 gives dt =0.3128878797 dt_growth factor limits the new dt = 6.698819445e-05  Timestep 2 starts with TIME = 6.089835859e-05 DT = 6.698819445e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.050043585e-05 MLMG: Initial residual (resid0) = 3.050043585e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 2.2848142e-15, 7.49108705e-11 MLMG: Timers: Solve = 0.047843477 Iter = 0.04540862 Bottom = 0.014312638 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.059063412e-05 MLMG: Initial residual (resid0) = 5.66083759e-06 MLMG: Final Iter. 10 resid, resid/bnorm = 4.892627475e-16, 1.599387399e-11 MLMG: Timers: Solve = 0.050604059 Iter = 0.04925883 Bottom = 0.014616224 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003894013591 MLMG: Initial residual (resid0) = 0.003894013591 MLMG: Final Iter. 7 resid, resid/bnorm = 5.66929316e-16, 1.455899685e-13 MLMG: Timers: Solve = 0.442540944 Iter = 0.434745911 Bottom = 0.0038276 Done calling nodal solver Timestep 2 ends with TIME = 0.000127886553 DT = 6.698819445e-05 Timing summary: Advection :0.179539004 seconds MAC Proj :0.106696488 seconds Nodal Proj :0.46467848 seconds Reactions :0.00979193 seconds Misc :0.009580951 seconds Base State :0.010007296 seconds Time to advance time step: 0.770482138 Call to estdt for level 0 gives dt_lev = 0.3130286362 Minimum estdt over all levels = 0.3130286362 Call to estdt at beginning of step 3 gives dt =0.3130286362 dt_growth factor limits the new dt = 7.36870139e-05  Timestep 3 starts with TIME = 0.000127886553 DT = 7.36870139e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.168800511e-05 MLMG: Initial residual (resid0) = 3.168800511e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 5.650713492e-16, 1.783234215e-11 MLMG: Timers: Solve = 0.052614872 Iter = 0.049977684 Bottom = 0.015532696 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.178722337e-05 MLMG: Initial residual (resid0) = 1.012935749e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 6.83363312e-16, 2.149804983e-11 MLMG: Timers: Solve = 0.051345997 Iter = 0.049943211 Bottom = 0.014761749 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004283414244 MLMG: Initial residual (resid0) = 0.004283414244 MLMG: Final Iter. 7 resid, resid/bnorm = 6.424982074e-16, 1.499967481e-13 MLMG: Timers: Solve = 0.447812385 Iter = 0.439807047 Bottom = 0.003849762 Done calling nodal solver Timestep 3 ends with TIME = 0.0002015735669 DT = 7.36870139e-05 Timing summary: Advection :0.190681873 seconds MAC Proj :0.112842188 seconds Nodal Proj :0.470513682 seconds Reactions :0.010402765 seconds Misc :0.010395925 seconds Base State :0.013111347 seconds Time to advance time step: 0.794970898 Call to estdt for level 0 gives dt_lev = 0.3130285358 Minimum estdt over all levels = 0.3130285358 Call to estdt at beginning of step 4 gives dt =0.3130285358 dt_growth factor limits the new dt = 8.105571529e-05  Timestep 4 starts with TIME = 0.0002015735669 DT = 8.105571529e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.570538736e-05 MLMG: Initial residual (resid0) = 3.570538736e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 7.571085414e-16, 2.12043223e-11 MLMG: Timers: Solve = 0.054362807 Iter = 0.052094977 Bottom = 0.01543755 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.581452755e-05 MLMG: Initial residual (resid0) = 1.504387741e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 8.870145964e-16, 2.476689369e-11 MLMG: Timers: Solve = 0.050439928 Iter = 0.049063288 Bottom = 0.014500023 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004711755906 MLMG: Initial residual (resid0) = 0.004711755906 MLMG: Final Iter. 7 resid, resid/bnorm = 7.019124865e-16, 1.489704688e-13 MLMG: Timers: Solve = 0.443555935 Iter = 0.435478924 Bottom = 0.00426609 Done calling nodal solver Timestep 4 ends with TIME = 0.0002826292822 DT = 8.105571529e-05 Timing summary: Advection :0.179765953 seconds MAC Proj :0.113089777 seconds Nodal Proj :0.464906016 seconds Reactions :0.010145755 seconds Misc :0.010024106 seconds Base State :0.012798302 seconds Time to advance time step: 0.778150565 Call to estdt for level 0 gives dt_lev = 0.313028505 Minimum estdt over all levels = 0.313028505 Call to estdt at beginning of step 5 gives dt =0.313028505 dt_growth factor limits the new dt = 8.916128682e-05  Timestep 5 starts with TIME = 0.0002826292822 DT = 8.916128682e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.013180326e-05 MLMG: Initial residual (resid0) = 4.013180326e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 9.681417181e-16, 2.412405224e-11 MLMG: Timers: Solve = 0.052338521 Iter = 0.049696921 Bottom = 0.015297265 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.025185748e-05 MLMG: Initial residual (resid0) = 2.044985444e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 1.11103787e-15, 2.760215155e-11 MLMG: Timers: Solve = 0.050510036 Iter = 0.049167335 Bottom = 0.014549085 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.005182931901 MLMG: Initial residual (resid0) = 0.005182931901 MLMG: Final Iter. 7 resid, resid/bnorm = 7.639288507e-16, 1.47393187e-13 MLMG: Timers: Solve = 0.449267973 Iter = 0.441596279 Bottom = 0.004880652 Done calling nodal solver Timestep 5 ends with TIME = 0.000371790569 DT = 8.916128682e-05 Timing summary: Advection :0.188979308 seconds MAC Proj :0.111896144 seconds Nodal Proj :0.474714173 seconds Reactions :0.010606658 seconds Misc :0.011953337 seconds Base State :0.013795946 seconds Time to advance time step: 0.798339878 Writing plotfile 5 Time to write plotfile: 0.052584188 Total Time: 5.153572481 Unused ParmParse Variables: [TOP]::amr.check_file(nvals = 1) :: [RT_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] [TOP]::amr.ref_ratio(nvals = 4) :: [2, 2, 2, 2] Total GPU global memory (MB): 12049 Free GPU global memory (MB): 11441 [The Arena] space allocated (MB): 9037 [The Arena] space used (MB): 0 [The Device Arena] space allocated (MB): 8 [The Device Arena] space used (MB): 0 [The Pinned Arena] space allocated (MB): 8 [The Pinned Arena] space used (MB): 0 AMReX (25.02-5-g78bdf0faabc4) finalized