Initializing AMReX (25.07)... Initializing CUDA... CUDA initialized with 1 device. AMReX (25.07) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = cutoff densities: low density cutoff (for mapping the model) = 1e-10 buoyancy cutoff density (for zeroing rho - rho_0, centrifugal term) = 5e-10 anelastic cutoff = 1e-10 Maximum HSE Error = 4.547473509e-13 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile RT_pltInitData after InitData Time to write plotfile: 0.067551843 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.005465455 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile RT_pltafter_InitProj after InitProj Time to write plotfile: 0.058926506 Call to firstdt for level 0 gives dt_lev = 0.0006089835859 Multiplying dt_lev by init_shrink; dt_lev = 6.089835859e-05 Minimum firstdt over all levels = 6.089835859e-05 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.005680451 Iter = 0 Bottom = 0 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.08660444773 Minimum estdt over all levels = 0.08660444773 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.08660444773 Multiplying dt by init_shrink; dt = 0.008660444773 Ignoring this new dt since it's larger than the previous dt = 6.089835859e-05 Writing plotfile RT_pltafter_DivuIter after final DivuIter Time to write plotfile: 0.052228035 Doing initial pressure iteration #1  Timestep 0 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 0.002421164472 MLMG: Initial residual (resid0) = 0.002421164472 MLMG: Final Iter. 9 resid, resid/bnorm = 1.751907776e-13, 7.235806556e-11 MLMG: Timers: Solve = 0.042488007 Iter = 0.040585958 Bottom = 0.01283185 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 0.002421205691 MLMG: Initial residual (resid0) = 2.151449931e-06 MLMG: Final Iter. 7 resid, resid/bnorm = 9.927908782e-14, 4.100398747e-11 MLMG: Timers: Solve = 0.031614262 Iter = 0.030275708 Bottom = 0.009080298 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 58.12657035 MLMG: Initial residual (resid0) = 58.12657035 MLMG: Final Iter. 7 resid, resid/bnorm = 8.540723684e-12, 1.46933212e-13 MLMG: Timers: Solve = 0.425866428 Iter = 0.420173846 Bottom = 0.000640381 Done calling nodal solver Timestep 0 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.223193256 seconds MAC Proj :0.084473015 seconds Nodal Proj :0.450307806 seconds Reactions :0.013235796 seconds Misc :0.011855176 seconds Base State :0.014238986 seconds Time to advance time step: 0.78326629 Writing plotfile 0 after all initialization Time to write plotfile: 0.056123605 Beginning main evolution  Timestep 1 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.394238647e-05 MLMG: Initial residual (resid0) = 2.394238647e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 3.18262753e-16, 1.32928584e-11 MLMG: Timers: Solve = 0.043015018 Iter = 0.041000068 Bottom = 0.012819087 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.394218844e-05 MLMG: Initial residual (resid0) = 1.928423484e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 6.036517941e-16, 2.521289128e-11 MLMG: Timers: Solve = 0.040420513 Iter = 0.039087419 Bottom = 0.01119237 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003539812449 MLMG: Initial residual (resid0) = 0.003539812449 MLMG: Final Iter. 7 resid, resid/bnorm = 5.352706126e-16, 1.512143991e-13 MLMG: Timers: Solve = 0.430049347 Iter = 0.42395887 Bottom = 0.000914004 Done calling nodal solver Timestep 1 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.212321626 seconds MAC Proj :0.092473776 seconds Nodal Proj :0.454433633 seconds Reactions :0.011514551 seconds Misc :0.017963549 seconds Base State :0.013085959 seconds Time to advance time step: 0.788942403 Call to estdt for level 0 gives dt_lev = 0.3128878797 Minimum estdt over all levels = 0.3128878797 Call to estdt at beginning of step 2 gives dt =0.3128878797 dt_growth factor limits the new dt = 6.698819445e-05  Timestep 2 starts with TIME = 6.089835859e-05 DT = 6.698819445e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.050043585e-05 MLMG: Initial residual (resid0) = 3.050043585e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 2.2848142e-15, 7.49108705e-11 MLMG: Timers: Solve = 0.042616067 Iter = 0.040545309 Bottom = 0.012362502 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.059063412e-05 MLMG: Initial residual (resid0) = 5.66083759e-06 MLMG: Final Iter. 10 resid, resid/bnorm = 4.89262324e-16, 1.599386015e-11 MLMG: Timers: Solve = 0.044961953 Iter = 0.043634201 Bottom = 0.012653587 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003894013591 MLMG: Initial residual (resid0) = 0.003894013591 MLMG: Final Iter. 7 resid, resid/bnorm = 5.70940864e-16, 1.466201519e-13 MLMG: Timers: Solve = 0.427300457 Iter = 0.421884596 Bottom = 0.000911076 Done calling nodal solver Timestep 2 ends with TIME = 0.000127886553 DT = 6.698819445e-05 Timing summary: Advection :0.208843407 seconds MAC Proj :0.096175582 seconds Nodal Proj :0.451636428 seconds Reactions :0.010877431 seconds Misc :0.011459581 seconds Base State :0.011023841 seconds Time to advance time step: 0.779191926 Call to estdt for level 0 gives dt_lev = 0.3130286362 Minimum estdt over all levels = 0.3130286362 Call to estdt at beginning of step 3 gives dt =0.3130286362 dt_growth factor limits the new dt = 7.36870139e-05  Timestep 3 starts with TIME = 0.000127886553 DT = 7.36870139e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.168800511e-05 MLMG: Initial residual (resid0) = 3.168800511e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 5.650713492e-16, 1.783234215e-11 MLMG: Timers: Solve = 0.047137844 Iter = 0.044550863 Bottom = 0.013331715 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.178722337e-05 MLMG: Initial residual (resid0) = 1.012935749e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 6.833616179e-16, 2.149799653e-11 MLMG: Timers: Solve = 0.045101816 Iter = 0.043767637 Bottom = 0.012655461 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004283414244 MLMG: Initial residual (resid0) = 0.004283414244 MLMG: Final Iter. 7 resid, resid/bnorm = 6.724221874e-16, 1.569827593e-13 MLMG: Timers: Solve = 0.431104638 Iter = 0.425522906 Bottom = 0.001020427 Done calling nodal solver Timestep 3 ends with TIME = 0.0002015735669 DT = 7.36870139e-05 Timing summary: Advection :0.212975145 seconds MAC Proj :0.100964299 seconds Nodal Proj :0.455751737 seconds Reactions :0.011324836 seconds Misc :0.012647371 seconds Base State :0.013741559 seconds Time to advance time step: 0.793864295 Call to estdt for level 0 gives dt_lev = 0.3130285358 Minimum estdt over all levels = 0.3130285358 Call to estdt at beginning of step 4 gives dt =0.3130285358 dt_growth factor limits the new dt = 8.105571529e-05  Timestep 4 starts with TIME = 0.0002015735669 DT = 8.105571529e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.570538736e-05 MLMG: Initial residual (resid0) = 3.570538736e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 7.571119296e-16, 2.120441719e-11 MLMG: Timers: Solve = 0.046500548 Iter = 0.044507156 Bottom = 0.013351118 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.581452755e-05 MLMG: Initial residual (resid0) = 1.504387741e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 8.870145964e-16, 2.476689369e-11 MLMG: Timers: Solve = 0.045008706 Iter = 0.04367095 Bottom = 0.012629709 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004711755906 MLMG: Initial residual (resid0) = 0.004711755906 MLMG: Final Iter. 7 resid, resid/bnorm = 7.042977312e-16, 1.494767015e-13 MLMG: Timers: Solve = 0.432361609 Iter = 0.426534536 Bottom = 0.000860732 Done calling nodal solver Timestep 4 ends with TIME = 0.0002826292822 DT = 8.105571529e-05 Timing summary: Advection :0.214701228 seconds MAC Proj :0.10022704 seconds Nodal Proj :0.456107195 seconds Reactions :0.011114434 seconds Misc :0.018480697 seconds Base State :0.012044895 seconds Time to advance time step: 0.800843485 Call to estdt for level 0 gives dt_lev = 0.313028505 Minimum estdt over all levels = 0.313028505 Call to estdt at beginning of step 5 gives dt =0.313028505 dt_growth factor limits the new dt = 8.916128682e-05  Timestep 5 starts with TIME = 0.0002826292822 DT = 8.916128682e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.013180326e-05 MLMG: Initial residual (resid0) = 4.013180326e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 9.68140871e-16, 2.412403113e-11 MLMG: Timers: Solve = 0.046338576 Iter = 0.044307698 Bottom = 0.013193682 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.025185748e-05 MLMG: Initial residual (resid0) = 2.044985444e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 1.111034482e-15, 2.760206737e-11 MLMG: Timers: Solve = 0.044934892 Iter = 0.043607785 Bottom = 0.012632783 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.005182931901 MLMG: Initial residual (resid0) = 0.005182931901 MLMG: Final Iter. 7 resid, resid/bnorm = 7.589415207e-16, 1.464309266e-13 MLMG: Timers: Solve = 0.426723081 Iter = 0.421087316 Bottom = 0.000626642 Done calling nodal solver Timestep 5 ends with TIME = 0.000371790569 DT = 8.916128682e-05 Timing summary: Advection :0.209930663 seconds MAC Proj :0.099857468 seconds Nodal Proj :0.452931962 seconds Reactions :0.011264215 seconds Misc :0.010931242 seconds Base State :0.012686702 seconds Time to advance time step: 0.785127691 Writing plotfile 5 Time to write plotfile: 0.056286028 Total Time: 5.176498853 Unused ParmParse Variables: [TOP]::amr.check_file(nvals = 1) :: [RT_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] [TOP]::amr.ref_ratio(nvals = 4) :: [2, 2, 2, 2] Total GPU global memory (MB): 12049 Free GPU global memory (MB): 11441 [The Arena] max space allocated (MB): 9037 [The Arena] max space used (MB): 177 [The Device Arena] max space allocated (MB): 8 [The Device Arena] max space used (MB): 0 [The Pinned Arena] max space allocated (MB): 8 [The Pinned Arena] max space used (MB): 5 AMReX (25.07) finalized